EDELSTAHL WITTEN-KREFELD GMBH THYRAPID. Tool steels THYRAPID THYRAPID THYRAPID THYRAPID THYRAPID. High-Speed Steels
|
|
- Sabina Austin
- 6 years ago
- Views:
Transcription
1 EDELSTAHL ITTEN-KREFELD GMBH Tool steels High-Speed Steels
2 3202 ode T 15 r o Heavy-duty, high-speed steel grade with maximum cutting-edge endurance and wear resistance due to its high content. The o content additionally lends it high red hardness and resistance to. Machining of hard materials that wear the cutting edges, e.g. highly quenched and tempered r-ni steel grades and non-ferrous metals, as well as mother-of-pearl, paper, hard rubber, synthetic resins, marble, slate and the like. Ideally suited to turning tools and forming tools of all kinds, finishing tools, heavy-duty milling cutters or automatic lathe tools. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
3 3207 ode T 42 r o Extremely high-performance, high-speed steel grade that combines optimum cutting-edge endurance, high-temperature strength and toughness owing to its. Universally suitable for roughing or finishing work where maximum tool life is required, for large-batch automatic lathe work, all kinds of cutting tools and extremely highly stressed milling cutters. Soft annealing max. 300 Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
4 3243 ode M35 r o This steel grade is also available with a higher S content (S = 0.10%) under the name 3245, M 35 + S, The o content of this tough, high-performance, high-speed steel grade, which offers good cutting-edge endurance, results in high red hardness and resistance to. onsequently, this steel grade is particularly suitable when thermal stresses and discontinuous cutting are involved. Heavy-duty milling cutters of all kinds, highly stressed twist drills and taps, profiled cutting blades, machining of high-strength materials, broaches. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
5 3245 ode M 35 + S r o S Tough, high-performance, high-speed steel grade with good cutting-edge endurance, high red hardness and resistance to. Same basic as 3243, but with higher S content to improve cutting properties and suitability for relief-turning. Heavy-duty milling cutters of all kinds, particularly for relief-turned and relief-ground hobs, chasers and segments for circular saws. Machining of high-strength materials. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
6 3247 ode M 42 r o High-carbon, high-speed steel grade based on, with high resistance to wear, red hardness and toughness. This steel grade displays good grindability as a result of its low content. Tools subject to severe mechanical wear, e.g. in cases of small cross-section cuts and high cutting speeds. Particularly suitable for die-sinking cutters and one-lip cutters, and for tool bits in automatic lathes. Also suitable for non-cutting applications, e.g. cold extrusion rams, and for tools for machining aircraft materials, such as titanium alloys, etc. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
7 3341 ode M 2 + S r S Same basic as 3343, but with a higher S content to improve cutting properties and suitability for relief-turning. Milling cutters of all kinds, particularly relief-turned and relief-ground hobs, chasers and segments for circular saws. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
8 3343 ode M r 1.9 This steel grade is also available with an elevated S content (S = 0.12%) under the name Thyrapid Standard high-speed steel grade. High toughness and good cutting power owing to its well-balanced alloy, making it suitable for a wide variety of applications. Physical properties Thermal conductivity /(m K) For all metal-cutting tools for roughing or finishing, such as twist drills, all kinds of milling cutters, screw taps, screw dies, broaches, reamers, countersinks, chasers, segments for circular saws, shaping tools and woodworking tools. Also highly suitable for cold-forming tools, such as cold extrusion rams and dies, as well as for cutting and precision cutting tools, plastics moulds with elevated wear resistance and screws. Soft annealing Hardening Quenching circulaing furnace b) 850 and a) arm bath 550 b) Oil c) Air At least twice ontinuous time-temperature-transformation diagram Temperature in in Austenitising Austenitisierungstemperatur temperature Ac 1e Start Umwandlungsbeginn of transformation 800 Ac 1b End 31 Umwandlungsende of transformation Pearlite Perlitstufe stage Start Beginn of der carbide Karbidausscheidung precipitation Austenite + arbide Karbid Ledeburit + Ledeburite 400 Start Umwandlungsbeginn of transformation 300 = Härtewerte Hardness in 53 50% 200 Zwischenstufe Bainite stage % Martensite Martensitstufe stage 65 80% Zeit Time in in s s Zeit in min Time Zeit in h Hardness in Härte in diagram Anlasstemperatur temperature in in
9 3344 ode M3/2 r Same basic as 3343, but with substantially higher and content. This steel grade thus combines maximum wear resistance, maximum cutting-edge endurance and good toughness. Screw taps, reamers, heavy-duty milling cutters, screw dies, shaper cutters and rotary shaving cutters for machining hard materials, socket-head and round-hole punching dies for manufacturing nuts. Soft annealing Hardening from in a) arm bath 550/Air or The hardening temperatures apply to salt-bath hardening. A reduction of 10 to 30 is recommended for vacuum hardening.
STEELS & COATINGS FOR CUTTING TOOL APPLICATIONS
STEELS & COATINGS FOR CUTTING TOOL APPLICATIONS Requirements for cutting tools There are several characteristics that are essential to the good performance of a cutting tool. Powder Metal High Speed Steels
More informationThe Convenience Stores For Metal
TOOL STEEL SELECTOR GUIDE Application Suggested Grades Arbors... O1, A2, A6 Battering Tools... S5, S1, S7 Blacksmith Tools... S5, S1 Boiler-Shop Tools... S5, S1, S7 Bolt Clippers... S5, S1 Boring Tools...
More informationMSE-226 Engineering Materials
MSE-226 Engineering Materials Lecture-7 ALLOY STEELS Tool Steels TYPES of FERROUS ALLOYS FERROUS ALLOYS Plain Carbon Steels Alloy Steels Cast Irons - Low carbon Steel - Medium carbon steel - High carbon
More informationTOOL STEEL. Tool Steel VJ-04/2015. Copyright 2015 by Vojay LLP, United Kingdom.
www.vojaygroup.com VJ04/2015. Copyright 2015 by Vojay LLP, United Kingdom. Heat treatment requirements High Speed & Die General description Tool steel refers to a variety of carbon and alloy steels that
More informationAISI A2 Cold work tool steel
T OOL STEEL FACTS AISI A2 Cold work tool steel Great Tooling Starts Here! General AISI A2 is an air- or oil hardening chromiummolybdenum-vanadium alloyed tool steel characterized by: Good machinability
More informationHIGH SPEED TOOL STEELS
1 1 1 1 1 1 1 1 1 1 1 SEAVANS North Bldg. 2-1, Shibaura 1-chome, ato-ku Tokyo 105-8614, Japan Specialty Steel Company. Tel.+81-3-5765-4410 Fax.+81-3-5765-8317 2 Manhattanville Road, Suite 301, Purchase,
More informationPLASTIC MOULD STEEL M340 BÖHLER. voestalpine BÖHLER Edelstahl GmbH & Co KG BÖHLER KUNSTSTOFFFORMENSTAHL
PLASTIC MOULD STEEL BÖHLER M340 voestalpine BÖHLER Edelstahl GmbH & Co KG www.voestalpine.com/bohler-edelstahl BÖHLER KUNSTSTOFFFORMENSTAHL EXACTLY TO YOUR LIKING An increase in productivity in high-tech
More informationspecial hot work tool steel CR7V-L
special hot work tool steel CR7V-L T h e p r e m i u m s t e e l w i t h m a x i m u m h i g h t e m p e r at u r e w e a r r e s i s ta n c e 2 From the casting of steel to finished die... LONG-STANDING
More informationMATERIALIZING VISIONS. Bohler-Uddeholm M42 HIGH SPEED STEEL
MATERIALIZING VISIONS Bohler-Uddeholm M42 HIGH SPEED STEEL General Cobalt-alloyed, molybdenum high speed steel possessing high hardness, excellent cutting properties, exceptional compressive strength,
More informationRAMAX 2. Prehardened stainless holder steel
RAMAX 2 Prehardened stainless holder steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be
More informationHOTVAR. Hot work tool steel
Hot work tool steel General HOTVAR is a high performance molybdenumvanadium alloyed hot-work tool steel which is characterized by: High hot wear resistance Very good high temperature properties High resistance
More informationUddeholm Formvar. FORMVAR is a trade mark registered in the European Union
Uddeholm Formvar FORMVAR is a trade mark registered in the European Union UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright
More informationHOTVAR Hot work tool steel
T OOL STEEL FACTS HOTVAR Hot work tool steel Wherever tools are made Wherever tools are used General HOTVAR is a high performance molybdenumvanadium alloyed hot-work tool steel which is characterized by:
More informationUddeholm Vanadis 30 SuperClean. Uddeholm Vanadis 30 SuperClean
Uddeholm Vanadis 30 SuperClean 1 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based
More informationD101 - JOBBER DRILLS - Silver Bullet
D101 - JOBBER DRILLS - Silver Bullet Sutton Tools Silver Bullet jobber drills are a general purpose drill bit designed for machine and hand held drilling in a wide range of ferrous & non-ferrous materials
More informationAISI D2 Cold work tool steel
T OOL STEEL FACTS AISI D2 Cold work tool steel Great Tooling Starts Here! This information is based on our present state of knowledge and is intended to provide general notes on our products and their
More informationVANADIS 6 SuperClean
T O O L S T E E L F A C T S SuperClean High performance powder metallurgical cold work tool steel Great Tooling Starts Here! Cover photo: Powder pressing punch of. Excellent results have been obtained
More informationTool steel. SCHMOLZ + BICKENBACH Distributions GmbH. Eupener Str. 70 D Düsseldorf
Tool steel SCHOLZ BICKENBACH Distributions GmbH Eupener Str. 7 D-49 Düsseldorf www.schmolz-bickenbach.de Werkzeugstahl_GB.qxd:Layout 1 1.7.8 1:14 Uhr Seite Customized quality-tested tool steel solutions
More informationEAF. Ladle Furnace. Continuous Casting. Conventional Casting. Remelting VAR and ESR. Reheating Furnace. Open Die. Mill. Bar/Coil Finish Rolling Mill
TOOL STEELS Conventional Casting EAF Ladle Furnace VD Continuous Casting MANUFACTURING PROCESSES FOR CONVENTIONAL AND REMELTED STEELS MELT SHOP Melting Process (Conventional): EAF (Electric Arc Furnace)
More informationVANADIS 10 SuperClean High performance powder metallurgical cold work tool steel
SuperClean High performance powder metallurgical cold work tool steel Critical tool steel properties for GOOD TOOL PERFORMANCE Correct hardness for the application Very high wear resistance Sufficient
More informationCALMAX. Plastic mould and cold work steel
Plastic mould and cold work steel General CALMAX is a chromium-molybdenum-vanadium alloyed steel characterized by: High toughness Good wear resistance Good through hardening properties Good dimensional
More information> RX12UF. Cobalt content w/w. Grade. Properties and recommendations. HARTMETALL ESTECH AG 6285 Hitzkirch
pli > Ultra-fine grain carbides are characterized by a very high hardness and wear resistance. They are used for milling tools and drills for processing abrasive, soft and tough materials, in nozzles and
More informationUDDEHOLM VIDAR 1 ESR
UDDEHOLM VIDAR 1 ESR This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationSANDVIK FINEMAC FREE- CUTTING WIRE WIRE
SANDVIK FINEMAC FREE- CUTTING WIRE WIRE DATASHEET Sandvik Finemac is a lead-free, hardenable, free-cutting carbon steel characterized by excellent machinability and high hardness, high wear resistance
More informationBy combining Uddeholm Ramax HH with one of our other products within the Stainless Concept, you can create a completely stainless mould.
UDDEHOLM RAMAX HH Uddeholm Ramax HH provides several benefits: The product offers uniform hardness in all dimensions combined with excellent indentation resistance. It is a corrosion resistant grade which
More informationUDDEHOLM VIDAR 1 ESR
UDDEHOLM VIDAR 1 ESR This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationEdition 3, The latest revised edition of this brochure is the English version, which is always published on our web site
This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties
More informationTOOL STEEL SUPER SQUARE HEAT TREATING Notes thru TOOL WRAP GRADE AVAILABILITY
TOOL STEEL COLD WORK TECHNICAL INFORMATION AISI A2... 14-2 AISI A6... 14-3 AISI D2... 14-4 AISI DC53... 14-5 AISI O1... 14-6 AISI O6... 14-7 AISI L6... 14-8 AISI S5... 14-9 AISI S7... 14-10 AISI S7 ESR...14-11
More informationBorn from fire, made to endure MOULD STEELS TOOL STEELS FOR PLASTIC MOULDING
Born from fire, made to endure MOULD STEELS TOOL STEELS FOR PLASTIC MOULDING IN TODAY'S GLOBAL PRODUCTION OF PLASTIC PRODUCTS THERE ARE DIFFERENT TECHNOLOGICAL PROCESSES, AMONG WHICH THEY ARE THE MOST
More informationHOLDAX Prehardened holder steel
Prehardened holder steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationPLASTIC MOULD STEEL RS 100
PLASTIC MOULD STEEL RS 100 PLASTIC MOULD STEEL Family of RS plastic mould steel RS grade W.Nr. DIN AISI RS 100 1.2312 40CrMnMoS8-6 ~P20 RS 101 1.2311 40CrMnMo7 ~P20 RS 103 1.2738 40CrMnNiMo8-6-1 RS 105
More informationIMPAX SUPREME. IMPAX Prehardened mould steel
IMPAX SUPREME IMPAX Prehardened mould steel 1 Edition: 4, 11.2003 No. 031101 This information is based on our present state of knowledge and is intended to provide general notes on our products and their
More informationORVAR SUPREME. Hot work tool steel
Hot work tool steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationIMPAX SUPREME Prehardened mould steel
T OOL STEEL FACTS IMPAX Prehardened mould steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is intended to provide general notes on our
More information11.3 The alloying elements in tool steels (e.g., Cr, V, W, and Mo) combine with the carbon to form very hard and wear-resistant carbide compounds.
11-2 11.2 (a) Ferrous alloys are used extensively because: (1) Iron ores exist in abundant quantities. (2) Economical extraction, refining, and fabrication techniques are available. (3) The alloys may
More informationUddeholm Formax. Formax is a trademark registered in Sweden
Uddeholm Formax Formax is a trademark registered in Sweden UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder.
More information1 Cutting Tool Materials of common use
1 Cutting Tool Materials of common use Instructional Objectives At the end of this lesson, the students will be able to (i) Identify the needs and cite the chronological development of cutting tool materials.
More informationUddeholm Dievar is a specially developed steel grade by Uddeholm, which provides the best possible performance.
UDDEHOLM DIEVAR Uddeholm Dievar is a specially developed steel grade by Uddeholm, which provides the best possible performance. The chemical composition and the very latest in production technique make
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM VANADIS 60 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationDAYE JINGCHENG MOULD CO., LTD TOOL STEEL PRODUCT
1.2343 Hot Work Tool Steel Identification Designation by Standards Mat. No. DIN EN AISI 1.2343 X38CrMoV51 X38CrMoV51 H11 Chemical Composition C Si Mn Cr Mo V P S 0.36 0.90 0.30 4.80 1.10 0.25 0.030 0.030
More informationGeneral. Properties Physical data. Applications. Compressive strength. Corrosion resistance
UDDEHOLM ELMAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationC S max Mn Cr Mo V Other element Ti. Young modulus (GPA)
Industeel Tenasteel Tenasteel : a cold work tool steel, combining a high compression strength and a very good toughness. Its other advantages are a particularly high resistance to thermal softening and
More informationCountersinks. Smooth cutting, perfect chamfering - Counterbores - Cross Hole - Single Flute - Three Flute
Countersinks Countersinks Smooth cutting, perfect chamfering - Counterbores - Cross Hole - Single Flute - Three Flute smooth cutting perfect chamfering countersinks Product Code: C108 This new generation
More informationUDDEHOLM RAMAX LH. Uddeholm Ramax LH is a part of the Uddeholm Stainless Concept.
UDDEHOLM RAMAX LH TAKING STANDARDS TO A NEW LEVEL Setting standards is important in the tooling industry. Uddeholm Ramax LH is no exception. It is a first class tool steel for mould bases, with excellent
More informationUddeholm Holdax. Classified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets.
Uddeholm Holdax UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present state
More informationCryogenic Technique for the Steel Heat Treatment
International Journal of Scientific & Engineering Research, Volume 4, Issue 8, August 2013 Cryogenic Technique for the Steel Heat Treatment Sanjay Murari, Sunil Bhujangannavar Abstract Considering the
More informationSpecial Steels for Precise Die and Mold
DURO for Cold Work Special Steels for Precise Die and Mold R For Cold Work High Toughness Grades High Wear Resistance Grade DURO-Created by NACHI s original technology Steels with superior balance of toughness
More informationUDDEHOLM VANCRON 40 SS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM VANCRON 40 Uddeholm Vancron 40 is a nitrided powder tool steel, which means that a surface coating is already integrated into the finished tooling material. The result is a tool surface with very
More informationVBN Components AB. 3D-printing for demanding applications. ESS, Max IV, IUC Syd/Big Science Dk Lund,
VBN Components AB 3D-printing for demanding applications ESS, Max IV, IUC Syd/Big Science Dk Lund, 2017-09-19 Ulrik Beste CTO, VBN Componens AB ulrik.beste@vbncomponents.com 070 235 86 26 VBN Components
More informationHigh-Quality Tool Steel Hot-Work Steels
High-Quality Tool Steel Hot-Work Steels Hot-forming tools are needed for chipless forming of workpieces from iron and non-ferrous materials and their alloys as well as the production of articles of daily
More informationSandvik Hyperion Metal Cutting. Gear Cutting Applications
Sandvik Hyperion Metal Cutting Gear Cutting Applications Hob Blanks Standard Hob blanks available with 12 teeth or 15 teeth configuration. Sandvik Hyperion Benefits: Reduction in EDM wire cutting - reduces
More informationNEW BÖHLER POWDER METALLURGY HIGH SPEED STEEL WITH EXCELLENT HOT HARDNESS
NEW BÖHLER POWDER METALLURGY HIGH SPEED STEEL WITH EXCELLENT HOT HARDNESS I. Maili, R. Rabitsch, W. Liebfahrt, H. Makovec and E. Putzgruber BÖHLER EDELSTAHL GMBH & Co KG Mariazellerstr. 25 A 8605 Kapfenberg
More informationHeat Treatment of Steels
Heat Treatment of Steels Heat Treating is the process of heating and cooling a steel to obtain desired properties. Various types of heat treatment processes are used to change the following properties
More informationUDDEHOLM VANADIS 23 SUPERCLEAN
UDDEHOLM VANADIS 23 SUPERCLEAN UDDEHOLM VANADIS 23 SUPERCLEAN Uddeholm Vanadis 23 SuperClean is a high alloyed powder metallurgical high speed steel corresponding to AISI M3:2 with a very good abrasive
More informationC45 / TS Average Chemical analysis. Steel properties. Standards. Heat treatment. Applications. C% Si% Mn%
C45 / TS 1730 C% Si% Mn% 0.45 0.20 0.70 680 710 approx. 6 800 830 Water 57 max. 207 Hardness after quenching 57 49 3 Shell-hardenable steel featuring hard surface and tough core. AISI 1045 Components for
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM FORMAXTM This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM ALVAR 14 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationHeat Treatment of Steels
Heat Treatment of Steels Heat Treating is the process of heating and cooling a steel to obtain desired properties. Various types of heat treatment processes are used to change the following properties
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM HOLDAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationExcellent stability und. ARNO SHORT-Cut -SIS. w w w. a r n o. d e. Introducing SHORT-Cut -SIS for internal groove turning. The new SHORT-Cut holder
Introducing SHORT-Cut -SIS for internal groove turning New w w w. a r n o. d e The new SHORT-Cut holder with optimum insert clamping. Easy handling and efficient in production. ARNO SHORT-Cut -SIS Excellent
More informationTOOLMAKER SOLUTIONS Custom-Made Inserts Blanks
Non-ISO carbide insert blanks for threading, parting, grooving, drilling, reaming and milling applications TOOLMAKER SOLUTIONS Custom-Made Inserts Blanks HYPERION CUSTOM-MADE INSERT BLANKS Hyperion manufacturers
More informationPRELIMINARY BROCHURE. Uddeholm Vanadis 8 SuperClean
PRELIMINARY BROCHURE Uddeholm Vanadis 8 SuperClean UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information
More informationDC53. Rev o lu tion. Medium Chrome Tool Steel
DC53 Medium Chrome Tool Steel The High Performance Alternative for: Punches & Dies Draw & Form Dies Shear Blades Shredder Knives Thread & Form Rolls Cold Heading Dies Mill Rolls & Slitters Rev o lu tion
More informationHigh strength low alloy (HSLA).
7 Alloy Steels High strength low alloy (HSLA). a type of steel alloy that provides many benefits over regular steel alloys contain a very small percentage of carbon (less than one-tenth of a percent) and
More informationPLASTIC MOULD STEEL M390 BÖHLER. voestalpine BÖHLER Edelstahl GmbH & Co KG
PLASTIC MOULD STEEL BÖHLER M390 voestalpine BÖHLER Edelstahl GmbH & Co KG www.voestalpine.com/bohler-edelstahl BENEFIT IN RESPECT OF VERSATILITY AND PERFORMANCE BÖHLER M390 MICROCLEAN is a martensitic
More informationBFF1113 Engineering Materials DR. NOOR MAZNI ISMAIL FACULTY OF MANUFACTURING ENGINEERING
BFF1113 Engineering Materials DR. NOOR MAZNI ISMAIL FACULTY OF MANUFACTURING ENGINEERING Course Guidelines: 1. Introduction to Engineering Materials 2. Bonding and Properties 3. Crystal Structures & Properties
More informationPRELIMINARY BROCHURE. Uddeholm Caldie
PRELIMINARY BROCHURE Uddeholm Caldie UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based
More informationVanax SuperClean. Uddeholm Vanax SuperClean
Vanax SuperClean Uddeholm Vanax SuperClean ASSAB is a trademark of voestalpine High Performance Metals Pacific Pte Ltd. The information contained herein is based on our present state of knowledge and is
More informationFACTFILE: GCE TECHNOLOGY & DESIGN
FACTFILE: GCE TECHNOLOGY & DESIGN 1.3 METAL PART 1 Metal Part 1 Learning outcomes Students should be able to: Demonstrate knowledge of the available form of supply of metals; Understand the difference
More informationUddeholm Vanadis 23 SuperClean
Uddeholm Vanadis 23 SuperClean Uddeholm Vanadis 23 SuperClean Uddeholm Vanadis 23 SuperClean is a high alloyed powder metallurgical high speed steel corresponding to AISI M3:2 with a very good abrasive
More informationMADE IN AUSTRIA HIGH SPEED STEEL. Quality is our Passion. voestalpine BÖHLER Edelstahl GmbH & Co KG
MADE IN AUSTRIA HIGH SPEED STEEL Quality is our Passion voestalpine Edelstahl GmbH & Co KG www.voestalpine.com/bohler-edelstahl HIGH PERFORMANCE MATERIALS FOR HIGH PERFORMANCE TOOLS SPEED SKILLS voestalpine
More informationREGIN 3. Cold work tool steel
Cold work tool steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUddeholm Sverker 3. Classified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets. Edition 8, 06.
Uddeholm Sverker 3 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present
More informationSpheroidal Graphite (Nodular) Cast Iron:
Product Type Grade of Product Sub Grade SG Iron Pearlitic Accicular Adamite Steel Based Alloy Steel Solid Rolls Graphitic IC Rolls DP Rolls SG Core G I Core ACCI Rolls Spheroidal Graphite (Nodular) Cast
More informationHARDFACING ELECTRODES
HARDFACING ELECTRODES UTOP 38.. K1 UTOP 43.. K2 UTOP 45.. K3 UTOP 52.. K4 UTOP 55.. K5 TOOLDUR... K6 E DUR 250... K7 E DUR 300 K8 E DUR 400... K9 E DUR 500 K10 E DUR 600 K11 E DUR 60R. K12 E DUR 600Si..
More informationSUPERIOR MACHINABILITY
Uddeholm Balder Uddeholm Balder Reliable and efficient steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters
More informationHOT WORKING TOOL STEELS
HOT WORKING TOOL STEELS 1 Characteristics of YSS Hot Work Tool Steels Warm forging 56~58HRC Precision hot forging 47~56HRC High temperatrure strength, Wear resistance High speed hot forging 47~54HRC F
More information021 COUNTERBORES 055 MASONRY
010 BUTT WELDED TOOLS 016 DIE HEADS & CHASERS 017 THREAD RESTORERS Page...........................32 Page...........................33 Page...........................33 019 SHEET & TUBE DRILLS 020 COUNTERSINKS
More informationAPM 2730 HOT ISOSTATIC PRESSED (HIP) PRODUCTS
APM 2730 HOT ISOSTATIC PRESSED (HIP) PRODUCTS DATASHEET APM 2730 is a high alloyed powder metallurgical high speed steel corresponding to ASTM M3:2 +Co with a combination of very good abrasive wear resistance,
More informationSpecial Tool Configurations
Special Tool Configurations Special Overall and/or Flute Lengths While we recoend using a standard overall and flute length whenever possible, there are situations where the use of special overall and/or
More informationCORRAX A stainless precipitation hardening steel
T OOL STEEL FACTS PRELIMINARY BROCHURE CORRAX A stainless precipitation hardening steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is
More informationThe name you can trust HOT WORK TOOL STEEL RAVNEX DC
The name you can trust HOT WORK TOOL STEEL RAVNEX DC RAVNEX DC CONTENTS GENERAL CHARACTERISTICS 02 Chemical composition Application Microstructure in delivered condition Toughness Qualitative comparison
More informationExperiment E: Martensitic Transformations
Experiment E: Martensitic Transformations Introduction: The purpose of this experiment is to introduce students to a family of phase transformations which occur by shear rather than diffusion. In metals,
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM UNIMAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationSmall but Powerful Positive Insert with Dovetail Design
1/9 Small but Powerful Positive Insert with ovetail esign 2/9 Small but Powerful Positive Insert with ovetail esign TaeguTec is proud to introduce a brand new product line to its popular CHASEMI family.
More informationRigor is a trade mark registered in the European Union and in the U.S.
UDDEHOM RIGOR Rigor is a trade mark registered in the European Union and in the U.S. This information is based on our present state of knowledge and is intended to provide general notes on our products
More informationQRO 90 SUPREME Hot work tool steel
T O O L S T E E L F A C T S QRO 90 Hot work tool steel Great Tooling Starts Here! Cover photo: Bo Dahlgren This information is based on our present state of knowledge and is intended to provide general
More informationNew XEVT Line for Excellence in Aluminum Machining
1/14 New XEVT ine for Excellence in Aluminum Machining 2/14 To ensure excellence in aluminum machining across all industries, TaeguTec s CHASEAU line now comes in two new offerings: the XEVT 16 which is
More informationHSS rolled. HSS ground. HSS Co 5 ground. HSS-TiN ground. Twist drills DIN 338 type N. Point cuts:
Twist drills DIN 338 type N High performance twist drill suitable for all normal drilling in conventional materials. Point cut: helical point Helix angle: 20-30 tolerance: h8 Right-hand cutting 1,0 up
More informationUDDEHOLM QRO 90 SUPREME
UDDEHOLM QRO 90 SUPREME This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationSpecial pre-hardened tool steel for Plastic Moulds: GSF ESR
Special pre-hardened tool steel for Plastic Moulds: GSF ESR Special tool steel for Plastic Moulds GSF ESR Premium tool steel with firm and secured tool properties are exemplified by excellent high gloss
More informationMilling tools made by JONGEN! C10 FP 124. Face Milling
Milling tools made by JONGEN! Face Milling C10 FP 124 THE TOOL Especially efficient face milling cutter for the roughing and finishing machining Axial depth of cut max. 5 mm, with 8 effective cutting edges
More informationVANADIS 4 EXTRA VANADIS 4 EXTRA
uddeholm REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42 D2 1.2379
More informationCoating and Reconditioning Services
The Tool Company TWIST DRILLS REAMERS DIAMOND TOOLS TAPS END MILLS MODULAR TOOL SYSTEMS RECONDITIONING & COATING Coating and Reconditioning Services Guhring s Reconditioning Division turns worn cutting
More informationis detrimental to hot workability and subsequent surface quality. It is used in certain steels to improve resistance to atmospheric corrosion.
Glossary of Terms Alloying Elements ALUMINIUM - Al is used to deoxidise steel and control grain size. Grain size control is effected by forming a fine dispersion with nitrogen and oxygen which restricts
More informationTOOL AND DIE STEELS. Ameralloy -7 Ameralloy -13 Ameralloy -20 Amera-Mold Ameralloy -6 Ameralloy -FH Ameralloy High Speed-2 Ameralloy-T Durelloy-PM
TOOL AND DIE STEELS Ameralloy Oil Ameralloy Air Ameralloy -0 Ameralloy D- Amera-Graf Ameralloy W & W Ameralloy Drill Rods Ameralloy Precision Flat Ground Ameralloy - Ameralloy -7 Ameralloy - Ameralloy
More informationASSAB M UDDEHOLM ORVAR 2 MICRODIZED
ASSAB 8407 2M UDDEHOLM ORVAR 2 MICRODIZED REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER
More informationFormadur PH X Superclean The corrosion-resistant steel that sets polishability standards
Formadur PH X Superclean The corrosion-resistant steel that sets polishability standards PLASTIC MOULD MANUFACTURING S GEM Plastic mould manufacturing s gem The current tendency in plastic mould manufacturing
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM SVERKER 3 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More information