w w w. m d u e. i t - i n f m d u e. i t

Transcription

1 PRICED BILL OF QUANTITIES Supply of Emmedue double panel PDM, made up with two EPS slabs, density 30 kg/m 3, cm 5+5 thickness, reinforced with external metal grids realized with steel wires having diameter of mm. 2.5, welded by electrofusion, and internal steel mesh realized with 11 vertical wires of mm. 5 and horizontal wires of mm. 5 every 26 cm., and links between the two slabs and the meshes with connectors of galvanized steel wires of mm. 3 (about 68/mq), for load bearing walls, to finish with the insertion of horizontal stirrups, to compute apart, and to finish on site with casting concrete, with a thickness of the internal layer from 8 to 20 cm. Laying of Emmedue double panel PDM, including the cost for the movement on site, the installation over the foundation rebars, the alignment, plumbing, reinforcing, possible scaffolds, subsequent falsework dismantling, fixing of meshes and the casting concrete inside the panel, concrete and any additional reinforcement steel excluded.

2 Supply of Emmedue single panel PST, consisting of one EPS slab, minimum density 15 kg/m 3, height and thickness variable, reinforced with two steel meshes realized with galvanized steel wire of mm. 2.5 welded by electrofusion, and links between the two meshes and the EPS slab with connectors of galvanized steel wires of mm. 3 (about 68/mq), for outside partition walls or internal partition, finished on site by applying traditional or premixed cement-based plaster for 2.5 cm. thickness. Laying of Emmedue single panels PST, including the cost for the alignment, plumbing, reinforcing, possible scaffolds, subsequent falsework dismantling and fixing of meshes. Supply of Emmedue single panel PSM, consisting of one EPS slab, minimum density 15 kg/m 3, height and thickness variable, reinforced with two steel meshes realized with galvanized steel wire of mm. 2.5 welded by electrofusion, and links between the two meshes and the EPS slab with connectors of galvanized steel wires of mm. 3 (about 68/mq), for load bearing walls or little span covering, finished on site by applying cement-based spritz beton for at least 4 cm. thickness (3.5 cm. over the mesh). Laying of Emmedue single panels PSM, including the cost for the alignment, plumbing, reinforcing, possible scaffolds, subsequent falsework dismantling and fixing of meshes.

3 Supply of Emmedue floor panel PSSG2, consisting of one polystyrene slab, minimum density 15 kg/m 3, suitably shaped (two floor joists for each panel), joists every 56 cm. 10 cm. wide, length and thickness variable, reinforced with two electro-welded meshes of mm. 2.5 wires, and links between the two meshes and the EPS slab with connectors of galvanized steel wires of mm. 3 (about 68/mq), for the realization of floors with the addition of calculation steel and subsequent concrete casting. Supply of Emmedue floor panel PSSG3, consisting of one polystyrene slab, minimum density 15 kg/m 3, suitably shaped (three floor joists for each panel), joists every 37 cm. 10 cm. wide, length and thickness variable, reinforced with two electro-welded meshes of mm. 2.5 wires, and links between the two meshes and the EPS slab with connectors of galvanized steel wires of mm. 3 (about 68/mq), for the realization of floors with the addition of calculation steel and subsequent concrete casting. Laying of Emmedue floor panel PSSG2/3, including the cost for the installation of supports, fixing of meshes, subsequent falsework dismantling and concrete casting, supply of calculation steel and concrete excluded.

4 Supply of Emmedue staircase panel PSSC, consisting of one polystyrene block with density 15 kg/m 3, suitably shaped for every type of step, and reinforced with two metal meshes of mm. 2.5, and links between the meshes and the EPS slab with connectors of galvanized steel wires of mm. 3, for the realization of staircase flights not exceeding m. 6,00 of length, for every type of building, by previous addition of calculation steel and subsequent finishing laying of internal joists (dimensions cm. 13x11). Laying of Emmedue staircase panel PSSC, including the cost for the installation of supports, fixing of meshes, subsequent falsework dismantling and concrete casting, supply of calculation steel and concrete excluded.

5 Supply of electro-welded steel angular mesh RG1, realized with galvanized steel wires 2.5 mm., about 32 cm. wide and 117 cm. long, to install in the corners between panels, internal and external, for the entire height and in the wall-floor joints. Supply of electro-welded steel flat mesh RG2, realized with galvanized steel wires 2.5 mm., about 26 cm. wide and 117 cm. long, to install at 45 in the opening corners, internal and external. Supply of electro-welded steel U mesh RGU, realized with galvanized steel wires 2.5 mm., about 117 cm. long and variable width (it depends from the panel thickness), to install in the perimeter of all the openings. Supply of stirrups SPD of 5 mm. for double panel PDM, to insert horizontally between two consecutive panels. euro/piece