R-MER LOC DELIVERY PROGRAMME R-MER. metal roofing systems

Transcription

1 DELIVERY PROGRAMME R-MER metal roofing systems

2 CHOICE FOR MATERIAL AND SURFACES EXPERIENCE VARIETY MATERIALS COLOUR COATINGS galvanized, polyester coated mill finish / stucco-embossed 0.7 / 1.0 mm RAL 3009 oxide red polyester coated 0.7 mm mill finish / stucco-embossed galvanized, polyester coated protective plating on both sides 1.0 mm RAL 6005 moss green AluZinc steel sheet with alu-zinc alloy Corrosion protection class III RAL 7016 anthracite grey galvanized, polyester coated polyester coated 0.7 mm Titanium-Zinc galvanized, polyester coated mill finish or pre-weathered 0.7 / 0.8 / 1.0 mm RAL 7024 graphite grey polyester coated 0.7 mm Copper TECU 0.6 mm RAL 7037 dusty grey galvanized, polyester coated galvanized, polyester coated RAL 8004 copper brown polyester coated 0.7 mm SPECIAL SURFACES polyester coated 0.7 mm Special colours and surfaces on request e.g. in aluminium: RAL 8014 sepia brown Patina Look galvanized, polyester coated Testa di Moro Zinc Look sheets delivered with protective film RAL 9002 grey white galvanized, polyester coated Stucco-embossed Patina Matt RAL 9006 white aluminium galvanized, polyester coated polyester coated 0.7 / 1.0 mm AluNatur available in several colour variations RAL 9007 grey aluminium galvanized, polyester coated polyester coated 0.7 / 1.0 mm Other colours, materials and surface finishes are available subject to minimum order quantities and lead-times. Prices available on request. Images are similar to the RAL colours mill finish, coated on both sides, sheet, galvanized coated on both sides Colour coating on both sides: Front side 25 µm RAL colours, rear side with protective coating (light coloured) 2

3 CONTENTS RIB-ROOF Evolution Overview... 4 Profiled sheets... 5 Fixing element (holding bracket)... 6 Ridge cap, closure, profile filler for top side, sealing tape... 7 Ventilation ridge cap, ventilation closure... 8 Cover sheet for verge, suspended profile, retaining / stopping plate... 9 Gutter inlet sheet / eaves panel, profile filler for rear side, eaves angle...10 Snow guard system, solar bracket / bracket for lightning protection, tread support, walkways...11 Page Accessories Soaker, vapour barrier membrane, accessories for installation, fall arrest system...12 Coil materials, flashings...13 R-MER metal roofing systems 3

4 RIB-ROOF EVOLUTION OVERVIEW Ridge cap 3 Profile filler - top side 5 Directional clip Closure 4 R-MER LOC 6 Eaves angle Gutter inlet sheet Video of R-MER LOC installation method with directional clips 200 on double Z-profiles Discover how to install R-MER LOC with straight profiled sheets and directional clips Video of R-MER LOC installation method with curved profiled sheets and turned directional clips 70 on double Z-profiles Discover how to install R-MER LOC with curved profiled sheets and turned directional clips Video of R-MER LOC installation method with directional profile 750 on rigid insulation boards Discover how to install R-MER LOC with directional profiles 750 on rigid insulation boards. Video of R-MER LOC installation method with directional profile 1500 on double Z-profiles Discover how to install R-MER LOC with directional profiles 1500 on double z-profiles. 4

5 PROFILED SHEETS Profiled sheets Construction width 500 mm profile height 67 mm CE-marking according to EN for steel and aluminium Weight (kg/m²) alu-zinc alloy galvanized and colour-coated, top side 25 µm polyester coating, rear side protective coating galvanized and colour-coated, top side 25 µm PVDF coating, rear side protective coating mill finish or mill finish and stucco-embossed mill finish and stucco-embossed with clear protective coating on both sides colour-coated, top side 25 µm polyester coating, rear side protective coating patina look Special colours and surfaces zinc look patina matt stucco-embossed mill finish EN 988 pre-weathered EN rear side protective coating 60 µm mill finish EN Special construction width 333 mm 400 mm up to 600 mm 67 Extras Extras for Description Fleece coating for anti-condensation sound absorption water absorption, up to 900 g/m² Tapered profiled sheets minimum construction width of 230 mm up to maximum width of 500 mm radius 5.00 m m convex radius > m convex Curving radius > m concave S-curving: convex/concave of tapered profiled sheets extra and over for a radius < m for cutting of straight ends Roll-forming at site lump sum for profiled sheet lengths of more than m Curving at site or for profiled sheets which are not transportable roll-forming at site Freight for over-length >14.60 m for curved profiled sheets Spreader beam incl. fixed crane hook, without belts R-MER metal roofing systems 5

6 FIXING ELEMENTS Fixing element (halters/clips) Description Packaging unit Turned clip 70 to be used with curved profiled sheets steel with alu-zinc alloy L= copper* L= *alternatively for copper profiled sheets: stainless steel clips 1.20 mm on request Directional clip 200 also for use as a fixed point steel with alu-zinc alloy L= Turned directional clip 200 also for use as a fixed point steel with alu-zinc alloy L= Directional profile 750 / 1500 / 2600 also for use as a fixed point with very long profiled sheets steel with alu-zinc alloy L= L= L= Turned directional profile 750 / 1500 / 2600 also for use as a fixed point with very long profiled sheets steel with alu-zinc alloy L= L= L= Wood screws self-drilling, full thread, from 80 mm partial thread, according to our European Technical Authorisation Description Usage Recess Packaging unit Panhead full thread for fastening of sliding clips to timber boarding, at least 24 mm for fastening of sliding clips to wooden lathing, at least 60 x 40 mm stainless steel 5.0 x Torx T x Countersunk screw full or partial thread for fastening wooden lathing to wooden substructure stainless steel 5.0 x Torx T x L to Countersunk screw partial thread for fastening wooden lathing to wooden substructure stainless steel 6.0 x Torx T x L to Drilling screws approved by building authorities and according to our European Technical Authorisation Description Usage Recess Packaging unit Flat headed screw for fastening of sliding clips on Z-profiles, light metal up to 1.3 mm stainless steel 5.5 x 25 Torx T Round-head screw without washer for fastening of sliding clips on Z-profiles, steel substructure 1.5 to 6.0 mm for fastening of sliding clips on Z-profiles, steel substructure 4.0 to 12.0 mm stainless steel 5.5 x Torx T x Hexagonal head screw with washer for fastening Z-profiles on Z-profiles or liners, component II up to 2.5 mm stainless steel 5.5 x 25 AF Countersunk screw for fastening of wooden lathing on trapezoidal profiles, steel substructure 0.75 to 1.50 mm stainless steel 6.0 x Torx T x L to Hexagonal head screw without washer for fastening of directional profiles (penetrating rigid insulation boards) on liners, steel substructure 0.63 to 1.5 mm stainless steel 6.5 x x L AF x L

7 RIDGE Ridge cap for warm roof construction maximum length 6.00 m 3 edges girth 312 mm girth 416mm girth 625mm alu-zinc alloy galvanized and colour-coated top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated top side 25 µm polyester coating, rear side protective coating mill finish EN mill finish EN Please include roof pitch when ordering ridge cap. Closure construction length 1540 mm girth 223 mm cover length 1500 mm alu-zinc alloy galvanized and colour-coated top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated top side 25 µm polyester coating, rear side protective coating mill finish EN mill finish EN Suspended profile for arris maximum length 6.00 m girth 223 mm alu-zinc alloy galvanized and colour-coated mill finish and stucco-embossed colour-coated mill finish EN mill finish EN Profile filler top side, sealing tape Application PE Foam profile filler top side, for ridge / closure 30 x profile filler stripe top side, for arris / suspended profile 30 x PUR Foam sealing tape impermeable to driving rain, vapour permeable, single side self-adhesive width 15 / R-MER metal roofing systems 7

8 VENTILATION RIDGE Ventilation ridge cap for cold roof construction Ventilation assembly set with integral ventilated closures (construction length 2030 mm), profile fillers and ridge cap (length maximum 6.00 m) construction height 80 mm, free ventilation section 450 cm²/m alu-zinc alloy galvanized and colour-coated top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated, top side 25 µm polyester coating, rear side protective coating mill finish DIN EN 988, rear side protective coating mill finish EN Please include roof pitch when ordering ventilation ridge caps. Ventilation closure construction length 2030 mm girth up to 443 mm length 2000 mm alu-zinc alloy galvanized and colour-coated top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated, top side 25 µm polyester coating, rear side protective coating mill finish DIN EN 988, rear side protective coating mill finish EN

9 VERGE Cover sheet for verge maximum length 6.00 m 5 edges additionally available as joint connector: girth 100 mm, up to 3 edges girth 312 mm girth 416 mm alu-zinc alloy galvanized and colour-coated, top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated, top side 25 µm polyester coating, rear side protective coating mill finish EN mill finish EN Extra: Extra: joint connector made out of steel sheet or aluminium joint connector made out of titanium zinc or copper Suspended profile maximum length 6.00 m girth 330 mm alu-zinc alloy galvanized and colour-coated mill finish and stucco-embossed colour-coated mill finish EN mill finish EN Retaining / stopping plate maximum length 6.00 m girth 125 mm 2 edges girth 250 mm 4 edges of material girth 125 mm girth 250 mm alu-zinc alloy galvanized and colour-coated mill finish and stucco-embossed colour-coated mill finish EN mill finish EN R-MER metal roofing systems 9

10 EAVES Gutter inlet sheet / eaves panel maximum length 6.00 m girth 312 mm 3 edges gutter inlet sheet eaves panel alu-zinc alloy galvanized and colour-coated top side 25 µm polyester coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated top side 25 µm polyester coating, rear side protective coating mill finish EN mill finish EN Please include roof pitch when ordering gutter inlet sheet or eaves panel! Eaves angle maximum length 6.00 m Packaging unit mill finish 40 x 20 x 2 6 lm Please use this order form for flashings: 10

11 ACCESSORIES Snow guard system Description /finish Packaging unit Snow guard pipe Ø32 mm with groove Solar pipe Ø32 mm with groove to enable fastening with groove stone/hammer-head bolt, e.g. for PV-moduls aluminium (max. length 6.00 m) lm aluminium (max. length 6.00 m) lm Snow guard bracket (2.0 pcs/m) construction width 120 mm for snow guard pipe/solar pipe Ø 32 mm with aluminium groove Ice stopper (4 pcs/m) constr. width 50 mm for locking aluminium Pipe connector for snow guard pipe/solar pipe outside aluminium Snow guard raising element Description Snow guard raising element for stable raising of the snow guard row, for photovoltaic systems by about 200 mm A finished snow guard raising element holds three snow guard pipes and needs two snow guard brackets. The distance of the snow guard rows according to our manual guide can be increased by 50 %. aluminium Solar bracket / Bracket for lightning protection Construction length 55 mm aluminium uncoated usable as bracket for lightning protection according to EN , testing category N Description Solar bracket / lightning protection preassembled with angles for solar modules aluminium Bracket for lightning protection for lightning protection aluminium, thickness 3 mm Tread support construction length 210 mm standard for roof pitches up to 15 higher pitches available on request Description Tread support adjustable for roof pitches of 0 up to 15 aluminium Angle bracket conical, for roof pitches < 30 aluminium Walkways roof pitches 0 30 Description /finish Walkway with anti-skid protection, incl. mounting accessories steel sheet galvanized, 250 x 600 mm steel sheet galvanized, 250 x L to 3000 mm _ Walkways also available as single steps or longitudinal walkways with balustrades. Manufactured in aluminium / aluminium die casting and steel galvanized aluminium die casting on request. R-MER metal roofing systems 11

12 ACCESSORIES Sanitary vent conical construction height 300 mm, available for different roof pitches Sanitary vent, conical for welding Sanitary vent, conical for sealing Cover with rosette for sanitary vent aluminium mill finish aluminium colour-coated for DN for DN for DN available on request for DN "Dense 7" Universal adhesive for DN and sealant, grey, 310 ml for DN Vapour barrier membrane Cold self-adhesive, 1.2 mm or 1.5 mm Finish technical data Cold self-adhesive elastomer bitumen vapour barrier membrane with glassfibre reinforcement 1.00 m x m 20 m 2 per roll, air layer thickness equivalent to diffusion sd = μ s [m] = 1500 [±10%] top side with polyester aluminium joint and silicone edge stripe, rear side with removable silicone film 1.2 mm mm Detailed data available on request Blind rivet / Cup blind rivet capsule: aluminium, spike: stainless steel A2 Description Usage Finish Packaging unit Blind rivet for riveting of closures on profiled sheet seams, with big setting head 16 mm 4.8 x 17 mm Cup blind rivet for riveting of fixed points, with flat round head 9.5 mm 4.8 x 12.5 mm Accessories for installation and tools Description Usage Tool for folding up / folding down of profiled sheets combined for ridge and eaves side steel galvanized and lacquered Spreader beam for lifting steel galvanized and lacquered Cutting tool for angular cuttings Wedge for opening profiled sheets plastic Fall arrest system personal safety system single anchor point Description Finish Single anchor point single anchor point, perforation free assembly Safety harness personal safety equipment, movable guide 10 m rope Storage cupboard steel sheet, dimension 600 x 400 x 250 mm Available as cable system with intermediate brackets that are continuously movable (slight change of direction on corners); on request 12

13 FLASHINGS / ACCESSORIES Coil material standard width 667 mm and 1250 mm (other coil widths on request) maximum coil length 30 m Weight (kg/m 2 ) alu-zinc alloy galvanized and colour-coated, top side 25 µm polyester coated, rear side protective coating galvanized and colour-coated, top side 25 µm PVDF coating, rear side protective coating mill finish or mill finish and stucco-embossed colour-coated, top side 25 µm polyester coated, rear side protective coat mill finish EN 988 (EN 988 pre-weathered also available) mill finish EN Flashings Finish Flashings max. length 6.00 m (production according to drawings) Hat-profiles Z-profiles e. g. steel 1.6 mm cut 50/120/75/120/50 mm, heigth 120 mm e. g. steel 1.6 mm cut 65/120/65 mm, heigth 120 mm price for coil material plus necessary cutting and costs for cutting Calculation costs for each edge (1 bend count as 2 edges) Flashings less than 1000 mm length will be priced per meter. Bezels (connector system) construction height 300 mm for dome lights etc. cover caps, handmade, for closing off profiled sheet seams for welding/sealing for welding/sealing 1.00 x 1.00 m x 1.00 m aluminium mill finish 1.20 x 1.20 m aluminium 1.20 x 1.20 m x 1.50 m colour-coated 1.50 x 1.50 m Cover cap / Cover cap / Please indicate roof pitch when ordering bezels (connector system). Not available thermally insulated. Soaker construction height 300 mm, thermal-insulated for welding with flat flange for sealing R-MER LOC Dome light, double-layer aluminium mill finish aluminium colour-coated 1.00 x 1.00 m x 1.20 m x 1.50 m x 1.00 m Electric opener, 230 V, 1.20 x 1.20 m mm stroke, incl. button 1.50 x 1.50 m Internal soaker linings are made out of aluminium mill finish. Other sizes and extra for fall protection system on request. R-MER metal roofing systems 13

14 R-MER Metal roofing systems Bituminous Membrane Roofing Systems Cold Liquid Roofing Systems Roof Asset Management Programme (RAMP ) GET IN TOUCH The Garland Company UK Limited Glevum Works Upton Street Gloucester GL1 4LA United Kingdom Phone +44 (0) Fax +44 (0) info@garlandukltd.co.uk The Garland Company UK Limited R-MER is a registered trademark of The Garland Company, Inc. 02/2017