Installation Guide The neo Plateau Rooflight Installation Guide

Transcription

1 Installation Guide The neo Plateau Rooflight Installation Guide > a roof window suitable for flat roofs between 3 and 10 March 2018 Contents (supplied with rooflight) The neo Plateau Rooflight M10 washer x 8 M10 x 50mm coach screw x 8 Tools / Materials Required (supplied by installer) Skeleton gun & low modulus neutral cure silicone Drill & drill bits 17mm Socket wrench Assorted packers

2 * This is a suggested installation detail which may not be exactly applicable to all situations and constructions. It is not a detailed or constructional proposal. Installers and designers are advised to check their own details for compliance with all currently applicable Local Authority by-laws, Acts of Parliament and British / ISO standards. (applied to glass) All information contained within this drawing is copyright and design right of the Rooflight Company. The intellectual property rights of the products detailed within this drawing and embedded 3D models are owned by the Rooflight Company. w: t: e: info@therooflightcompany.co.uk Preparation Prepare the kerb in accordance with the roof type referencing the appropriate installation detail and BS6229:2003 Flat roofs with continuously supported coverings - Code of practice. Just prior to installing the rooflight, lay a thick continuous bead of low modulus neutral cure silicone (supplied by the installer) around the perimeter of the kerb SECTION 1a 2 A 1 Low Profile Height 102 1b 1c 125 Black Border A B d Kerb Height To Be Determined By Installer* 1 B C Roof Covering* Structural 3 Kerb Width* Insul.* Internal Finish* Typical Kerb Width 125 Clear Viewable Finished External Kerb Installation Pitch SCALE 1 : A3 - mm C *1 - This detail does not specify kerb height. We recommend that installers follow the guidance outlined in BS6229:2003 Flat roofs with continuously supported THERMAL PERFORMANCE U-Value 1.3w/m²Kº NOTES All installation components contractor supplied except part 1a to 1d (factory fitted), 3 (factory fitted) & 4 (supplied loose). Key: 1. neo Plateau Rooflight 1a. Perimeter silicone weather-seal. 1b. Internal air-seal. 1c. IGU (6.4mm clear laminate, 20mm argon filled cavity, 6mm low-emissivity toughened outer). 1d. Thermoliner thermal and moisture control. 2. Perimeter silicone seal seal perimeter of rooflight (1) with a thick continuous bead of low modulus neutral cure silicone. D 3. Localised fixing lug (part of roofight frame). D 4. Internal fixing - M10x50 A2 stainless steel coach screw & washer. 5. Fixing tolerance pack any gap behind the fixing lug prior to bolting up the coach screw (4). 6. Insulation. 7. Vapour barrier sealed to the underside of the Thermoliner (1d). 8. Internal finish hardwood timber recommended. Calculated in accordance with BS EN ISO and BS EN 673 based on roof opening area of m² for the rooflight only using a centre 9. Structural member. pane ug value of 1.0W/m²K. 10. Finished roof covering TITLE : DWG NO. : neo Plateau Rooflight SCALE : > A rooflight range suitable for flat roofs between 3 and 10 Single-ply membrane / felt installation detail SHEET NO. : NP-001INST-C 1 OF 2 A3 DATE : 24/07/2017 DO NOT SCALE REVISION: C DB : NT CB : PD 1

3 The neo Plateau Rooflight placement Lower the neo Plateau Rooflight down over the kerb. Ensure it is located centrally with a 10mm gap all around. Once central, bed the neo Plateau rooflight down into the silicone. 10mm 2

4 Fixing your Rooflight Locate the eight internal fixing lugs and drill pilot holes suitable for the supplied M10 coach screws and washers (supplied) specified for use into timber kerbs. Pack any gaps behind the fixing lugs with a suitable packer (supplied by the installer), then fix the M10 coach screws and washers. If installing the models compliant with Part Q the following fixings for different kerb materials must be used (supplied by the installer): Concrete Rawlbolt Shield Anchor M10 10L Steel M10x50 A2 Stainless Steel Torx button head machine screw with A2 stainless steel washer and A2 stainless steel Nylok nut. Fixing lug 3

5 Insulated Kerb Affix insulation to the kerb locating it up to the underside of the Thermoliner (white plastic trim). 47mm Thermoliner There is a 47mm space to be filled by the insulation and the internal finish (based on a 75mm structural member). Depending on the type of insulation this might need to be notched around the localised fixings. 4

6 Vapour Barrier Seal the vapour barrier to the underside of the Thermoliner (white plastic trim). Vapour Barrier 5

7 Internal Finish Affix the internal finish up to the underside and flush with the edge of Thermoliner (white plastic trim). We recommend a hard wood timber lining. Hard wood timber lining Insulation This completes the installation of the neo Plateau Rooflight. 6

8 CARE & MAINTENANCE To achieve the maximum service life from the neo Plateau Rooflight it is important that scheduled care and maintenance is undertaken. Please note that the guarantee will become void if the procedures outlined in the separate maintenance manual are not adhered to. Refer to Operations & Maintenance Guide. ADVISORY Standard roof window. All the information provided in this document refers to a standard specification the neo Plateau Rooflight. Install in accordance with national building regulations/codes. This manual is an installation suggestion and installers should verify fitness for purpose in accordance with all applicable regulations / standards at time of installation. Install in accordance with this manual: The Rooflight Company cannot accept any liability if the neo Plateau Rooflight is not installed strictly in accordance with the instructions contained in this manual and implicit in the Suggested Installation Details. Structural support: Structural supports for the neo Plateau Rooflight are to be designed and supervised during construction by the roof window installer or project Structural Engineer. Nothing in this manual constitutes a structural proposal. Sizing / positioning of structural supports should be determined by the projects suitably qualified structural engineer. To download this manual as a PDF visit The Rooflight Company Wychwood Business Centre, Milton Road, Shipton-under-Wychwood, Oxfordshire OX7 6XU Tel: info@therooflightcompany.co.uk MANAGEMENT SYSTEMS RECYCLE In the interest of continuous product development. It may be necessary to amend specification without alteration to technical literature. All drawings and designs are the copyright and design right of the Rooflight Company. NP-100INST-A