DURANEX Grade Catalog DURANEX. Polybutylene Terephthalate ( PBT ) Grade Compositions

Transcription

1 DURANEX Grade Catalog DURANEX Polybutylene Terephthalate ( PBT ) Grade Compositions

2 DURANEX Grade Compositions DURANEX is a crystalline thermoplastic based on polybutylene terephthalate (PBT) that can be readily strengthened, modified, or otherwise performanceenhanced through the addition of glass fibers or other inorganic filler additives. Therefore, as grades can be optimally designed depending on the application, various grades are provided, including flame-retardant grades, reinforced grades, and impact-resistant grades. Well-balanced highly reliable plastics DURANEX, due to its mechanical strength, heat stability, electrical resistivity and wear and abrasion-resistance, offers great potential as a well-balanced, highly reliable material, having a wide variety of applications including electronic / electro-mechanical and automobile parts and various other functional parts. Sophisticated quality to fit your precise needs Not only does it have well-balanced properties as a raw material, DURANEX also assures moldability, dimensional stability, glossy surfaces and various fabrication capabilities providing higher added value GF15% 0 GF% 00 GF0% 00 GF0% 05 GF5% 0H GF.5% 5H GF15% 00H High flow Toughness % kj/m 5 / 5 / kv/mm cm CTI Nominal strain at break, , , , , , , , , , FR, UL approved regrind 50% Low gas generation, Low contact contamination, FR, UL approved regrind 50% GF.5% 16 6 GF % 16 GF 0% CN00 CN15 CN0 GF 0% CRN00 CRN15 CRN0 GF 0% 1. 5, , , , , , , , ,050. Nominal strain at breakflame retardancy (UL certification) is unaffected even at recyclate loadings up to 50% , ,50. All figures in the table are the typical values of the material and not the minimum values of the material specifications. For qualified values of UL (Underwriters Laboratories Inc.) refer to the yellow card (File No.E 15) issued by UL. DURANEX-1

3 Low warpage LD 500 GF 0% 50LD 150 GF 0% GF 0% W 1W 0W CN0XB GF GF GF GF GF GF Super low warpage % ,500,1,0 6,0,0 6,500,500,500 6,10, 1, kj/m / 5 / 6. kv/mm 6 6 cm CTI Nominal strain at break Low warpage Hydrolysis resistant 600B 6B GB 0% 1SA Mineral 0SA GF 1SA GF 11SA GF 61SA GF 51SA GF 65SA Mineral 0HR 51HS Heat shock resistant Anisotropy improvement Low density, Low wear Hydrolysis resistant ,00.0, 1.,0.1 5,,000,6 5. 5,0,60.6 5,500.,0 11.0, V-1 Nominal strain at break All figures in the table are the typical values of the material and not the minimum values of the material specifications. For qualified values of UL (Underwriters Laboratories Inc.) refer to the yellow card (File No.E 15) issued by UL. DURANEX-

4 Resin adhesion improved for multiple injection molding Epoxy adhesion improved Higher gloss, Better surface appearance 1RA 0RA 5RA 5A MS GF Hydrolysis resistant High stiff, Low warp, Less sinking % kj/m,0 11.,0.0.0,0 5, ,0. 6,00.,0 15, / 5 / 1 kv/mm 1 cm CTI Nominal strain at break Low friction, Low wear Weather resistance Antistatic Electric Higher comparative conductive Tracking index,fr PBT for film, Extrusion 0K 60T Mineral 600T Mineral 00F AW CN10 GF 0U CA0NX 00E CTN1 0FP 00FP GF GF Super high High flow flow 500FP 0FP standard High viscosity 00FP Super high viscosity, CTI rank 0 standard ,0,000,0,6,0,,60 1,0,000,50,0,0,0,0, Nominal strain at break All figures in the table are the typical values of the material and not the minimum values of the material specifications. For qualified values of UL (Underwriters Laboratories Inc.) refer to the yellow card (File No.E 15) issued by UL. DURANEX-

5 NOTES TO USERS All property values shown in this brochure are the typical values obtained under varying conditions prescribed by applicable standards and test s. This brochure has been prepared based on our own experiences and laboratory test data, and therefore all data shown here are not always applicable to parts used under different conditions. We do not guarantee that these data are directly applicable to the application conditions of users and we ask each user to make his own decision on the application. It is the users responsibility to investigate patent rights, service life and potentiality of applications introduced in this brochure. Materials we supply are not intended for the implant applications in the medical and dental fields, and therefore are not recommended for such uses. For all works done properly, it is advised to refer to the appropriate Technical Catalog for specific material processing. For safe handling of materials we supply, it is advised to refer to the Material Safety Data Sheet MSDS of the proper material. This brochure is edited based on reference literatures, information and data currently available to us. So the contents of this brochure are subject to change without notice due to new data. Please contact our office for any questions about products we supply, descriptive literatures or any description in this brochure. WinTech Polymer Ltd. is a member of the Polyplastics Group, while the DURANEX PBT resin manufactured and sold by that firm is marketed by Polyplastics affiliated companies in the regions listed below. DURANEX is a trademark of Polyplastics Co., Ltd. in Japan and other countries. POLYPLASTICS CO., LTD. JR Shinagawa East Bldg., 1-1, Konan -chome, Minato-ku, Tokyo, -0 Japan Tel: Fax: JR Shinagawa East Bldg., 1-1, Konan -chome, Minato-ku, Tokyo, -0 Japan Tel: Fax: Affiliates Polyplastics Asia Pacific Sdn. Bhd. (Kuala Lumpur) Polyplastics Asia Pacific Singapore Pte. Ltd. (Singapore) Polyplastics Marketing (India) Private Ltd. (India) Polyplastics Marketing (T) Ltd. (Bangkok) Polyplastics Taiwan Co., Ltd. (Taipei) Polyplastics China Ltd. (Hong Kong) Polyplastics Trading (Shanghai) Ltd. (Shanghai) Polyplastics (Shanghai) Ltd. (Shanghai) PTM Engineering Plastics (Nantong) Co.,Ltd. (Nantong) 0. (V005)