Technical Application Guide for UP-SHINE LED Downlight

Transcription

1 Technical Application Guide for UP-SHINE LED Downlight UP-DL W

2 Introduction DL9 Downlight is structural designed with integration of heatsink and surface cover, aims at increasing the heat dissipation area. IP54 waterproof for indoor use, especially for damp locations. UL94-V Fire-rated PC diffuser provides high light transmittance and even light output. It is an ideal replacement for residential and commercial lighting. Up to 7% energy saving compared to standard CFL Long lifetime of 4, hours Triac dim 9 wide beam angle 7mm cutout CCT: 3K 4K 5K 57K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Application notes IP54 for indoor use only Professional electrician for installation only Switch off before installation Do not touch when in use Keep away from hot steam and corrosive gas Application Areas It is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc. Certificate

3 Product Information Ø Technical Specifications Model Driver data Sheet Driver data DIM Non dim Input rated Voltage AC23V AC23V Frequency 5Hz 5Hz Input Voltage AC2-24V AC2-24V Efficiency 78% 78% Total load Wattage 5W±.5W 5W±.5W Power Factor.9.9 Rated input current.28a.28a Full load output Voltage DC28-38V DC25-42V Rated output current 13mA 13mA Output current range 13mA±5% 13mA±5% Power tolerance ±5% ±5% Current output tolerance ±5% ±5% Dimming range 8%-1% Dimmer Triac dimmers Short circuit protection PASS PASS Over voltage protection PASS PASS Over temperature protection PASS PASS THD 2% 2% Withstand voltage AC375V AC375V Fixture Compatibility Rated Wattage Voltage Power Power Factor Electrical Classification Lumen (±5%) Beam angle Ingress Protection CCT Lifespan CRI Dimmable Dimension UP-DL W 23V 5W K 4h 8 No Ø82*47.5mm cutout 7mm UP-DL W 23V 5W K 4h 8 No Ø82*47.5mm cutout 7mm UP-DL W 23V 5W K 4h 8 No Ø82*47.5mm cutout 7mm UP-DL W 23V 5W K 4h 8 No Ø82*47.5mm cutout 7mm UP-DL W-D 23V 5W K 4h 8 Yes Ø82*47.5mm cutout 7mm UP-DL W-D 23V 5W K 4h 8 Yes Ø82*47.5mm cutout 7mm UP-DL W-D 23V 5W K 4h 8 Yes Ø82*47.5mm cutout 7mm UP-DL W-D 23V 5W K 4h 8 Yes Ø82*47.5mm cutout 7mm Operating Temp Operating Humidity Storage Temp 5W Ⅱ IP54-2 o C~45 o C ~9% -2 o C~65 o C

4 Spectral Distribution 3K 4K.8 Max=35 [1.=2] 5.92 SDCM F3K.8 Max=2869 [1.=2] 4.16 SDCM F4K x=.4518 y= x=.3885 y= K 57K.8 Max=3445 [1.=2] 4.3 SDCM F5K.8 Max=4431 [1.=2] 4.96 SDCM F57K x=.3533 y= x=.334 y= Photometric Diagram 3K 4K / MH=1m C/18 C9/27 Flux out: lm / MH=1m C/18 C9/27 Flux out: lm AVERAGE BEAM ANGLE(5%): 88.3 DEG Height Eavg, Emax Angle: 87.97deg Diameter AVERAGE BEAM ANGLE(5%): 88.3 DEG Height Eavg, Emax Angle: 88.14deg Diameter 5K 57K -/ AVERAGE BEAM ANGLE(5%): 88.7 DEG MH=1m 2.5 C/18 C9/ Flux out: lm Height Eavg, Emax Angle: 88.5deg Diameter -/ AVERAGE BEAM ANGLE(5%): 88.9 DEG MH=1m 2.5 C/18 C9/ Flux out: lm Height Eavg, Emax Angle: 88.35deg Diameter

5 Polar Diagram Comparison -15 O -/+18 O 15 O -12 O 12 O -9 O 9 O -6 O O -3 O 3 O O AVERAGE BEAM ANGLE (5%): 88.9 DEG C/18, 88.9 deg C3/21, 89.1 deg C6/24, 89. deg C9/27, 88.6 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%.4 Lifetime (hours) o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85% % 75% FLUX.1.5 U'V' 7% LifeTime (hours) Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C 7 6 IC Temperature ( o C) Capacitor MOS LED Fitting 1 Transformer Environmental temperature 14:34:57 14:46:53 14:58:53 15:1:53 15:22:53 15:34:53 15:46:53 15:58:53 16:1:53 Time 16:22:53 16:34:53 16:46:53 16:58:53 17:1:53 17:22:53 17:34:53 17:46:53 The driver lifespan is based on capacitor working temperature.

6 Installation Install requirements A-gap above the fitting B-gap to the building material C-gap to the thermal insulation 25mm 25mm 25mm 1. Open a hole according to the cutout size of led downlight. 2. Use screw-driver to open the driver terminal cover, feed the main AC wire L. N. in terminal block respectively, then fix the cover back. 3. Connect the downlight with driver, hold back the spring clip then push the downlight into the hole. 4. Make sure the downlight fixed tightly in ceiling, turn on the power (Fig 1). Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 43.5*33* '' standard container 4'' standard container CTNS Q'TY(PCS) VOLUME(CBM) Phone: Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China