UL- E U C E R T I F I C A T E

Transcription

1 UL- E U C E R T I F I C A T E Page 1/6 Certificate Holder Manufacturer Certified Product Type Product Trade Name Trademark Rating/Classification Polyseam AS Ravneveien 7 Linnestad Næringsområde N-3174 Revetal, Norway Polyseam Ltd Shaw Park Silver Street Huddersfield, West Yorkshire HD5 9AF, UK Fire Stop - ant IPT ant N/A See Appendix Harmonised Technical Specifications ETAG / EN Supporting Documentation ETA 14/0041, EC CERTIFICATE OF CONFORMITY CPR 0164, Classification Report No. 13CA40986 Additional information Additional test evidence is held on file Expiry date Certification Manager Chris Miles This is to certify that representative samples of the Certified Product listed above have been investigated by Underwriters Laboratories to the Standard(s) indicated on this Certificate, in accordance with the UL Global Services Agreement and the UL-EU Mark Service Terms and Conditions ( Agreement ). The Certificate Holder is entitled to use the UL-EU Mark for the Certified Product listed on the certificate and manufactured at the production site(s) listed, in accordance with the terms of the Agreement. Only those products bearing the UL-EU Mark for Europe should be considered as being covered by UL s UL-EU Mark Service. This Certificate shall remain valid through the Expiration date, unless a Standard identified on this Certificate is amended or withdrawn prior to that date or there is a non-compliance with the Agreement.

2 A p p e n d i x U L - E U C E R T I F I C A T E Page 2/6 This certificate relates to the use of IPT ant for fire stopping where there are joints in or between walls and floors. The detailed scope is given in pages 3 to 5 of this Certificate. This shows the thickness and acceptable dimensions, substrates and orientations required to provide fire resistance periods of up to 240 minutes for differing wall/floor constructions. The product is certificated on the basis of: i) ETA 14/0041 ii) EC CERTIFICATE OF CONFORMITY CPR 0164 iii) Classification report No. 13CA40986 iv) Inspection and surveillance of factory production control by UL v) Fire resistance test data in accordance with EN : 2006 vi) Classification in accordance with EN vii) Durability and Serviceability as defined in ETAG The durability class of IPT ant is X - intended for use at conditions exposed to weathering. Includes lower use categories. IPT ant is a sealant used to form linear gap seals where gaps are present in wall and floor constructions and linear joint seals where wall and floor constructions abut. The IPT ant is supplied in liquid form contained within 200 ml, 300 ml, 380 mm and 600 ml containers. The sealant is gunned into the aperture in the separating element/elements to a specified depth utilising mineral fibre insulation backing material.

3 A p p e n d i x U L - E U C E R T I F I C A T E Page 3/6 Product: IPT ant Product-type: ant Basic requirement for construction work Basic Requirement Intended use: Linear Joint & Gap BWR 1 Mechanical resistance and stability Performance - None Not relevant BWR 2 Safety in case of fire EN Reaction to fire Class D-s2, d0 EN Resistance to fire See pages 4 & 5 BWR 3 Hygiene, health and environment EN 1026:2000 Air permeability (material property) No performance determined ETAG 026-3, Annex C Water permeability (material property) No performance determined Declaration of manufacturer Release of dangerous substances Declaration of manufacturer BWR 4 Safety in use EOTA TR 001:2003 Mechanical resistance and stability No performance determined EOTA TR 001:2003 Resistance to impact/movement No performance determined EOTA TR 001:2003 ISO Adhesion BWR 5 Protection against noise No performance determined EN / EN ISO Airborne sound insulation Rw(C;Ctr)= 45 (-3;-10) db* EN / EN ISO Impact sound insulation No performance determined BWR 6 Energy economy and heat retention EN 12664, EN or EN Thermal properties No performance determined EN ISO EN ISO 8339: 2005, ISO 9046: 2004 & ISO 7389: 2003 * At minimum 12 mm depth Water vapour permeability General aspects relating to fitness for use Durability and serviceability BWR 7 Sustainable use of natural resources No performance determined - - No performance determined X

4 A p p e n d i x U L - E U C E R T I F I C A T E Page 4/6 IPT ant: Linear Gaps Head of Flexible Wall to Concrete Floor Soffit s Thickness Maximum Gap Size Position Material Fire Resistance (mins.) E EI Plasterboard & Concrete Both Sides 12.5 Rockwool Flexi 35 kg/m 3 plus 50 mm steel partition head track IPT ant: Linear Gaps Within Flexible Walls up to 3m High or Rigid Walls Thickness Maximum Gap Size Position Material Fire Resistance (mins.) E EI Plasterboard /Masonry/ Concrete Both Sides 12.5 Rockwool Flexi kg/m 3 Gap may be vertical or horizontal orientated. Gaps in flexible partition constructions shall be additionally constructed such that a 50 mm partition stud or channel lines each side of the gap positioned with the section s web towards the gap.

5 A p p e n d i x U L - E U C e r t i f i c a t e Certification Mark UL-EU mark Page 5/6 Thickness IPT ant: Linear Gaps Within Concrete Floors Maximum Gap Size Concrete Position Both Sides 15 to each side Soffit 25 Material Fire Resistance (mins.) E EI Rockwool Flexi 33 kg/m Protecta Mineral Fibre BIO kg/m3 Soffit mounted seals shall be arranged such that the sealant is on the upper surface of the backing material.

6 A p p e n d i x U L - E U C e r t i f i c a t e Certification Mark UL-EU mark Page 6/6 The UL-EU Mark, as displayed below, shall appear on certified products only. size is not specified, as long as the Mark is legible. The following is suggested. The minimum height of the registered trademark symbol shall be 1 mm. When the overall diameter of the UL-EU Mark is less than 9.5 mm, the trademark symbol may be omitted if it is not legible to the naked eye. The UL-EU Mark may appear on a label, nameplate, or may be cast, stamped or molded into the product. When appearing on a label or nameplate, the Manufacturer s name or trademark along with a model number are also required on that same label or nameplate. If cast, stamped or molded, the Certificate Manufacturer s name or trademark and model number shall also appear elsewhere on the product. All content shall be in accordance with the details provided on this UL-EU Certificate. PROCUREMENT The Production site may reproduce the Mark or obtain it from a UL authorized supplier. The list of UL authorized suppliers can be found on UL s online directory at