TEST REPORT. Rendered to: TREMCO, INCORPORATED Beachwood, Ohio

Transcription

1 TEST REPORT Report No.: E Rendered to: TREMCO, INCORPORATED Beachwood, Ohio PRODUCT TYPE: Wall Panel System SERIES/MODEL: ExoAir 230, Dymonic 100 SPECIFICATION: ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure. Test Date: 07/21/15 And: 07/22/15 Test Record Retention Date: 07/22/ Lincoln Avenue Springdale, PA p f

2 1.0 Report Issued To: TREMCO, INCORPORATED 3735 Green Road P.O. Box 1014 Beachwood, Ohio Test Report No.: E Page 1 of Test Laboratory: Architectural Testing, Inc., a subsidiary of Intertek (Intertek- ATI) 1140 Lincoln Avenue Springdale, Pennsylvania Project Summary: 3.1 Product Type: Wall Panel System 3.2 Series/Model: ExoAir 230, Dymonic Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The mock-ups tested were representative of target installation methods. Testing was performed on one penetrated wall. 3.4 Test Dates: 07/21/2015 and 07/22/ Test Location: Tremco Incorporated test facility in Cleveland, Ohio. 3.6 Test Sample Source: The test specimen was provided by the client. 3.7 Test Specimen Installation: The test specimen was installed by representatives from Tremco, Incorporated. 3.8 List of Official Observers: Name Company Steven Kraynik Brian Venturini Tremco, Inc. Intertek-ATI

3 Page 2 of Test Specification(s): ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure 5.0 Test Specimen Description: 5.1 Product Sizes: Overall Area: Width Height 5.9 m² (64.0 ft 2 ) millimeters inches millimeters inches Overall size Test Wall Test Wall Construction: The wall was constructed of 2 x 4, 8" 20 gauge galvanized steel studs, secured into a steel track at the top and bottom with #8 x 3/4" self-tapping tech screws then wrapped with a 2 x 10" SPF wooden buck. 1/2" sheet rock was then attached to the exterior with #6 x 1-1/4"self-tapping tech screws spaced evenly every 8" around perimeter and 12"up the studs. The sheeting installation allowed for 8' x 1/8" horizontal board joint at the center. The joint was taped with joint compound applied over top. Dymonic 100 polyurethane sealant was used to treat the perimeter joints to the wooden buck. All fasteners were detailed with joint compound. After the compound was fully cured a 75 wet mils of ExoAir 230 air barrier was applied to the exterior 6.0 Test Results: (Continued) Title of Test Pressure Test Results Water Penetration, per ASTM E Pa (2.92 psf) No penetration

4 Page 3 of 4 The service life of this report will expire on the stated Test Record Retention End Date, at which time such materials as drawings, data sheets, samples of test specimens, copies of this report, and any other pertinent project documentation, shall be discarded without notice. If test specimen contains glazing, no conclusions of any kind regarding the adequacy or inadequacy of the glass in any glazed test specimen(s) can be made. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written approval of Intertek-ATI. For INTERTEK-ATI Brian D. Venturini Technician Lynn George Director Regional Operations BDV:sld Attachments (pages): This report is complete only when all attachments listed are included. Appendix-A: Photographs (2) This report produced from controlled document template ATI 00523, issued 10/27/11.

5 Page 4 of 4 Revision Log Rev. # Date Page(s) Revision(s) 1 08/19/15 Photographs Corrected two photographs

6 Appendix A Photographs Photo No. 1 Exterior of Test Specimen

7 Photo No. 2 Interior of Test Specimen