Micro Molds Case Study: Micro Mold for Medical Component By Justin McPhee, VP Engineering, Mold Craft, Inc.

Transcription

1 Micro Molds Case Study: Micro Mold for Medical Component By Justin McPhee, VP Engineering, Mold Craft, Inc. The Challenge: Molding a pipette shaped part with a.015 wall x.372 long followed by a.008 wall x.100 is challenging enough by most mold and molding standards. Add to that molding these micro parts from VICTREX PEEK 90G (polyetheretherketone) material, selected for its high strength properties needed by the customer, and the challenge is even greater. Now, how about doing this in a 4 cavity mold? An 8 cavity mold? Can a Cpk of 1.33 be achieved on this wall section? These are the challenges and questions Mold Craft set out to address when a customer came to them with this medical funnel tip component. However, this project could not have been accomplished successfully without Mold Craft s partners in mold fill/material flow simulation, Meltflipper technology and a molding press designed for micro molding. As a complete solutions provider, Mold Craft Inc. has built a reputation for its ability to engineer, design and manufacture high cavitation production molds for high volume part applications (in the millions per run). However, Mold Craft has also received recognition for the ability to build injection molds with extremely tight tolerances to accommodate molding of micro parts with intricate geometries that require high Cpk values. Recently Mold Craft was approached by a customer whose challenge was just that: micro medical parts shaped like a pipette called the funnel tip with an extreme length to wall thickness ratio. Mold Design Challenges: The Mold Craft Design Center took on this project that was originally designed to be a single cavity bridge or prototype tool that evolved into a production mold requiring at least four cavities, and possibly eight cavities to meet the customer s increasing production requirements. First, Mold Craft created a preliminary design model and mold layout to be used at the heart of the collaborative efforts via WebEx with the customer. The design package consisted of fully detailed and toleranced prints which have proven to be the key to manufacturing completely interchangeable components that do not require fitting when installing in the mold. The design department is critical to the manufacturing process as they design for manufacture based on the Erowa work holding and palletization system. The mold design itself needed to be flexible to accommodate a single cavity that would evolve to 4 and eventually 8 cavities, depending on the results of the simulation and actual testing. This flexibility was achieved by using an adequately sized mold base that would allow for the addition of cavities as the customer s volumes increased. Interchangeable cavity inserts could be added at a later date to minimize the turnaround time for the additional cavities and insure splits that allowed for adequate venting, and the ability to modify the molding geometry if needed. Due to the extremely high melt flow of the PEEK material the customer needed for this part, Mold Craft decided to begin with a single cavity prototype in a mold base scaled and set up to eventually accommodate eight cavities. While expanding to 4 and 8 cavities, the Mold Craft design engineers realized this micro sized, dual gated funnel tip may have serious melt balance issues both within the cavity and between cavities. The need to balance the runner and parts to ensure dimensionally accurate parts (given the extremely small dimensions), was essential to the quality of the funnel tip. 1

2 During the design phase Mold Craft saw that the runner and gate system would be critical to the success of the project. Mold Craft recognizes that the industry standard of a naturally balanced or geometrically balanced runner for this application could result in shear induced melt variation. This condition could develop in the runner system that would result in different melt conditions feeding different cavities and different regions of a cavity. This could result in cavity to cavity material and filling variations as well as variations within each of the double gated parts. A best case scenario with these conditions is delayed product start up, process development and a narrow process window. Worst case is a product that cannot be molded, or molded only with high spoilage. The thermal variations developed in a conventional runner can be seen in Figure 1 (Note: there is over a 100F melt temperature difference between the yellow and red regions in the Moldflow 3D simulation. Figure 1 To ensure proper balance, Mold Craft enlisted Beaumont Technologies, developer of the patented MeltFlipper technology, early in the mold design process in order to mitigate the effects of shear induced melt variations that develop in all runners and to assure that the cavities could be filled completely. MeltFlipper technology was developed to manage shear induced material and flow variations which lead to problems such as flash, short shots, long cycle times and high scrap rates. Optimizing the mold design helped insure that the melt delivery system (runner and gates) and process would minimize the risks of quality issues in molding the critical features of the plastic part. The thin tip region of the part was a particular focus. A filling and rheological balance was critical in order to assure consistency between parts, eliminate core shift, eliminate hesitation effects and generally maximize the molding process window. Beaumont s melt management technologies, including MeltFlipper, were determined to be the best means to deal with the thermal, shear and filling imbalance found in all runners. This technology was designed into the runners for each of the prototype and production molds. 2

3 To ensure an optimum runner and gating design as well as mold fill and balance, Beaumont also conducted a mold filling simulation for Mold Craft using their proprietary VeriFlo program and Autodesk s 3D injection molding simulation program (Moldflow ). The combination of simulation and VeriFlo would assure the parts could be filled with the widest process window possible. Beaumont s VeriFlo material flow characterization program is used to benchmark actual molding conditions vs. simulation predictions. With all injection molding simulation programs, a certain amount of error should be expected. After all they are simulation not reality. The more demanding an application, the higher the risk, and because this project truly challenged the limits of the injection molding process, Mold Craft wanted the best possible analysis. The real world molding feedback provided by Beaumont s VeriFlo helps assure maximum benefit when using injection molding simulation for demanding applications such as our customer s small, thin walled, PEEK medical device part. Molding Processing Challenges: Beaumont s VeriFlo provided Mold Craft with the answers to all of these challenges by providing real world molding information to the analyst. VeriFlo begins with molding the subject plastic material in a specially designed flow characterization tool/mold that includes a wide variety of runner and cavity like flow geometries. Specially designed data acquisition equipment very accurately captures the melt s reactions when processed through a matrix of these geometries, injection rates, mold and melt temperatures. Beaumont s CAE engineers then perform an injection molding simulation through each of the pre modeled flow characterization tool/mold geometries using the exact conditions as those recorded during actual molding. The results of the simulations and actual runs are then compiled and processed. The CAE engineers can then use this information while analyzing a project mold thereby improving performance and minimizing risk. Using the single cavity prototype, the mold filling simulation and analysis to verify the performance, Mold Craft was able to ensure that the part design, mold and molding conditions would be optimum for producing this micro part in a production molding environment. Simultaneously a 4 cavity and 8 cavity simulation was also produced. With the increase of the mold from a single cavity prototype mold to a 4 cavity production mold, the project took a turn that would require extremely tight tolerances of the part geometry to ensure high Cpk. In addition, it would need an advanced runner design to deliver the VICTREX PEEK 90G material to all cavities evenly, given the extremely thin wall section (0.008 ) so that these very small parts could be molded consistently and repeatedly fill the micro parts that are at the bottom x.472 long x at the tip. The runner cutaway of a mold filling analysis predicted a melt difference of over 70 o F would develop across the runner feeding different cavities. Beaumont Technologies determined that the differences were even more severe as all filling simulation programs under predict the actual filling imbalances. Note that not only are the different cavities receiving different melt conditions, but the melt temperature at each of the two gates feeding the inside four cavities is significantly different. Figure 2 shows the final runner design and analysis which included MeltFlipper technology. Note the sideto side variations in all of the runners have been eliminated. Each cavity and gate is receiving the same melt conditions. The design has provided for not only a filling balance but a rheological balance as well. This will result in the maximum process window possible. 3

4 Figure 2: Figure 3 is a view of the melt temperature distribution within the full eight cavity mold after the patented MeltFlipper is applied. Note all gates and cavities are now fully balanced and receiving the same melt temperature. Figure 3: Mold Craft completed the design phase of the project using the recommendations from Beaumont Technologies, engineering the single, four and eight cavity design packages. Collaborating on the design with Mold Craft management gave our customer confidence that this small, intricate part could indeed be successfully molded. The design was sent to Mold Craft s Manufacturing Center to produce the mold. Using precision CNC high 4

5 speed mills, CNC wire and sinker EDM s the designs came to life. Specializing in high precision multi cavity molds, Mold Craft insured productivity by using a pallet fixture system along with advanced automation to produce exacting precision intricacy while reducing costs for their client. Molding Machine and Material Requirements Challenges: Because of the size and complexity of the part and the mold, Mold Craft next needed a molding machine that could produce the part. Mold Craft contacted Sodick Plustech, known for its ultra precision injection molding machines, to discuss the project. We determined that the newly released 20 ton Plustech LP20EH2 Micro Molding series with a 12mm diameter plunger would be ideal for the application. The LP20EH2 was developed due to market demand for fine pitch connectors and other thin wall micro featured components. This LP series uses Sodick s proprietary Linear Motor Driven Servo Valve that can inject at a speed of 1,300 mm/second (51.1 /sec.) translating to an acceleration of 15.3G. Sodick Plustech s Micro Molding series has been extensively evaluated by precision molders in the US, especially those who mold medical device components. Sodick Plustech advises this new series will undoubtedly open a variety of opportunities in the more complex and intricate thin wall designs which are currently not moldable or require a secondary machining operation. Figure A. Base Process with Pack/Hold Stage Figure B. 800mm/sec Injection Velocity Process 5

6 LP20EH2 was able to fill this thin wall micro molding application with a robust process. The runner system was well balanced and the part features including wall tips were filled without flash. Sodick Plustech did a process window study on this mold and found that the mold accepts from 100mm/sec to 800mm/sec injection velocity. This wide process window will provide our user to validate a robust process. The Results: Challenges accepted, problems solved and parts delivered. More about Mold Craft Mold Craft, Inc. was established in 1964 to design and build injection molds. We specialize in building High Volume, Multi Cavity, and Multi Mold projects that produce small, intricate, precision plastic, silicone, ceramic, and metal molded parts. Mold Craft s strength is in designing and building molds that require extensive engineering, tightly toleranced CNC Machining, CNC Sinker and Wire EDM work, Grinding, and Polishing. Polishing is done in house to maintain best control over quality. Design work is done using Solid Works. Mold Craft, Inc. was the AMBA 2008 Mold Builder of the Year and MoldMaking Technology Lead Time Leader for More information is available at craft.com. More about Sodick Sodick Plustech (Yokohama, Japan) is a global supplier of high precision injection molding machines. The company developed its own design of V LINE Two Stage Plunger Style injection molding machines in Sodick Plustech offers horizontal machines (thermoplastic, LSR) from 5 ton 650 ton and vertical machines (thermoplastic, LSR) from 20 ton 150 ton. More information is available at inc.com. 6

7 More about Beaumont Beaumont Technologies (Erie, PA ) is a plastics engineering firm and technology/service provider to the plastics industry. The company is the pioneer and world leader in the science of controlled rheology and morphology as applied to the formation of plastic products in a mold. With a focus on injection molding, Beaumont s global activities includes application of its patented rheological control technologies (including MetFLipper technologies), injection molding simulation services, providing engineering training courses and advanced material characterization using its patent pending ThermaFlo and proprietary VeriFlo methodologies. Additionally the company maintains a strong R&D program, an advanced polymer processing lab as well as product and process development services. More about Victrex Victrex Polymer Solutions is exclusively focused on the development, manufacture and sale of high performance polyaryletherketone based products such as VICTREX PEEK polymer, APTIV Films, VICOTE Coatings, VICTREX Pipes, and VICTREX PEEK polymer for Composites. This advanced polymer product family includes standard pellet and powder grades for injection molding, compression molding, and extrusion, as well as specialty compounds to meet your application designs and developments. For over 30 years, Victrex has consistently delivered quality products and services to customers globally. More information is available at More about Justin McPhee Justin has been with Mold Craft, Inc for 13 years coming up through the Design Group and is now one of two owners of Mold Craft and serves as their VP of Engineering. McPhee graduated from the North Dakota State University in Fargo, North Dakota with a degree in Mechanical Engineering. Mold Craft s mission as a moldmaker is to not only keep up with technology but to lead the way in supporting medical device manufacturers through investment, innovation, and collaboration. # # # 7