SOUTH AFRICAN QUALIFICATIONS AUTHORITY REGISTERED UNIT STANDARD: Inspect and test a single phase domestic installation UNIT STANDARD TITLE

Transcription

1 SAQA US ID All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source. SOUTH AFRICAN QUALIFICATIONS AUTHORITY REGISTERED UNIT STANDARD: Inspect and test a single phase domestic installation UNIT STANDARD TITLE Inspect and test a single phase domestic installation ORIGINATOR SGB Electrical Engineering & Construction PRIMARY OR DELEGATED QUALITY ASSURANCE FUNCTIONARY - FIELD Field 12 - Physical Planning and Construction ABET BAND UNIT STANDARD TYPE PRE-2009 SUBFIELD Electrical Infrastructure Construction Undefined Regular Level 3 Level REGISTRATION STATUS REGISTRATION START DATE REGISTRATION END DATE CREDITS SAQA DECISION NUMBER Reregistered SAQA 06120/18 LAST DATE FOR ENROLMENT LAST DATE FOR ACHIEVEMENT In all of the tables in this document, both the pre-2009 Level and the Level is shown. In the text (purpose statements, qualification rules, etc), any references to Levels are to the pre-2009 levels unless specifically stated otherwise. This unit standard replaces: US ID Unit Standard Title Pre-2009 Level Level Credits Replacement Status Test and inspect a single phase domestic installation Level 3 Level Complete PURPOSE OF THE UNIT STANDARD This unit standard is for persons in the Electrical Engineering; Generation; Distribution; Transmission, Construction and Renewable Energy Sector. A person credited with this unit standard will be capable of: Conducting an electrical test and inspection of a domestic single-phase installation to ensure compliance with all statutory Using appropriate test instruments and understanding the indicated results. Using appropriate inspection documents. Completing the appropriate inspection documents with correct and relevant information.

2 This unit standard will contribute to the full development of the learner within the electrical engineering and construction environment by providing recognition, further mobility and transportability within the field of Physical Planning and Construction. The skills, knowledge and understanding demonstrated within this unit standard are essential for social and economic transformation and upliftment within the electrical engineering and construction environment. This unit standard is a pre requisite for registration as an accredited person and does not give the learner the legal right to issue a Certificate of Compliance. The registering authority will do registration as an accredited person. This unit standard may not cover the Explosion Industry. LEARNING ASSUMED TO BE IN PLACE AND RECOGNITION OF PRIOR LEARNING The following knowledge, skills attitude and/or equivalent: Wire and commission domestic electrical circuits. Have awareness of the application of statutory regulations to the installation. UNIT STANDARD RANGE Specific Outcomes and Assessment Criteria: SPECIFIC OUTCOME 1 Plan the electrical installation tests to be done. Job instructions are interpreted and a sequence of operations is determined according to the installation environment and the required task. Appropriate tools, equipment and instruments are identified and selected to meet the requirements of the task according to statutory and environmental The correct documentation necessary to complete the task is obtained as per data management The safety rules and regulations regarding the task are understood according to statutory requirements and safe work procedures. Environmental hazards and safety risks are identified according to environmental standards and safety risk analyses. SPECIFIC OUTCOME 2 Inspect the electrical installation. Permission is obtained to carry out task as per local The installation is inspected for compliance to the statutory and environmental Appropriate documentation for the type of installation is completed as per data management

3 Any non-compliant components within the installation are identified and understood as per quality All safety requirements are observed and demonstrated during the inspection as per safe work procedures. SPECIFIC OUTCOME 3 Test the electrical installation. Permission is obtained to carry out task as per local Installation is tested according to the statutory requirements from the SANS code. Appropriate documentation is completed as per data management Appropriate test instruments are used competently to obtain meaningful readings in accordance with the statutory The measurements obtained from the test are understood as per SANS ASSESSMENT CRITERION 6 All safety precautions are observed and demonstrated during the test as per safe work procedures. SPECIFIC OUTCOME 4 Complete the required test and inspection documentation. All personnel, tools, instruments and excess equipment are removed from the installation according to work site procedures. The work area is restored to its original condition on completion of the test/inspection procedures as per safety The certificate of compliance is correctly and accurately completed according to applicable SANS The results of the inspection and test are communicated to all concerned as per reporting procedures. A defect list is compiled and corrective action taken if necessary as per quality

4 UNIT STANDARD ACCREDITATION AND MODERATION OPTIONS Anyone assessing a learner against this unit standard must be registered as an assessor with the relevant ETQA. Any institution offering learning that will enable achievement of this unit standard must be accredited as a provider through the relevant ETQA by SAQA. Moderation of assessment will be overseen by the relevant ETQA according to the moderation guidelines in the relevant qualification and the agreed ETQA procedures. UNIT STANDARD ESSENTIAL EMBEDDED KNOWLEDGE Knowledge that will help me understand and that I will be able to explain: Working knowledge of SANS Inspection documents and check lists pertaining to a single phase installation including the contents of a Certificate of Compliance. Understand the concepts of a single phase installation and its environment. Types of material/equipment that may be used in electrical installations. Appropriate fault finding techniques for a single phase installation. Important factors affecting the safety of the installation for the user. The importance of accurately recording data and test results. The importance of understanding the SANS code in order to recognise defects and their specific relationship to the code requirements for installed electrical equipment. UNIT STANDARD DEVELOPMENTAL OUTCOME UNIT STANDARD LINKAGES Critical Cross-field Outcomes (CCFO): UNIT STANDARD CCFO ORGANISING Organise oneself and ones activities responsibly and effectively (with the ability to follow instructions when working by ones self or in a work team, ensure safe execution of work activities). UNIT STANDARD CCFO COLLECTING Collect, evaluate, organise and critically evaluate information related to maintaining and repairing electric power tools. UNIT STANDARD CCFO COMMUNICATING Effective use of communication methods when giving instructions to fellow workers, following of instructions, recording and reporting information. UNIT STANDARD CCFO SCIENCE Use science and technology effectively and critically, showing responsibility towards the environmental and the health of others (maintaining lighting systems to ensure that all safety and environmental conditions are considered). UNIT STANDARD CCFO DEMONSTRATING Tasks, using responsible thinking and decision making (in relation to the use and choice of relevant personal protective and safety equipment). UNIT STANDARD ASSESSOR CRITERIA REREGISTRATION HISTORY As per the SAQA Board decision/s at that time, this unit standard was Reregistered in 2012; 2015.

5 UNIT STANDARD NOTES This unit standard replaces unit standard , which is "Test and inspect a single phase domestic installation", Level 3, 10 Credits. Originally re-registered on 11 February 2004 under SAQA decision number 2552/04. Supplementary Information: Specified requirements include legal and legislative specific requirements and are contained in one or more of the following documents: SANS Occupational Health & Safety Act. QUALIFICATIONS UTILISING THIS UNIT STANDARD: Core ID QUALIFICATION TITLE National Certificate: Electrical Engineering PRE Level 3 Level 03 STATUS Passed the End Date - Status was "Registered" END DATE PRIMARY OR DELEGATED QA FUNCTIONARY As per Learning Programmes recorded against this Qual