Lagan Tile. Lagan Tile PO Box 176 Sheepwalk Road Lisburn Co. Antrim BT28 3NS

Transcription

1 Lagan Tile Lagan Tile PO Box 176 Sheepwalk Road Lisburn Co. Antrim BT28 3NS Tel: Fax:

2 Lagan Tile Lagan Tile is a trading division of Lagan Cement Products Ltd. and is part of Lagan Cement Group which has a combined annual turnover in excess of 150m Lagan Tile manufacture concrete roof tiles and ridge tiles in a range of profiles and colours. We also offer an extensive collection of accessories that compliment our range including dry ridge, dry verge, ventilation systems and underlays. 2 We aspire to be the best at what we do. VISION STATEMENT

3 FLAT TILE A traditional concrete interlocking flat tile which is fixed on the roof in a broken bond pattern. 1 RED 2 GREY 3 BLACK 4 BROWN 5 ANTIQUE BROWN 6 ANTIQUE RED DOUBLE ROLL TILE A concrete interlocking tile in the timeless double roman profile. 1 RED 2 GREY 3 BLACK 4 BROWN 5 ANTIQUE BROWN 6 ANTIQUE RED ELITE TILE A smooth concrete interlocking slate tile with the latest thin leading edge design. 1 GREY 2 BLACK SQUARE TOP TILE A classic low profile tile that is proving increasingly popular on newbuild and refurbishment alike. 1 GREY 2 BROWN 3 ANTIQUE RED 3 RED IMPORTANT NOTICE: Where the wind load calculated in accordance with B.S. 5534:2003 provides an uplift force which exceeds the dead load of the tile, mechanical fixings in addition to the minimum fixings will be necessary. Factors which must be considered: 1) Exposure and location of the site 2) Roof pitch 3) Height of the roof 4) Wind speed The roof tile dimensions given are nominal sizes, however all Lagan Tiles are manufactured within the dimensional tolerances permitted under B.S.EN

4 Technical Information FLAT TILE DESIGNATION: T-EN 490-IL-0-RF-297-/-/ Size of Tile (overall) Minimum Pitch Maximum Pitch Headlap (minimum) Headlap (maximum) Gauge (maximum) Covering Width of one tile (nominal) Covering Capacity (Headlap 75 mm) Covering Capacity (Headlap 100 mm) Hanging Length (nominal) Weight per 1000 (approx.) Recommended Batten size (see BS5534) Rafter centres up to 600mm Recommended Nail size Maximum Pitch Profile Depth (nominal) DOUBLE ROLL TILE DESIGNATION: T-EN 490-IL-22.5-RF-301-/-/ Size of Tile (overall) Minimum Pitch Headlap (minimum) Headlap (maximum) Gauge (maximum) Covering Width of one tile (nominal) Covering Capacity (Headlap 75 mm) Covering Capacity (Headlap 100 mm) Hanging Length (nominal) Weight per 1000 (approx.) Recommended Batten size (see BS5534) Rafter centres up to 600mm Recommended Nail size Profile Depth (nominal) ELITE TILE DESIGNATION: T-EN 490-IL-0-RF-297-/-/ Size of Tile (overall) Minimum Pitch Maximum Pitch Headlap (minimum) Headlap (maximum) Gauge (maximum) Covering Width of one tile (nominal) Covering Capacity (Headlap 75 mm) Covering Capacity (Headlap 100 mm) Hanging Length (nominal) Weight per 1000 (approx.) Recommended Batten size (see BS5534) Rafter centres up to 600mm Recommended Nail size Profile Depth (nominal) LAGAN SQUARE TOP TILE DESIGNATION: T-EN 490-IL-18.5-RF-300-/-/ X 330mm 17 1/2 º (for rafter length over 8 metre, please consult our technical department) 90º (subject to fixing specification) 75mm above 25º // at 25º or below 345mm 297mm 9.8 tiles / m tiles / m2 400mm 5.4 tonnes 50x25mm 50mm x 3.35mm 90º (subject to fixing specification) 0mm 420 x 330mm 22 1/2º Maximum Pitch 90º (subject to fixing specification) 75mm above 25º // at 25º or below 345mm 300mm 9.7/m2 10.4/m2 400mm 4.9 tonnes 50x25mm 60mm x 3.35mm 22.5mm 420 x 330mm 22 1/2º (for rafter length over 8 metre, please consult our technical department) 90º (subject to fixing specification) 75mm above 25º // at 25º or below 345mm 297mm 9.8/m2 10.5/m2 400mm 5.0 tonnes 50x25mm 45mm x 3.35mm 0 mm Size of Tile (overall) 420 x 330mm Minimum Pitch 22 1/2 º Maximum Pitch 90º (subject to fixing specification) Headlap (minimum) 75mm above 25º // at 25º or above Headlap (maximum) Gauge (maximum) 345mm Covering Width of one tile (nominal) 297mm Covering Capacity (Headlap 75 mm) 9.8/m2 Covering Capacity (Headlap 100 mm) 10.4/m2 Hanging Length (nominal) 400mm Weight per 1000 (approx.) 5.0 tonnes Recommended Batten size (see BS5534) Rafter centres up to 600mm 50x25mm Recommended Nail size 55mm x 3.35mm Profile Depth (nominal) 18.5 mm 4

5 Ridge Tiles A range of ridge tiles and finials designed and created by Lagan tile craftsmen to enhance the appearance of your home. All Ridge Products are available in Red, Dark Brown, Black, and Slate Grey. All handmade ornamental ridge tiles and finials are manufactured from glass fibre reinforced concrete. ELITE RIDGE UNIVERSAL ANGLE RIDGE UNIVERSAL ANGLE HIP UNIVERSAL ANGLE VENT RIDGE HALF ROUND RIDGE THIRD ROUND HIP BABY UNIVERSAL ANGLE Length 300mm BABY HALF ROUND Length 300mm MONO RIDGE Length 450mm SHORT BLOCK END LONG BLOCK END UNIVERSAL ANGLE HIP BLOCK END Also available to suit THIRD ROUND and ELITE 5

6 Ridge Tiles SCROLL FINIAL Available with Roll-Top, Universal Angle, Half Round and all ornamentals. FLEUR-DE-LYS FINIAL Available with Roll-Top, Universal Angle, Half Round and all ornamentals. BALL FINIAL Available with Roll-Top, Universal Angle, Half Round and all ornamentals. ROLL TOP RIDGE Roll Top Ridge available in angles of 90,105,120 and 130 degrees CLUB CRESTED ORNAMENTAL FLEUR-DE-LYS ORNAMENTAL VICTORIA ORNAMENTAL CROWN ORNAMENTAL ALL RIDGE PRODUCTS ARE AVAILABLE IN RED, DARK BROWN, BLACK, AND SLATE GREY. ALL HANDMADE ORNAMENTAL RIDGE TILES AND FINIALS ARE MANUFACTURED FROM GLASS FIBRE REINFORCED CONCRETE. 6

7 Calculation tables Vertical Coverage SLOPE AT END LAPS OF: Horizontal lengths are based on a setting out gauge for three standard tiles, although the tolerance fit of the interlock will permit a small amount of play, this should not be relied on to accomodate inaccuracies in setting out the roof. All figures are Nett. Wastage is to be added. COURSES UP ROOF SLOPE 75mm m 0.420m m 0.740m m 1.060m m 1.380m m 1.700m m 2.020m m 2.340m m 2.660m m 2.980m m 3.300m m 3.620m m 3.940m m 4.260m m 4.580m m 4.900m COURSES UP ROOF SLOPE 75mm m 5.220m m 5.540m m 5.860m m 6.180m m 6.500m m 6.820m m 7.140m m 7.460m m 7.780m m 8.100m m 8.420m m 8.740m m 9.060m m 9.380m m 9.700m Horizontal Coverage FLAT TILES & ELITE TILES DOUBLE ROLL TILES SQUARE TOP TILES TILES IN COURSE TILES IN COURSE TILES IN COURSE

8 Concrete Roof Tile INFORMATION SHEET The industry quality standard for Concrete Roof Tiles is BS EN 490 and all concrete roof tiles produced by Lagan Tile are manufactured in accordance with this. Lagan Tile also operates an Integrated Management System, incorporating ISO9001, ISO14001 and ISO18001, all of which have third party accreditation Lagan concrete tiles are manufactured by high-pressure extrusion and compaction of a mix of aggregate, cement, pigment and water and after initial curing are painted with an acrylic coating. Whilst every effort is made to produce a consistent product in every aspect due to the nature of the product, and as a consequence of the manufacturing & handling processes the following surface characteristics may occur. It is fully recognised both within the industry and BS EN 490 that these will not affect the performance of the tiles SCRATCHES & ABRASIONS: These can be caused by packing, loading, transport and handling on site: These are surface marks that will not affect the overall quality of the tile and will become less apparent with natural weathering, see Annex A, BS EN 490 EFFLORESCENCE: This is a surface phenomenon associated with natural concrete products and influenced by weather conditions. The hydrated lime (calcium hydroxide) in the cement reacts with carbon dioxide in the atmosphere to produce insoluble calcium carbonate, which is deposited as efflorescence. The chemical process of carbonation continues and will eventually form soluble calcium bicarbonate. Normal weathering will wash the bicarbonate away. The degree of efflorescence is relative to lime content and local weather conditions SURFACE COATING: In common with most manufacturers Lagan roof tiles are surface treated with an acrylic coating. The major benefit being to protect the tile during the early, critical stages of its lifespan. It is recognised in the roofing industry that the surface coating of a concrete tile is temporary, lasting only for a few years; long enough to give that protection to the early life of the product. The performance of the roof tile is not affected by any of the above conditions and the quality requirements of the tile remain intact, see Annex A, BS EN 490 MOSSES & LICHENS: Mosses and lichen tend to grow on roofs located in the vicinity of trees, or in shady damp conditions. North facing slopes remain damper longer and attract moss and lichen growth more so than roof slopes which dry out quicker. Neither the material content nor the production process cause lichen growth or moss formation. 8