Maximum Rust Protection!
|
|
- Martin Sharp
- 6 years ago
- Views:
Transcription
1 ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric ability is extraordinary. Steel is isolated from the electrolysis process that converts steel to rust. Zero Rust has many superior traits. The first is it provides maximum adhesion to steel, this is called chemical affinity. The second is its ability to create a dielectric barrier to isolate the steel from electrolysis process which converts steel to rust. If you starve the oxygen from the substrate, oxidation cannot occur. Testing: Zero Rust exceeded 2000 hours at 3.5 mils dry film thickness in the ASTM-B117 salt spray tests. Other popular primers test out at around 250 to 350 hours in side by testing. The effectiveness of Zero Rust on bare steel surfaces is optimized at 3.0 to 3.5 mils dry film thickness. Zero Rust Color Selection: Red Oxide 60 Gray 61 Black 62 Cat Yellow 63 White 67 Blue 68 Green 70 Safety Yellow 71 Safety Red 72 Tan 95
2 Surface Preparation: Thoroughly clean all surfaces of any dirt, oil, grease, silicone and any other contaminants with Prep-Step. Remove all loose rust. Time spent on surface preparation with greatly improve product performance. New Steel: Remove mill scale before applying Zero Rust. Any mill scale left intact will become the weak link in the system. Rusty Surfaces: Work down rusty surfaces with two goals in mind: 1 st Remove all loose scale and powdery dust. The key is to minimize air entrapment in the substrate. Leave no oxygen behind to continue the rusting process. 2 nd Remove as much pitting as possible. The smoother the surface and the tighter the remaining rust, the less product you will need to span the highs and lows to achieve the 3.0 to 3.5 mil coverage. Heavy rust scale can be softened for easier removal with the use of Zero Rust Prep-Step Partially Rusted, Partially Painted Surfaces: When repairing a painted surface that has deteriorated, total removal of old paint is preferred. When this is not feasible, treat surface as you would mil scale from the standpoint that old paint becomes the weak link in the system. The cleaner and tighter the surface, the better the results for your paint job. Painted edges can have the tendency to curl and a rotary sander will feather them out.
3 Surface Preparation: Galvanized Steel: Aged rough galvanized steel needs to be cleaned and then coated with Zero Rust Addition of either one teaspoon of dry Portland Cement or One half teaspoon of highhydrated lime per gallon of Zero Rust For new galvanized steel, use a vinyl wash primer before applying Zero Rust The dry mil thickness of the wash primer should not exceed ½ mil. Thinning: Zero Rust is a heavy bodied primer and thinning might be needed. There are many types of spray equipment on the market today. if you do find the need to thin you will need to use a EPA approved VOC compliant thinner for your area. We recommend a reduction of no more than 15-25%. Do not thin with mineral spirits or VMP. When using airless spray equipment no thinning is normally needed. You will need to thin to suit for brush or roller applications. Remember that if you thin Zero Rust additional wet film thickness will be required to achieve a dry mil of 3.0 to 3.5. Application: Mix well before using and box paint if multiple gallons are to be used. Apply with spray gun, brush or roller. For best results apply a minimum of two coats, using a crosshatch pattern from one coat to the next coat. The first coat should be about 3 mils wet (1.5 mils dry), to assure adequate coverage. An easy visual barometer is to use two dissimilar colors for the two coats. Use a red coat first then come back with a black coat to achieve total coverage. Allow 20 to 30 minutes between coats. Do not apply too heavy because flash time will increase. This is extremely important because Zero Rust is formulated to be impermeable to oxidation, thus a heavy coat will need much more time to cure. Use of a wet mill gauge is highly recommended to insure proper film mils
4 Dry Time: Zero Rust dries to touch in 30 minutes and is tack free within one hour, depending on the relative humidity and temperature. Dry time can also be affected by film thickness, flash off time between coats, amount of thinning, air movement and temperature. Temperature Range: Zero Rust can withstand intermittent temperatures of Heat resistance will vary by color. Topcoats: Zero Rust is compatible with a wide variety of commercial topcoats. Commercial topcoats may be applied within 24 hours or after solvents have evaporated. As it is impossible to cover all the topcoats on the market, you will need to do a test panel to determine compatibility and dry time window for your selected topcoats. Two-component automotive urethanes that are acetone-free and contain high solids can be used successfully. Urethanes that contain acetones will require more precise timing to topcoat. A 4 mil wet film of Zero Rust can be top coated within three to six hours with minimal solvent trap problems. If you cannot apply the topcoat within this time frame, it is advisable to wait 24 hours before top coating. Applying a light first coat of urethane is recommended. Cleanup and Waste Disposal: Use EPA VOC complaint MEK, xylene or lacquer thinners for clean up. Dispose of waste and residue in accordance with regulations applicable to the area of use.
5
6 14 years and still performing!
7 What Zero Rust Can Do For You! Remember, don t just cover your rust --- STOP Your Rust with ZERO RUST!!
Refer to Substrates & Surface Preparation.
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance
More informationRust Bullet Home and Farm FAQ s
Rust Bullet Home and Farm FAQ s 1. Will Rust Bullet Protect My Galvanized Metal Roof? Yes. Rust Bullet is the ideal coating for protecting sheet metal buildings and roofs; it not only provides protection
More informationPRODUCT GUIDE: ZINC-RICH COATINGS. Version:
PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,
More informationAliphatic Acrylic-Polyester Polyurethane
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance
More informationCarboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial
More informationRUST TRAP TECHNICAL DATA SHEET
RUST TRAP TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rust Trap is a high gloss, moisture cured, urethane coating for restoring and protecting rusty metal. FEATURES Premium moisture-cured urethane
More informationRUST TRAP TM TECHNICAL DATA SHEET
RUST TRAP TM TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rust Trap is a moisture cross- linked urethane for coating ferrous metals. Rust Trap also adheres to aluminum, fiberglass and properly prepped
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators
Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators GENERAL DESCRIPTION A high solids, two component, high build, VOC conforming (2.1 lbs./gal.) Low HAPS
More informationProduct Information CHEMGLAZE B 9942 A/B. Coating for Casting Pits. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces.
Product Information Chemical Products Division CHEMGLAZE B 9942 A/B Coating for Casting Pits. FEATURES BENEFITS. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces. Will build to
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer
Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy
More informationVapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring
advanced moisture control, inc. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring 250 polished concrete slabs! Made in Southern California,
More informationCorlar LV PR 178 Series Epoxy Primer
Corlar LV PR 178 Series Epoxy Primer GENERAL DESCRIPTION A two-component very low VOC corrosion-resistant epoxy primer designed to be extremely tough and durable. When properly activated, the combined
More information1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)
DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant
More informationBEP Blue Barrier Installation and Application Guide
BEP Blue Barrier Installation and Application Guide BEP Blue Barrier is a system of seamless fluid applied products designed to protect the building envelope. Approved assemblies and applications listed
More informationNFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings
NFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings 1 Scope The application of mastic and thin-film intumescent fire resistive coatings
More information- Aromatic hydrocarbons - Binder 2,67 kg/dm³ (±0,06 Kg/dm³) Solid content - 80% by weight (±2%) - 58% by volume (±2%) according to ASTM D2697
p. 1/6 ZINGA The Film Galvanising System ZINGA is a one pack coating that contains 96% zinc in the dry film and provides cathodic protection of ferrous metals. It can be used as a unique system as an alternative
More informationGeneral Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.
General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound.
More informationGRIP-GARD PLUS BRUSH / ROLL ADDITIVE
Description The GRIP-GARD PLUS Brushing/Rolling Additive is designed to convert GRIP-GARD PLUS spray paint into a coating that can be used for brush & roll application. 100 Grip Gard Plus (High Gloss)
More informationBEP Blue Barrier Installation and Application Guide
BEP Blue Barrier Installation and Application Guide BEP Blue Barrier is a system of seamless fluid applied products designed to protect the building envelope. Approved assemblies and applications listed
More information1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2.
DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer. PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat
More informationCorlar 2.8 HG High Solids Epoxy
Corlar 2.8 HG High Solids Epoxy GENERAL DESCRIPTION A high build, high solids, two-component, VOC conforming (2.8 lbs./gal.), high gloss epoxy based on Axalta modified polyamide epoxy technology. The resulting
More information3MTM FireDamTM Intumescent Coating WB Installation Manual. Thinner is. Better
0808-3086E 3M FD Intumescent Coating WB 1000 - INSTALLATION MANUAL:Layout 1 9/30/08 2:32 PM Page 1 3MTM FireDamTM Intumescent Coating WB 1000 Installation Manual Thinner is Better 3 1 Index 1. Product
More informationSECTION 1045 PAINT FOR STRUCTURAL STEEL
SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Paint and Paint Material. 1045.1.1 General. All single component paints shall be ready-mixed at the factory to comply with the specification formula for the
More informationSUPERIOR PRODUCTS INTERNATIONAL LEAD-BASED PAINT ABATEMENT ENCAPSULATION METHOD THAT ELIMINATES SANDBLASTING FOR STEEL STRUCTURES
SUPERIOR PRODUCTS INTERNATIONAL INTRODUCES A LEAD-BASED PAINT ABATEMENT ENCAPSULATION METHOD THAT ELIMINATES SANDBLASTING FOR STEEL STRUCTURES Superior Products RUST GRIP and ENAMO GRIP Before 1 LEAD-BASED
More informationBlue Barrier Liquid Wrap 2300
Tools/Materials Needed 5 gal pail of PolyWall Blue Barrier Liquid Wrap 2300 10.1 oz Caulking Tube of Poly Wall Blue Barrier 2200 Joint Filler Caulking gun 9 to 11-inch Hot Dog Style Roller handle and Mini
More informationTOPCOAT System Specifications Corrugated Transite Panels
TOPCOAT System Specifications Corrugated Transite Panels Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT System Specifications Corrugated Transite
More informationIndustry. General Guidelines Bonding and Sealing with Sikaflex. August 2006 / Version 3
Industry General Guidelines Bonding and Sealing with Sikaflex August 2006 / Version 3 Table of Content 1. Introduction 3 2. Selecting Adhesives and Sealants 3 3. Design and Dimensions of Adhesive Joints
More informationPRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
More information1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.
PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials
More information64C1-2-A High Temperature Resistant Insulative Coating
Product Group Characteristics Product Information High temperature coating is formulated for use as a high temperature insulation coating for environments with continuous exposure to temperatures up to
More informationAdhesion Promoter/Primer 3M Adhesion Promoter AP596
Adhesion Promoter/ 3M Adhesion Promoter AP596 3M All Purpose P591 3M Metal P592 Technical Data October 2017 Product Description 3M Adhesion Promoter AP596 and 3M s P591, P592, and are low viscosity adhesion
More informationNAVSEA REVIEWED ASTM F-718. If this product is to be applied as part of a coating system, all components of the system must be as listed on the QPL.
ASTM F-718 COTE-L Industries, Inc. DURABAK-M26 MIL-PRF-32171 If this product is to be applied as part of a coating system, all components of the system must be as listed on the QPL. This NAVSEA-REVIEWED
More informationBallast Water Tanks Repair Guide for Crew
January 2011 Ballast Water Tanks Repair Guide for Crew This brief introduction is only intended as a guide for crew repairs with CHEMCO products Epo-chem RS 500P and RA 500M. This is a guideline for how
More informationTechnical Data Sheet
MATTE CONTRACTOR CHOICE PAINT The Matte Contractor Choice C paint is designed for the contractor; it has good performance and opacity. No odor. Has very good brushability, leveling, durability, adhesion
More informationSection COATING RESTORATION
Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com 80658R StoColor Texture - Coarse Textured Acrylic-Based,
More informationTEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING
SECTION 09960 - TEXTURED COATINGS Coating System Submittals Guide Specification TEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING (SPLIT FACE OR SAND FINISH BLOCK) 1. TEX COTE 600, Textured Coating
More informationB. Paints, Sealants, Adhesives
VERSATEX Paint Specification The Sherwin-Williams Company has completed adhesion testing and accelerated weather testing on VERSATEX Trimboard and makes the following coating recommendations; Surface Preparation
More informationTOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets
TOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss >4% <70% 83mg IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor P is a suitable screed that can be applied on cement-based floors which need high mechanical
More information10P20-14 High Solids Low IR Primer
Technical Data Sheet Product Group Epoxy Primer Characteristics Product Information - A high solids primer for aircraft exteriors meeting the low infrared reflectance requirements of the referenced specification.
More informationSignature Seal 100 Medium-to-High Sheen Sealer VOC Characteristics and Applications
Signature Seal 100 Medium-to-High Sheen Sealer - 100 VOC DESCRIPTION Legacy Signature Seal is a high-gloss, UV-resistant, lacquer-based, crystal-clear sealer. A light coating of Legacy Signature Seal will
More informationImron 1.8 FT-C Flat Waterborne Polyurethane Clearcoat
Imron 1.8 FT-C Flat Waterborne Polyurethane Clearcoat GENERAL DESCRIPTION A flat gloss, isocyanate-free, single component, 1.8 lbs/gal VOC conforming, zero HAPs coating based on unique Axalta waterborne
More informationProtective Coatings for Underground Utility Concrete Structures. By: John E. Davis Inside Sales & Marketing Specialist: Sauereisen, Inc.
Protective Coatings for Underground Utility Concrete Structures By: John E. Davis Inside Sales & Marketing Specialist: Sauereisen, Inc. As our cities and municipalities grow older, the utility and wastewater
More informationHYDROJETTING INFORMATION. a six page issue October 1999
a six page issue Hydrojetting is the surface preparation of steel using high-energy water to remove coatings, corrosion products and other surface contamination such as oil/grease etc. It relies totally
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing
More informationTOPCOAT Restoration Specifications Structural Concrete
TOPCOAT Restoration Specifications Structural Concrete Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications Structural Concrete
More informationCROMAX PRO WB9908 SUPER JET BLACK BASECOAT
CROMAX PRO WB9908 SUPER JET BLACK BASECOAT GENERAL DESCRIPTION A super jet black factory package color that delivers the deepest black to meet the most critical color standards. It features high hiding,
More informationSECTION CONCRETE AND MASONRY COATINGS
80658 StoColor Texture - Coarse Textured Acrylic-Based, Vertical Above-Grade Exterior Wall Coating for New Concrete, Stucco, and Masonry Construction SECTION 099723 CONCRETE AND MASONRY COATINGS Sto Corp.
More informationHVAC Antimicrobial Protected Coatings
HVAC Antimicrobial Protected Coatings Introduction to Shop Applied Coating Technology HVAC Heating, Ventilation, and Air Conditioning Then & Now Although HVAC technology is one of the most practical advantages
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: APPLIED FIREPROOFING REPORT HOLDER: CARBOLINE COMPANY
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 973 Reissued /207 This report is subject to renewal /208. DIVISION: 07 00 00 THERMAL
More informationElastomeric Protected Membrane Roofing Fluid-Applied Protected Membrane Roofing. Restoration Coating System (RCS) over Cap Sheet
07 55 53 Elastomeric Protected Membrane Roofing 07 55 56 Fluid-Applied Protected Membrane Roofing Restoration Coating System (RCS) over Cap Sheet PART 1 - GENERAL 1.1 SUMMARY A. This specification covers
More information3 Scotch-Weld TM. Structural Adhesive Primer EC Technical Data August, 2002
3 Scotch-Weld TM Technical Data August, 2002 Introduction 3M Scotch-Weld is a sprayable corrosion inhibiting adhesive primer. It provides a high degree of protection against corrosive environments both
More informationSP-100 Equipment Wash SP-110 Tool Cleaner SP-120 Internal Storage Lubricant
DESCRIPTION: SP-9888 Pipe Lining is based on the latest Zero VOC Novolac Technology. The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance.
More informationMAKE ROOFS LAST LONGER
MAKE ROOFS LAST LONGER Roof Coatings & Roof Repair Single-Ply Metal Asphalt HIGHEST PERFORMING SYSTEMS. LOWEST APPLIED COST. METAL ROOF RESTORATION Metal Restoration Quick Guide Acrylic Polyurethane High
More informationPRODUCT DATA SHEETS CUSTOM COATINGS FORMULATED TO MATCH YOUR NEEDS USCOATINGS.COM // St. Louis, Missouri
PRODUCT DATA SHEETS CUSTOM COATINGS FORMULATED TO MATCH YOUR NEEDS USCOATINGS.COM 314.205.1500 // St. Louis, Missouri 2 ABOUT U.S. COATINGS We offer a range of solutions designed to fit the needs of our
More informationtwo component high build amine adduct cured phenolic epoxy primer
5 pages Revision of January 2003 DESCRIPTION two component high build amine adduct cured phenolic epoxy primer PRINCIPAL CHARACTERISTICS primer coat in the Sigma Phenguard tank coating system excellent
More informationDPHS521 FL301. Low VOC Primer
Product Information Bulletin Effective 1/99 Low VOC Primer DPHS52 DPHS52 is a 3.5 VOC epoxy primer or primer surfacer designed specifically for use in fleet refinishing operations. The product is lead
More informationELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION
ELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions,
More informationAPPLICATION GUIDELINES EXTERIOR DECK SYSTEM
APPLICATION GUIDELINES EXTERIOR DECK SYSTEM Revision 6 Issue Date: 15 th September 2015 Registered Office The AkzoNobel Building, Wexham Road, Slough, SL2 5DS Page 1 CONTENTS Page 1. SCOPE AND PURPOSE
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong
Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.
More informationGEOGARD LO Base Coat / GEOGARD Finish Coat
GENERAL GUIDELINE SPECIFICATION LO Base Coat / Finish Coat WATERPROOFING SYSTEM FOR MODIFIED BITUMEN ROOFS PART 1 General 1.01 General A. This document is intended to provide only general guidelines regarding
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant
More informationCorrosion Protection for Fisher Valves
Corrosion Protection Product Bulletin Corrosion Protection for Fisher Valves Control valves operate in some of the most severely corrosive conditions imaginable. Valves used near or on the sea are constantly
More informationPaint to Protect TM International Fireproof Technology, Inc Von Karman Ave. Irvine, CA 92614
Paint to Protect TM International Fireproof Technology, Inc. 17528 Von Karman Ave. Irvine, CA 92614 Product Name: DC 315 Fireproof Paint for Foam Name of Company: International Fireproof Technology, Inc.
More informationVELCRO brand Adhesives. p re s s u re sensitive, fire re t a rd a n t, solve n t and heat ac t i v a t e d
VELCRO brand Adhesives p re s s u re sensitive, fire re t a rd a n t, solve n t and heat ac t i v a t e d VELCRO brand Adhesives VELCRO brand products are available with a variety of adhesives to best
More informationMix ratio (by volume): (base component) (activator component) (thinner component)
TECHNICAL DATA SHEET Product Description DeSoto High Temperature urethane primer is a heat resistant coating that can withstand an operating temperature of 232 C (450 F). is used over aluminum and composite
More informationTECH MANUAL TABLE OF CONTENTS
PRO-SPRAY TECH MANUAL TECH MANUAL TABLE OF CONTENTS SURFACE CLEANERS 1-1 ICR-0014, ICR-0015, ICR-1402 1-1 SELF-ETCHING & EPOXY PRIMERS 2-1 A-514 CHROMATE FREE ETCH PRIMER 2-1 A-518 EPOXY PRIMER 2-3 PLASTIC
More informationValspar InspireME Coil and Extrusion Product Guide Specification Section Shop-Applied Coatings for Metal
When you re looking for inspiration you have a new source. valsparinspireme.com is an online experience brimming with ideas and possibilities to fuel your creativity. Valspar InspireME Coil and Extrusion
More informationSteel Rehabilitation Resins MIR-940 & MIR-950
Steel Rehabilitation Resins MIR-940 & MIR-950 Introduction Mirteq s steel primer and vinyl ester based, micro-fiber reinforced resins have been custom formulated for sealing and refurbishing steel structures,
More informationThe Best of Both Worlds!
The Best of Both Worlds! The Best of Both Worlds! A benchmark high-performance polyurethane paint that limits VOC to less than 50g/L or.4172 lbs/gal while delivering superior color and durability. High
More informationEnvironmentally responsible
Product range guide Intergrain Enviropro uses advanced water based polyurethane technology to bring you a high performance range of interior timber floor coatings. Being low VOC and low odour makes Enviropro
More informationFORREST POWDER COATINGS Product Guide
FORREST POWDER COATINGS Product Guide CONTENTS HIGH PERFORMANCE FINISHES Custom Formulations Color matching and specialty formulations Special Special effects including Bonded Metallic and Transparent
More informationm2 Anti-Slip Tape Daylight Fluorescent R13
Product Description: Daylight Fluorescent and glow in Dark Premium Long Life Durable Self Adhesive Anti-Slip Tape which incorporates a bonded and sealed 60-grit Aluminium Oxide, on an EN71 Low Temperature
More informationADVANCED PROTECTIVE COATING SYSTEM Breakthrough Protective Top Coat and High Performance Epoxy Primer
ADVANCED PROTECTIVE COATING SYSTEM Breakthrough Protective Top Coat and High Performance Epoxy Primer VSC 12 TOPCOAT VSC 11 PRIMER Traditional heavy-duty protective coating systems typically utilize a
More informationGently shake the Autowave can prior to use. Prior to clearcoat application: Until completely matt at 25 C 15 minutes at 25 C
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl effect colors. Autowave must be used in conjunction
More informationCoating Types. Coating Systems. Coating Basics. Why coatings are used Component of coatings Methods of protection Service environment
Coating Basics Why coatings are used Component of coatings Methods of protection Service environment Coating types Curing mechanism Design characteristics Limitations Suitable Use Coating Systems Coating
More informationSpecification and Installation
SHAW 5800 SPECIFICATION ADHESIVE FOR SHAW CARPET TILE Any variance from these procedures will become the responsibility of the installer and not the manufacturer. See Shaw s Modular Installation Guidelines
More informationScotch-Weld TM. Epoxy Adhesive/Coating Technical Data July, 2011
Scotch-Weld TM Technical Data July, 2011 Product Description 3M Scotch-Weld is an amber tinted thermosetting adhesive/coating for metal to metal bonding and coating. It can be used to assemble laminated
More information3 Scotch-Weld TM. Epoxy Adhesive 2158 B/A. Technical Data December, 2009
3 Scotch-Weld TM Technical Data December, 2009 Product Description 3M Scotch-Weld is a gray, two-part, high strength adhesive that chemically cures at room temperature. It has good adhesion to a variety
More informationNormadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA
Technical Data Normadur 65 HS PROPERTIES AND RECOMMENDED USAGE Paint type: NORMADUR 65 HS is a fast drying, flexible polyurethane coating with an aliphatic isocyanate curing agent. NORMADUR 65 HS is high-solid
More informationA. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.
SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES
More informationAVM System 500. Aussie Membrane 500
Generic Spec TECH DATA SHEET Sections - 071000 / 071400 / 071416 ICC ESR-2503 L.A. RR#: 25550 Heavy Duty Below Grade Bituminous Waterproofing Membrane Sections 071000 / 071400 / 071416 Fluid Applied Waterproofing
More informationDESIGN GUIDELINE FLUID-APPLIED WATERPROOFING
DESIGN GUIDELINE FLUID-APPLIED WATERPROOFING (TO RESTORE EPDM MEMBRANES) PART 1 GENERAL 1.01 DESCRIPTION A. The scope of this design guideline is to describe the installation of the ALDOCOAT Silicone reflective
More informationHeresite VR-514 TECHNICAL DATA SHEET. VR-514 Typical Properties. Our 50 years of coating history speaks for itself.
Heresite VR-514 Our 50 years of coating history speaks for itself. In 1964, Heresite was the first company to apply coatings to aluminum-finned, copper-tubed heat exchangers. The Heresite coating became
More informationCHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER
CHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER GENERAL DESCRIPTION A three-component, high-performance sealer for premium-quality spot, panel and overall repairs. It provides excellent
More informationDuPont ChromaClear G2-4700S (Hyper Cure - Air Dry and Express Bake)
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaClear G2-4700S is a second generation version of ChromaClear 4700S. ChromaClear G2-4700S is not only the world s fastest air
More informationVAPROLIQUI-FLASH. Liquid Applied Waterproof Flashing Material INSTALLATION INSTRUCTIONS
VAPROLIQUI-FLASH Liquid Applied Waterproof Flashing Material OVERVIEW VaproLiqui-Flash is a liquid applied Waterproof Flashing material for window and door rough opening interfaces. It is designed for
More informationNathan Kofira Technical Development Manager
Nathan Kofira Technical Development Manager Overview 1 2 3 Types of Corrosion in Coatings Mechanisms of Corrosion Corrosion Inhibitor Selection 4 Formulating with Anti-Corrosives 5 Temporary Rust Prevention
More informationDP4101 / DP4104 / DP4107 HS PRIMER
Description 2-component High Solids primer with 2 methods of application: a. primer surfacer; b. non-sanding primer. Colour: white, medium grey and black. Composition based on a special hydroxy functional
More informationDULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS
TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT
More informationEclipse ECL-G-2 Clear High Solids Polyurethane Topcoat
Technical Data Sheet Product Group Polyurethane topcoat Characteristics Product Information ECL-G-2 is a high solids, long life clear coat formulated for use with Eclipse base coat and special effect colors
More informationBharat Heavy Electricals Limited Piping Centre Chennai-17. Specification Number Revision Number Sheet Number PC:E:GF: of 7 CONTENTS
PC:E:GF:001 00 2 of 7 CONTENTS 1 SCOPE 2 PRODUCT SPECIFICATION 3 SURFACE PREPARATION 4 PRIMING 5 COATING 6 FIELD JOINTING 7 INSPECTION AND TESTING PC:E:GF:001 00 3 of 7 Technical Specification for Glass
More informationCC-1004 Ultra High Temperature Epoxy Adhesive
CC-1004 Ultra High Temperature Epoxy Adhesive PRODUCT DESCRIPTION TYPICAL USES Blome CC-1004 is a two part, high temperature, epoxy adhesive used for the installation of abrasion resistant brick and tile
More informationSTANDARD NO.: Z0254. ECO 13848: Added revision table and standard format. Minor corrections made through out the document.
PAGE 1 OF 7 APPROVAL FOR RELEASE FOR USE: POSITION: NAME: DATE: POSITION: NAME: Paint Line Mfg Eng J. Pidima 4/9/2012 Mfg Eng Mgr R.Luety 4/9/2012 Quality Mgr J Meyers 4/9/2012 CHANGE CONTROL: REV: DATE:
More information1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.
1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate
More informationFireShield System Specifications Mineral Surface Cap, Mop Granule and Torch Granule APP Cap Sheets
FireShield System Specifications Mineral Surface Cap, Mop Granule and Torch Granule APP Cap Sheets Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com FireShield
More informationAssociated Spec Consultants, Inc. February 27, 2014 SECTION ARCHITECTURAL COATINGS
SECTION 099650 ARCHITECTURAL COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More information