new Saturno LED - suspension

Transcription

1 352 Saturno LED - suspension new Accessories On request: fi xture with bracket. 145 Ø490 acc. 540 Skirt opal transp In polycarbonate, internally grooved and anti-uv. To be used as an aesthetic finish and to reduce direct glare / acc. 538 suspension for ceiling fitting In stainless steel. Adjustable suspension (0/180 ) to allow proper mounting of the Saturno. Purchase separately chain/tiges acc Box To be used when purchasing Saturno EM version, with sub-code 07. Ø512

2 Saturno LED - suspension 353 Housing: in die-cast aluminium with cooling fi ns. Optics: made of PMMA with high temperature resistance and UV rays. Diffuser: 4mm thick tempered glass, resistant to thermal shocks and impacts (art. 2882/83/84). Coating: powder-coated with graphite grey polyester resin, resistant to corrosion and saline environments. Equipment: silicone rubber gasket; external screws and bolts in stainless steel. Insulation connector for quick installation with no need to open the fi xture. LED: Power factor Luminous flux maintenance 80% (L80B10) Ta = C +35 C 80% (L80B10) Ta = C +40 C 80% Ta = -40 C +45 C (L80B20) (art HP) 90% h (L90B10) Ta = C +35 C electronic safety device to protect the LED module and SURGE the related ballast compliant with EN It works in two modes: - differential mode: surge between power cables and between the phase and neutral. - common mode: surge between power, L/N and ground cables or between the fixture s body if it is of class II and installed on a metal pole. On request: for Class II fixtures, protection up to 10KV. Low Flicker: product with a very low flicker; uniform light for greater eye protection. The heat dissipation system was designed to allow LED operation at adequate temperatures and guarantee excellent performance/effi ciency and long life. The fixture is equipped with air recirculation valve and insulation connector for quick installation with no need to open the fixture. Designed with an optical system capable of controlling the potential glare created by the growing light intensity of LEDs while achieving high photometric performance. Energy saving: the comparison shows how Saturno can save more energy compared to energy saving!!! conventional discharge lamps and meet applicable standards. We recommend using LED technology to save energy in environments where lights stay on for a long time. Fixture room (m) LUX Qtx P tot W Energy saving Saturno (120 LED) 40x20x % Reflecteur JM-E 250W 40x20x SUSPENSION Saturno (204 LED) 60x40x % Reflecteur JM-E 400W 60x40x On request: possibility for the various options for managing the supply point (see table on p. XVII). Presence sensor or light sensor to wall or ceiling (see chapter dimmable fixture control kit).

3 354 Saturno LED - with sensor SENSOR STAND-ALONE Presence sensors - ON/OFF On request with sub-code -19: Saturno with easy-to-use, safe and convenient standalone presence sensor; available in the 1/10V version (with sub-code -1219). TECHNICAL SPECIFICATIONS Power source Vac - 50/60Hz High frequency 5.8GHz±75MHz, ISM wave band, <0.5mW Detection angle ceiling: wall: 150 Detection area 8 max (choice) Detection motion speed 0.5~3m/s Installing height ceiling: 3-15 m max. Power consumption 0.5W (standby), <1W (operation) IP degree IP65 Technology Microwave Operating temperature (sensor) C Hold time (choice) 5s / 30s / 90s / 3min / 20min / 30min Ambient light (choice) 5lux / 15lux / 30lux / 50lux /100lux / 150lux / Disable (Optional) remote control to change parameters after installation, without opening the fi xture SCAN AREA: can be reduced by selecting the relevant combination on the DIP switches to set sensor data for each application. max. 15 m 150 HOLD TIME: refers to the amount of time the lamp stays on at 100% of the light level after no motion is detected. max. 8 m SENSOR DIMM DALI Presence and light sensors - DIMM DALI On request with sub-code -0061: Saturno DALI version with easy-to-use, safe and convenient automatic presence and light sensor. TECHNICAL SPECIFICATIONS Rated supply voltage Vac - 50/60Hz Power consumption 2 W Output, stand-by 0,5 W Operating temperature (sensor) C IP degree IP65 Time delay (regolabile) min: 30sec - max: 60min Technology PIR Max. installation height 16m Light detection angle 13 Motion detection angle high low Momentary-action switch input for on/off switching and dimming All functions can be set by request or with the (optional) remote control Lights can be dimmed from 100% to 1% (with the option to go completely OFF) Default Parameter Motion Detector A light-level 1 time delay B sec. level 2 if vacant Light level recognition area h * d 8 m 1.8 m 10 m 2.3 m Presence / motion detection h * Zoom d 8 m low 12.0 m 9 m low 13.5m 12 m 2.7 m 10 m low 15.0 m Light B A α = 13 h 14 m 3.2 m 16 m 3.7 m α high = 60 α low = 72 h 11m low 16.5 m 12 m low 18.0 m 12 m high 14.0 m 13 m high 15.2m 14 m high 16.4 m 1 2 Time Time can be set from 30 sec. to 60 min. d d 15 m high 17.6 m 16 m high 18.8 m

4 Saturno LED - suspension LED 62W= 4kV 104W=4kV 145W=4kV SURGE cd/klm 120 LED 168 LED 2882 Saturno - narrow beam wattage colour weight code code W K - ølm - CRI LED graphite K lm - CRI 80 LED graphite K lm - CRI 80 LED graphite K lm - CRI LED 62W= 4kV 104W=4kV 145W=4kV SURGE cd/klm 120 LED 168 LED 2883 Saturno - wide beam wattage colour weight code code W K - ølm - CRI LED graphite K lm - CRI 80 LED graphite K lm - CRI 80 LED graphite K lm - CRI 80 SUSPENSION

5 356 Saturno LED - suspension cd/klm SURGE SURGE 139W=4kV 177W=4/6kV new lm ta -40 C +45 C LED Diffuser: in clear polycarbonate, LEDs with protective lenses Saturno - wide beam wattage colour weight code code W K - ølm (700mA) - CRI LED graphite K lm - CRI cd/klm Diffuser: in clear polycarbonate, LEDs with protective lenses Saturno HP - wide beam CLD CELL-D CLD CELLD-E LED (Tj=25 C) wattage colour weight code code W K - ølm (850mA) - CRI LED graphite K lm - CRI 80 Standard: driver can work also with DC so that Saturno can be used as an emergency fixture with centralized power supply.

6 Saturno LED - suspension 357 RITOCCO LED 62W= 4kV 104W=4kV 145W=4kV SURGE elliptical beam 1250 cd/klm 120 LED 168 LED EL FL FS 2884 Saturno - elliptical beam wattage colour weight code code W K - ølm - CRI LED graphite K lm - CRI 80 LED graphite K lm - CRI 80 LED graphite K lm - CRI 80 Ideal version for warehouses and storage shelving. To be used with acc SUSPENSION