Antistatic Compounds HI-TEMP MATERIAL ( C ) ( C ) 7.47 ( C ) C

Transcription

1 Conical side guides The conical guide rail incorporates two outstanding materials: stainless steel and UHMW. The stainless steel sheath provides rigid streamlined support for heavy loads at any speed, plus a solid connecting point for holding the rail in place with clamps and brackets. The UHMW guiding surface is available in a wide selection of shapes. The very low friction characteristics of UHMW allow containers to move at high speed with a minimum of drag, container damage, and noise. Materials are approved by the FDA and accepted for use in USDA inspected facilities. METAL PROFILE Metal profile is typically in stainless steel AISI 304 ( AISI 3 on the request), used for its excellent resistance to corrosion and long lasting attractive appearance. Galvanized steel can be ordered as an economical alternative to stainless steel. STANDARD VERSION Natural UHMW The manufacturing process allows the use of UHMW without additives or other processing chemicals. The result is a material that resists abrasion better, is more color stable (less prone to yellowing) and of uniform consistency. Available in two colors black and white. Zinc plated steel AISI 304 Polyethylene UHMW Low friction UHMW guiding surface SELF LUBRICATED VERSION NoluS UHMW Battleship grey color. A lubricant system is added to our standard UHMW during processing to give it reduced friction while maintaining all other physical properties. The coefficient of friction NoluS material is ca 35% lower as standard. The PVlimit for chain is at least 2 times the standard value for UHMW. NoluS VERSION WITH IMPROVED ELECTROSTATIC CONDUCTIVITY Static Dissipating UHMW Special formulation retains the low friction and wear characteristics of UHMW while effectively reducing problems caused by static. Color: black. Polyethylene UHMW Antistatic Specific electrical resistance (Ohm x cm) Metals Antistatic Polythylene Pure compressed Carbon black Conductive Compounds Antistatic Compounds Plastic Standard UHMW Static dissipative UHMW rail provides a conductive pathway to disperse the buildup of static electricity. VERSION FOR HIGH TEMRATURE High temperature. Special developed material to operate under high temperatures. The HT profiles are designed to operate under a continuous temperature of maximum 270 C.Typical applications for HT profiles are: Ovens, cookers, hot fill area, steam chambers, furnace discharge, retorts, fryers, shrink tunnels, pasturizers and steam boxes. For use in high temperatures SCIFICATIONS Tensile Strength ASTM D57 (N/mm 2 ) Deformation under load ASTM D621 (%) Coefficient of thermal expansion ASTM D69m/mm/ Cx10 5 ) Coefficient of friction ASTM D1894 Continuous service temperature HITEMP MATERIAL ( 37 0 C ).62 ( C ) 7.47 ( C ) C MATERIAL PROFILE 500 VERSION WITH NYLATRON INSERT For applications such as high conveyor speeds, heavy loads or abrasive conditions. Nylatron can be used at continuous temperatures up to 93 C. Nylatron

2 CONICAL SIDE GUIDES CONICAL SIDE GUIDES Material: Extruded ultra high molecular weight polyethylene. Max. continuous service temperature in air 90 C. Water absorption coefficient = 0. Sheath material see the table. Notes: These USDAapproved designs eliminate the chance of contamination by sealing out liquids and debris. As a result, they make it easy to maintain a clean, sanitary surface. Preferred type, readily available (codes marked in red) NoluS Accessories for bending machines AISI 304 Zinc plated steel Polyethylene UHMW STANDARD VERSIONS R7.5 R7 Standard version L 19019V 19019VL L 19020AS 19020ASL 19S005NS3M 19S005NS6M L 19021V 19021VL L VGSSRSD3M VGSSRSD6M VGSSRNS3M VGSSRNS6M as as NoluS NoluS Metal profile material SS 304 ZN Light Grey Light Grey Polyethylene antistatic UHMW Teflon alloy.5 SOLID VERSIONS Solid version 19S0063M 19S0066M VGSSRS3M VGSSRS6M SS 304 CONICAL SIDE GUIDES Weight: 0.60 Kg/m Packaging: eters STANDARD VERSIONS Standard version Metal profile material.5 R.50.5 R L L 19024AS 19024ASL 19S009NS3M 19S009NS6M L L VGSSMSD3M VGSSMSD6M VGSSMNS3M VGSSMNS6M as as NoluS NoluS SS 304 ZN Light Grey Light Grey.5.5 SOLID VERSIONS Solid version 19S001303M 19S001306M VGSSMS3M VGSSMS6M SS 304 CONICAL SIDE GUIDES Weight: 0.60 Kg/m Packaging: eters 76 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

3 CONICAL SIDE GUIDES STANDARD VERSIONS Standard version Metal profile material L L 19028AS 19028ASL 19S00115NS3M 19S00115NS6M 19S00115HT3M L L VGSSFSD3M VGSSFSD6M VGSSFNS3M VGSSFNS6M VGSSFHT3M as as NoluS NoluS HT SS 304 ZN Light Grey Light Grey.5 SOLID VERSIONS Solid version 19S0013M 19S0016M VGSSFS3M VGSSFS6M SS 304 CONICAL SIDE GUIDES Weight: 0.60 Kg/m Packaging: eters 25 Standard version Metal profile material.5 2 STANDARD VERSIONS Weight: 0.55 Kg/m Packaging: eters L L L L SS 304 ZN STANDARD VERSIONS Weight: 0.62 Kg/m Packaging: eters Standard version 19063W 19063WL L L L Metal profile material SS 304 ZN CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 77

4 CONICAL SIDE GUIDES 5 Standard version Metal profile material STANDARD VERSIONS Weight: 0.72 Kg/m Packaging: eters L L L L SS 304 ZN Standard version Metal profile material STANDARD VERSIONS Weight: 0.65 Kg/m Packaging: eters 19S001383M 19S001386M 19S00138SD3M 19S00138SD6M VGSSMT3M VGSSMT6M VGSSMTSD3M VGSSMTSD6M as as SS R Standard version Metal profile material 22.5 STANDARD VERSIONS Weight: 1.05 Kg/m Packaging: eters L L L L SS 304 ZN 8.5 Standard version Metal profile material = = STANDARD VERSIONS Weight: 0.62 Kg/m Packaging: eters L L L L SS 304 ZN 78 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

5 CONICAL SIDE GUIDES STANDARD VERSIONS Weight: 0.62 Kg/m Packaging: eters Standard version L L L Metal profile material SS 304 ZN 8.7 Standard version Metal profile material STANDARD VERSIONS Weight: 0.68 Kg/m Packaging: eters L L 19058AS 19058ASL 19S00153N3M L L VGSST.75SD3M VGSST.75SD6M VGSSTN.753M as as Nylatron SS 304 ZN STANDARD VERSIONS SOLID VERSIONS Standard version L L AS ASL 19S00187NS3M 19S00187NS6M L L Solid version 19S0043M 19S0046M VGSSWFSD3M VGSSWFSD6M VGSSWFNS3M VGSSWFNS6M VGSSWFS3M VGSSWFS6M as as NoluS NoluS Metal profile material SS 304 ZN SS 304 Light Grey Light Grey CONICAL SIDE GUIDES Weight: 0.72 Kg/m Packaging: eters CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 79

6 CONICAL SIDE GUIDES Preferred type, readily available (codes marked in red) STANDARD VERSIONS 8 Standard version Metal profile material L L 19032AS 19032ASL 19S00154N3M L L VGSST1.00SD3M VGSST1.00SD6M VGSSTN1.003M as as Nylatron SS 304 ZN CONICAL SIDE GUIDES Weight: 0.78 Kg/m Packaging: eters STANDARD VERSIONS Standard version L L L L Metal profile material SS 304 ZN Solid version 19S0053M 19S0056M VGSSWFS1.253M VGSSWFS1.256M SS 304 CONICAL SIDE GUIDES Weight: 0.76 Kg/m Packaging: eters SOLID VERSIONS STANDARD VERSIONS SOLID VERSIONS Standard version L L 19034AS 19034ASL 19S004NS3M 19S004NS6M 19S004N3M 19S004HT3M L L Solid version 19S0053M 19S0056M VGSST1.25SD3M VGSST1.25SD6M VGSST1.25NS3M VGSST1.25NS6M VGSSTN1.253M VGSSTHT1.253M VGSSTS1.253M VGSSTS1.256M Metal profile material as SS 304 as NoluS NoluS Nylatron HT ZN SS 304 Light Grey Light Grey CONICAL SIDE GUIDES Weight: 0.86 Kg/m Packaging: eters 80 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

7 CONICAL SIDE GUIDES Preferred type, readily available (codes marked in red) 21 CONICAL SIDE GUIDES Weight: 0.90 Kg/m Packaging: eters 8 40 Standard version L L 19060AS 19060ASL 19S006NS3M 19S006NS6M 19S006N3M L L VGSST1.60SD3M VGSST1.60SD6M VGSST1.60NS3M VGSST1.60NS6M VGSSTN1.603M as as NoluS NoluS Nylatron Metal profile material SS 304 ZN Light Grey Light Grey STANDARD VERSIONS Weight: 0.94 Kg/m Packaging: eters Standard version L L L L Metal profile material SS 304 ZN STANDARD VERSIONS Weight: 0.95 Kg/m Packaging: eters Standard version L L 19039AS 19039ASL L L VGSST1.70SD3M VGSST1.70SD6M as as Metal profile material SS 304 ZN CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 81

8 CONICAL SIDE GUIDES 21 Standard version Metal profile material STANDARD VERSIONS Weight: 1.1 Kg/m Packaging: eters L L AS ASL 19S007NS3M 19S007NS6M L L VGSST2.25SD3M VGSST2.25SD6M VGSST2.25NS3M VGSST2.25NS6M as as NoluS NoluS SS 304 ZN Light Grey Light Grey STANDARD VERSIONS Weight: 0.72 Kg/m Packaging: eters Standard version L L L L Metal profile material SS 304 ZN STANDARD VERSIONS Weight: 0.15 Kg/m Packaging: eters Standard version L L L L Use: wear strip and side guide for modular wide belts Metal profile material SS 304 ZN STANDARD VERSIONS Weight: 1.15 Kg/m Packaging: eters Standard version L L 19S003NS3M 19S003NS6M L L VGSSLT1.0X38NS3M VGSSLT1.0X38NS6M Use: wear strip and side guide for modular wide belts NoluS NoluS Metal profile material SS 304 ZN Light Grey Light Grey 82 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

9 CONICAL SIDE GUIDES Standard version Metal profile material STANDARD VERSIONS Weight: 0.80 Kg/m Packaging: eters L L L L Use: ISO B1 European series roller chains SS 304 ZN STANDARD VERSIONS Weight: 1.2 Kg/m Packaging: eters Standard version 19S001813M 19S0018M 19S00181B3M 19S00181B6M VGSSTG023M VGSSTG026M VGSSTG02B3M VGSSTG02B6M Metal profile material SS Standard version Metal profile material 19S00182NS3M VGSSUT1.00S3M NoluS SS 304 Light Grey STANDARD VERSIONS Weight: 1.3 Kg/m Packaging: eters Standard version Metal profile material STANDARD VERSIONS Weight: 1.5 Kg/m Packaging: eters 19S00183NS3M VGSSUT1.30S3M NoluS SS 304 Light Grey CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 83

10 POLYGLIDE TM POLYGLIDE TM Guide rail for use with plastics such as T and polypropylene. PolyGlide TM rail is designed to be an economical solution to guiding plastic containers, cartons, and conveyor belting. PolyGlide TM is constructed using 304 stainless steel as the guide contact surface and can be used with all standard Valu Guide rail clips and clamps. PolyGlide reduces static buildup. Plastic packaging and T bottles can generate high levels of static buildup as they travel along a conveyor. PolyGlide provides static buildup with a pathway to the surrounding conveyor frame where it can dissipate. Conveyor frame may need to be grounded. PolyGlide can be used in higher operating temperatures. PolyGlide can withstand harsh environments such as: Steam chambers, furnace discharge, steam boxes, shrink tunnels, pasteurizers, hot fill area, ovens, cookers, fryers. AISI 304 For use in high temperatures Saves time and money Static charge reducing capability for bending machines 13.7 POLYGLIDE PROFILE 19S000083M 19S000086M VGSPM3M VGSPM6M 60 m SS The design of the stainless steel profile, used in the Valu Guide combines the strength of a round solid bar with a diameter of more than mm with a smoothly curved sliding surface with a radius of over 50mm. R>50 < 84 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

11 POLYGLIDE TM AISI 304 Saves time and money For use in high temperatures Static charge reducing capability POLYGLIDE PROFILE 13S00092 VGPMI25 n 20 T Thermoplastic elastomers Accessories PATENTED Par. # 6,105,757 (USA) POLYGLIDE PROFILE 13S00093 VGPMI30 n 20 SS S S00008 PATENTED Par. # 6,053,654 (USA) S S S S CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 85

12 ADJUSTABLE GUIDE RAIL CLAMP Preferred type, readily available (codes marked in red) See page 2 Polyamide See page 76 Open position for conical side guides max 35 4ax Closed position for conical side guides 200 JOINT ROD ADAPTER (page 2) clamp closed clamp open large containers small containers Material: clamp in PA, bolts in stainless steel nuts in nickel plated brass. Supply: assembled For profiles S005NS 19S CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

13 STRAIGHT NECK GUIDE RAILS Preferred type, readily available (codes marked in red) Polyethylene UHMW On request straight neck guide rais with special dimensions can be produced. For further information contact our Engineering Department STRAIGHT NECK GUIDE RAILS Material: Ultra High Molecular Weight Polyethylene to provide minimum friction and reliable long term performance. Note: max. continuous service temperature in air 90 C. Water absorption coefficient = 0. Colour: green. Supply: 2,52 or eters. Packaging: 10 pieces (25.2 or eters). Use: overhead transport of T bottles. R L R L 2.52 m 25 m CORNER NECK GUIDE RAILS CORNER NECK GUIDES RAILS Material: Ultra High Molecular Weight Polyethylene to provide minimum friction and reliable long term performance. Note: max. continuous service temperature in air 90 C. Water absorption coefficient = 0. Colour: green. Supply: corner tracks are supplied complete. Use: overhead transport of T bottles. RE Rm RI 32 L R Rm Rm RE RE RI RI Corner neck guide rails L = 28.5 L L Corner neck guide rails L = R Corner neck guide rails L = 42 Rm RE RI L CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 87

14 NECK GUIDES FOR T CONTAINERS NECK GUIDES Helps guide T and HD containers in high speed, air conveying applications. NoluSR is a proprietary alloy of reinforced UHMW and other USDA accepted lubricants, resulting in a harder, lower friction material that is ideal in these applications. Though design differ, the material of choice is NoluSR, proven to increase throughput, reduce jams and wear longer. Material: NoluSR is a special UHMW with modified molecular structure helps guide T containers in high speed applications. NoluS NoluSR Preferred type, readily available (codes marked in red) Also available in antistatic! R 1.2 R S00036NS30M 19S00036NS75M 19S00036NSR30M 19S00036NSR75M VGP105R30M VGP105R75M VGP105RCL30M VGP105RCL75M 75 m 75 m 75 m 75 m NoluS NoluS NoluSR NoluSR Light Grey Light Grey Dark Grey Dark Grey S00040NSR30M 19S00040NSR75M VGNG47SR30M VGNG47SR75M 75 m 75 m NoluSR Dark Grey S00041NSR30M 19S00041NSR75M VGNG49SR30M VGNG49SR75M 75 m 75 m NoluSR Dark Grey S00042NSR30M 19S00042NSR75M VGNG50SR30M VGNG50SR75M 75 m 75 m NoluSR Dark Grey 88 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

15 NECK GUIDES FOR T CONTAINERS S00043NSR75M VGNG81SR75M 75 m 75 m NoluSR Dark Grey S00038NSR30M VGNG91SR30M NoluSR Dark Grey S00039NSR30M VGNG110SR30M NoluSR Dark Grey S00037NSR30M VGNG5SR30M NoluSR Dark Grey 986 M NECK GUIDE CURVE 19S00044NSR VGNG5SR1M28 n 1+1 NoluSR Dark Grey CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 89

16 GUIDES FOR T BOTTLES GUIDES FOR T BOTTLES Aluminum guide rail with Nolus insert is used to guide containers, especially T and HD, in application such as air conveying. Many air conveyor users and manufacturers have found that brush guides tend to get contaminated with debris, which causes increased friction and marking of T bottles. NoluS is the perfect combination of extremely low friction in a tough UHMW based material. NoluS will not mark bottles while allowing faster speeds and greater throughput. NoluS Aluminium 19S for bending machines Preferred type, readily available (codes marked in red) N Accessories Low friction, nonmarking! More sanitary N 20 19S000093M 19S000096M VGABG3M VGABG6M 60 m AL Reduced Splices! S00079NS30M VGPBG7NS30M NoluS Light Grey S00079NSD30M VGPBG7NSD30M NoluS antistatic NoluS antistatic 90 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

17 GUIDES FOR T BOTTLES NoluS antistatic NoluS Aluminium for bending machines Accessories NOLUS NoluSR neck guides and NoluS body guides, with an ultra low coefficient of friction, reduces the degree of bottle tilt and the corresponding wear problems. OTHER GUIDES Other guides (especially brushes), when contaminated, can cause irregular tilt and orientation of the bottles, resulting in blockage at curves or inclines. Low friction, nonmarking! More sanitary Aluminium L m Aluminium Reduced Splices! S00078NS30M 19S00078NSD30M VGPBG5NS30M VGPBG5NSD30M NoluS NoluS antistatic Light Grey CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 91

18 PRODUCT GUIDES GUIDE RAILS Material: Metal profile in anodized aluminium. Extruded profile in UHMW. Characteristics: Very low friction coefficient. High resistance to chemical agents. Notes: Aluminium profile and plastic profile are supplied assembled. Application: as side guides for air conveyor and standard conveyor. Polyethylene UHMW Anodized aluminium Accessories for bending machines Aluminium L m Aluminium 13.6 EXTRUDED PROFILE 19068N 19068NA 19068P W m 60 m Antistatic Yellow Orange 4 15 R2 R2 ASSEMBLED GUIDE RAILS N NL Other assemblies of aluminium and extruded profiles can be made on request and for adequate quantities. 92 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

19 PRODUCT GUIDES GUIDE RAIL Material: Metal profile in anodized aluminium. Brushes profile in natural fibres. Characteristics: Very low friction coefficient. Supply: eter. Aluminium profile and brushes profile are supplied assembled. Application: as side guides for air conveyor. Polyethylene UHMW Brushes Anodized aluminium Accessories for bending machines Aluminium Aluminium BRUSHES PROFILE ASSEMBLED GUIDE RAILS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 93

20 ALUMINIUM GUIDE RAIL Anodized Aluminium Aluminium Polyethylene UHMW M for bending machines S002103M 19S002106M VGA2253M VGA2256M Al S0023M 19S0026M 19S0023M 19S0026M VGA6003M VGA6006M VGA600A3M VGA600A6M 60 m 60 m Al Al Ala Ala S000253M 19S000256M 19S M VGP8133M VGP8136M VGP81330M 60 m S000263M 19S000266M 19S M VGP813F3M VGP813F6M VGP813F30M 60 m S000323M VGP08083M S000333M VGP6113M CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

21 ALUMINIUM GUIDE RAIL S000343M 19S000346M VGP8F3M VGP8F6M 60 m S000313M 19S0003M VGP820F3M VGP820F6M 60 m S000273M 19S000276M VGP822F3M VGP822F6M 60 m S000223M 19S000226M VGP824F3M VGP824F6M 60 m S000283M 19S000286M VGP834F3M VGP834F6M 60 m 6.5 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 95

22 ALUMINIUM GUIDE RAIL Aluminium Polyethylene UHMW M8 19S S for bending machines S002093M 19S002096M VGA3503M VGA3506M 60 m AL S002243M 19S002246M VGP3503M VGP3506M 60 m Aluminium Polyethylene UHMW M for bending machines S002113M 19S0021M VGA25203M VGA25206M 60 m AL S002263M 19S002266M VGP2520BC3M VGP2520BC6M 60 m CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

23 PRODUCT GUIDES STANDARD GUIDE RAILS Material: Metal profile, see the table. Plastic profile in UHMW. Characteristics: Very low friction coefficient. Moderate resistance to chemical agents. No liquid absorption. Supply: 3 or eters. AISI Accessories Polyethylene UHMW Zinc plated steel METAL PROFILE L L S/S AISI 304 Zinc plated steel R10 15 EXTRUDED PROFILE L L R STANDARD GUIDE RAILS Notes: the metal profile and plastic profile are supplied assembled L L L L Metal profile material S/S 304 Zinc plated steel CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 97

24 PRODUCT GUIDES GUIDE RAILS Material: Metal profile, see the table. Plastic profile in UHMW. Characteristics: Very low friction coefficient. High resistance to chemical agents. No liquid absorption. Supply: 3 or eters. Steel profile and plastic profile are supplied assembled. Polyethylene UHMW AISI Accessories Polyethylene antistatic UHMW AISI for bending machines C KC 19048K S/S 304 S/S 430 These profiles are applicable to code C cod METAL PROFILE C NS 19070C BC 19070B 19071ASC 19071AS 0.20 NoluS a a Grey EXTRUDED PROFILE GUIDE RAILS Notes: the steel profile and wear strip are supplied assembled NC 19063N 19063VC 19063V 19063BC 19063B 19063ASC 19063AS 19063KNC 19063KN 19063KVC 19063KV 19063KBC 19063KB 19063KASC 19063KAS Plastic profile material a a a a Metal profile material S/S 304 S/S CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

25 PRODUCT GUIDES GUIDE RAILS Material: Metal profile in anodized aluminium. Plastic profile in UHMW. Characteristics: Very low friction coefficient. High resistance to chemical agents. No liquid absorption. Supply: 3 or eters. Metal profile and guide rails are supplied assembled. Polyethylene UHMW Anodized aluminium Polyethylene antistatic UHMW 28 Accessories for bending machines L Ala These profiles are applicable to code L cod ALUMINIUM PROFILE C NS 19070C BC 19070B 19071ASC 19071AS 0.20 NoluS a a Grey EXTRUDED PROFILE GUIDE RAILS Supply: 3 or eters. Packaging: eters. Notes: the aluminium profile and guide rails are supplied assembled N 19098NL 19098V 19098VL 19098B 19098BL 19098AS 19098ASL 0.70 Plastic profile material a a Metal profile material ALa CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 99

26 PRODUCT GUIDES GUIDE RAILS (Flat type) Material: Polyethylene Characteristics: They can be bent or calendered by means of usual systems or using bending machines code or Coefficient of linear expansion: 2.5 x Temperature range for continuous use in air: 35 C +70 C. Min. bending radius: 200 mm. Notes: when sealing the ends a 2 mm space must be left between the silicone and the end of the bar to compensate for linear contraction of the guide rail at low temparatures. Polyethylene Accessories for bending machines FLAT GUIDE Characteristics: To use this guide, a 30x5 mm steel bar should be inserted 19098L SIDE GUIDE Characteristics: To use this guide, a 60xm steel bar or double MProfile should be inserted L BL 19082B 19082VL 19082V Light blue Light blue SIDE GUIDE Characteristics: To use this guide, a 60xm steel bar or double MProfile should be inserted L AL 19050A 19050VL 19050V Light blue Light blue CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

27 PRODUCT GUIDES GUIDE RAILS Material: Extruded ultra high molecular weight polyethylene. Max. continuous service temperature in air 90 C. Water absorption coefficient = for bending machines 104 Accessories Polyethylene UHMW NoluS A B C D E SIDE GUIDES 19054N 19054NL 19054V 19054VL 19080N 19080NL 19080V 19080VL 19053N 19053NL 19053V 19053VL 19081N 19081NL 19081V 19081VL 19052N 19052NL 19052V 19052VL 19052NS 19092N 19092NL 19092V 19092VL NoluS Grey 20 E 6 6 F SIDE GUIDE FOR LABELLING BOTTLE A B D C H G 19085N 19085V 19086N 19086V 19087N 19087V 19088N 19088V 19089N 19089V A B C D E F G H m 2 m 2 m 2 m 2 m CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 101

28 PRODUCT GUIDES 104 GUIDE RAILS Material: Extruded ultra high molecular weight polyethylene. Max. continuous service temperature in air 90 C. Water absorption coefficient = 0. Polyethylene UHMW Accessories R R6 R6 SIDE GUIDE V SIDE GUIDE V CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

29 PRODUCT GUIDES GUIDE RAILS Material: Round profile in stainless steel AISI 303. Plastic profile in UHMW. Polyethylene UHMW 3 9 Accessories for bending machines A B SIDE GUIDE B B B A B C C ROUND PROFILE Ød Ø d 8 10 SS 303 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 103

30 ACCESSORIES FOR GUIDE RAILS Accessories AISI for bending machines A MPROFILE L L L A SS A MPROFILE L A SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

31 BENDING MACHINES AND BENDING ROLLERS MOTORIZED BENDING MACHINE Technical features: Millimeter and decimal reading for pressing roller adjustment. Tempered shafts mounted on double supports and rotating on opposing tapered roller bearings. Hardened and tempered sliding blocks located on the machine casing. Shaft diameter 25 mm. Main motor V Hz. Approximate weight 100 Kg SB MANUAL BENDING MACHINE Technical features: Millimeter and decimal reading for pressing roller adjustment. Tempered shafts mounted on double supports and rotating on opposing tapeered roller bearings. Hardened and tempered sliding blocks located on the machine casing. Shaft diameter 25 mm. Approximate weight 35 Kg. IMPORTANT: the bending machines are supplied without rollers, these must be ordered separately according to the guide rail type (see table). Series of bending rollers METHOD OF BENDING 1 Select the rollers designed specifically to bend the style rail desired and assemble to the machine. 2 Determine the radial length of the desired curve and mark the rail to show the beginning and end of the curve. 3 Center the portion of the rail in the machine and snug up the center wheel. Turn the crank 1 to 2 turns and rotate the gear box handle until the mark at one end is slightly past the contact point of the center wheel. Repeat this at the other end. 4 Repeat Step 3. 5 Center the turn section in the machine again and turn the center wheel crank inward a maximum of 2 turns. Rotate the gear box handle, this time until each mark reaches the contact of the center wheel. 6 Repeat Step 5 until the desired curve is completed. R R CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 105

32 ROLLERS FOR BENDING MACHINE Preferred type, readily available (codes marked in red) R Internal curve R External curve Types of guides to be bent No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

33 ROLLERS FOR BENDING MACHINE Preferred type, readily available (codes marked in red) R Internal curve R External curve Types of guides to be bent No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers No. of rollers CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 107

34 ROLLERS FOR BENDING MACHINE Preferred type, readily available (codes marked in red) R Internal curve R External curve Types of guides to be bent No. of rollers R.min=305 R.min=305 S00001 No. of rollers R.min=305 R.min=305 S00100 No. of rollers R.min=305 R.min=305 S00200 S00050 No. of rollers R.min=762 R.min=762 19S00009 No. of rollers R.min=762 R.min=762 19S00007 No. of rollers R.min=762 R.min= No. of rollers R.min=457 R.min=457 19S CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

35 ROLLERS FOR BENDING MACHINE Preferred type, readily available (codes marked in red) R Internal curve R External curve Types of guides to be bent No. of rollers R.min=457 R.min=457 19S00182 No. of rollers R.min=457 R.min=457 19S00035 No. of rollers R.min=559 R.min=559 19S00083 No. of rollers R.min=102 R.min=102 19S00008 No. of rollers S S002 19S00209 R.min=152 R.min=152 No. of rollers R.min= R.min=203 19S00211 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 109

36 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled NV Ø A 10 Ø B 13.5 Type 1 2 SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled Clamp type DP 110 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

37 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled DP CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 111

38 GUIDE RAIL CLAMPS SINGLE CLAMP WITH ROD Nickel plated brass AISI 303 Reinforced polyamide Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled. See pages See pages See page for rod design Preferred type, readily available (codes marked in red) 13S00250 PATENTED Par. # 5,626,221 (USA) Ø.7 13S00250 VG mm n Ø.7 13S00251 VG mm n Ø.7 13S00252 VG mm n 10 1 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

39 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design SINGLE CLAMP WITH BOLT Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled DP CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 113

40 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design ADJUSTABLE GUIDE RAIL CLAMP Material: clamp in reinforced polyamide, bolts in stainless steel, nut in nickel plated brass. Supply: assembled. Use: mount on 25x6 flat bar or Ø diameter rod ADJUSTABLE GUIDE RAIL CLAMP Par. # 6,685,385 (USA) Material: clamp in reinforced polyamide, bolts in stainless steel, nut in nickel plated brass. Supply: assembled. Use: mount on 25x6 flat bar or Ø diameter rod. 13S00346 with special threaded insert VG02201M ADJUSTABLE GUIDE RAIL CLAMP Material: clamp in reinforced polyamide, bolts in stainless steel, nut in nickel plated brass. Supply: assembled. Use: mount on 25x8 flat bar CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

41 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design ADJUSTABLE GUIDE RAIL CLAMP Material: clamp in reinforced polyamide, bolts in stainless steel, nut in nickel plated brass. Supply: assembled. Use: mount on 25x8 flat bar x8 M ADJUSTABLE GUIDE RAIL CLAMP M8 Material: clamp in reinforced polyamide, bolts in stainless steel, nut in nickel plated brass. Supply: assembled. Use: mount on 25x10 flat bar x10 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 115

42 CLAMPS FOR CONICAL SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See page for rod design.5 SINGLE CLAMP Ø8 Use: it connects guide rail to bracket or rod using a standard M8 cap screw SWIVEL CLAMP Material: reinforced polyamide. nut, washer and rod in stainless steel. Supply: assembled. Note: code 137 is supplied without rod. APPLICATION EXAMPLE ØDP PAFG This design allows a maw. swivel angle of DP 1 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

43 CLAMPS FOR CONICAL SIDE GUIDES Preferred type, readily available (codes marked in red) Nickel plated brass AISI 303 Reinforced polyamide See pages DOUBLE CLAMP WITH ROD Material: reinforced polyamide, nut, washer rod in stainless steel. Supply: assembled. 13S S S S00503 VG01101PM10 VG01101P VG01101P VG01101P DP 10 n 10 See page 182 See pages for rod design DOUBLE CLAMP WITH ROD Material: reinforced polyamide, nut, washer rod in stainless steel. Supply: assembled. Note: code 13008NV is supplied without rod NV 13009NV 13010NV 13011NV DP CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 1

44 PRODUCTION CLAMPS FOR CONICAL PROGRAMSIDE GUIDES AND FOR ROUND GUIDE RAILS Preferred type, readily available (codes marked in red) See page 103 Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See pages for rod design DOUBLE CLAMP Material: reinforced polyamide, nut, washer and rod in stainless steel. s are supplied without rod and nut. Application: the clamp is designed to be used with either the conical or Ø mm round guide rails, simply by turning the internal flange plate. Use: to support rods or conical guide rails with increased centers. Supply: assembled. M10 Flange position for assembling Ø mm rod Rotate center piece 90 M10 Flange position for assembling conical side guide I I L A B Ø DP 118 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

45 CLAMPS FOR CONICAL SIDE GUIDES AND FOR ROUND GUIDE RAILS See page 103 Nickel plated brass AISI 303 Reinforced polyamide See pages See pages See pages for rod design DOUBLE CLAMP Material: reinforced polyamide, screw, washer and rod in stainless steel. s 135F 13351F 133F are supplied without rod and screw. Application: the clamp is designed to be used with either the conical or Ø mm round guide rails, simply by turning the internal flange plate. Use: to support rods or conical guide rails with increased centers. Supply: assembled. Flange position for assembling Ø mm rod Rotate center piece 90 Flange position for assembling conical side guide I I L A B Ø DP 135F 136F F 138F 13351F 13352F F 13354F 133F 134F F 136F CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 119

46 S S CLAMPS FOR CONICAL SIDE GUIDES L L 13 See pages AISI SINGLE RAIL CLAMP Thickness: S = 2 mm. Use: to support conical guide. Note: round hole version accepts a M8 bolt and square hole version accepts a M8 carriage bolt. Available in two lengths 38.1 mm wide and 76.2 mm wide for splicing. Tightening bolt not included. Sq. Ø S 130L 130SL VG001 VG0SH VG003 VG003SH L mm Ø Sq. 9 9 SS 304 L L 13 DOUBLE RAIL CLAMP Thickness: S = 2.5 mm. Use: to support conical guide. Note: round hole version accepts a M8 bolt and square hole version accepts a M8 carriage bolt. Available in two lengths 38.1 mm wide and 76.2 mm wide for splicing. Tightening bolt not included. Sq. Ø A C S S S L mm 38.1 A mm C mm Ø Sq SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

47 CLAMPS FOR CONICAL SIDE GUIDES L L 13 S See pages AISI Sq. Ø 63.5 TRIPLE RAIL CLAMP Material: stainless steel AISI 304, Thickness: S = 2.5 mm. Note: used with toll containers or when large and small containers run on the same production line. Tightening bolt not included S L mm Ø 10.5 Sq. 9 SS 304 fixed rail sliding rail 304 Par. # 6,053,654 (USA) PATENTED ADJUSTABLE SPLICING CLAMP Allows one rail to slide within the clamp while the other remains fixed. 13S00392 VG113SM08G 20m n 2 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 1

48 CLAMP FOR CONICAL SIDE GUIDES S L AISI 304 K.5 See pages HEAVY DUTY CLIP Material: stainless steel AISI 304, thickness S = 2.5 mm. Use: two piece compression style for easy assembly and adjustment. Nut and washer not included. Note: max recommended tightening torque 2.0 Kgm d VG018M01 VG018M02 VG018M03 VG018M04 L mm 26 K mm d thread size M8 n 100 S L SINGLE CLAMP Material: stainless steel AISI 304, thickness S = 2.5 mm. Use: easy assembly of guide profiles. Note: max recommended. tightening torque 1.8 Kgm M L 20 mm Light duty n 100 AISI AISI 304 S 11.5 L. CONNECTING ELEMENT Material: stainless steel AISI 304, thickness S = 2.5 mm. Use: to connect two guide rails. The part can be tapped on with a hammer L 38 mm 50 mm 2 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

49 CLAMP FOR CONICAL SIDE GUIDES AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel nut in nickel plated brass. Supply: assembled For guide Ø 8 10 AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design DP For guide Ø SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 3

50 CLAMPS FOR ROUND PROFILE GUIDES AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel nut in nickel plated brass. Supply: assembled For guide Ø 8 10 AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled DP For guide Ø CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

51 M6 Ex for Ø8 CLAMPS FOR ROUND PROFILE GUIDES AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt and rod in stainless steel nut in nickel plated brass. Supply: assembled. Note: code is supplied without rod DP AISI 304 Reinforced polyamide Consult see page 103 for roud profile CLIPON SINGLE CLAMP Material: clamp in polyamide, bolt stainless steel Use: with round profile guide Ø8 mm. Supply: assembled n 100 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 5

52 CLAMPS FOR ROUND PROFILE GUIDES AISI 303 Reinforced polyamide 58 for Ø Consult see page 103 for roud profile for rod design M5 26 M6 25x25 25 SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut and threaded bushing in nickel plated brass. Use: with round profile guide Ø mm. Supply: assembled AISI 304 Reinforced polyamide L Ø 103 H h1 Consult see page 103 for roud profile Accessories 26 M8 Range extension Y K 8.5 # 25x8 ADJUSTABLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled. Ø L K Y H h NV CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

53 CLAMPS FOR ROUND PROFILE GUIDES M D.P. for Ø AISI 303 Reinforced polyamide Consult see page 103 for roud profile for rod design for Ø DOUBLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt nut and rod in stainless steel. Supply: assembled. Note: code is supplied without rod DP _ PATENTED Ø Par. # 5,626,221 (USA) 13S00253 VG mm n Ø.7 mm 29 SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: assembled. 13S00254 VG mm n 10 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 7

54 CLAMPS FOR ROUND PROFILE GUIDES AISI A ø Reinforced polyamide Ex. Consult see page 103 for round profile A for rod design 13761XP DOUBLE CLAMP WITH ROD Material: clamp in reinforced polyamide, nut and rod in stainless steel. Supply: assembled. Note: code 13761XP is supplied without rod XP 13772XP 13773XP DP 8 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

55 CLAMPS FOR ROUND PROFILE GUIDES Ø10 Ø8 94 AISI DP 63.5 Reinforced polyamide DOUBLE CLAMP FOR ROUND PROFILE GUIDES Ø 810 mm Material: clamp in reinforced polyamide bolt, nut and rod in stainless steel. Note: code is supplied without rod. Use: round profile guides (8 or 10 mm) can be used simply turning the flange position DP 23 Consult see page 103 for round profile Flange position for assembling guides with diam. d = 8 mm. Flange position for assembling guides with diam. d = 10 mm for rod design Application example Ø Ø10 DOUBLE CLAMP FOR ROUND PROFILE GUIDES Ø 10 mm Material: clamp in reinforced polyamide bolt, nut and rod in stainless steel AISI 304 Note: code is supplied without rod. Use: round profile guides (10 or mm) can be used simply turning the flange position DP Flange position for assembling guides with diam. d = 10 mm Flange position for assembling guides with diam. = mm Application example Ø Ø CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 9

56 CLAMPS FOR STANDARD SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See page for rod design SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled n 100 SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: unassembled DP SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled n CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

57 CLAMPS FOR STANDARD SIDE GUIDES Nickel plated brass AISI 303 Reinforced polyamide See page for rod design SINGLE CLAMP WITH ROD Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass, rod in stainless steel AISI 303. Supply: unassembled DP ADJUSTABLE SINGLE CLAMP Material: clamp in reinforced polyamide, bolt in stainless steel, nut in nickel plated brass. Supply: assembled DOUBLE CLAMP WITH ROD Material: clamp in reinforced polyamide, nut and rod in stainless steel. Note: code is supplied without rod. Supply: unassembled DP CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 131

58 ACCESSORIES FOR FLAT SIDE GUIDES Reinforced polyamide See page 100 ENDPLUG Use: with flat side guide code L CONNECTING PLUG Use: with flat side guide code L n 10 PAFG n 10 PAFG ENDPLUG Use: with flat side guide code L n 10 PAFG 132 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

59 CLAMPS FOR FLAT SIDE GUIDE See page AISI for rod design Ø9 22 Ø9 15 FIXING CLAMP Thickness: S = m. Surface: tumbling finish. Use: with flat side guide code L Note: the clamp is supplied without rod and bolt. Supply: unassembled SS Ø 34 FIXING CLAMP WITH ROD Material: clamp, rod, screw and washer in stainless steel. Thickness: S = m. Surface: tumbling finish. Use: with flat side guide code L Supply: unassembled Rod Ø CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 133

60 ACCESSORIES FOR SIDE GUIDE (LARGE TY) AISI 304 Reinforced polyamide See page for rod design ENDPLUG Use: with side guide rails code L n 10 PAFG R1 PLUG Use: with side guide code L n 10 PAFG Ø4.5 COMBINERCLAMP Material: clamp and screws in stainless steel AISI 304. Thickness: S = 1.5 mm. Surface: scoch brite finish. Use: with side guide code L *Packaging: 10 pieces, complete with fixing screws L L n 10* SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

61 CLAMPS FOR SIDE GUIDE (LARGE TY) Preferred type, readily available (codes marked in red) Reinforced polyamide AISI 304 FIXING CLAMP One piece Material: clamp, washer and rod in stainless steel AISI 304. Thickness: S = 1.5 mm. Surface: scoch brite finish. Note: code 131 is supplied without rod. Supply: unassembled SS 304 See page for rod design 90 Ø FIXING CLAMP Material: clamp in reinforced polyamide, bolt and rod in stainless steel FIXING CLAMP Two pieces Material: clamp, screws, washer and rod in stainless steel AISI 304. Thickness: S = m. Surface: tumbling finish. Note: code is supplied without rod. Supply: unassembled SS 304 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 135

62 ACCESSORIES FOR SIDE GUIDES (EXTRA LARGE TY) AISI 304 Reinforced polyamide See page for rod design 8.5 ENDPLUG Material: reinforced polyamide. Use: with extra side guide code L Packaging: 10 pieces n 10 PAFG COMBINERPLUG Use: with extra side guide code L n 10 PAFG Ø COMBINERCLAMP Material: clamp and screws in stainless steel AISI 304. Thickness: S = 1.5 mm. Surface: scoch brite finish. Use: with extra side guide code L *Packaging: 10 pieces, complete with fixing screws L L n 10* SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

63 CLAMPS FOR SIDE GUIDE (EXTRA LARGE TY) AISI 304 Reinforced polyamide M6 63 See page for rod design 96 ØDP CLAMPS Material: clamp in reinforced polyamide, bolt and rod in stainless steel. Supply: unassembled. Note: code is supplied without rod Ø DP Ø FIXING CLAMP Thickness: S = 2 mm. Surface: tumbling finish. Use: with extra side guide code L. Note: code is supplied without rod and bolt. Supply: unassembled SS 304 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 137

64 ADJUSTING RODS AISI 303 ADJUSTING RODS Ø 4 Use: with code L Ø SS 303 ADJUSTING RODS Use: with code Ø 10 6 L Ø Ø SS 303 SS 303 Ø SCREW M ADJUSTING RODS Use: with code L Ø 32.5 Ø SS 303 ADJUSTING RODS Use: with code Ø 3 L Ø Ø SS 303 SS 303 SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

65 ADJUSTING RODS AISI Ø SCREW M ADJUSTING RODS Use: with code L Ø9.5 Ø SS 303 ADJUSTING RODS Use: with code13006nv Ø 3 10 L Ø11.5 Ø SS 303 SS 303 ADJUSTING RODS Use: with code Ø L 20 M SS 303 SS 303 SS 303 ADJUSTING RODS Ø 20 L M SS 303 SS 303 SS 303 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 139

66 ADJUSTING RODS ADJUSTING RODS Use: with code 13008NV NV Ø L 19 M SS 303 SS 303 SS 303 ADJUSTING RODS Use: with code Ø 25 L M SS 303 SS 303 SS 303 ADJUSTING RODS Use: with code 131. Ø L M SS 303 SS 303 SS 303 ADJUSTING RODS Use: with code 137. Ø 7 L Ø SS 303 SS 303 SS CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved

67 ADJUSTING RODS ADJUSTING RODS Use: with code Ø L Ø SS 303 SS 303 SS 303 ADJUSTING RODS Ø L SS 303 SS 303 SS 303 SS 303 ADJUSTING RODS Use: with code F Ø 26 L. 4 M SS 303 SS 303 CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved 1

68 JOINT ROD ADAPTER AISI Ø Ø19 13S S S00261 VG222JQM8 VG222JQM10 VG222JQM8MM10F M8 M10 M8 M8 M10 M10 n 10 SS 304 Pins must be parallel Large containers Small containers Pins must be parallel Loosen the brackets knob, slide the pins into position, then retighten the bracket knobs. BRACKET SPACERS FOR ROD USE Spacers may be required for proper set back of the brackets to allow for the jointed adjusting rod clevis extension. For details on spacers to pages CONVEYOR COMPONENTS Issue 18.0 System Plast S.r.l., All Rights Reserved