Portable combustion and emissions analysers

Transcription

1 Emissions & calibration instruments Portable combustion and emissions analysers A full range of accurate, robust and versatile portable analysers for industrial measurements RASI 800 MCERTS certified, suitable for EA compliance emissions reporting RASI 900 semi-continuous monitoring meets EPA protocol for emissions reporting RASI 700 combined emissions combustion and BIOGAS analyser

2 Emissions Analyser Selection Guide Maximum Gas Sensors at the same time Gas measurements O2 sensor ( 0-25 % ) standard standard standard CO H2 compensated sensor ( ppm) optional optional standard Low CO H2 compensated sensor (0-500 ppm, 0.1 ppm resolution) optional optional optional High CO sensor ( ppm) optional optional optional CO% sensor (0-10 %) optional optional optional NO sensor ( ppm) optional optional optional LOw NO sensor (0-500 ppm, 0.1 ppm resolution) optional optional optional NO2 sensor ( ppm) optional optional optional Low NO2 sensor (0-500 ppm, 0.1 ppm resolution) n/a n/a optional SO2 sensor ( ppm) optional optional optional H2S sensor ( ppm) optional optional optional H2 sensor (0-1 %) n/a n/a optional CO % (0-10 %NDIR) n/a optional optional CO2% NDIR optional optional optional HC(CH4) % (0 to 5 % NDIR) n/a optional optional HC (40000 ppm NDIR) optional optional n/a HC ppm Low range ( ppm NDIR) n/a n/a optional HC ppm C3H8 (0 to 5000 ppm NDIR) n/a optional optional CH4 % (0-100 % Biogas NDIR) optional n/a optional CO2% (0-100 % Biogas NDIR) optional n/a optional H2% ( % TDC) n/a n/a optional Other measurements Velocity optional optional optional Flow/Flow Mass optional optional optional Temperature standard standard standard Draught, Pressure and differential standard standard standard Gas Sample Conditioning Manual Water trap standard n/a n/a Gas Cooler and condensate pump n/a standard standard Line Filter standard standard standard NOx filter for CO standard standard standard Fresh-air in valve for auto set to zero and long term measurement n/a standard standard CO sensor protection protection Optional standard standard Communications/storage Bluetooth standard standard optional SD card standard standard optional USB standard standard n/a RS232 n/a n/a standard Internal Memory standard standard standard Data logging ( auto) optional standard standard Emissions Calculations standard standard standard Combustion Calculation standard standard standard Fuel list standard standard standard Printer optional standard standard Sampling probes Standard modular sampling probe with Viton Line optional optional optional Industrial Probe with heated head and glass wool filter with Viton Line n/a optional optional Heated Line n/a n/a optional Probe Max temperature 1200 C 1200 C 1700 C

3 RASI 800 Portable Emissions & Combustion Analyser The RASI 800 MCERTS certified emissions analyser is suitable for compliance emissions reporting Key Features RASI 800 Base Unit The hart of the analyser, built in a robust protective transport case Contains up to 8 measurement cells Gas sampling pump, Peltier gas cooler, condensate pump and filters Set to zero valve CO sensor protection Gas Sampling Probe connection Integrated fast printer RCU Wireless remote control unit Use the wireless RCU to remotely control all the functions of the analyser and display the measurement value from a comfortable location. Remotely control all the functions of the analyser including launching an auto-zero Display measurement value on large 3.5 TFT graphic colour display The long range Bluetooth eliminate the needs of long sampling probes Automatic or manual data logging with data export to integrated SD card Intuitive tasks oriented application menu for easy operation Use as separate manometer, flow meter or thermometer with-out carrying the base unit Superior Peltier Gas Sample Conditioning The Peltier gas cooler and the condensate pump automatically removes moisture from the gas stream and provides a dry sample for accurate compliance testing as indicated by the regulatory Agency. It also protects the measurement cells from moisture which is the main cause of sensor failure. CO sensor protection To protect the CO cell from unexpected excessive levels of CO ( threshold user selectable), the analyser automatically switches to the higher range CO sensor ( if a 2nd sensor is installed). The Low CO is automatically purged with a dedicated pump which supplies ambient air to protect the sensor. Sensors conditioning technology deliver best accuracy Both the electrochemical and NDIR are continuously temperature monitored and compensated. A sophisticated software matrix compensate for sensors cross-interference to deliver best accuracy. Simplified operation with the Intuitive Task NDIR sensor for HC and CO2% New developed dual NDIR bench for direct CO2% measurement ( instead of calculated) and HC in ppm value. NDIR technology for HC offers a much wider scope of application compared to the traditional Pellistor type sensor as it does not require minimum O2 level to function. Semi Continuos monitoring The wake and sleep mode takes gas measurements at user defined intervals. During the sleep mode the analyser is purged with ambient air. Measurement data are automatically saved in the internal memory of the RCU and ready to be exported to the SD card in CSV format. Measurements Capabilities O2 LL CO Low CO NO NO2 NOx Low NO CO% SO2 H2S CO2% NDIR HC NDIR Smoke Flow Pressure Temperature Draught Features Max Sensors 8 Standard Option Built-in gas cooler and condensate pump O2 oxygen cell ( all other cells are optional) CO sensor protection Automatic set to zero valve for long term measurement Condensate monitor and alarm Flow measurement RCU remote control unit Sampling probes The dedicated task menu gives direct access to your application. Simply select your Task, i.e flue gas measurement, your measurement programme, for example Engine Emissions and analyser is ready to operate. Up to 4 measurements programme can be configured with the desire settings such as O2% reference, fuel, practical order of the display measurements. Select a Task Select an Application Start Measuring Log your data

4 RASI 800 Portable Emissions & Combustion Analyser Specifications Range Accuracy Resolution Sensor Type % ± 0.2% Vol abs 0.01% Vol EC CO(H2 compensated) ppm ± 10 ppm or ± 5% rdg up to 4,000 ppm ± 10 % rdg from 4,000 to 10,000 ppm CO ppm ± 100 ppm or ± 5% rdg up to 4,000 ppm ± 5 % rdg from 4,000 to 20,000 ppm CO % 0-10% ± 0.02% of rdg up to 4 % ± 10% of rdg up to 4 % to 10 % 0.01% EC Low CO(H2 compensated) ppm ± 2 ppm or ± 5% reading 0. NO ppm ± 5 ppm or ± 5% rdg up to 1,000 ppm ± 10 % rdg from 1,000 to 5,000 ppm Low NO ppm ± 2 ppm or ± 5% reading 0. NO ppm ± 5 ppm or ± 5% rdg up to 200 ppm ± 10 % rdg from 200 to 1,000 ppm SO ppm ± 10 ppm or 5% rdg up to 2,000 ppm ± 10 % rdg from 2,000 to 5,000 ppm H2S ppm ± 5 ppm or ± 5% rdg up to 200 ppm ± 10 % rdg from 200 to 2,000 ppm 1 or 2 gas NDIR Bench CO2 % 0-40 % ± 0.3% vol or ± 5% rdg 0.01% Vol NDIR HC ppm/hc % ppm/0-4% ± 100 ppm./0.01% 100 ppm/0.01% NDIR 3 GAS NDIR Bench CO2% 0-30 % ± 0.5% vol or ± 3% rdg 0.01% Vol NDIR CO% 0-10 % ± 0.03% vol or ± 3% rdg 0.01% Vol NDIR HC (CH4) or 0-3% ± 0.03% vol or ± 3% rdg 0.01% Vol NDIR HC (C3H8) ppm ± 30 ppm or ± 3% rdg 1 ppm NDIR Temperature and Pressure/Smoke Gas Temperature C ± 2 C 0.1 C TC type K Air Temperature -50 C to 100 C ± 1 C 0.1 C TC Type K Draught/Diff Pressure ( Base) -100 to 100 hpa ± 0,02 hpa 0.01 hpa Piezoresistive Draught/Diff Pressure ( RCU) -200 to 200 hpa ± 0,02 hpa 0.01 hpa Piezoresistive Flow Velocity 3 to 100 m/sec ± 1 m/sec or ± 3 % of rdg 0.1 m/sec Pitot Tube Smoke ( soot) manual by smoke pump or automatic using heated probe with filter Calculations Efficiency 0 to 120 % 0.1 % Calculated Air Ratio 1 to Calculated Excess Air 0 to 99,9% 0.1% Calculated Heat losses 0 to 99.9 % 0.1% Calculated CO2% ( when CO2% NDIR not installed 0 to CO2% max ± 0.3% vol 0.1% Flue Gas Dew Point 0 to 99.9 C 0.1 C Calculated Fuel Selection most common fuels plus user definable Emissions Calculations Oxygen normalization, automatic conversion ppm, mg/m3 for all toxic gas Memory, data capture and communication Storage medium logs on internal memory, 2GB on standard SD card, Data export to CSV file, download via SD card included as standard Digital communications mini USB, Bluetooth General Gas Sample Preparation Integral Peltier Cooler with constant 5 C dew Point, perilstatic pump for condensate removal RCU BASE UNIT Display 3.5 TFT colour display, 6 lines, full graphic no display Weight, Dimension ( W x L x H) 6 Kg, 470x314x 235 with case and RCU IP protection IP20 IP 20 AC/DC Power Inductive trough base unit VAC, Hz, 12 VDC Battery, Battery life Li/ION, 30 hours Li/ION 20 hours, 10 hours with cooler on Operating/Storage Temperature 5 to 45 C / -20 to 50 C 5 to 45 C / -20 to 50 C Warranty 2 years instruments 1 year CO, NO,NO2,SO2,H2S cells, 2 years O2 cell, 2 years NDIR

5 RASI 800 Portable Emissions & Combustion Analyser Gas Sampling Probes EiUK offer a large selection of gas sampling probes to match your application. All our probes are supplied with a special Viton line to eliminate sample absorption and to increase the analyser response time. A choice of standard or industrial probes is outlined below. Engine Probe The engine probe is specifically designed for sampling on gas or diesel CHP engines: It features Special Viton hose for maximum NO2 accuracy Temperature measurement Back Pressure measurements Special positioning cone spring loaded Standard Gas Sampling Probe The standard sampling probe is available in different lengths and different materials. It comes complete with integrated thermocouple for temperature reading and positioning cone. More than one probe shaft can be ordered. Industrial Gas Sampling Probe with heated and unheated line The industrial gas sampling probes come with heated glass wool replaceable filter. and choice of heated or unheated line with integrated type K or S thermocouple. Probe Shaft Stainless Steel: Tmax 1200 C lengths: 360, 500, Special Hose for gas sampling and continuos pressure measurement Special Viton line for eliminating sample absorption ( optimal for NO2/SO2) Hose length: 2.7 How to order to make your selection please state the following: Gas to be measured ( the analyser comes standard with O2 cell only) Maximum 6 electrochemical cells and one NDIR bench can be installed at the same time Probe length Temperature of the stack When selecting your analyser, please consider a few important factors: True NOx require both NO and NO2 measurement cells installed. Most industrial applications will require NO2 cell installed to provide correct NOx reading. CO2 % calculated values which are fuel dependant can be very erratic. Your application might require an NDIR infrared sensor ( ie stack emissions, CHP engines, Cement plants). Probe Shaft Stainless Steel: Tmax 850 C lengths: 360, 500, 750 mm, 1m,1.5m, 2 m Probe Shaft Inconel 600: Tmax 1200 C lengths: 500, 750mm, 1m, 1.5 and 2m Special Hose for gas sampling and continuos pressure measurement Special Viton line for eliminating sample absorption ( optimal for NO2/SO2) Hose length: 2.7 or 5 m Probe Shaft Stainless Steel: Tmax 850 C lengths: 380, 500, 750 mm, 1m, 1.5m, 2m Probe Shaft Inconel 600: Tmax 1200 C lengths: 500, 750mm, 1m, 1.5m and 2m Probe Shaft Ceramic: T Max 1700 C Available Length: 1m. Heated line Self regulated heated line (Tmax 160C) Length available 3 or 5 m Internal material: Special Viton Unheated line Length available 3 or 5 m. Internal material: Special Viton Online View Software Supplied as standard with the analyser, this powerful software allows you to view data in real time on a laptop or PC. Data are displayed in TEXT, GRAPHICAL or BAR format. The software automatically saves and creates an excel file of the measurements taken. Communication is established via bluetooth or USB port. Data Management Save time and ensure traceability. Simply upload your sites and log measurement values under each site: Our new concept include: Site Administration Data administration Data Export on SD card Automatic data logging

6 RASI 901 Portable Emissions Analyser The toughest and rugged Portable Emissions Analyser ever built, suitable for long term measurements. The RASI 901 it is with-out doubt the most complete Portable Emissions Analyser available on the market today. The rugged construction, the easy to use task menu and the and superior sensors technology, delivers high accurate and repeatable readings overtime. The advanced sample conditioner which includes an active Peltier cooler, moisture removal pump and self-regulated heated line, sets new standards in portable emissions monitoring. Key Features Large 10 lines back light display icon based displays all the parameters that you need for your application Automatic data logging function Bluetooth connectivity and new mobile app. The standard bluetooth allows for real time data transfer to a PC or to an android base smart mobile device. The new free application speeds up your testing, keeps you away from dirty and noisy rooms and ensure data collection. There is no need anymore for long sampling lines or to stay close to the sampling points. Just enjoy the analyser reading from a more convenient location Connect Start measuring Stop pump Save data data Superior Peltier Gas Sample Conditioning The Peltier gas cooler and the condensate pump automatically removes moisture from the gas stream and provides a dry sample for accurate compliance testing as indicated by the regulatory Agency. It also protects the measurement cells from moisture which is the main cause of sensor failure. Heated Line A heated sample line is used to keep the gas sample above the dew point to prevent the absorption of gases into the water phase. This provides conditions for more accurate measurements as gases are not lost into the condensate. Given the solubility of NO2, the heated line is recommended for maximising NOx accuracy readings. Ideal for long term measurement cycles If your application requires long term measurements, then don t look any further. The RASI 901 features the necessary hardware to be left in the stack for days, weeks or even months with-out compromising in accuracy or damaging the measurement cells. Heated line Peltier Cooler Condensate pump for water removal Automatic set to zero function The wake and sleep automatic programme allows you to measure and log data at defined intervals. Maximum 9 gases Built-in gas cooler and condensate pump O2 long life, CO (H2 compensated) Other measurements cells CO sensor protection Automatic set to zero valve for long term measurement Pressure, draught, temperature Flow, and mass flow measurement Bluetooth, SD card Sampling probes Integrated fast printer A TRUE 9 gases analyser designed to cover all your applications Up to 6 electrochemical cells and one NDIR infrared bench can be installed at the same time to deliver the most comprehensive emissions analyser in the market NDIR technology to detect HC ppm values A new developed infrared bench delivers extremely accurate readings down to ppm values for detecting low level of hydrocarbons in term on CH4 of C3H8. Measurements Capabilities O2 LL CO Low CO NO NO2 NOx Low NO/NO2 CO% SO2 H2S CO2% NDIR HC NDIR H2 Flow Pressure Temperature Draught Smoke Standard Features Option

7 RASI 901 Portable Emissions Analyser Specifications Range Accuracy Resolution Sensor Type % ± 0.2% Vol abs 0.01% Vol EC CO(H2 compensated) CO CO % 0-10% ppm ppm ± 10 ppm or ± 5% rdg up to 4,000 ppm ± 10 % rdg from 4,000 to 10,000 ppm ± 100 ppm or ± 5% rdg up to 4,000 ppm ± 5 % rdg from 4,000 to 20,000 ppm ± 0.02% of rdg up to 4 % ± 10% of rdg up to 4 % to 10 % 0.01% EC Low CO(H2 compensated) ppm ± 2 ppm or ± 5% reading 0. NO ppm ± 5 ppm or ± 5% rdg up to 1,000 ppm ± 10 % rdg from 1,000 to 5,000 ppm Low NO ppm ± 2 ppm or ± 5% reading 0. NO ppm ± 5 ppm or ± 5% rdg up to 200 ppm ± 10 % rdg from 200 to 1,000 ppm Low NO ppm ± 3 ppm or ± 5% reading 0. SO2 H2S H2 0-2 % ppm ppm ± 10 ppm or 5% rdg up to 2,000 ppm ± 10 % rdg from 2,000 to 5,000 ppm ± 5 ppm or ± 5% rdg up to 50 ppm ± 10 % rdg above 50 ppm ± 0.02 % rdg or ± 5 % of rdg up 1 % ±10% rdg above 1 % 0.01% EC 1 GAS NDIR Sensor CO2 % 0-40 % ± 0.3% vol or ± 5% rdg 0.01% Vol NDIR 3 GAS NDIR Bench CO2% 0-50 % ± 0.5% vol or ± 3% rdg 0.01% Vol NDIR CO% 0-10 % ± 0.03% vol or ± 3% rdg 0.01% Vol NDIR HC (CH4) or 0-5% ± 0.03% vol or ± 3% rdg 0.01% Vol NDIR HC (C3H8) or ppm ± 30 ppm or ± 3% rdg 1 ppm NDIR HC (CH4) ppm ± 30 ppm or ± 3% rdg 1 ppm NDIR Temperature and Pressure Gas Temperature C ± 2 C 0.1 C TC type K/S Air Temperature -50 C to 100 C ± 1 C 0.1 C TC Type K Draught/Diff Pressure -100 to 100 hpa ± 0,02 hpa 0.01 hpa Piezoresistive Flow Velocity/mass 3 to 100 m/sec ± 1 m/sec or ± 3 % of rdg 0.1 m/sec Pitot Tube Calculations Efficiency 0 to 120 % 0.1 % Calculated Air Ratio 1 to Calculated Excess Air 0 to 99,9% 0.1% Calculated Heat losses 0 to 99.9 % 0.1% Calculated CO2% ( when CO2% NDIR not installed 0 to CO2% max ± 0.3% vol 0.1% Calculated Fuel Selection Most common fuels plus user definable Emissions Calculations O2 Corrections, automatic conversion ppm, mg/m3 for all toxic gases, mass measurement for SO2, NOx and CO using an optional pitot tube Memory, data capture and communication Storage medium Digital communications Analogue communications General Gas Sample Preparation Display 8500 logs on internal memory, 2GB on standard SD card, Data export to CSV file, download from Internal memory or via SD card (optional) RS232, Bluetooth Weight, Dimension ( W x L x H) 7 Kg, 530 x 490x 310 IP protection Power/Mains 8 x 4-20 ma output, 4-20 ma or 0-10 V input Integral Peltier Cooler with constant 5 C dew Point, Peristaltic pump for automatic condensate removal Back light Graphic LCD display, 10 lines, full graphic, task oriented menu IP21 Operating/Storage Temperature 5 to 45 C / -20 to 50 C Warranty Ni-Mh Internal rechargeable batteries, AC VAC, Hz 2 years instruments 1 year CO, NO,NO2,SO2,H2S, H2 cells, 2 years O2 cell, 2 years NDIR

8 RASI 901 Portable Emissions Analyser RASI 901-MK Emissions Analyser for marine applications Gas Sampling Probes Eiuk offer a large selection of gas sampling probes to match your application. All our probes are supplied with a special Viton line to eliminate sample absorption and to increase the analyser response time. A choice or standard or industrial probes are outlined below. Standard Gas Sampling Probe The standard sampling probe is available in different lengths and different materials. It comes complete with integrated thermocouple for temperature readings and positioning cone. More that one probe shaft can be ordered. Industrial Gas Sampling Probe with heated and unheated line The industrial gas sampling probes come with heated glass wool replaceable filter. and choice of heated or unheated line with integrated type K or S thermocouple. The RASI901-MK Portable Emissions Analyser Marine Kit provides a reliable and accurate measurements for O2, CO, CO2, True NOx (NO+NO2), Low SO2, and CxHy hydrocarbons to help ships achieve and confirm compliance with MARPOL AnnexVI and the NOx Technical Code. The KIT is equipped with: 02, Low CO, Low NO, Low NO2, SO2 electrochemical sensors Special NDIR bench for CO2 % and CH4 ppm Heated sampling line to provide accurate NO2 and SO2 readings Probe Shaft Stainless Steel: Tmax 850 C lengths: 360, 500, 750 mm, 1m,1.5m, 2 m Probe Shaft Inconel 600: Tmax 1200 C lengths: 500, 750mm, 1m, 1.5 and 2m Special Hose for gas sampling and continuos pressure measurement Special Viton line for eliminating sample absorption ( optimal for NO2/SO2) Hose lenght: 2.7 or 5 mt Probe Shaft Stainless Steel: Tmax 850 C lengths: 380, 500, 750 mm, 1m, 1.5m, 2m Probe Shaft Inconel 600: Tmax 1200 C lengths: 500, 750mm, 1m, 1.5m and 2m Probe Shaft Ceramic: T Max 1700 C Available Length: 1m. Heated line Self regulated heated line (Tmax 160C) Length available 3 or 5 m Internal material: Special Viton Unheated line Length available 3 or 5 m. Internal material: Special Viton Ordering Information to make your selection please state the following: Gas to be measured ( the analyser comes standard with O2 and CO(H2) cell only) Maximum 6 electrochemical cells and one NDIR bench can be installed at the same time Probe type and length Temperature of the stack When selecting your analyser, please consider a few important factors: True NOx require both NO and NO2 measurement cells installed. Most of industrial application will require NO2 cell installed to provide correct NOx reading CO2 % calculated values which are fuel dependant can be very erratic. If Your application might require an NDIR infrared sensor ( ie stack emissions, CHP engines, Cement plants) HC in diesel engines are normally at ppm level in term of CH4 Online View Software Supplied as standard with the analyser, this powerful software allows you to view data in real time on a laptop or PC. Data are displayed in TEXT, GRAPHIC or BAR format. The software automatically save and create an excel file of the measurements taken. Communication is established via bluetooth or RS233 port Data Management Save time and ensure traceability. Simply upload your sites and log measurement values under each site: Our new concept include: Site Administration Data administration Data Export on SD card Automatic data logging

9 RASI 700 Industrial Flue Gas and Emissions Analyser The smallest hand held industrial flue gas emissions and gas analyser available today Key Features 8 Gas Hand Held Analyser This powerful industrial hand held unit can be used as a combustion analyser,emissions analyser or Biogas analyser. Up to 8 measurement sensors can be installed at the same. NDIR sensor for HC and CO2% stack emissions New developed dual NDIR bench for direct CO2% measurement ( instead of calculated) and HC in ppm value. NDIR technology for HC offer a much wider scope of applications compared to the traditional Pellistor type sensor as it does not require a minimum O2 level to function. Bluetooth connectivity and new mobile app. The standard bluetooth allows for real time data transfer to a PC or to an android base smart mobile device. The new free application speeds up your testing, keeps you away from dirty and noisy rooms and ensures data collection. There is no need anymore for long sampling lines or to stay close to the sampling points. Just enjoy the analyser readings from a more convenient location. Connect Start measuring Stop pump Save data data Measurements Capabilities O2 LL CO Low CO NO NO2 NOx Low NO CO% SO2 CH4 % CO2% NDIR HC NDIR Smoke Flow Pressure Temperature Draught Smoke Maximum 8 gases ( not all configurations are possible) O2 sensor CO, NO, NO2, SO2, H2S, CO2%. HC, CH4% CO sensor protection( mandatory if high and low CO is installed) Large integrated and removable water trap Pressure, draught, temperature measurement Flow and Gas Velocity Bluetooth, SD card, USB, IRDA and manual logging Auto data logging function Fine draught 0.1 pa resolution for BIOMASS boiler testing Sampling probes Fast IRDA Printer ( external) RASI 700 for BIOGAS and CHP s engines RASI 700 is also available as sa eparate BIOGAS analyser for O2, CH4, CO2 and H2S or as a combined unit for measuring NOx and CO measurements from the exhaust gas engine. Standard Features Option Simplified operation with the Intuitive Task Menu IRDA fast printer Our fast IRDA printer prints data faster than any other model available on the market. No feeding is required and changing paper rolls takes a matter of seconds. The print out header can be customised to reflect customer details, such as company name, contact name and telephone number. The dedicated task menu gives direct access to your application. Simply select your Task, i.e flue gas measurement, your measurement programme, for example Engine Emissions and analyser is ready to operate. Up to 4 measurements programme can be configured with the desire settings such as O2% reference, fuel, practical order of the display measurements. Select a Task Select an Application Start Measuring Save Data

10 RASI 700 Industrial Flue Gas and Emissions Analyser Specifications Range Accuracy Resolution Sensor Type % ± 0.2% Vol abs 0.1% Vol EC CO(H2 compensated) CO CO % 0-10% ppm ppm ± 10 ppm or ± 5% rdg up to 4,000 ppm ± 10 % rdg from 4,000 to 10,000 ppm ± 100 ppm or ± 5% rdg up to 4,000 ppm ± 5 % rdg from 4,000 to 20,000 ppm ± 0.02% of rdg up to 4 % ± 10% of rdg up to 4 % to 10 % 0.01% EC Low CO(H2 compensated) ppm ± 2 ppm or ± 5% reading 0. NO ppm ± 5 ppm or ± 5% rdg up to 1,000 ppm ± 10 % rdg from 1,000 to 5,000 ppm Low NO ppm ± 2 ppm or ± 5% reading 0. NO2 SO2 H2S ppm ppm ppm ± 5 ppm or ± 5% rdg up to 200 ppm ± 10 % rdg from 200 to 1,000 ppm ± 10 ppm or 5% rdg up to 2,000 ppm ± 10 % rdg from 2,000 to 5,000 ppm ± 5 ppm or ± 5% rdg up to 50 ppm ± 10 % rdg above 50 ppm 1 GAS NDIR BENCH for emissions measurement CO2 % 0-40 % ± 0.3% vol or ± 5% rdg 0.01% Vol NDIR 2 GAS NDIR Bench for emissions measurement CO2% 0-40 % ± 0.5% vol or ± 3% rdg 0.01% Vol NDIR HC ppm ± 100 ppm 100 ppm NDIR 2 GAS NDIR Bench for Gas Measurement CH % ± 30 ppm or ± 3% rdg 0.01 % NDIR CO % ± 30 ppm or ± 3% rdg 0.01% NDIR Temperature and Pressure Gas Temperature C ± 2 C 0.1 C TC type K/S Air Temperature -50 C to 100 C ± 1 C 0.1 C TC Type K Draught/Diff Pressure -100 to 100 hpa ± 0,02 hpa 0.01 hpa Piezoresistive Flow Velocity 3 to 100 m/sec ± 1 m/sec or ± 3 % of rdg 0.1 m/sec Pitot Tube Calculations Efficiency 0 to 120 % 0.1 % Calculated Air Ratio 1 to Calculated Excess Air 0 to 99,9% 0.1% Calculated Heat losses 0 to 99.9 % 0.1% Calculated CO2% ( when CO2% NDIR not installed 0 to CO2% max ± 0.3% vol 0.1% Calculated Fuel Selection Most common fuels plus user definable Emissions Calculations Oxygen normalization, automatic conversion ppm, mg/m3 for all toxic gas Memory, data capture and communication Storage medium logs on internal memory, 2GB on standard SD card, Data export to CSV file from SD card Digital communications USB, Bluetooth General Gas Sample Preparation Integrated replaceable water trap Display 3.5 TFT colour display, 6 lines, full graphic Weight, Dimension ( W x L x H) 750 g, 110x225x52 mm IP protection IP21 Power/Mains Ni-Mh Internal rechargeable batteries, OPtional LI-ION, AC VAC, Hz Operating/Storage Temperature 5 to 45 C / -20 to 50 C Warranty 2 years instruments 1 year CO, NO,NO2,SO2,H2S, cells, 2 years O2 cell, 2 years NDIR

11 RASI 700 Industrial Flue Gas and Emissions Analyser RASI 700 Engine Exhaust Gas analyser Gas Sampling Probes Eiuk offer a large selection of gas sampling probes to match your application. All our probes are supplied with a special Viton line to eliminate sample absorption and to increase the analyser response time. A choice or standard or industrial probes is outlined below. The RASI700 engine Kit is the ideal tool for service and commissioning engineers working on CHP stationary engines. The Kits comes with all the accessories to operate, and it is installed with: O2, CO, NO and NO2 cells Engine sampling probe Read in ppm and mg/m3 with O2 reference IRDA printer Blue Tooth Carrying Case Adds on: CO2%, CH4% ad H2S measurement for gas sample. Standard Gas Sampling Probe The standard sampling probe is available in different lengths and different materials. It comes complete with integrated thermocouple for temperature readings and positioning cone. More that one probe shaft can be ordered. Probe Shaft Stainless Steel: Tmax 850 C lengths: 360, 500, 750 mm, 1m,1.5m, 2 m Probe Shaft Inconel 600: Tmax 1200 C lengths: 500, 750mm, 1m, 1.5 and 2m Special Hose for gas sampling and continuos pressure measurement Special Viton line for eliminating sample absorption ( optimal for NO2/SO2) Hose length: 2.7 or 5 mt Engine Probe The engine probe is specifically designed for sampling on gas or diesel CHP engines: It features Special Viton hose for maximum NO2 accuracy Temperature measurement Back Pressure measurements Special positioning cone spring loaded Probe Shaft Stainless Steel: Tmax 1200 C lengths: 360, 500, Special Hose for gas sampling and continuos pressure measurement Special Viton line for eliminating sample absorption ( optimal for NO2/SO2) Hose length: 2.7 How to order to make your selection please state the following: Gas to be measured ( the analyser comes standard with O2 cell only) Maximum 6 electrochemical cells and one NDIR bench can be installed at the same time Probe length Temperature of the stack When selecting your analyser, please consider a few important factors: True NOx require both NO and NO2 measurement cells installed. Most of industrial application will require NO2 cell installed to provide correct NOx reading CO2 % calculated values which are fuel dependant can be very erratic. Your application might require an NDIR infrared sensor ( ie stack emissions, CHP engines, Cement plants) Online View Software Supplied as standard with the analyser, this power full software allow you to view data in real time on a laptop or PC. Data are displayed in TEXT, GRAPHICAL or BAR format. The software automatically saves and creates an excel file of the measurement taken. Communication is established via blue tooth or USB port. Data Management Save time and ensure traceability. Simply upload your sites and log measurement values under each site: Our new concept include: Site Administration Data administration Data Export on SD card Automatic data logging

12 Emissions & calibration instruments Service and Support Related Products We are proud of our level of service that we provide to our customers. We can state with confidence that our service turnaround for portable emission testers is no longer than 2 days. Service & Repair are 100% handled in our ISO 9001:2008 accredited lab in Daventry. For fixed installation we offer various level of service contracts which are discussed on a case-by-case basis to match our customers expectations. Test Equipment EiUK is also a market leader manufacturer for: Temperature and Pressure Calibrators for engine maintenance Pressure sensors Hand held Pressure Indicator for gas measurements Eurotron instruments (UK) ltd. Unit 18 Austin Way Royal Oak Industrial Estate Daventry Northants NN11 8QT England T: +44 (0) F: +44 (0) sales@eurotron-uk.com Data subjected to alteration without notice. Pub ID AQE2015.V02 Printed in the U.K, 04/15