TS110 Visible (exposed) fixing with screws on an aluminum sub-frame

Transcription

1 TS110 Visile (exposed) fixing with srews on an aluminum su-frame This system offers a ost effetive solution for installing Trespa panels in a large variety of panel dimensions. Trespa Meteon panels with a minimum thikness of 5/16 inh* (8 mm) may e fixed onto an aluminum su-frame. This su-frame must onsist of vertial extrusions of suffiient strength. Fasteners an e finished to math the panel (availale in a wide range of Trespa olors through third parties). > Kelly Residene, USA > Arh. Aramson Teiger Arhitet This doument is intended to provide general reommendations only. Trespa provides these guidelines and all testing, ode and design data for informational purposes only and strongly advises that the ustomer, projet owner and arhitet seek independent advie from a ertified onstrution professional and/or engineer regarding appliation and installation as well as ompliane with design requirements, appliale odes, laws and regulations, and test standards. Please hek your loal odes and appliale design requirements for proper use. * Note that due to onversion, the value provided is approximate. 1 Please hek for the latest version of this doument

2 Overview of availale ertifiates and test reports To onsult the full details of availale ertifiates please visit For TNA systems that meet the performane riteria of the NFPA 285 or ULC S134 multistory fire test standard, refer to design details indiated with a 285 or 134. General installation details Cavity depth and ventilation (Free air avity) The free air avity depth etween the akside of the panel material and the fae of the weather resistive arrier is 1 inh (25 mm*). This free air avity allows for amient air to flow through from the ventilation inlets and outlets. Ventilation perforations must allow for a minimum opening of 2.36 square inhes per linear foot* (50 square m per linear meter) over the whole façade. Cavity depth as well as ventilation inlets and outlets must e in aordane with appliale uilding standards, regulations and ertifiates. To retain panel position, eah panel must have one fixed point in the enter of the panel. Diameter of panel fastener holes: 防 inh* (5.5 mm) for fixed holes 防 inh* (8.5 mm) for oversized holes Srews should e entered in the holes and not over tightened. Fixed Hole Oversized Hole Su-frame Trespa Meteon panels must e installed on a su-frame, omprised of aluminum extrusions, of suffiient strength and permanent duraility. Quality and/or treatment of the su-frame must e in aordane with appliale uilding standards, regulations and ertifiates. Fixing detail Trespa Meteon panels with a minimum thikness of 5/16 inh* (8 mm) may e fixed onto an aluminum su-frame with fasteners (availale in a wide range of Trespa olors through third parties). Fasteners onneting the panels to the su-frame must e #12-11 stainless steel srews and are typially 1 inh (25 mm*) in length. ode V3076 version 2.0 date * Note that due to onversion, the value provided is approximate. Please hek for the latest version of this doument

3 Overview of tehnial installation details AutoCAD drawings for TS110 are availale at Trespa panels Panel olor/deor Panel thikness Non-Trespa omponents/geometry to ladding Free air avity (ak fae of panel to the weather resistive arrier) Aluminum profiles Weather resistive arrier Uni olors, Metallis, Wood Deors, Naturals 5/16 inh* (8 mm), 3/8 inh* (10 mm), 1/2 inh* (13 mm) 1 inh (25 mm*) (as required per strutural design) Undefined Tehnial installation details Panel thikness Panel thikness inh* mm 5/16 8 3/8 10 1/2 13 Maximum panel dimension Max. panel dimensions inh* mm 120 x x 1860 Joint width Joint width inh* mm 3/8 10 Based on appliale uilding standards, regulations or ertifiates, wider joints may e permissile. Edge learane Edge learane inh* (mm) Minimum 3/4 (20) inh* and (20 maximum mm) and 10 maximum x panel 10 thikness, x panel ounted thikness, from ounted the enter from of the the enter first of fixing the first fixing * Note that due to onversion, the value provided is approximate. 3 Please hek for the latest version of this doument

4 Reommended maximum fixing distanes Maximum fixing distanes BA Panel Thikness for Satin / Rok / Matt Panel Thikness for Gloss CB inh* mm inh* mm inh* mm inh* mm inh* mm 5/16 8 3/8 10 1/2 13 3/8 10 1/ fasteners in one diretion or more fasteners in one diretion A The maximum permitted fixing distanes shown have een designed with a maximum (wind) load of 20 pounds per square foot (psf) and a maximum defletion riteria of L/175. B Based on the surfae properties of Gloss panels, fixing distanes are redued. Fixing distanes must e alulated in aordane with appliale loal standards, regulations and ertifiates and should e verified y a strutural engineer. For more information aout defletion and wind loads, please visit a = horizontal fixing distane = vertial fixing distane = edge learane = fixed point in panel entre = sliding point a a a ode V3076 version 2.0 date * Note that due to onversion, the value provided is approximate. Please hek for the latest version of this doument

5 6 7 TS110 Horizontal ross-setion Interior sheathing** 2. Thermal insulation** 3. Steel stud** / aking plate** Interior Exterior sheathing sheathing** * 2. Thermal insulation * 3. Steel stud* / aking plate * 4. Exterior sheathing * 5. Weather arrier (vapor permeale)* 6. Ventilated avity** 6. Ventilated avity 7.Hat hannel Hat hannel** 8. J-hannel 9. Channel anhor * 8. J-hannel** 10. Trespa Meteon panel 11. Panel fastener 5. Weather arrier (vapor permeale)** 9. Channel anhor** * not y Trespa 10. Trespa Meteon panel 11. Panel fastener** ** not y Trespa TS110 Horizontal ross-setion Please hek for the latest version of this doument

6 TS110 Vertial ross-setion 1. Interior sheathing** 2. Thermal insulation** 3. Steel stud** / aking plate** 4. Exterior sheathing** 5. Weather arrier (vapor permeale)** 1. Interior sheathing * 2. Thermal insulation * 3. Steel 6. stud* Ventilated / aking avity** plate * 4. Exterior sheathing * 5. Weather arrier (vapor permeale)* 6. Ventilated avity 7. J-hannel 8. Channel or Hat hannel anhor** 8. Channel anhor * 9. Trespa 9. Trespa Meteon Meteon panel panel 10. Panel fastener 11. Vent sreen 7. J-hannel or Hat hannel** 10. Panel fastener** 11. Vent sreen** * not y Trespa ** not y Trespa ode V3076 version 2.0 date Please hek for the latest version of this doument TS110

7 Dislaimer This is a print generated y you from ( Wesite ). By aessing the Wesite and printing this doument you have aepted the Terms of Use of the Wesite. Please refer to the Wesite for all onditions that apply to this doument. Not all the systems shown in this doument may e suitale for all appliations and jurisditions. We provide you with testing, ode and design data for informational purposes only and strongly reommend that you or any other user of this doument otains independent advie regarding ompliane with design requirements, appliale odes, laws and regulations, and test standards. Please hek your loal odes and design requirements for proper use. Trespa will not aept any liaility in relation to your use of this doument. All intelletual property rights, inluding opyrights and other rights regarding the ontent of the Wesite and this print generated from the Wesite (inluding logos, trademarks, servie marks, software, dataases, audio, video, text and photographs) are owned y Trespa and/or its liensors. Trespa, Meteon, Izeon, Athlon, TopLa, TopLa PLUS, TopLa ECO-FIBRE, Virtuon, Volkern, Trespa Essentials and Mysti Metallis are registered trademarks of Trespa. All oral and written statements, offers, quotations, sales, supplies, deliveries and/or agreements and all related ativities of Trespa are governed y the Trespa General Terms and Conditions of Sale (Algemene verkoopvoorwaarden Trespa International B.V.) filed with the Chamer of Commere and Industry for Noord- en Midden- Limurg in Venlo (NL) on 11 April 2007 under numer ,whih an e found on and downloaded from the Trespa wesite, All oral and written statements, offers, quotations, sales, supplies, deliveries and/or agreements and all related work of Trespa North Ameria, Ltd. ode V3076 version 2.0 date are governed y the Trespa General Terms and Conditions of Sale, whih an e found on and downloaded from the Trespa wesite, A opy of these general onditions of sale will e provided free of harge on request. 7 Please hek for the latest version of this doument