Construction Details 5-37

Transcription

1 5-37

2 5-38 Construction Details

3 5-39

4 5-40 Construction Details

5 5-41

6 5-42 Construction Details

7 5-43

8 5-44 Construction Details

9 5-45

10 5-46 Construction Details

11 5-47

12 5-48 Construction Details

13 5-49

14 RING ANCHOR DETAIL BOND BEAM FILLED WITH 3000 psi CONCRETE 8" LAP #4 REINF. BAR 8" LAP A 2 PANEL SPAN CONTEC AAC SLAB PANEL #4 REINF. BAR CONTEC AAC BLOCK WALL 2 #4 CONTINUOUS AT RING ANCHOR ACCORDING DESIGN MIN. 3" A 1 PLAN VIEW >1/2" #3 BAR AT GROUT KEY ACCORDING TO DESIGN MIN. 3" 2#4 BARS CONTINUOUS JOINT RE-BAR SECTION "A2" MINIMUM BEARING SECTION "A1" FLOOR

15 CANTILIVER DETAIL L = LENGTH OF PANEL CANTILIVER SLAB PANEL CANTILIVER LENGTH < 5'-0" OR L/3 GROOVED FILLED WITH MORTAR TYPE M REINFORCED WITH BAR #3 AT PANEL JOINT AAC U-BLOCK BOND BEAM REINFORCED WITH 2 #5 CONTEC BLOCK WALL Construction Details FLOOR

16 5-52 RING ANCHOR DETAIL 3" MINIMUM BEARING 8" LAP 8" LAP 2 #4 BARS CONTINUOUS AT RING ANCHOR PANEL SPAN AAC BLOCK WALL BELOW PANEL SPAN FLOOR PANEL EDGE #4 BARS AT RING ANCHOR 3" MINIMUM BEARING Construction Details PLAN VIEW FLOOR-04

17 DETAIL "D" PANEL SPAN MINIMUM BEARING 2 #4 BARS BOND BEAM #3 BAR GROUT KEY RECES STEEL SUPPORT BRACKET INTO SUPPORTED PANEL AND ALONG SUPPORTING PANEL EDGES Construction Details INTERIOR AAC BLOCK WALL FLOOR

18 5-54 Construction Details

19 MESH DETAIL AROUND WINDOWS FIRST LAYER 1/4" SECOND LAYER CONTEC AAC BLOCK WALL FIBER GLASS MESH SECTION COAT THICKNESS MINIMUM 12" CONTEC AAC LINTEL OR CONCRETE BEAM (SEE DETAIL) 6" HEIGHT OF BEAM OR AAC LINTEL 4" 6" 8" VENTANA Y/O PUERTA 8" 20" CONTEC AAC BLOCK WALL 8" 8" SYMBOLS: FIBER GLASS MESH (EMBEDDED IN COAT THICKNESS) MAS

20 5-56 FIXING STEEL FRAME DETAIL DOOR ON CONTEC AAC WALLS L CONTEC LINTEL/U-BLOCK/CONCRETE BEAM C DO NOT EXTEND FRAME BELOW LINTEL SUPPORT CONTEC GALVANIZED TOX ALL PURPOSE ANCHORS HOLE 1/4" PULG 1" 3/4" 1 3/16" STEEL FRAME FOR DOOR STEEL PLATE WITH HOLES FOR CONTEC NAILS Construction Details INSERT INTO FOUNDATION SLAB MAS-44

21 CONTEC WALL AT HOLLOW CORE FLOOR BRICK TIE AT 24" HORIZONTAL AND 16" VERTICAL AIR SPACE CONTEC AAC BLOCK WALL 2 #4 BARS AT RING BEAM HOLLOW CORE CONCRETE FLOOR PANEL Construction Details BRICK VENEER CONTEC AAC BLOCK WALL MAS

22 5-58 CONTEC WALL/CONTEC FLOOR SLAB TYPICAL DETAIL EXTERIOR FINISH (MIN. 1/4" THICKNESS) MIN 3" CONTEC AAC BLOCK WALL 3000 psi CONCRETE REINFORCED WITH 2 #4 BARS MORTAR LEVELING BED (TYPE M) CONTEC AAC BLOCK WALL BAR JOINT CONTEC AAC FLOOR PANEL Construction Details MAS-05

23 WOODEN JOIST AND CONTEC AAC BLOCK WALLS EXTERIOR FINISH (MIN. 1/4" THICKNESS) CONTEC AAC U-BLOCK BOND BEAM FILLED WITH 3000 psi CONCRETE 2 #5 CLIP #2 AT 8" CONTEC AAC BLOCK WALL 1/2" THREADED ANCHOR, WITH WASHER & NUT (SPACING PER STRUCTURAL DESIGN) FLOOR DECKING AS SPECIFIED WOOD PLATE GYPSUM BOARD HANGER AT EACH JOIST INTERIOR FINISH (MIN. 1/4" THICKNESS) MAS

24 SECTION OF FLOOR ABOVE EXTERIOR OPENING CONTEC AAC BLOCK WALL MORTAR LEVELING BED (TYPE M) 3/4" #3 BENT BAR AT GROUT KEY FILLED WITH MORTAR TYPE M BOND BEAM CONTEC AAC U-BLOCK BEARING LENGHT MINIMUM 3" CONTEC AAC FLOOR PANEL CONTEC AAC LINTEL 3000 psi CONCRETE REINFORCED WITH 2 #4 BARS AT RING BEAM TOP OF OPENING MAS

25 SECTION OF FLOOR ABOVE INTERIOR OPENING BEARING LENGTH (MINIMUM 3") CONTEC AAC LINTEL OR CONCRETE BEAM USE BENT BARS WHERE FLOOR PANELS ARE NOT ALIGN BEARING LENGHT (MINIMUM 3" ) AAC U-BLOCK BOND BEAM CONTEC AAC FLOOR PANEL 2 #4CONTINUOUS BOND BEAM FILLED WITH MORTAR TYPE M MAS-08 2 #4 CONTINUOUS BON BEAM WITH 300 psi CONCRETE AAC U-BLOCK BOND BEAM # 3 CONTINUOUS BAR AT PANEL GROUT KEY FILL WITH MORTAR TYPE M #3 BAR AT PANEL GROUT KEY FILL WITH MORTAR TYPE M CONTEC AAC FLOOR PANEL BEARING LENGTH (MINIMUM 3") USE BENT BARS WHERE FLOOR PANELS ARE NOT ALIGN BEARING LENGHT (MINIMUM 3" ) AAC U-BLOCK BOND BEAM CONTEC AAC FLOOR PANEL 2 #4CONTINUOUS BOND BEAM FILLED WITH MORTAR TYPE M MAS-08 2 #4 CONTINUOUS BON BEAM WITH 300 psi CONCRETE AAC U-BLOCK BOND BEAM # 3 CONTINUOUS BAR AT PANEL GROUT KEY FILL WITH MORTAR TYPE M #3 BAR AT PANEL GROUT KEY FILL WITH MORTAR TYPE M CONTEC AAC FLOOR PANEL Construction Details CONTEC AAC LINTEL OR CONCRETE BEAM TOP/OPENING TOP/OPENING 5-61 MASO 8

26 NON ALIGNED GROUT KEY FLOOR PANELS AT RING BEAM A PLAN USE BENT BARS WHERE PANELS ARE NOT ALIGN 2 #4 BARS CONT AT BOND BEAM W/3000 CONCRETE #3 BAR AT PANEL GROUT KEY FILL WITH MORTAR TYPE M TOP OF PANEL MIN. BEARING LENGTH 3" CONTEC AAC FLOOR PANEL CONTEC AAC BEARING BLOCK WALL BOND BEAM AAC CONTEC U-BLOCK A SECTION MAS

27 FACADE MOLDINGS CONTEC WALL PANEL ANGLE BEAM COMPRESSIBLE MATERIAL CONNECTOR (ACC-PM-013) CONTEC WALL PANEL METAL STRIP COMPRESSIBLE MATERIAL 3 CONTEC NAILS CONNECTION DETAIL W/S CATALOG NUMBER: MOLD-103 DESCRIPTION: d = 5", 7" AND 6" LARGE 2'-1/2" NOTE: IT IS RECOMENDED TO USE AT LEAST PAINTING FINISHING OR STUCCO d 12" R=d d PERSPECTIVE W/S 1'-3 3/4" PLAN VIEW W/S 5-63

28 FACADE MOLDINGS BEAM COMPRESSIBLE MATERIAL CONNECTOR (ACC-PM-013) CONTEC WALL PANEL 3 CONTEC NAILS METAL STRIP CONNECTION DETAIL W/S CATALOG NUMBER: MOLD-104 DESCRIPTION: d = 5", 6",7" OR 8" HEIGHT 2'-1/2" NOTE: IT IS RECOMENDED TO USE AT LEAST PAINTING FINISHES OR STUCCO d PERSPECTIVE W/S 1'-1 3/4" PLAN VIEW W/S 5-64

29 d Construction Details FACADE MOLDINGS METAL STRIP CONNECTOR (ACC-PM-013) CONTEC WALL PANEL CONTEC WALL PANEL BEAM CONNECTION DETAIL W/S CATALOG NUMBER: MOLD-105 DESCRIPTION: d = 6", 7", 8", 9" OR 12" LARGE 2'-1/2" THICKNESS 1'-1 3/4" NOTE: IT IS RECOMENDED TO USE AT LEAST PAINTING FINISHES OR STUCCO 1" 1" 1'-1 3/4" PLAN VIEW W/S PERSPECTIVE W/S REV2/10/6 5-65

30 5-66 FACADE MOLDINGS 1" 1" METAL STRIP CONTEC WALL PANEL BEAM 1'-3 3/4" PLAN VIEW W/S CONNECTOR (ACC-PM-013) 3 CONTEC NAILS d CATALOG NUMBER: DESCRIPTION: d = 5" - 12" HEIGHT 2'-1/2" LENGTH 1'-3 3/4" MOLD-106 NOTE: IT IS RECOMENDED TP USE AT LEAST PAINTING FINISHING OR STUCCO Construction Details CONNECTION DETAIL W/S PERSPECTIVE W/S

31 FACADE MOLDINGS METAL STRIP CONNECTOR (ACC-PM-013) CONTEC WALL PANEL BEAM 3 CONTEC NAILS CATALOG NUMBER: DESCRIPTION: DIAM: 1'-3 3/4" HEIGHT 2'-1/2" MOLD-101B CONNECTION DETAIL W/S NOTE: IT IS RECOMENDED TO USE AT LEAST PAINTING FINISHES OR STUCCO 8" 1'-3 3/4" PLAN VIEW W/S PERSPECTIVE W/S 5-67

32 FACADE MOLDINGS CONNECTOR SHEET CONNECTOR (ACC-PM-013) CATALOG NUMBER: MOLD-108 CONTEC WALL PANEL 3 CONTEC NAILS DESCRIPTION: d = 5", 6" Y 7" HEIGHT 2'-1/2" WIDTH 1'-3 3/4" AND 2' BEAM CONNECTION DETAIL W/S NOTE: IT IS RECOMENDED TO USE AT LEAST PAINTING FINISHES OR STUCCO d '-3 3/4"-2" PLAN VIEW W/S PERSPECTIVE W/S 5-68

33 FACADE MOLDINGS METAL STRIP CONNECTOR (ACC-PM-013) CONTEC WALL PANEL 3 CONTEC NAILS CATALOG NUMBER: MOLD-109 DESCRIPTION: d = 5", 6" AND 7" HEIGHT 2'-1/2" LENGTH 1'-3 3/4" BEAM CONNECTION DETAIL W/S NOTE: IT IS RECOMENDED TP USE AT LEAST PAINTING FINISHING OR STUCCO d 14 1'-3 3/4" PLAN VIEW W/S PERSPECTIVE W/S 5-69

34 WALL PANEL CATALOG NUMBER: MOLD-201 NAME: TRAPECIO THCK. 7" 8" 10" HEIGHT (IN) 1'-4 3/4",1'-7", 2'-1/2" 1'-4 3/4",1'-7", 2'-1/2" 1'-4 3/4",1'-7", 2'-1/2" LENGTH (IN) 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" PANEL WITH OR WITHOUT OFA 1" 3" 2" " 2" DESIGN THICKNESS 2'-1/2" SECTION PERSPECTIVE 5-70

35 WALL PANEL CATALOG NUMBER: MOLD-202 NAME: TRAPECIO THCK. HEIGHT (IN) 6" 1'-4 3/4",1'-7", 2'-1/2" 7" 1'-4 3/4",1'-7", 2'-1/2" 8" 1'-4 3/4",1'-7", 2'-1/2" 10" 1'-4 3/4",1'-7", 2'-1/2" PANEL WITH OR WITHOUT OFA LENGTH (IN) 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 1 1/16" DESIGN THICKNESS 1 1/16" 2" 1-5/16" /16" 2'-1/2" SECTION PERSPECTIVE 5-71

36 WALL PANEL CATALOG NUMBER: MOLD-203 NAME: TRAPECIO THCK. 7" 8" 10" HEIGHT (IN) 1'-4 3/4",1'-7", 2'-1/2" 1'-4 3/4",1'-7", 2'-1/2" 1'-4 3/4",1'-7", 2'-1/2" LENGTH (IN) 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" PANEL WITH OR WITHOUT OFA 3" 1" 2" 1" DESIGN THICKNESS 2" 2'-1/2" SECTION PERSPECTIVE 5-72

37 WALL PANEL CATALOG NUMBER: MOLD-205 NAME: TRAPECIO THCK. HEIGHT (IN) 6" 1'-4 3/4",1'-7", 2'-1/2" 7" 1'-4 3/4",1'-7", 2'-1/2" 8" 1'-4 3/4",1'-7", 2'-1/2" 10" 1'-4 3/4",1'-7", 2'-1/2" PANEL WITH OR WITHOUT OFA LENGTH (IN) 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 6'-6 3/4" TO 19'-8 1/4" 1 1/16" 1 1/16" 2" 1-5/16" 1-1/16" 2'-1/2" SECTION PERSPECTIVE 5-73

38 5-74 Construction Details

39 5-75

40 5-76 Construction Details

41 5-77

42 5-78 Construction Details