Cobra. Innovative shielded low profile right angle connector plug and backshell assemblies reduce MIGHTY MOUSE

Transcription

1 MIGHTY MOUSE Cobra The Ultra-Low Profile EMI/RFI Plug and ackshell Assembly Innovative shielded low profile right angle connector plug and backshell assemblies reduce clearance requirements without compromising ruggedness or shielding performance. Available in Series 801 double-start, Series 804 QDC push-pull, and Series 805 triple-start, Cobra assemblies provide optimal low-profile cable routing and legendary Mighty Mouse connector performance in a single package. Each Cobra assembly is equipped with a removable rear cover and gasket for easy crimp or solder contact termination of the connector. oth pin and socket versions are available for both crimp and solder terminated versions. Integrated lowprofile backshell is equipped with an EMI/RFI shield termination platform and a shrink boot lip. The ultra-lightweight assembly may be clocked in eight different angle orientations for additional flexibility in cable routing. Connectors are equipped with polarization keying to prevent mismating. Glenair Mighty Mouse Cobra connector and backshell assemblies mate with available square flange and jam nut receptacles from each respective connector series. Fourteen contact arrangements are available, all with Size #23 contacts from shell size 5 to shell size 21 with contacts respectively. Connector shells are aluminum alloy or stainless steel. Space-saving design features one-piece machined and brazed connector shell and right angle backshell for minimum height and optimal EMI performance. Master key clocking enables easy cable entry/ exit routing in eight angles Removable rear cover and gasket provides easy access to end of connector for crimp or solder contact termination For more information contact Glenair at or visit our website at

2 MIGHTY MOUSE Cobra TECHNICAL SPECIFICATIONS triple-start with self-locking coupling nut, exploded view How To Order Mighty Mouse Cobra Plug Connector and ackshell Assemblies Sample Part Number ZNU 8-13 P A 1 05 Thread Master Key Connector Series and Mighty Mouse Cobra asic Part Number Double-Start self-locking plug with ratchet mechanism (the clicker) QDC Push-Pull plug Triple-Start plug with ratcheting anti-decoupling mechanism Material/Finish M, MT, NF, ZNU, Z1 - See Table I Shell Size - Contact Arrangement See Table V - A: : C: F Contact Style Polarization Key Position Cable Exit Direction Cable Entry Size A = Pin, solder = Socket, solder P = Pin, Crimp S = Socket, crimp A,, C, D, E, F - See Table III 1, 2, 3, 4, 5, 6,, 8 - See Table IV See Table VI ØC J Specifications Current Rating: #23 5 Amps Test Voltage (DWV) #23: 500 VAC Sea Level Insulation Resistance: 5000 megohms minimum Contact Resistance: 3 millivolt drop at 5 Amp test current Mating Cycles Series 801 and 804: 2000; Series 805: 500 Operating Temperature: -55 C. to +150 C. Shielding Effectiveness: 50 d min from 100MHz to 1000MHz. Magnetic Permeability: 2.0µ Vibration: 3g / Shock: 300g Immersion, mated: 1meter water immersion for 1 hour Materials/finish Contacts: Copper alloy, gold plated ackshell Housing and Lid: Aluminum or Stainless Steel ackshell Sealing Gasket and Interfacial Seal: Fluorosilicone Screws: 300 Series Stainless Steel Insulator: LCP Notes Rear insulator grommet not supplied. Cobra plug connectors mate with respective series receptacles with same polarization and opposite contact gender. Hand crimp tool: P/N Positioner for hand tool: P/N Insertion/extraction tool P/N Crimp barrel accommodates 22, 24, 26 and 28 gage wire. All Cobra plugs equipped with Size #23 contacts. Table I: Shell Material/Finish Symbol Material Finish M Electroless Nickel (RoHS) NF Aluminum Cad/O.D. over Electroless Nickel MT Alloy Nickel-PTFE (RoHS) ZNU lack Zinc Nickel over Electroless Nickel Z1 Stainless Steel Passivate Table III: Key Positions Table IV: Exit Direction Table VI - Cable Entry Direction C Code Entry Size A A C A Master C Key D *.813 E *.85 F * * Direction 2 Shown 1* * Entry codes 13-1 not available for Series 804 Cobra Table V - Shell Size/Contact Arrangements A: : C: Shell Size Contact Arrangement Max Entry Shell Size Contact Arrangement Max Entry Shell Size Contact Arrangement Max Entry , 8-6, , 6-6, , 6-6,

3 GS SERIES 801, RATCHETING, 10C N.A. N.A. A CORA STYLE

4 THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO E DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE Y ANYONE OTHER THAN WITHOUT WRITTEN PERMISSION FROM THE INFORMATION HEREIN HAS EEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY E USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM SHELL SIZE A øa.65 [16.5].65 [16.5].69 [1.5].9 [20.1].83 [21.1].92 [23.4] 1.10 [2.9] 1.34 [34.0] 1.45 [36.8] 1.50 [38.1] 1.65 [41.9] POSITION THREAD P-.1L P-.1L P-.1L P-.1L P-.1L P-.1L P-.1L P-.2L P-.2L P-.2L P-.2L P-.2L-2 TALE III - POSITION POSITION A A (NORMAL) C D E 5 25 F TALE II - DIMENSIONAL DATA D E F.84 [21.3].32 [8.1] 1.21 [30.].86 [21.8].34 [8.6] 1.24 [31.5].88 [22.4].39 [9.9] 1.28 [32.5].89 [22.6].42 [10.] 1.31 [33.3].92 [23.4].45 [11.4] 1.34 [34.0].96 [24.4].48 [12.2] 1.3 [34.8] 1.13 [28.].52 [13.2] 1.48 [3.6] 1.28 [32.5].63 [16.0] 1.8 [45.2] G 1.40 [35.6] 1.42 [36.1] 1.44 [36.6] 1.45 [36.8] 1.48 [3.6] 1.52 [38.6] 1.80 [45.] 1.92 [48.8] REAR-MOUNTED SQUARE FLANGE H 1.23 [31.2] 1.25 [31.8] 1.2 [32.3] 1.28 [32.5] 1.31 [33.3] 1.35 [34.3] 1.63 [41.4] 1.8 [45.2] J.500 [12.0].560 [14.22].650 [16.51].10 [18.03].0 [19.56].835 [21.21].950 [24.13] [29.9] REVISION HISTORY SEE SHEET 1 OF 2 MAX ENTRY TALE IV-EXIT DIRECTION DIRECTION C TALE VI-CALE ENTRY CODE ENTRY SIZE C (POSITION A SHOWN) PART NUMER DEVELOPMENT EXAMPLE: ZNU 8-13 P A 1 05 SHOWN INSTALLED H MAX.060 [1.52] G MAX CONNECTOR SERIES SHELL STYLE -26 = SELF-LOCKING PLUG WITH RATCHET MECHANISM (THE "CLICKER") CLASS (SEE TALE I) SHELL SIZE - CONTACT ARRANGEMENT (SEE TALE V) SQUARE FLANGE MATING SPACE REQUIREMENT JAM NUT MATING SPACE REQUIREMENT CONTACT STYLE A = PIN, SOLDER = SOCKET, SOLDER P = PIN, CRIMP S = SOCKET, CRIMP A THROUGH F (SEE TALE III) POSITION 1 THROUGH 8 (SEE TALE IV) CALE EXIT DIRECTION CALE ENTRY SIZE (SEE TALE VI) TALE V - AVAILALE ARRANGEMENTS SHELL SIZE CONTACT ARRANGEMENT* , 6-6, *: # FOLLOWING DASH = # OF CONTACTS DIMENSIONS ARE IN INCHES FRACTIONS ± 1/16 DECIMALS.XX ±.03 /F TOLERANCES 10C508 P/C CORA STYLE CODE IDENT. NO. SIZE DRAWING NO A 80 SCALE N.A. WEIGHT N.A. SHEET GS CALE EXIT DIRECTION (DIRECTION 2 SHOWN) SERIES 801, RATCHETING, OF REV

5 THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO E DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE Y ANYONE OTHER THAN WITHOUT WRITTEN PERMISSION FROM THE INFORMATION HEREIN HAS EEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY E USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM CLASS M MT NF ZNU Z1 REVISION HISTORY REV DESCRIPTION DATE A PRODUCTION RELEASE TALE I - MATERIAL / FINISH CLASS REVISED PER DCN # /12/13 SHELL MATERIAL FINISH ALUMINUM ALLOY ELECTROLESS NICKEL (RoHS) ALUMINUM ALLOY NICKEL-PTFE (RoHS) OLIVE DRA CADMIUM OVER ALUMINUM ALLOY ELECTROLESS NICKEL D MAX LACK ZINC-NICKEL OVER A ALUMINUM ALLOY ASSEMLED ELECTROLESS NICKEL (RoHS) STAINLESS STEEL PASSIVATE (RoHS) CONTACT GLENAIR FOR ADDITIONAL FINISHES.60 [15.2] REAR INSULATOR GROMMET NOT SUPPLIED GASKET COVER NOTES: F MAX 1. ASSEMLY TO E IDENTIFIED WITH GLENAIR'S NAME, PART NUMER, AND DATE CODE, SPACE PERMITTING. 2. MATERIAL / FINISH: PLUG ARREL, HOUSING, COVER - ALUMINUM ALLOY OR STAINLESS STEEL / SEE TALE I INSULATOR - LCP / NONE INTERFACIAL SEAL, GASKET - FLUOROSILICONE / NONE CONTACT - COPPER ALLOY / GOLD PLATE PER ASTM 488, TYPE II, CODE C, CLASS 1.25 ( MIN THK), OVER A SUITALE UNDERPLATE CONTACT RETENTION CLIP - ERYLLIUM COPPER ALLOY / NONE HARDWARE - STAINLESS STEEL / PASSIVATE OR LACK OXIDE 3. CONTACTS ARE SIZE CONSULT FACTORY FOR ADDITIONAL CONTACT ARRANGEMENTS AND/OR SHELL ORIENTATIONS. E ASSEMLED ENTRY SIZE J FACE VIEW OF PLUG AS VIEWED FROM ENGAGING END (8-13PA1 SHOWN) 5. CRIMP ARREL ACCOMMODATES 22, 24, 26, AND 28 GAGE WIRE. 6. CRIMP TOOL DATA: A. HAND CRIMP TOOL: GLENAIR PART NO POSITIONER FOR HAND TOOL: GLENAIR PART NO C. INSERTION/EXTRACTION TOOL: GLENAIR PART NO CONTACT ARRANGEMENT, CONTACT GENDER, POSITIONS, AND SHELL ORIENTATION SHOWN ARE FOR REFERENCE ONLY. 8. THIS CONNECTOR MATES WITH ALL QUICK-DISCONNECT, HIGH DENSITY CONNECTORS WITH SAME POLARIZATION AND OPPOSITE CONTACT GENDER ( THROUGH , , , AND ). 9. REAR INSULATOR GROMMET NOT SUPPLIED. DIMENSIONS ARE IN INCHES FRACTIONS ± 1/16 DECIMALS.XX ±.03 /F TOLERANCES 12C3202 P/C CORA STYLE CODE IDENT. NO. SIZE DRAWING NO A 80 SCALE N.A. WEIGHT N.A. SHEET JMT SERIES 804, OF REV

6 THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO E DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE Y ANYONE OTHER THAN WITHOUT WRITTEN PERMISSION FROM THE INFORMATION HEREIN HAS EEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY E USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM TALE II - DIMENSIONAL DATA SHELL SIZE øa D E F G H J MAX ENTRY 5.6 [1.0].2 [6.9] 1.03 [26.2].29 [.4] 1.24 [31.5] 1.31 [33.4] 1.16 [29.5].500 [12.] [19.1].30 [.6] 1.08 [2.4].31 [.9] 1.2 [32.3] 1.36 [34.5] 1.21 [30.].560 [14.2] [22.4].34 [8.6] 1.20 [30.5].36 [9.1] 1.31 [33.3] 1.4 [3.3] 1.32 [33.5].650 [16.5] [24.6].38 [9.] 1.24 [31.5].39 [9.9] 1.34 [34.0] 1.51 [38.4] 1.36 [34.5].10 [18.0] [26.9].41 [10.4] 1.30 [33.0].42 [10.] 1.3 [34.8] 1.58 [40.1] 1.43 [36.3].0 [19.6] [29.2].44 [11.2] 1.35 [34.3].45 [11.4] 1.40 [35.6] 1.62 [41.1] 1.4 [3.3].835 [21.2] [33.8].50 [12.] 1.44 [36.6].49 [12.4] 1.51 [38.4] 1.1 [43.4] 1.56 [39.6].950 [24.1] ([4.1] ).31 ([8.0] ) REVISION HISTORY SEE SHEET 1 OF TALE VI-CALE ENTRY CODE ENTRY SIZE A POSITION (POSITION A SHOWN) PART NUMER DEVELOPMENT TALE III - POSITION POSITION A A (NORMAL) C D E 5 25 F H MAX SHOWN INSTALLED FRONT-MOUNTED SHOWN INSTALLED G MAX REAR-MOUNTED TALE IV-EXIT DIRECTION DIRECTION C C EXAMPLE: ZNU 8-13 P A 1 05 CONNECTOR SERIES SHELL STYLE -06 = PLUG CLASS (SEE TALE I) SHELL SIZE - CONTACT ARRANGEMENT (SEE TALE V) CONTACT STYLE A = PIN, SOLDER = SOCKET, SOLDER P = PIN, CRIMP S = SOCKET, CRIMP POSITION A THROUGH F (SEE TALE III) OMIT FOR SINGLE CALE EXIT DIRECTION 1 THROUGH 8 (SEE TALE IV) CALE ENTRY SIZE (SEE TALE VI) TALE V - AVAILALE ARRANGEMENTS SHELL SIZE CONTACT ARRANGEMENT* , 6-6, *: # FOLLOWING DASH = # OF CONTACTS FRONT-MOUNTED MATING SPACE REQUIREMENT DIMENSIONS ARE IN INCHES TOLERANCES FRACTIONS ± 1/16 DECIMALS.XX ±.03 JMT REAR-MOUNTED MATING SPACE REQUIREMENT CODE IDENT. NO. SIZE A SERIES 804, CORA STYLE /F 12C3202 P/C 80 N.A. N.A. CALE EXIT DIRECTION (DIRECTION 2 SHOWN) DRAWING NO SCALE WEIGHT SHEET OF REV.

7 THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO E DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE Y ANYONE OTHER THAN WITHOUT WRITTEN PERMISSION FROM THE INFORMATION HEREIN HAS EEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY E USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM TALE I - MATERIAL / FINISH CLASS CLASS SHELL MATERIAL FINISH M ALUMINUM ALLOY ELECTROLESS NICKEL (RoHS) MT ALUMINUM ALLOY NICKEL-PTFE (RoHS) NF ALUMINUM ALLOY ZNU ALUMINUM ALLOY OLIVE DRA CADMIUM OVER ELECTROLESS NICKEL LACK ZINC-NICKEL OVER ELECTROLESS NICKEL (RoHS) Z1 STAINLESS STEEL PASSIVATE (RoHS) CONTACT GLENAIR FOR ADDITIONAL FINISHES D MAX ASSEMLED REVISION HISTORY REV DESCRIPTION DATE A PRODUCTION RELEASE 0/19/12 REVISED PER DCN # /12/13 THREAD REAR INSULATOR GROMMET NOT SUPPLIED øa GASKET NOTES: 1. ASSEMLY TO E IDENTIFIED WITH GLENAIR'S NAME, PART NUMER, AND DATE CODE, SPACE PERMITTING. COVER F 2. MATERIAL / FINISH: PLUG ARREL, COUPLING NUT, HOUSING, COVER - ALUMINUM ALLOY OR STAINLESS STEEL / SEE TALE I INSULATOR - LCP / NONE. INTERFACIAL SEAL, GASKET - FLUOROSILICONE / NONE CONTACT - COPPER ALLOY / GOLD PLATE PER ASTM 488, TYPE II, CODE C, CLASS 1.25 ( MIN THK), OVER A SUITALE UNDERPLATE CONTACT RETENTION CLIP - ERYLLIUM COPPER ALLOY / NONE HARDWARE - STAINLESS STEEL / PASSIVATE OR LACK OXIDE RETAINING WIRE - TORLON / NONE DETENT SPRING, RIVET - STAINLESS STEEL / PASSIVATE EMI GROUND SPRING - ERYLLIUM COPPER / ELECTROLESS NICKEL 3. CONTACTS ARE SIZE 23. E MAX ASSEMLED ENTRY SIZE J 4. CONSULT FACTORY FOR ADDITIONAL CONTACT ARRANGEMENTS AND/OR SHELL ORIENTATIONS. 5. CRIMP ARREL ACCOMMODATES 22, 24, 26, AND 28 GAGE WIRE. FACE VIEW OF PLUG AS VIEWED FROM ENGAGING END (10-13PA1 SHOWN) 6. CRIMP TOOL DATA: A. HAND CRIMP TOOL: GLENAIR PART NO POSITIONER FOR HAND TOOL: GLENAIR PART NO C. INSERTION/EXTRACTION TOOL: GLENAIR PART NO CONTACT ARRANGEMENT, CONTACT GENDER, POSITIONS, AND SHELL ORIENTATION SHOWN ARE FOR REFERENCE ONLY. 8. THIS CONNECTOR MATES WITH ALL QUICK COUPLING, HIGH DENSITY CONNECTORS WITH SAME POLARIZATION AND OPPOSITE CONTACT GENDER ( THROUGH AND ). 9. REAR INSULATOR GROMMET NOT SUPPLIED. DIMENSIONS ARE IN INCHES TOLERANCES FRACTIONS ± 1/16 DECIMALS.XX ±.03 GS 0/19/12 0/19/12 0/19/12 0/18/12 CODE IDENT. NO. SIZE A SERIES 805 STYLE RATCHETING CORA DRAWING NO. /F 11C89 P/C 80 0/18/12 N.A. N.A SCALE WEIGHT SHEET OF REV.

8 THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO E DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE Y ANYONE OTHER THAN WITHOUT WRITTEN PERMISSION FROM THE INFORMATION HEREIN HAS EEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY E USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM PART NUMER DEVELOPMENT EXAMPLE: ZNU 9-10 P A 1 05 CONNECTOR SERIES SHELL STYLE -16 = PLUG CONNECTOR WITH RATCHETING ANTI-DECOUPLING MECHANISM CLASS (SEE TALE I) SHELL SIZE - CONTACT ARRANGEMENT (SEE TALE V) CONTACT STYLE A = PIN, SOLDER = SOCKET, SOLDER P = PIN, CRIMP S = SOCKET, CRIMP A THROUGH F (SEE TALE III) POSITION 1 THROUGH 8 (SEE TALE IV) CALE EXIT DIRECTION DECIMAL± 2 CALE ENTRY SIZE (SEE TALE VI) /F P/C 0/18/12 CODE IDENT. NO SIZE DRAWING NO.