Laboratory Experiments in Corrosion Engineering II
|
|
- Gervase Hill
- 6 years ago
- Views:
Transcription
1 Lecture - 40 Laboratory Experiments in Corrosion Engineering II Keywords: Polarization Experiments, Pitting Potentials, Microbial Corrosion. A. Electrochemical tests in a given environment Polarization curves and Tafel plots for generalized corrosion. Polarization resistance measurements. Corrosion potential, pitting and repassivation potential. Galvanic coupling effect on polarization curves. Electrochemical impedance (to study behavior of coating, passivation). Anodic polarization for establishing active-passive behavior of metals and alloys in different environments Anodic protection. Impressed current cathodic protection. In order to establish Tafel constants, corrosion potential, corrosion current and exchange currents, extrapolated regions of anodic and cathodic curves have to be used. Two types of approach a. Wide range of overpotentials with reference to rest potential (for example, -150mV to +150mV), to facilitate determination of Tafel slopes through extrapolation to the corrosion potential. b. Narrow range of overpotentials (+20 mv to -20mV), facilitating determination of linear polarization resistance (slow scan rate). 1
2 Description of cell and experimental arrangements are given in Fig 40.1 and Fig Typical electrolytic cell with various electrodes for polarization measurements Fig Automatic polarization measurement 2
3 B. Measurement of pitting potentials: Cyclic polarization techniques can be used to evaluate pitting tendency of an active-passive metal or alloy (Fig. 40.3). A potential scan starting from E corr in the anodic direction is applied till significant current increase occurs. The final potential is negative with reference to repassivation potential. The potential where the loop closes on the reverse scan is the protection potential, which can also be estimated by extrapolating the reverse scan to zero current. Pitting potential (E pit ) corresponds to the potential at which current increases sharply. The larger the loop, the higher the tendency for pitting. Pitting shows up as an increasing anodic current before transpassive corrosion or evolution of oxygen. Fig Cyclic polarization to determine pitting and protection potentials. New pits can initiate only above pitting potential, and not between E pit and E prot. No hysteresis is exhibited by an alloy which is resistant to pitting. There will be potential and current distributions around pits. 3
4 C. Experiments for evaluation of sensitization in stainless steels. Study chromium depletion and precipitation as carbides at the grain boundaries. Oxalic acid test: Polished specimen is anodically etched at 1A/cm 2 for a minute in 10% oxalic acid at room temperature. Examine the specimen under the microscope to reveal step, dual or ditch structures. D. Determination of effect of alloy chemistry on passivation parameters: For development of corrosion resistant alloys with reference to active passive behavior, the following key parameters need to be optimized. E pp Primary passive potential i crit Critical anodic passivating current density. 1. Establish Anodic polarization curves for iron, nickel and chromium in 1N H 2 SO 4. Comment on the passivity curves with respect to passivity potential range, E pp and i crit. 2. Establish the effect of chromium (0 30%) in stainless steels on E pp and i crit in 1N H 2 SO 4. Plot your results with respect to (a) E pp Vs percent chromium (b) i crit Vs percent chromium 3. Determine pitting potentials for 18-8 stainless steel in different chloride concentrations. E. Corrosion testing for metals and alloys The following systems for corrosion testing are available, each covering different method of corrosion evaluation Humidity test chamber Salt spray Temperature and humidity control. Test set-up for alternate immersion testing of metals and alloys in 3.5% NaCl solution for stress corrosion testing. 4
5 Bimetallic corrosion testing in specific liquids under humidity control current and potential difference recorded. F. Laboratory techniques for studying amenability to MIC due to biofilms: Evaluation of biofilms from deposit samples collected from various locations organic and inorganic content of biofilms. Carbohydrate and protein analysis (spectrophotometer) Presence of aerobes and anaerobes in the deposits. Redox potential measurements in liquid samples. Corrosion potential measurements Biofilm growth on metal surface influences anodic and cathodic reactions Shifting of corrosion potentials in positive or negative directions to be monitored. Examples: Stainless steels in aerated seawater Mild steel in anaerobic seawater. Distinguish between aerobic and anaerobic corrosion. Polarization experiments in the presence and absence of biofilms on metals in the presence and absence of microorganisms. G. Monitoring and characterization procedures for different bacteria involved in MIC are listed in Table Microbiological aspects of MIC microbes are illustrated in lectures Various strains of different bacterial species can be procured from culture banks and characterized as per recommended procedures. 5
6 Table 40.1 Testing and Analyses of different bacteria relevant to MIC, Type of Bacteria Monitoring and characterization 1. Acid producing Production of inorganic and organic acids attack on various metals and alloys. 2. Denitrifying Ammonia production attack on copper alloys. 3. Iron-related Ferrous oxidation and ferric-reductionplugging of water and oil pipelines- tubercle formation. 4. Slime-forming Slime-sludge characterization. 5. Sulfate-reducing Sulfide production (H 2 S) FeS production - corrosion of metal surfaces. Common media used for routine isolation of bacteria and fungi Filamentous fungi - Potato Dextrose Agar Aerobic and anaerobic bacteria - Nutrient Agar Pseudomonas Sp - Select media from literature Sulfate Reducing Bacteria (SRB) - Postgate media 6
7 H. Microbially influenced corrosion of aluminium alloys Choose desired aluminium alloys and make suitable specimens. Use naturally collected sea water and fresh water samples from identified locations. A biofilm growth chamber (under conditions of both stagnant and flowing liquid) can be constructed to expose the metallic specimens for different periods of time. Monitor biofilm growth by removing specimen frequently and characterize the biofilm with respect to thickness, microbial assay, chemical and metallurgical analysis, surface roughness and morphology. Isolate important bacterial species from the biofilm and carry out steady-state potential and polarization measurements in the presence and absence of isolated bacteria. I. Biofouling and MIC of stainless steels in sea water. Experiments similar to the previous one for aluminium alloys. J. Microbial diversity of pipelines and establishment of MIC Locate a pipeline transporting water and petroleum products. From the pipeline, collect aseptically, samples of water, oil and corrosion products (debris). a) Visual, physical and chemical characterization of the water, oil and debris samples for colour, chemical composition, ph. b) Isolation and enumeration of different types of microorganisms through standard microbiological procedures characterization of isolated organisms with respect to Autotrophs, Heterotrophs. Bacteria, fungi Aerobe, anaerobe Iron oxidising, Manganese oxidising. c) Based on the microbial assay and characterization and failure analysis of the pipeline samples, predict nature of MIC (Microbially influenced corrosion) 7
8 K. Examination of biocorrosion of concrete in the laboratory simulating sewer conditions Samples of sewer pipes collected from sewerage processing stations can also be used. Corrosion testing coupons Fresh coupons from new sewer pipes. Coupons prepared from corroded concrete slabs from sewer treatment plants. Corrosion chambers for exposing the coupons to bacterial activity under simulated conditions can be used. Monitor conditions with respect to ph changes, H 2 S generation, temperature and humidity. Growth of Anaerobic Sulfate Reducing Bactria (SRB), aerobic sulfur oxidizers such as Acidithiobaullus can be monitored and their role on concrete corrosion assessed. L. Bacterial kinetics of sulfur oxidation of Acidithiobacillus thiooxidans and its influence on concrete corrosion. Experimental strategy: Bacterial growth in recommended media. Growth curve with respect to cell number, ph and sulfate concentration as a function of time. Establish bacterial growth kinetics. Concrete corrosion tests in aqueous media at bacterial acidic ph under different conditions of temperature, metal-ion concentrations, and types of reinforcement steels. 8
9 M. Corrosion testing for medical implants Compatibility Tissue response Dissolution rates Toxicity In vivo corrosion How susceptible is the implant metal to corrosion? Effect of corrosion on body response Rest potential : Measurements over extended periods of time to predict metal dissolution. Cyclic potentiodynamic polarization: Corrosion susceptibility of small implant devices. Galvanic corrosion: Coupled and uncoupled leach rates. Fretting: Fretting corrosion in moving body parts. Various metal and alloy samples representative of implant materials can be shaped into electrodes and tested in body fluids and simulated electrolytes. 9
Assignments. 1. Prepare Galvanic series for metals and alloys in flowing sea water. Compare this with the series available for stagnant sea water.
Assignments 1. Prepare Galvanic series for metals and alloys in flowing sea water. Compare this with the series available for stagnant sea water. 2. Construct the Eh ph diagram for the Zn H 2 O O 2 system
More informationLecture 24 Microbially Influenced Corrosion (MIC) Definitions, Environments and Microbiology
Lecture 24 Microbially Influenced Corrosion (MIC) Definitions, Environments and Microbiology Keywords: Microbial Corrosion, Microorganisms, Biofouling. Introduction Microbially-influenced corrosion (MIC)
More informationBiofilms And General Mechanisms In Biocorrosion
Lecture 35 Biofilms And General Mechanisms In Biocorrosion Keywords: Biofilms, Structural Materials, Sulfate Reducing Bacteria Biofilms on metals and alloys can cause several engineering problems. [227-235]
More informationCorrosion. Cause of Corrosion: Electrochemical Mechanism of Corrosion (Rusting of Iron)
Corrosion Any process of deterioration (or destruction) and consequent loss of a solid metallic material, through an unwanted (or unintentional) chemical or electrochemical attack by its environment, starting
More informationOEST 740. Marine Biofilms: Ecology and Impact. Spring Instructor: Kristina Mojica
OEST 740 Marine Biofilms: Ecology and Impact Spring 008 Instructor: Kristina Mojica Biocorrosion This chapter considers the issue of biofilm based bacterial assisted corrosion (i.e. biocorrosion) of metals
More informationJamal Shamas, Sc.D., P.E.
Jamal Shamas, Sc.D., P.E. Microbially Induced Corrosion (MIC) in Water & Wastewater Conveyance and Treatment Systems 1 st NACE-Jubail Industrial Forum Water Treatment & Cathodic Protection 17-19 October
More informationTutorial Corrosion II. Electrochemical characterization with EC-Lab techniques
Tutorial Corrosion II Electrochemical characterization with EC-Lab techniques 1 OUTLINE 1. Introduction 2. Types of corrosion a) Uniform corrosion b) Localized corrosion 3. Corrosion experiment 4. EC-Lab
More informationCorrosion Rate Measurement on C-Steel
Measurements of corrosion rate on Carbon-steel using Electrochemical (potentiodynamic Polarization, EIS etc.) technique. Corrosion Rate Measurement on C-Steel Abdullah Al Ashraf 1. Introduction: The degradation
More informationMicrobiologically Influenced Corrosion Corrosion Mechanisms
Microbiologically Influenced Corrosion Microbiologically Influenced Corrosion is defined as corrosion at a metal surface that is associated with microorganisms, or the products of their metabolic activities
More informationA New qpcr Array for Costeffective Quantification of MIC Microorganisms
A New qpcr Array for Costeffective Quantification of MIC Microorganisms Kerry Sublette University of Tulsa Dora Ogles, Brett Baldwin, Anita Biernacki, Katherine Clark Microbial Insights, Inc. What is MIC?
More informationCORROSION AND CORROSION CONTROL An Introduction to Corrosion Science and Engineering
CORROSION AND CORROSION CONTROL An Introduction to Corrosion Science and Engineering FOURTH EDITION R. Winston Revie Senior Research Scientist CANMET Materials Technology Laboratory Natural Resources Canada
More informationCorrosion Control and Cathodic Protection Data Sheet
Data Sheet CORROSION CONTROL Corrosion control is the application of engineering principles and procedures to minimise corrosion to an acceptable level by the most economical method. It is rarely practical
More information1. Introduction. Figure 1: Open Recirculation Cooling Water Tower (image courtesy of Solenis) Page 3
Table of Contents 1. Introduction... 3 2. Description of Root Causes of Corrosion... 4 3. Electrochemical Corrosion... 6 4. Under-Deposit Corrosion... 8 5. Microbial-Induced Corrosion... 9 6. Corrosion
More informationCorrosion and batteries
Corrosion and batteries Corrosion is a process of gradual destruction of metal from its surface due to its unwanted chemical or electrochemical interaction of metal. Ore of metal which is stable and is
More informationAnnex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005
Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-PL-18716-01-00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 17.11.2014 to 13.05.2018 Holder of certificate: Institut
More information14. Based on published literature, critically analyze various heap bioleaching models.
Assignments 1. What do you mean by biogenesis? With respect to sulfur cycle in nature, explain the role of acidophilic microorganisms and anaerobic sulfate reducers in the formation, dissolution and precipitation
More informationApplication Note CORR-4
Application Note CORR-4 Subject: Electrochemistry and Corrosion: Overview and Techniques INTRODUCTION During the late 70 s and early 80 s, corrosion specialists began to discover that electrochemical (ECHEM)
More informationPotentiodynamic Scanning (PDS) of Stainless Steel Karen Louise de Sousa Pesse
Potentiodynamic Scanning (PDS) of Stainless Steel 8-2-26 Supervision: Elien Wallaert Introduction In order to investigate the corrosion resistance of Stainless steel in a specific environment, the practical
More informationWhat happens if we connect Zn and Pt in HCl solution? Corrosion of platinum (Pt) in HCl. 1. If Zn and Pt are not connected
Corrosion of platinum (Pt) in HCl Now if we place a piece of Pt in HCl, what will happen? Pt does not corrode does not take part in the electrochemical reaction Pt is a noble metal Pt acts as a reference
More informationCrack Initiation and Crack Propagation of Pre-corroded Ni-16Cr Alloy in 4.5%NaCl Aqueous Solution
IOSR Journal of Engineering (IOSRJEN) e-issn: 2250-3021, p-issn: 2278-8719 Vol. 3, Issue 8 (August. 2013), V2 PP 11-15 Crack Initiation and Crack Propagation of Pre-corroded Ni-16Cr Alloy in 4.5%NaCl Aqueous
More informationProtection against microbiological corrosion and developments in corrosion detection. Corina Prent
Protection against microbiological corrosion and developments in corrosion detection. Corina Prent Contents Corrosion Microbial interaction with iron Prevention off microbial corrosion New technology for
More informationDistribution Review. Corrosion Control. Corrosion Control Vocabulary. American Water College 1. Corrosion Control Training Objectives
Distribution Review Corrosion Control Corrosion Control Training Objectives To gain an understanding of: Corrosion control vocabulary The factors affecting corrosion Methods used to control corrosion Alkalinity
More informationMICROBIOLOGICALLY INFLUENCED CORROSION ANALYSIS ON CARBON STEEL COUPONS
U.P.B. Sci. Bull., Series B, Vol. 80, Iss. 4, 2018 ISSN 1454-2331 MICROBIOLOGICALLY INFLUENCED CORROSION ANALYSIS ON CARBON STEEL COUPONS Mădălina ANDREI 1, Brânduşa GHIBAN 2 The paper is focused on investigating
More informationCORROSION PHENOMENA AN INTRODUCTION G P Rothwell
CORROSION PHENOMENA AN INTRODUCTION G P Rothwell The objective of this talk is to provide broad-brush comments on a wide range of corrosion phenomena in order to provide a measure of common ground for
More informationSTP1421-EB/Aug Subject Index
STP1421-EB/Aug. 2002 Subject Index A Airflow simulations, 19 Air temperature, 103 Alternating current impedance technique, 171 Aluminum, 3, 59 aluminum coating, 284 aluminum-zinc alloy-coated steel, 284
More information2. Wet Corrosion: Characteristics, Prevention and Corrosion Rate
2. Wet Corrosion: Characteristics, Prevention and Corrosion Rate Mighty ships upon the ocean suffer from severe corrosion. Even those that stay at dockside are rapidly becoming oxide Alas, that piling
More informationGalvanic corrosion evaluation of 6061 aluminum coupled to CVD coated stainless steel Elizabeth Sikora and Barbara Shaw 6/9/2016
SHAW AND ASSOCIATES CONSULTING Galvanic corrosion evaluation of 6061 aluminum coupled to CVD coated stainless steel Elizabeth Sikora and Barbara Shaw 6/9/2016 Evaluation of galvanic corrosion of aluminum
More informationMat E 272 Lecture 26: Oxidation and Corrosion
Mat E 272 Lecture 26: Oxidation and Corrosion December 11, 2001 Introduction: Environmental degradation of materials is one of the most costly failure modes, accounting for over 5 percent of the total
More informationElectrochemical study on corrosion of different metals exposed to deaerated geothermal brines containing CO 2
Electrochemical study on corrosion of different metals exposed to deaerated geothermal brines containing CO 2 N. Mundhenk 1, P. Huttenloch 2, R. Zorn 2, and T. Kohl 1 1 Institute of Applied Geosciences
More informationCorrosion Simulation. OLI Simulation Conference A. Anderko, G. Engelhardt and M.M. Lencka
OLI Simulation Conference 2010 Corrosion Simulation Think Simulation! Harnessing the power of the OLI Engine A. Anderko, G. Engelhardt and M.M. Lencka General and localized corrosion models Single-phase
More informationPrevention Strategies Design and Coatings
Lecture 14 Prevention Strategies Design and Coatings Keywords: Corrosion Prevention, Designs, Protective Coatings. There are a number of methods to control corrosion. The choice of any one control technique
More informationIN SITU MONITORING OF REINFORCEMENT CORROSION BY MEANS OF ELECTROCHEMICAL METHODS
ABSTRACT IN SITU MONITORING OF REINFORCEMENT CORROSION BY MEANS OF ELECTROCHEMICAL METHODS Oskar Klinghoffer, M.Sc. FORCE Institute, Park Allé 345, DK-2605 Brøndby, Denmark The well-known and usually adapted
More informationA Case Study: Corrosion Failure of Tube Heat Exchanger
doi: 10.14355/me.2015.04.007 A Case Study: Corrosion Failure of Tube Heat Exchanger Ibrahim M Ghayad, Z. Abdel Hamid, N. Gomaa Central Metallurgical Research & Development Institute (CMRDI), P.O.Box:87
More informationCORROSION RESISTANCE OF PLASMA NITRIDED AND NITROCARBURIZED AISI 316L AUSTENITIC STAINLESS STEEL
CORROSION RESISTANCE OF PLASMA NITRIDED AND NITROCARBURIZED AISI 316L AUSTENITIC STAINLESS STEEL F.A.P. Fernandes 1*, J. Gallego 2, G.E. Totten 3, C.A. Picon 2, L.C. Casteletti 1 1 Department of Materials
More informationSensitization & Corrosion Behaviour of Austenitic Stainless Steel 304 & 316
Sensitization & Corrosion Behaviour of Austenitic Stainless Steel 304 & 316 Manish Kumar Verma Mechanical, Columbia Institute of Engineering & Technology, Raipur (India) ABSTRACT Austenitic Stainless steels
More informationMethods for Studying Biocorrosion: : Part II -Localised Techniques-
Advanced Electrochemical Rolf Gubner Swedish Corrosion Institute Kräftriket 23A 10405 Stockholm Sweden Tel: +46 8 674 1745 Fax: +46 8 674 1780 Rolf.Gubner@corr-institute.se www.corr-institute.se Methods
More informationSelected Publications and Abstracts on Multielectrode Array Sensors for Corrosion Monitoring
Selected Publications and Abstracts on Multielectrode Array Sensors for Corrosion Monitoring 2007 1. Coupled Multielectrode Array Systems and Sensors in Corrosion Inspection and Monitoring, Pierre R. Roberge,
More informationCathodic Protection Influencing Factors and Monitoring
Lecture 17 Cathodic Protection Influencing Factors and Monitoring Keywords: Coated Surfaces, Protection Criterion, Anode Materials, Pipeline Protection. For large structures such as underground pipe lines,
More informationTHE ELECTROCHEMISTRY OF CORROSION Edited by Gareth Hinds from the original work of J G N Thomas
THE ELECTROCHEMISTRY OF CORROSION Edited by Gareth Hinds from the original work of J G N Thomas INTRODUCTION The surfaces of all metals (except for gold) in air are covered with oxide films. When such
More informationElectrochemical screening of several alloys for use in a flue-gas desulphurisation prescrubber
36 1989 ROI www.hbscc.nl - 1 - Electrochemical screening of several alloys for use in a flue-gas desulphurisation prescrubber L.M. Butter, E.J.A. Vogelaar, W.M.M. Huijbregts Kema Scientific & Technical
More informationRusting is an example of corrosion, which is a spontaneous redox reaction of materials with substances in their environment.
CORROSION WHAT IS CORROSION? Corrosion is the deterioration of a metal as a result of chemical reactions between it and the surrounding environment. Rusting is an example of corrosion, which is a spontaneous
More informationCorrosion of Metals. Industrial Metallurgists, LLC Northbrook, IL Copyright 2013 Industrial Metallurgists, LLC
Corrosion of Metals Industrial Metallurgists, LLC Northbrook, IL 60062 847.528.3467 www.imetllc.com Copyright 2013 Industrial Metallurgists, LLC Course structure Learning modules 1. Introduction to corrosion
More informationINFLUENCE OF INHIBITORS IN COOLING EMULSION UPON MAIN CUTTING FORCE AND CORROSION OF WORKPIECE
INFLUENCE OF INHIBITORS IN COOLING EMULSION UPON MAIN CUTTING FORCE AND CORROSION OF WORKPIECE I.Juraga, K.Mihoci, V.Alar, V.Šimunović, I.Stojanović Faculty of Mechanical Engineering and Naval Architecture
More informationGREEN CORROSION INHIBITORS
GREEN CORROSION INHIBITORS Theory and Practice V. S. SASTRI WILEY A John Wiley & Sons, Inc., Publication CONTENTS Preface 1 Introduction and Forms of Corrosion 1.1 Definition, 1 1.2 Developments in Corrosion
More informationDRAFT EVALUATION OF CORROSION RESISTANCE OF MICROALLOYED REINFORCING STEEL
DRAFT EVALUATION OF CORROSION RESISTANCE OF MICROALLOYED REINFORCING STEEL By Javier Balma David Darwin JoAnn P. Browning Carl E. Locke, Jr. A Report on Research Sponsored by GERDAU AMERISTEEL CORPORATION
More informationACCELERATED CORROSION TESTING OF GALVANIC COUPLES. James F. Dante, Josh Averett, Fritz Friedersdorf, and Christy Vestal
ACCELERATED CORROSION TESTING OF GALVANIC COUPLES James F. Dante, Josh Averett, Fritz Friedersdorf, and Christy Vestal Luna Innovations 706 Forest St. Suite A Charlottesville, VA 22903 dantej@lunainnovations.com
More informationMetropolitan Water Reclamation District of Greater Chicago 10/19/ Mark Joyce Senior Mechanical Engineer Engineering Department
Metropolitan Water Reclamation District of Greater Chicago 10/19/201 2 Mark Joyce Senior Mechanical Engineer Engineering Department 1 Definition of Corrosion Corrosion is the deterioration of a substance
More informationa clean cooling advantage
a clean cooling advantage TM OBJECTIVE Raise awareness of the role microbio plays in the overall the technical success of treatment programs. TM a clean cooling advantage OBJECTIVE Develop a practical
More informationMetallurgical Properties Influencing Corrosion
Lecture 38 Metallurgical Properties Influencing Corrosion Keywords: Metallurgical Properties, Intergranular Corrosion, Hydrogen Embrittlement, Iron Pillar Metallurgical properties and structure influence
More informationCOMPOSITION, STRUCTURE AND SOME CORROSION PROPERTIES OF AS-RECEIVED NdFeB MAGNETIC MATERIAL AND PROTECTIVE ZnAl COATING
COMPOSITION, STRUCTURE AND SOME CORROSION PROPERTIES OF AS-RECEIVED NdFeB MAGNETIC MATERIAL AND PROTECTIVE ZnAl COATING Stanislav LASEK, Miroslav KURSA, Kateřina KONEČNÁ VŠB-TU Ostrava, 17. listopadu 15/2172,
More informationppm Dissolved Oxygen Measurement
ppm Dissolved Oxygen Measurement INTRODUCTION Dissolved oxygen (D.O.) levels are used as a general indicator of water quality. Oxygen is essential to life and vital for countless aquatic forms. D.O. level
More informationOFFSHORE CATHODIC PROTECTION 101: WHAT IS IT AND HOW DOES IT WORK? Dick Baxter & Jim Britton
This PDF document contains Live Web Links Click them for more information from the web OFFSHORE CATHODIC PROTECTION 101: WHAT IS IT AND HOW DOES IT WORK? Dick Baxter & Jim Britton www.cathodicprotection101.com
More informationEffect of Velocity of Cleaning Pigs on the Efficiency of Fluid Delivery in the Pigged Pipeline System
Report and Opinion, 29;1(5) Technical Report Effect of Velocity of Cleaning Pigs on the Efficiency of Fluid Delivery in the Pigged Pipeline System Chukwuka Ikechukwu Nwoye 1, Udeme Okure 1, Uzoma Odumodu
More informationChapter 16 Corrosion and Degradation of Materials
Chapter 16 Corrosion and Degradation of Materials Concept Check 16.1 Question: Would you expect iron to corrode in water of high purity? Why or why not? Answer: Iron would not corrode in water of high
More informationErosion corrosion of mild steel in hot caustic. Part II: The evect of acid cleaning
Corrosion Science 48 (2006) 2660 2675 www.elsevier.com/locate/corsci Erosion corrosion of mild steel in hot caustic. Part II: The evect of acid cleaning Rihan Omar Rihan, Srdjan NeniT The Department of
More informationLecture 19 Biotechnology For Gold Biogenesis, Microorganisms And Gold Nanobiotechnology
Lecture 19 Biotechnology For Gold Biogenesis, Microorganisms And Gold Nanobiotechnology Keywords: Gold Biogenesis, Microorganisms, Mechanisms In lectures 19-21, biotechnological aspects of gold production
More informationGalvanic Corrosion Prevention Guide for Water Cooling Systems
WATER COOLED DEVICES Galvanic Corrosion Prevention Guide for Water Cooling Systems November 2017 White Paper Created by Helen E. Kane, Advanced Energy Industries, Inc. Water Cooled Devices Abstract This
More informationDurable offshore wind Corrosion control. AMC Seminar, Den Helder, 3 november 2011 Johan van Malsen
Durable offshore wind Corrosion control AMC Seminar, Den Helder, 3 november 2011 Johan van Malsen 3-11-2011 AMC Seminar Outline of presentation TNO Corrosion Corrosion control Research and Development
More informationCORROSION & ITS CONTROL -Content. Introduction Classification Galvanic series Factors affecting Protection methods Summary
CORROSION & ITS CONTROL -Content Introduction Classification Galvanic series Factors affecting Protection methods Summary 3 Learning Objectives At the end of the chapter the learner will be able to; 1.
More informationKinetic Characteristics of Different Materials used for Bolting Applications
Kinetic Characteristics of Different Materials used for Bolting Applications Report Kinetic Characteristics of Different Materials used for Bolting Applications Overview One of the most common problems
More informationElectrochemical response of permanent magnets in different solutions
Electrochemical response of permanent magnets in different solutions G. Gaona-Tiburcio, F. Almeraya-Calderón, J. G. Chacón-Nava, J. A. Matutes-Aquino, A. Martínez-Villafañe Abstract Materials for permanent
More informationInsititue of Paper Science and Technology Central Files CORROSION CONTROL ANNUAL RESEARCH REVIEW HANDOUT BOOK
Insititue of Paper Science and Technology Central Files CORROSION CONTROL ANNUAL RESEARCH REVIEW HANDOUT BOOK J CORROSION CONTROL HANDOUT BOOK April 2, 1991 CONTENTS PROJECT 3309 FUNDAMENTALS OF CORROSION
More informationIntroduction to Corrosion Science
E. McCafferty Introduction to Corrosion Science Springer Contents 1 Societal Aspects of Corrosion 1 We Live in a Metals-Based Society 1 Why Study Corrosion? 1 Corrosion and Human Life and Safety 1 Economics
More informationImprovement of corrosion resistance of HVOF thermal sprayed coatings by gas shroud
Improvement of corrosion resistance of HVOF thermal sprayed coatings by gas shroud Jin Kawakita, Takeshi Fukushima, Seiji Kuroda, and Toshiaki Kodama National Research Institute for Materials Science Abstract
More informationPassivity Definitions and Influencing Parameters
Lecture 20 Passivity Definitions and Influencing Parameters Keywords: Definition of Passivity, Flade Potential, Anodic Polarization, Critical Anodic Current Density. In the Eh ph diagrams, resistance to
More informationStress Corrosion Cracking
Stress Corrosion Cracking SCC is the brittle cracking of a metal due to the result of combined effects from localized corrosion and a tensile stress. Stress Corrosion Cracking Stress Corrosion Cracking
More informationThink Simulation! Adventures in Electrolytes. Corrosion Simulation. October 17, 2012
Think Simulation! Adventures in Electrolytes Corrosion Simulation October 17, 2012 OLI Simulation Conference 2012 Scope Review of corrosion simulation models Progress in modeling general corrosion: Cu-Ni
More informationROLES OF PASSIVATION AND GALVANIC EFFECTS IN LOCALIZED CO 2 CORROSION OF MILD STEEL
Paper No. 08332 ROLES OF PASSIVATION AND GALVANIC EFFECTS IN LOCALIZED CO 2 CORROSION OF MILD STEEL Jiabin Han, Yang Yang, Srdjan Nesic and Bruce N Brown Institute for Corrosion and Multiphase Technology,
More informationA Brief Introduction to MIC
Managing Microbiological Corrosion in Canada s Offshore & Onshore Oil Production Operations A Brief Introduction to MIC Rick Eckert, Senior Principal Engineer, DNV GL Columbus Ohio 1 Microbiologically
More informationCORROSION. Corrosion: Is the deterioration of metal due to its interaction with the surrounding environment. Electrochemical Nature of Corrosion.
CORROSION Corrosion: Is the deterioration of metal due to its interaction with the surrounding environment. Electrochemical Nature of Corrosion - + Pt Zn HCl Anodic process: oxidn Zn Zn 2 + + 2e - Cathodic
More informationCharacterization of the Corrosion Scenarios on the Trans-Canada Pipeline (Alberta System)
Characterization of the Corrosion Scenarios on the Trans-Canada Pipeline (Alberta System) (Interim Report: Dec. 20, 2005 - Feb. 28, 2006) P. Q. Wu, Z. Qin, and D. W. Shoesmith The University of Western
More informationLocalized corrosion behaviour of nickel-free high-nitrogen 19Cr-18Mn-0.69N austenitic stainless steel in 3.5-% NaCl
from R&D reviewed paper Pandurangan Saravanan and Vngaranahalli Srinivasan Raja: Localized corrosion behaviour of nickel-free high-nitrogen 19Cr-18Mn-0.69N austenitic stainless steel in 3.5-% NaCl Corrosion
More informationThe Evaluation of Corrosion Behavior of AISI 347 Stainless Steel to ASTM A335 Low Alloy Steel Dissimilar Welds
, pp.14-18 The Evaluation of Corrosion Behavior of AISI 347 Stainless Steel to ASTM A335 Low Alloy Steel Dissimilar Welds I. Hajiannia 1, M.Shamanian 2* and M. Kasiri 3 1,3 Department of Materials Engineering,
More informationCHAPTER 7 STUDIES ON CORROSION RESISTANCE OF STAINLESS STEEL CLADDINGS
134 CHAPTER 7 STUDIES ON CORROSION RESISTANCE OF STAINLESS STEEL CLADDINGS 7.1 INTRODUCTION Corrosion is the destructive result of chemical or electrochemical reactions between a metal or metal alloy and
More informationEFFECT OF COPPER AND COPPER OXIDE ON CORROSION OF BOILER STEEL
06 koperoxide www.hbscc.nl - 1 - EFFECT OF COPPER AND COPPER OXIDE ON CORROSION OF BOILER STEEL W.M.M. HUIJBREGTS Mitteilungen der V.G.B., Vol. 51, No.3, pp. 229-235, June 1971 ABSTRACT Electrochemical
More informationMEASURING THE EFFECTIVENESS OF MIGRATING CORROSION INHIBITORS (MCIs) BY ELECTROCHEMICAL TECHNIQUES
MEASURING THE EFFECTIVENESS OF MIGRATING CORROSION INHIBITORS (MCIs) BY ELECTROCHEMICAL TECHNIQUES By Paul Vrkljan Alla Furman Christophe Chandler Cortec Corporation 4119 White Bear Parkway St. Paul, MN
More informationCross-index of Related Corrosion Standards (Only titles and designations)
Cross-index of Related Corrosion Standards (Only titles and designations) DESIGNATION NACE TITLE PROD # NACE TM0169/ASTM G31 Standard Guide for Laboratory Immersion Corrosion Testing of Metals 21200 NACE/ASTM
More informationMixed potential theory
Mixed potential theory The mixed potential theory consists of two simple hypotheses 1 Any electrochemical reaction can be divided into two or more partial oxidation and reduction reactions. 2 There can
More informationSTRUCTURE AND ELECTROCHEMICAL BEHAVIOUR OF Fe-9Cr-W ALLOYS WITH VARIABLE CARBON AND TUNGSTEN CONTENT. Jiří RAPOUCH, Jaroslav BYSTRIANSKÝ
STRUCTURE AND ELECTROCHEMICAL BEHAVIOUR OF Fe-9Cr-W ALLOYS WITH VARIABLE CARBON AND TUNGSTEN CONTENT Jiří RAPOUCH, Jaroslav BYSTRIANSKÝ Department of Metals and Corrosion Engineering, Institute of Chemical
More informationA Study of Performance of Aluminium Anode by Addition of Zinc in Sea Water
A Study of Performance of Aluminium Anode by Addition of Zinc in Sea Water G.M.Pradeep 1, R.M.Ravindran 2, A.Gokulram 3, R.Rajesh 4, B.YogeshEswaran 5, L. Samson Joshua 6 1 Assistant professor, Dept of
More informationBy: Dr. Irannejad
By: Dr. Irannejad 1 3 1. E.E. Stansbury and R.A. Buchanan, Fundamentals of Electrochemical Corrosion, First edition, 2000. 2. P.R. Roberge, Handbook of Corrosion Engineering, McGraw-Hill, 2000. 3. L.L.
More informationHydrogen Generation During the Corrosion of Carbon Steel in Oxalic Acid (U) B. J. Wiersma WSRC-TR (U)
WSRC-TR-2004-00441 (U) Hydrogen Generation During the Corrosion of Carbon Steel in Oxalic Acid (U) B. J. Wiersma Savannah River National Laboratory Strategic Materials Technology Department Materials Technology
More informationCORROSION OF STEELS IN WATER AND HYDROGEN SULPHIDE
Review of Industrial Engineering Letters 214 Vol. 1, No. 2, pp. 8-88 ISSN(e): 248-9427 ISSN(p): 249-2169 DOI: 1.18488/journal.71/214.1.2/71.2.8.88 214 Conscientia Beam. All Rights Reserved. CORROSION OF
More informationCorrosion Behavior of Mild Steel and SS 304L in Presence of Dissolved Copper
Journal of Minerals & Materials Characterization & Engineering, Vol. 9, No.12, pp.1113-1130, 2010 jmmce.org Printed in the USA. All rights reserved Corrosion Behavior of Mild Steel and SS 304L in Presence
More informationCarbon Effect on pitting of copper tubes, 162, 166, 177, 178 Residue in copper tubes, 156, 157, 163, 174, 175 Calcium, STP576-EB/Feb.
STP576-EB/Feb. 1976 In ex A Aluminum and aluminum alloys, 14, 21-28, 31, 32, 35, 41, 42, 50-54, 62 1100,28,40,43 2024, 26, 28, 32, 37, 40, 43 2219, 40, 43 4043, 62 5052,212-214 5086, 63 5356,63 6061, 23,
More informationEnvironmental Degradation Fundamentals
Environmental Degradation Fundamentals R. G. Ballinger Professor Massachusetts Institute of Technology 1 Outline Thermodynamics of Corrosion: Pourbaix Diagrams Corrosion Kinetics Polarization Diagrams
More informationThe Effect of Calcium Nitrite on the Electrochemical Characterization of 3003 Aluminum Alloys in Sea Water. H.Mogawer and R.Brown
The Effect of Calcium Nitrite on the Electrochemical Characterization of 3003 Aluminum Alloys in Sea Water H.Mogawer and R.Brown Department of Chemical Engineering, University of Rhode Island, Kingston,
More informationModule 5 : Electrochemistry Lecture 25 : Corrosion
Module 5 : Electrochemistry Lecture 25 : Corrosion Objectives After studying this Lecture, you will be able to Outline the electrochemical basis for corrosion. Illustrate the use Pourbaix diagrams Outline
More informationCorrosion Effects of Cr and Ni in Thermo-Mechanical Treated Steel Bar in Marine Environments
Corrosion Effects of Cr and Ni in Thermo-Mechanical Treated Steel Bar in Marine Environments Sunil Kumar Durgam 1, Ghanshyam Das 2, Anjani Kumar Singh 3 1M.Tech, Department of Materials & Metallurgical
More informationTypes of corrosion. 1)Uniform or General Corrosion
Types of corrosion It is convenient to classify corrosion by the forms in which it manifests itself, the basis for this classification being the appearance of the corroded metal. In most cases the naked
More informationSTAINLESS STEEL AND CORROSION
STAINLESS STEEL AND HOW STAINLESS STEEL IS AFFECTED BY, AND RESISTS, steel is the most utilized material of construction. However, natural forces cause steel, an unnatural form of iron, to revert to its
More informationAC : INCORPORATING SUSTAINABILITY ISSUES INTO AN UNDERGRADUATE CORROSION COURSE
AC 2012-4630: INCORPORATING SUSTAINABILITY ISSUES INTO AN UNDERGRADUATE CORROSION COURSE Dr. Harovel G. Wheat, University of Texas, Austin Harovel G. Wheat has a B.A. in Chemistry from University of Colorado,
More informationCOMPARATIVE CORROSION BEHAVIOR OF PURE COPPER AND BRASS IN 3.5% NaCl SOLUTION
COMPARATIVE CORROSION BEHAVIOR OF PURE COPPER AND BRASS IN 3.5% NaCl SOLUTION Lidia BENEA, Eliza DĂNĂILĂ Competences Center: Interfaces-Tribocorrosion-Electrochemical Systems (CC-ITES), Faculty of Engineering,
More informationMMFX 2 (ASTM A 1035, GRADE 100) STEEL REBAR CORROSION PERFORMANCE TESTING IN ACCORDANCE WITH AASHTO MP 18M/MP MMFX Technologies Corporation
MMFX 2 (ASTM A 1035, GRADE 100) STEEL REBAR CORROSION PERFORMANCE TESTING IN ACCORDANCE WITH AASHTO MP 18M/MP 18-09 Prepared for: MMFX Technologies Corporation August 3, 2011 TCG # 11072 Report Prepared
More informationSERBIATRIB th International Conference on Tribology. Kragujevac, Serbia, May 2011
Serbian Tribology Society SERBIATRIB 11 12 th International Conference on Tribology Kragujevac, Serbia, 11 13 May 2011 Faculty of Mechanical Engineering in Kragujevac HEAT EXCHANGER TUBE TO TUBE SHEET
More informationWHAT IS THE ACTUAL COST OF YOUR COMMERCIAL WATER HEATER? LOOKING BEYOND EFFICIENCY INCREASING ROI THROUGH WATER HEATER MATERIAL SELECTION
Engineered Water Heating Solutions WHAT IS THE ACTUAL COST OF YOUR COMMERCIAL WATER HEATER? LOOKING BEYOND EFFICIENCY INCREASING ROI THROUGH WATER HEATER MATERIAL SELECTION Water Heater Efficiency Water
More informationCorrosion inhibition of 316L stainless steel in plain tap water
International Journal of Chemistry and Material Science Vol. 2(4), pp. 068-073, November 2014 Available online at http://academeresearchjournals.org/journal/ijcms ISSN 2327-5553 2014 Academe Research Journals
More informationBiological Corrosion Failures
Biological Corrosion Failures Thomas R. Jack, NOVA Chemicals Ltd. MICROORGANISMS can directly or indirectly affect the integrity of many materials used in industrial systems. Most metals, including iron,
More informationCORROSION TYPES CHAPTER 4 6) FILIFORM CORROSION LECTURER SAHEB M. MAHDI
CORROSION TYPES CHAPTER 4 6) FILIFORM CORROSION LECTURER SAHEB M. MAHDI 5 ) Filiform corrosion: Filiform corrosion is a type of localized corrosion that is often associated with aluminum and magnesium
More informationPerformance of Nickel-Coated Manganese Steel in High-Chloride Low-Sulphate Seawater Environments
Journal of Minerals & Materials Characterization & Engineering, Vol. 9, No.10, pp.879-886, 2010 jmmce.org Printed in the USA. All rights reserved Performance of Nickel-Coated Manganese Steel in High-Chloride
More information