Gas Fireplaces. B41XTE-10 Gas Fireplace. Framing Dimensions: Unit Dimensions: Non-Combustible 1012mm Requirements: V Opening for gas connection

Transcription

1

2 1XTE-1 Gas Fireplace Model 1XTE-NG1 1XTE-LP1 Fuel Type Natural Gas Propane Gas Minimum Supply Pressure Manifold Pressure - High Manifold Pressure - Low 5 W.C. (1.5 kpa) 3.5 W.C. (.7 kpa) 1. W.C. (. kpa) 11 W.C. (.7 kpa) 1 W.C. (.9 kpa). W.C. (1. kpa) Orifice Size #3 DMS #9 DMS Minimum Input ltitude -5 ft. (-137m) 3, TU/h (.79 kw) 9,5 TU/h (.5kW) Maximum Input ltitude -5 ft. (-137m) pproved Venting Systems Flex Vent Systems: Rigid Pipe Vent Systems: Unit Dimensions: 3/",5 TU/h (1.5 kw) 37,5 TU/h (1.99 kw) Vent Sizing 5 Inner / Outer 5 Inner / Outer 5mm 19-1/" 95mm -9/1" 113mm 1-11/1" 159mm 3-3/" 97mm FPI strocap Flex Vent Simpson Direct Vent Pro Selkirk Direct-Temp Metal-Fab Sure Seal ICC Excel Direct 13-3/1" 335mm Framing Dimensions: Framing Dimensions Description 1XTE-1 M Framing Width 7-1/"(1mm) N Framing Height 9-1/" (157mm) O (Rear Vent) Framing Depth - Rear Vent 3-1/" (591mm) O (Top Vent) Framing Depth - Top Vent -5/" (575mm) P Corner Facing Wall Width -1/" (153mm) Q Corner Facing Wall Width 5-3/1" (13mm) R (Rear Vent) Framed Chase Ceiling - Rear 9-1/" (157mm) R (Top Vent) Framed Chase Ceiling - Top 5-1/" (13mm) S (Rear Vent) Vent Centerline Height - Rear -1/" (7mm) S (Top Vent) Vent Centerline Height - Top 7-1/" (17mm) Rigid / Flex T Gas Connection Height 1-1/" (3mm) U Gas Connection Inset 5" (17mm) V Gas Connection Width 3-1/" (mm) W Non-Combustible Top Height 13-1/" (33mm) 3-7/1" 113mm 35" [ 9mm] WINDOW -7/1" 1mm 1-15/1" 9mm ** Important: Framing height requires consideration of the hearth depth. Dimension N = N + the thickness of the installed hearth. R 37-11/1" 95mm 3-7/" mm 39-7/" Non-Combustible 11mm Requirements: 1-1/1" SCREEN FRME 7mm 5-1/" (17mm) SCREEN FRME -3/" (13mm) 1-3/" (1mm) 3-3/" (933mm) " 1mm WINDOW Header (steel stud) on edge Min. 13-1/" (33mm) 3-3/" 9mm Non-Combustible Header (steel stud) on edge N M P Drywall, Wood (or other facing) W O T Non-Combustible Header (steel stud) on edge Rear Vent Non-Combustible Facing 11" (79mm) dia. Hole through wall Vent. S Top Vent S 7-1/" (1mm) Framing Min. 3-1/ (9mm) Min. 3-1/ (9mm) Q U V Opening for gas connection

3 Clearance Requirements: 1XTE Gas Fireplace E D F C lcove F Clearance: Dimension Measured From: : Mantel Height (min.) 15" (31mm) Top of Fireplace Opening : Sidewall 9" (9mm) Side of Fireplace Opening C: Ceiling 33-3/" (933mm) Top of Fireplace Opening D: Mantel Depth (max.) 1" (3mm) 3-1/ (591mm) from Top of Fireplace Opening E E: lcove Width " (15mm) Wall to Wall (Minimum) F: lcove Depth 3" (91mm) Front to ack Wall (Maximum) Notes: " No Hearth Required Minimum Vent Clearances to Combustibles Horizontal Top Horizontal Side Horizontal ottom Vertical Vent 3" (7mm) " (51mm) " (51mm) " (51mm) NOTE: 1" deep non-combustible hearth pad is recommended for hardwood flooring and carpet. Mantel Clearances: Combustible Mantels: Due to the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram on the right. Note: Ensure the paint that is used on the mantel and the facing is heat resistant or the paint may discolour. Mantel Leg Clearances: 9 Side Wall (Measured from side of Fireplace Opening) Mantel leg 1-1/" Mantel leg 7 llowable mantel leg projection. 3" Mantel Clearances 1XT From Top of Fireplace Opening C D 35-1/" (95mm) 3-1/" (591mm) 19-1/" (95mm) 15" (31mm)

4 IMPORTNT FINISHING DETIL NOTE: FINISHING efore placing unit into final position - it is important to know the total thickness / height of finished hearth (tile, carpet, etc.) The base of the fireplace should be level or higher than the finished hearth height. Diagram 1 Note: ll non-combustible facing material should butt up cleanly to the flanges around the firebox opening. Rough edges will be visible from the front view with the flush louvers or flush panels - if not using the optional finishing trim. To maintain a clean finished edge - it is recommended to install the noncombustible facing material with the finished edge against the fireplace / nailing strips. lternatively, you can use J Style Trim or Metal Corner ead to cover cut edges of the non-combustible facing material. J-style Trim or metal corner bead may be used to finish these edges Diagram 3 3 " 37 5 " Diagram 3: Shown with optional Finishing Trim

5 1XTE Gas Fireplace Horizontal Terminations: STROCP XL & RIGID RER VENT KIT FOR CORNER INSTLLTIONS Designed for a minimum vent configuration when using a rear vent application with a horizontal termination in a corner installation. Kit# 9-1 Includes: 1 strocap XL 9-3/P 1 Rigid Pipe daptor Standoff (Optional) DV-WT Placement of the Unit into the Corner ack Top Corner of Unit to Wall 3" Inside Corner out along the Wall -1/" cross the Face of the Unit, Wall to Wall 5-3/1" - Clearance to Outside Corner 13" - Clearance to Inside Corner 5-1/" 1 " Galvanized Rigid Pipe 5DV- 1-1/" Galvanized Pipe Extension 5DV- 1 5º Galvanized Elbow 5DV-E5 1 9ml MillPac 9-1 Standoff (Optional) 3-1/ strocap XL 5 elbow Rigid Pipe daptor 5-3/1 IMPORTNT Must use Rear Venting Deflector packaged with unit in rear vent horizontal termination applications. asic Horizontal & Vertical Terminations: Rigid Pipe Vent Systems offer a complete line of component parts for installation of both horizontal and vertical installations. Many items are offered in decorative black, as well as galvanized finish. Vertical Terminal Storm Collar The minimum components required for a basic Horizontal Termination are: 1 strocap XL Termination Cap 1 9 o Elbow 1 Rigid Pipe daptor 1 1 Length of rigid pipe to suit wall thickness The minimum components required for a basic Vertical Termination are: 1 Vertical Termination Cap 1 Rigid Pipe daptor 1 Lengths of pipe to adequately penetrate roof 1 Ceiling Firestop 1 Flashing 1 Storm Collar Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap. For siding other than vinyl, furring strips may be used, instead of a vinyl siding standoff, to create a level surface to mount the vent terminal. The Terminal must not be recessed into siding. Measure the wall thickness including furring strips. Flashing Ceiling Firestop Pipe Length o 9 Elbow Rigid Pipe daptor (77-99) Standoff (Optional) Vent Guard -if required* (Part #9-5/P) strocap XL Termination Cap (Part #9-3/P) (Mandatory in all Horizontal Terminations) If a Standoff is required (it must be used with vinyl siding), measure to outside surface of wall without siding and add inches.

6 Gas Fireplaces 1XTE Gas Fireplace Venting rrangements for Horizontal Terminations: The diagrams show all allowable combinations of vent runs with 5" x " venting using the Regency direct vent system or rigid vent system. vent guard should be used whenever the termination is lower than the specified minimum or as per local codes. For horizontal terminations the Regency Direct Vent Flex System may be used for installations upto a maximum continuous vent length of 1ft (3.m). Note: Must use optional rigid pipe adaptor (Part # when using Rigid Pipe vent systems. Maintain clearance to combustibles. Horizontal vent must be supported every 3 feet. Firestops are required at each floor level and whenever passing through a wall. 1 1 Max. 3 (.9m) Rigid or Flex 7-1/" (1.m) Max. 3"(.9m) - 1/"(.7m) Vent Restrictor - Set 1 Factory Setting - No Restrictor Required Horizontal Terminations - Rigid Pipe 5 x : Top Vent - No Vertical Rise When venting with a 9 elbow directly off the unit Flex vent or approved Rigid Vent System Max. 3 ft. horizontal run Rear Vent w/ Horizontal Termination Max. 3ft. horizontal run IMPORTNT Must use Rear Venting Deflector packaged with unit in rear vent horizontal termination applications. Standoff (Optional) Standoff (Optional) Horizontal Termination Cap Horizontal Termination Cap Rigid Pipe daptor o 9 Elbow Rigid Pipe daptor IMPORTNT Must use Rear Venting Deflector packaged with unit in rear vent horizontal termination applications.

7 1XTE Gas Fireplace VENTING RRNGEMENTS FOR HORIZONTL TERMINTIONS FOR VERTICL TERMINTIONS The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 9 o (two 5 o elbows equal one 9 o elbow). Maintain clearances to combustibles as listed in "Clearances" section Horizontal vent must be supported every 3 feet. Firestops are required at each floor level and whenever passing through a wall. wall thimble is mandatory for all horizontal terminations due to high temperatures The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using two 9 o elbows, with Rigid Pipe Venting Systems for Propane and Natural Gas. Two 5 o elbows equal to one 9 o elbow. Maximum of four 5 o elbows allowed. Vent must be supported at offsets. Firestops are required at each floor level and whenever passing through a wall. Maintain clearances to combustibles as listed in the "Clearances" section. Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting to 3-1/" opening, -1/"opening and to 1-1/" opening Restrictor 1-1/ Open Set Restrictor -1/ Open Set Restrictor 3-1/ Open Set Restrictor 1-1/ Open Set 3 7-1/" (17mm) Minimum Height Requirement 1 Restrictor -1/ Open Set Restrictor 3-1/ Open Set 1 Maximum 1 Centerline to Centerline Min. 7-1/ (1.m) Minimum (.m) Maximum Centerline to Centerline