3M Three-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series

Transcription

1 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Military (with M s 518 or N518 polarizing key) and center bump polarization Low profile Optional ejector latches Mounting holes for securing header to board Three wall shroud provides design flexibility Solder tail and wrap tail options Optional polarizing posts available Optional high temperature insulator suitable for no lead soldering operations High temperature option is suitable for reflow soldering using paste in hole techniques See the Regulatory Information ppendix (RI) in the RoHS compliance section of for compliance information Physical Electrical Date Modified: May 21, 2012 Insulator: Material: Glass Filled Polyester (PT) Glass Filled Polyester (PCT) - High Temp Option Flammability: UL 94V-0 Color: Gray (PT), lack (PCT) Contact: Material: Copper lloy Plating: Underplating: 100 μ [ 2.54 μm ] Nickel - Overall Wiping rea: 0 μ [ 0.76 μm ] Gold Solder Tails: 200 μ [ 5.08 μm ] Tin Lead or Matte Tin (See Ordering Information) Marking: M Logo, Part Identification Number and Orientation Triangle Sheet 1 of 5 Current Rating: 5.00, 1 Contact Powered.00, 6 Contacts Powered 1.75, ll Contacts Powered Rating Conditions: EI Method 2, 0 C maximum temperature rise, 20% derated. Reference appropriate M Product Specification for detailed current derating curves. Environmental Insulation Resistance: > Ω at 500 V DC Withstanding Voltage: 1000 V RMS at Sea Level Temperature Rating: -55 C to +105 C Process Rating: High Temp PCT insulator version: 260 C, per J-STD-020C, single pass PT insulator version: 191 C, maximum insulator temperature, solder wave process only Moisture Sensitivity Level: 1 (per J-STD-020C) High Temp. (PCT) versions only UL File No.: E M is a trademark of M Company

2 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series -X0XX Header without Latchs -X2XX Header with Short Ejector/Latch for M Sockets without Strain Relief -XXX Header with Long Ejector/Latch for M Sockets with Strain Relief.08 [2.0].424 ±.010 [ ].08 [2.0].57 ±.010 [ ].68 [17.].97 Ref [24.6] 1.07 Ref [27.2].7 Ref [9.4].46 Ref [11.7].025 ±.002 Sq Typ [ 0.64 ].0 [7.6].24 [6.1] REF. D E ±.010 F Typ.1. 2X O.100 SEE NOTE # POSITION #1 REF Section - (Straight) Position 1 Orientation Triangle Notch (See Table 1 & Note1) Notch (See Table 1).025 ±.002 Sq Typ [ 0.64 ].21 [5.].16 [4.1] Notch C (See Table 1 & Note 1) F Typ.100 Ref.24 [6.1].0 [7.6].68 [17.].5 [8.9].12 [.0].049 Ref Section - (Right ngle) E ± [0.51] 2X Ø.100 (See Note 2) C.197 [5.00].20 [5.1] Sheet 2 of 5 M is a trademark of M Company

3 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Table 1 Pin Qty M Part Number Dimensions C D Polarizing Notches (2.1) (28.07) (21.97) 0.71 (18.0) C (7.2) 1.05 (.15) (27.05) 0.91 (2.1) C (9.7) (5.69) (29.59) 1.01 (25.6) C (44.8) (40.77) 1.65 (4.67) 1.21 (0.7) C (52.4) (48.9) (42.29) 1.51 (8.) C (62.6) 2.05 (58.55) (52.45) 1.91 (48.5) C (70.2) (66.17) 2.65 (60.07) 2.21 (56.1) C (82.9).105 (78.87) (72.77) 2.71 (68.8) C (95.6).605 (91.57).65 (85.47).21 (81.5) C (100.7).805 (96.65).565 (90.55).41 (86.6) C Table 2 M Part Number Suffix Contact Tail Dimension E Pin Cross Section Dimension F Diagonals Corner Radii Dimension G -1XX2-2XX2 Solder Tail for.062 (1.57) Thick PC oard.112 (2.84).0245 ±.0005 (0.622).028 ±.001 (0.71).0075 Ref (0.191) 0.05 ±.00 (0.89) (See Note ) -1X0-2X0 Solder Tail for 0.94 (2.9) to.125 (.18) Thick PC oard.155 (.94).0245 ±.0005 (0.622).028 ±.001 (0.71).0075 Ref (0.191) 0.05 ±.00 (0.89).00 [7.62] Side to Side Stackability or Ø.116 [2.95] Ø.106 [2.69] (See Note 2) G Dim Ø.106 [2.69] or Ø.116 [2.95].41 (See Note 2) [10.4] Max to Edge of PC for Daisy Chain G Dim.060 [1.52].100 ±.00 Position ± [8.94] Recommended Mounting Hole Pattern (Straight).029 [0.74].100 ±.00 Position ± [5.89] Recommended Mounting Hole Pattern (Right ngle) C Notes: 1. Notches & C will accomodate M Polarizing Keys (M Part #518 or N518). 2. ccepts Rear and Front mounting hardware: Rear Entry: #4-24 thread cutting screw, M Part #41-5,.116 [2.95] dia mounting hole Front Entry: (Prior to installation of latch on Straight Versions) #2-56 bolt and nut, M Part #41-6,.106 [2.69] dia mounting hole. See illustrations on page 5.. The recommended PC hole size for the kinked tail positions on the.112 solder tail connector is.05 ±.002. Kink is located.05 below bottom surface of plastic. External radius of kink toward part centerline Inch (mm) Tolerance Unless Noted Inch ±.1 ±.01 ±.005 [ ] Dimensions for Reference only Sheet of 5 M is a trademark of M Company

4 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Ordering Information N = High Temp lack (PCT)/(R Plating Req d) lank = Std. Temp Gray (PT) /(lank or U Pltg. Req d.) Shroud and Pin Configuration 1 = Wall, Right ngle Solder Tail 2 = Wall, Straight Solder Tail XXXX - XXXX XX M Part Number (See Table 1) Latch/Ejector System 0 = No Latch/Ejector 2 = Short Roll PinLatch/Ejectors = Long Roll Pin Latch/Ejectors R = 0 μ Gold with Matte Tin Tails (pp. E1 & C1 pply) lank or U = 0 μ Gold with Sn/Pb Tails (pp. E & C2 pply) Tail 02 = Solder Tail for.062 [1.57] Thick oard K2= Kinked Solder Tails for.062 [1.57] Thick oard 0 = Solder Tails for.094 to.125 [2.9 to.18] Thick oard Part Customization This spec sheet details our standard offering. M has several capabilities that can provide a part tailored to your specific needs. sk your M sales representative or customer service for more details. Use of snap-in style latch/ejectors in either short (NXXX X5XX) or long (NXXX-X6XX) styles, installed or shipped separately (the -5 & -6 snap-in latches are dimensional and functional equivalents to the -2 & - roll pin latches) which are also available separately with roll pins included. Refer to chart below. If ordering snap-in or roll pin style latches separately, please use the below chart Standard Temperature (PT) High Temperature (PCT) High Temperature (PT) High Temperature (PP) Short Latch Long Latch Latch Style Color Roll Pin Gray N505-2 N505- Roll Pin lack Snap-In Gray N505-0 N505-1 Snap-In lack Selective pin removal (T or other compatability) Wire wrap tails styles Kinked Tail (K2 option) positions: 2500 & 000 Series Shrouded Header Total Number of Pins Number of Tails Kinked Positions Kinked Kinked Tail Detail: Kink is located.05 below bottom surface of plastic. External radius of kink toward part centerline. Sheet 4 of 5 M is a trademark of M Company

5 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Polarizing Post.21 [8.15] 201- P T G ra y L C P la c k.100 Dia Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude.115 [2.92] Polarizing Keys Dim N518 LCP lack PT Gray.02 reakaway Tab.15 [.8].4 Ref [8.6].09 [2.] Note: #2216 / Scotchweld can be used to adhere keys (Installed from bottom of board) Mounting Hardware 41-6 (Must be inserted prior to latch on vertical headers).1 [7.9].50 [12.7] Panhead Thread Cutting Screw: #4-24 X 5/16 Type: US Std T, Federal G 41-5 & 6 Material - Stainless Steel Hex Head olt, Nut and Washer olt - #2-56 X 1/2 Sheet 5 of 5 M is a trademark of M Company

6 Important Notice ll statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. efore using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. ny statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. M MKES NO OTHER WRRNTIES INCLUDING, UT NOT LIMITED TO, NY IMPLIED WRRNTY OF MERCHNTILITY OR FITNESS FOR PRTICULR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M Electronics Solutions Division 6801 River Place lvd. ustin, TX U.S Please recycle. Printed in US. M ll rights reserved. RI-2217-E M is a trademark of M Company.