1 of 3 3/29/2016 4:07 PM

Transcription

1 Convertible Top Adjustments: Folding Top Storage Compartment Closeo... 1 of 3 3/29/2016 4:07 PM FOLDING TOP STORAGE COMPARTMENT CLOSEOUT PANEL ADJUSTMENT - FRONT IMPORTANT: - Due to the tight clearance of the storage compartment front closeout panel to the upper rear end trim finish panel and the rear roof panel headliner, slowly cycle the folding top a few seconds at a time to ensure panels are moving properly and not hanging up or interfering with the folding top. - Inspect the closeout panels with the folding top in the down position. Align the closeout panels so there is an even gap to the upper trim finish panel and to each other. Also ensure there is a consistent closeout of the panel seals to the rear compartment lid. Fore/Aft Adjustment Procedure IMPORTANT: The folding top will only remain in partial open or closed position for 3 minutes before the hydraulic pressure is released and the top will descend. For adjustments exceeding this time limit, place the folding top in the service position. Refer to Folding Top Retaining Strap Installation Position. 2. Loosen the front storage compartment closeout panel hinge bolts (1) and adjust the closeout panel as necessary. Refer to Folding Top Stowage Compartment Closeout Panel Hinge Replacement - Front. 3. Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panel. 4. If further adjustment than the hinge will allow is necessary, loosen the folding top stowage compartment closeout panel link fasteners and adjust as necessary. Refer to Folding Top Stowage Compartment Closeout Panel Link Replacement. Height Adjustment Procedure 1. IMPORTANT: The front compartment closeout panel will, by design, be in a higher position than the two outer closeout panels when the rear compartment lid is open in the rearward position. They will be brought down to a uniform height by the forward edge of the rear compartment lid once the opening top cycle is completed. Start opening the folding top, stop when the roof panels are stowed in the rear compartment and the rear compartment lid is still fully open rearward, 2. Remove the right and left lock pillar upper garnish molding.

2 Convertible Top Adjustments: Folding Top Storage Compartment Closeo... 2 of 3 3/29/2016 4:07 PM 3. Loosen the bolts (1) on both sides of the stowage compartment closeout panel link drive rod assembly. 4. IMPORTANT: The front closeout panel may settle to a lower height once the bolts are tightened. It may be necessary to start at a higher dimension and adjust to accommodate for settling Manually position the underside of the front closeout panel (a) to mm ( in) from the outer surface of the stowed roof panel, tighten the bolts. 5. Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panels. 6. Install the right and left lock pillar upper garnish molding. 7. Inspect the folding top for proper operation.

3 Convertible Top Adjustments: Folding Top Storage Compartment Closeo... 3 of 3 3/29/2016 4:07 PM 2016 ALLDATA, LLC. All Rights Reserved. (Version )

4 1 of 5 3/29/2016 4:08 PM FOLDING TOP STOWAGE COMPARTMENT FRONT OUTER CLOSEOUT PANEL ADJUSTMENT IMPORTANT: Due to the tight clearance of the storage compartment front closeout panel to the upper rear end trim finish panel and the rear roof panel headliner, slowly cycle the folding top a few seconds at a time to ensure panels are moving properly and not hanging up or interfering with the folding top. IMPORTANT: Inspect the closeout panels with the folding top in the down position. Align the closeout panels so there is an even gap to the upper trim finish panel and to each other. Also ensure there is a consistent closeout of the panel seals to the rear compartment lid. Fore/Aft Adjustment Procedure IMPORTANT: The folding top will only remain in partial open or closed position for 3 minutes before the hydraulic pressure is released and the top will descend. For adjustments exceeding this time limit, place the folding top in the service position. Refer to Folding Top Retaining Strap Installation Position.

5 2 of 5 3/29/2016 4:08 PM 2. Loosen the front storage compartment closeout panel hinge bolts (1) and adjust the closeout panel as necessary. Refer to Folding Top Stowage Compartment Closeout Panel Hinge Replacement - Front. 3. Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panel. Parallel Adjustment Procedure

6 3 of 5 3/29/2016 4:08 PM 2. Adjust the stop (1) located on the underside of the front stowage compartment closeout panel link assembly. Refer to Roof Retractable Stowage Compartment Closeout Panel Actuator Cable Replacement. 3.Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panel. Height Adjustment Procedure

7 4 of 5 3/29/2016 4:08 PM 2. Loosen the jam nut (1) on the pin/stop located on the folding top side rail link assembly. thread the pin inward or outward as necessary. 3. Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panels. 4. Re-tighten the jam nut once proper height is achieved. 5. Inspect the folding top for proper operation. Loose or Rattling Outer Panels 2. Tighten the screw (1) under the hinge (2) on the front outer stowage compartment closeout panel link so that the outer panel slightly rubs when its manually cycled outward. Then, back -off the screw slightly. 3. Carefully cycle the folding top, inspecting for proper operation and alignment of the storage compartment closeout panels.

8 5 of 5 3/29/2016 4:08 PM 2016 ALLDATA, LLC. All Rights Reserved. (Version )