Addendum No. 1 DELETE; TABLE OF CONTENTS "SHELVING & CLOSET HARDWARE" REVISION; DOOR HARDWARE - see attached revised Specifications.

Transcription

1 SPUR DESIGN March 22,2012 Waldrop Construction, Inc. Construction Manager One Santa Fe Plaza, Suite 101 Oklahoma City, OK RE: ELLIS COUNTY MULTI-PURPOSE BUILDING Addendum No. 1 Item No. 1 CLARIFICATION; TABLE OF CONTENTS to read "08331 Item No. 2 Item No. 3 DELETE; TABLE OF CONTENTS "SHELVING & CLOSET HARDWARE" REVISION; DOOR HARDWARE - see attached revised Specifications. Item No. 4 CLARIFICATION; SHEET A101, There are (2) - Plastic Laminate Benches in the Men's and (2) - Plastic Laminate Benches in the Women's Dressing Room. Item No. 5 Item No. 6 Item No. 7 CLARIFICATION; SECTION millwork to have 176 degree concealed hinges. CLARIFICATION; SHEET AS101, The Retaining Wall to be 76'-0" in total length and 4'-0" in height. CLARIFICATION; Kitchen Equipment List is as follows: (1 )-Commercial 4 burner gas range w/electric oven (Thermador Pro Harmony) (l)-commercial Refrigerator (True Series) (1 )-Commercial UP-Right Freezer (Electrolux) (l)-commercial Convection Electric Oven (Hobart Series) (2)-Undermount Convection Microwaves (1 )-Commercial Mixer (Hobart Legacy Series) (l)-commercial Range Hood (Ansul) (1 )-Commercial Holding Cabinet (Hobart HHC) These are all found in Appendix "A" Y U K O N O K L A H O M A W W W. S P U R - D E S I G N. C O M

2 Item No. 8 Item No. 9 CLARIFICATION; SHEET A101 - Distance from face of existing building located to GRID "A" to be 2'0". CLARIFICATION; Mirrors in the men's and women's bathrooms are 18" x 36" in size and there are a total of (4). END OF ADDENDUM NO. 1 Y U K O N O K L A H O M A W W W. S P U R - D E S I G N. C O M

3 FINISH HARDWARE SECTION PART 1 - GENERAL 1.01 WORK INCLUDED: A. The work to be done under this specification consists of furnishing and delivering to the General Contractor, at the building, all Finish Hardware. B. Hardware for interior and exterior doors, other than specified in specific door sections WORK NOT INCLUDED: A. Rough hardware is not a part of this section of the specifications. General Contractor to furnish and set all items that are specified or necessary for a complete job, and all hardware specified in other sections. B. Hardware for the following items are not included under this section: Metal windows, metal screens and access doors. C. Installation by General Contractor RELATED WORK: A. Section 08110: Steel Doors and Frames B. Section 08210: Wood Doors C. Section 08410: Aluminum Doors and Frames 1.04 QUALITY ASSURANCE: A. This material shall be procured from a source of supply approved by the Architect as competent to correctly interpret the plans, details and specifications, and be prepared at all times to promptly and satisfactorily service the hardware on the job. This supplier must be an established Contract Builders' Hardware firm, who maintains and operates an office, display room and stock in the State of Oklahoma. This material must be furnished by or under the direct supervision of an Architectural Hardware Consultant, as certified by the Door and Hardware Institute, Inc., regularly employed by this supplier, and all bids must be so certified. Bids on this material will not be acceptable from firms who have not been successfully engaged in selling and servicing Contract Builders' Hardware for a period of at least five (5) years. B. Hardware has been specified herein by manufacturers' name, brand and catalog 1

4 number for the purpose of establishing a basis for quality, finish, design and operational function. C. If hardware for any particular door is not listed or described, it shall be furnished and shall be as specified for similar locations. D. Quantities shall be determined by the bidder FIRE RATED DOORS: A. Comply with requirements of NFPA 80 and Life Safety Code NFPA 101. B. Provide hardware which has been tested, listed and bears UL Label SUBMITTALS: A. Submit to the Architect five (5) complete typewritten copies of the hardware schedule for approval. The schedule shall be prepared using the "Sequence and Format" for the Hardware Schedule as recommended by the Door and Hardware Institute (DHI). B. Schedule shall follow requirements of Specifications and shall indicate types, manufacturer's name and number location and finish of each item required. C. Submit such samples as required by the Architect for approval. Do not deliver hardware until approval is obtained. D. Approval of schedule will not relieve Contractor of responsibility for furnishing all necessary hardware. E. Templates: Provide necessary templates and/or physical hardware to all trades requiring them in order that they may cut, reinforce or otherwise prepare their material or protect to receive the hardware item DELIVERY, STORAGE AND HANDLING: A. All items of hardware to be delivered to the job site shall be completely packaged with all necessary screws, bolts, miscellaneous parts, instructions and where necessary installation templates for manufacturers' suggested installation. They are to be clearly labeled so as to conveniently identify them and their intended location in the building. B. Store in secure lock up. Control both before and during installation. C. Protect original finish and texture of all finish hardware items, both installed and not-yet-installed. Follow respective hardware manufacturer's instruction; use protective materials and methods recommended by manufacturer WARRANTY: 2

5 A. The finish hardware shall carry a limited warranty against defects in workmanship and operation for a period of one year from date of acceptance. No liability is to be assumed where damage or faulty operation is due to abuse, improper usage, improper installation or failure to exercise normal maintenance PRODUCTS: 2.01 HARDWARE: 2.02 FINISH: Locks shall have a one year limited warranty. Door Closers shall have a ten year limited warranty. Exit Devices have a three year limited warranty. A. Provide items as listed in Schedule at end of this Section, complete to function as intended. B. Substitutions: Request for substitutions of items of hardware shall be made to the Architect no later than ten days prior to bid opening. Approval of substitutions will only be in writing or by addendum. Request for substitutions shall be accompanied by samples and or detailed information as to the manufacturer of the product. C. Items specified "NO SUBSTITUTIONS" shall be provided exactly as listed in this Specification. A. All hardware throughout shall be Satin Chrome (626 or 652) finish. Door Closers stock painted to match KICK PLATES: 2.04 KEYING: A. Kick Plates to be ten inches high, full width of door less two inches. Stainless Steel, beveled Three sides,.050 gauge material. A. All locks & cylinders two keys each, keyed alike or keyed Different as directed by the architect. Master keyed in one set for project. B. Supply two (2) keys for each Cylinder. C. Supply Six (6) Master keys MANUFACTURERS SCHEDULED: G - Glynn Johnson L - LCN Door Closers 3

6 HARDWARE SETS: P - PBB Hinge Company R - Rockwood Manufacturing SC - Schlage Lock Company V - Von Duprin, Inc. Doors: 100A, 100B,100C SET #1 6 Ea. Hinges 4B x 4.5 x 652 x NRP P 1 Key Removable Mullion KR4954 x SP28 V 1 Cylinder x 626 SC 1 Exit Device 99L x 626 V 1 Cylinder x 626 SC 1 Exit Device 99L-DT x 626 V 2 Closer 4041-H Cush x AL x TB L 2 Kick Plates K x D.W.-2 x 630 R 2 Stops 471 x 626 R 1 Set Weatherstrip 306AV (Head & Jamb) PE 2 Door Bottoms 315CN x D.W. PE 1 Threshold 171A x D.W. PE 1 Mullion Seal 5100N x D.H. PE Doors: 101,105A SET #2 3 Ea. Hinges BB x 4.5 x 652 P 1 Lockset AL53PD-SAT x 626 SC 1 Stop 440 x 626 R 3 Silencers 608 R 4

7 SET #3 Doors: 102,106A, 106B 6 Ea. Hinges BB x 4.5 x 652 P 2 Flush Bolts 555 x 626 R 1 Dust Proof Strike 570 x 626 R 1 Lockset AL53PD-SAT x 626 SC 2 Overhead Stops 450S x 652 G 2 Silencers 608 R SET #4 Doors: 103,107 3 Ea. Hinges BB x 4.5 x 652 P 1 Push Plate 70B x 630 R 1 Pull Plate BF110 x 70B x 630 R 1 Closer 4041-RW/PA x AL L 1 Kick Plate K x D.W.-2 x 630 R 1 Wall Stop 409 x 630 R 3 Silencers 608 R Door: 105C SET #5 All hardware by door supplier. Door: 105B SET #6 3 Ea. Hinges 4B x 4.5 x 652 x NRP P 1 Mortise Lockset w/ Deadbolt L9470P-06a x 626 SC 1 Closer 4041-H Cush x AL x TB L 5

8 1 Kick Plate K x D.W.-2 x 630 R 1 Stop 471 x 626 R 1 Set Weatherstrip 306AV (Head & Jamb) PE 1 Door Bottom 315CN x D.W. PE 1 Threshold 171A x D.W. PE PART 3 - EXECUTION 3.01 INSPECTION: A. Examine hardware prior to installation; verify that delivered hardware matches quantity, type, finish, etc., as that shown on final Hardware Schedule. Notify Architect and hardware supplier, in writing, of discrepancies, shortages and incorrect hardware items. B. Provide or replace shortages and incorrect hardware with proper hardware as scheduled on final Hardware Schedule, at no cost to Owner INSTALLATION: A. Mount hardware at height recommended by NBHA "Recommended Location for Builders' Hardware", except as otherwise specifically indicated or required to comply with requirements of governing authorities having jurisdiction at project site as directed. B. Install all hardware in compliance with manufacturer's instruction requirements. C. Set hardware level, plumb and true to line and location required. Adjust and reinforce attachment substrate as necessary for proper installation and operation. D. Attach hardware securely in final position. 1. Attach exit devices, closers and holders to doors with through bolts and grommet nuts. E. Cut and fit thresholds to profile of door frames ADJUSTING AND CLEANING: A. Check and adjust each operating item of hardware to operate freely and easily, to ensure proper operation and function of each unit. 1. Lubricate moving parts with type lubricant recommended by manufacturer, if required by manufacturer. 2. Replace units which cannot be adjusted and lubricated to operate freely and 6

9 smoothly as intended for application made, at no cost to Owner. B. Clean each hardware item as necessary to restore original factory finish and surface texture, as recommended by manufacturer. Replace units which cannot be satisfactorily cleaned to restore factory finish and texture, at no cost to owner. 7