Detail Conditions. Panel Information. Flashing Profiles. Notes. Accessory Profiles. Testing Information. Design/Installation Considerations PEF-1

Transcription

1 Table of ontents Product Page No. Product Page No. Panel Information T3 Panel Profiles... PEF-2 T3 Panel Overview... PEF-2 T6- Panel Profiles... PEF-3 T6- Panel Overview... PEF-3 T- Panel Profiles... PEF-4 T- Panel Overview... PEF-4 Flashing Profiles ustom Eave... PEF-5 leat... PEF-5 ustom Soffit leat... PEF-5 ustom Box Gutter... PEF-5 Box Gutter End... PEF-5 Universal Gutter/Downspout Strap... PEF-5 Downspout... PEF-5 95 Elbow... PEF-5 Downspout Bracket... PEF-5 Valley... PEF-5 ustom Rake... PEF-5 Rakewall... PEF-5 Pitch Break... PEF-5 ustom Peak... PEF-5 Universal Ridge over... PEF-5 oping... PEF-6 ustom Outside orner... PEF-6 Inside orner... PEF-6 ustom Sill/Head... PEF-6 ustom Sill to Soffit... PEF-6 ustom Jamb... PEF-6 Heqad/Jamb over... PEF-6 ustom Head hannel... PEF-6 ustom Base... PEF-6 Detail onditions Eave Detail... PEF-4 Box Gutter Detail... PEF-4 Valley Detail... PEF-5 Rake Detail... PEF-5 Rakewall Detail... PEF-6 Endwall Detail... PEF-6 Peak Detail... PEF-7 Universal Ridge Detail... PEF-7 oping Detail (vertical)... PEF-8 oping Detail (horizontal)... PEF-8 Outside orner Detail (vertical)... PEF-9 Outside orner Detail (horizontal) (+ option)... PEF-9 Inside orner Detail (vertical)... PEF-20 Inside orner Detail (horizontal) (+ option)... PEF-20 Sill/Head Detail (vertical)... PEF-2 Sill/Head Detail (horizontal)... PEF-2 Sill to Soffit Detail (vertical) (+ option)... PEF-22 Sill to Soffit Detail (horizontal) (+ option)... PEF-22 Jamb Detail (vertical)... PEF-23 Jamb Detail (horizontal)... PEF-23 Head hannel Detail (vertical)... PEF-24 Head hannel Detail (horizontal)... PEF-24 Base Detail (vertical)... PEF-25 Base Detail (horizontal)... PEF-25 Notes Notes... PEF-26 ccessory Profiles Universal losure... PEF-7... PEF-7 Rubber Roof Jack... PEF-7 Retro Roof Jack... PEF-7 Rubber Roof Flashing Kit... PEF-7 Touch-Up Paint... PEF-7 Testing Information Section Properties and Load Tables... PEF-8-0 Design/Installation onsiderations Fastener Installation Technique...PEF- ondition of Substructure...PEF- Fastening Patterns... PEF-2-3 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-

2 T3 Panel Overview T3 ROOF PNEL PROFILE 36" overage 6" Pitch 4 5 / 8" 3 / 8" " 3 / 2" 2 / 2" T3 WLL PNEL PROFILE 6" Pitch " 36" overage 3 / 2" 2 / 2" 4 5 / 8" 3 / 8" SLOPE SUBSTRTE OVERGE LENGTH VILBILITY PPLITION FSTENING SYSTEM FSTENERS MTERILS The minimum recommended slope for any T3 panel is :2. Metal Sales recommends that in all roof applications, sealant be used on sidelaps. T3 panel is designed to be utilized over open structural framing, but can easily be used with a solid substrate. The recommended substrate is 5 /8" plywood with a 30 pound felt moisture barrier. To avoid panel distortion, use a properly aligned and uniform substructure. Each panel has a coverage of 36". Lengths under 5'-0" are available with some cutting restrictions. Please consult your Metal Sales branch for maximum panel lengths and recommendations (see PGI-2 and PGI-3 for locations). Panels are available in 24 through 6 gauge. Minimum quantities may apply. ustom capabilities include: -rimp curving on numerous panel profiles. -urving may be convex, concave, or "S" curves. -Perforated panels for wind screens and liner panels. ommercial, Industrial panels. Direct Fastened (exposed). The fastener selection guide should be consulted for choosing proper fasteners for specific applications. Quantity and type of fastener must meet necessary loading and code requirements (see PGI-2-4). Steel grade 50, per STM Optional material: stainless steel, copper, and aluminum. FINISH * crylic oated Galvalume (G) / STM Z55 Prepainted Galvalume / STM Z50 MS olorfast45 ** Fluorocarbon (PVDF) Multi-Pass Kynar Marbilique Plastisol Polyester * Differential appearance of crylic oated Galvalume roofing materials is not a cause for rejection. ** Meets both Kynar 500 and Hylar 5000 specifications. PEF-2 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

3 T6- Panel Overview T6- ROOF PNEL PROFILE 36" overage 5 9 / 6" 5 / 8" 7 3 / 6" Pitch / 2" 3 9 / 6" 3 5 / 8" T6- WLL PNEL PROFILE 36" overage 3 9 / 6" 3 5 / 8" 7 3 / 6" Pitch / 2" 5 9 / 6" 5 / 8" SLOPE SUBSTRTE OVERGE LENGTH VILBILITY PPLITION FSTENING SYSTEM FSTENERS MTERILS The minimum recommended slope for any T6- panel is :2. Metal Sales recommends that in all roof applications, sealant be used on sidelaps. T6- panel is designed to be utilized over open structural framing, but can easily be used with a solid substrate. The recommended substrate is 5 /8" plywood with a 30 pound felt moisture barrier. To avoid panel distortion, use a properly aligned and uniform substructure. Each panel has a coverage of 36". Lengths under 5'-0" are available with some cutting restrictions. Please consult your Metal Sales branch for maximum panel lengths and recommendations (see PGI-2 and PGI-3 for locations). Panels are available in 24 through 6 gauge. Minimum quantities may apply. ustom capabilities include: -rimp curving on numerous panel profiles. -urving may be convex, concave, or "S" curves. -Perforated panels for wind screens and liner panels. ommercial, Industrial panels. Direct Fastened (exposed). The fastener selection guide should be consulted for choosing proper fasteners for specific applications. Quantity and type of fastener must meet necessary loading and code requirements (see PGI-2-4). Steel grade 50, per STM Optional material: stainless steel, copper, and aluminum. FINISH * crylic oated Galvalume (G) / STM Z55 Prepainted Galvalume / STM Z50 MS olorfast45 ** Fluorocarbon (PVDF) Multi-Pass Kynar Marbilique Plastisol Polyester * Differential appearance of crylic oated Galvalume roofing materials is not a cause for rejection. ** Meets both Kynar 500 and Hylar 5000 specifications. Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-3

4 T- Panel Overview T- ROOF PNEL PROFILE 5 / 8" 3 / 4" 3 / 4" 5 / 8" 3 / 4" 4 7 / 8" 34 / 8" overage T- WLL PNEL PROFILE 3 / 4" 34 / 8" overage 4 7 / 8" 5 / 8" 3 / 4" 3 / 4" 5 / 8" SLOPE SUBSTRTE OVERGE LENGTH VILBILITY PPLITION FSTENING SYSTEM FSTENERS MTERILS The minimum recommended slope for any T panel is :2. Metal Sales recommends that in all roof applications, sealant be used on sidelaps. T panel is designed to be utilized over open structural framing, but can easily be used with a solid substrate. The recommended substrate is 5 /8" plywood with a 30 pound felt moisture barrier. To avoid panel distortion, use a properly aligned and uniform substructure. Each panel has a coverage of 34 /8" Lengths under 5'-0" are available with some cutting restrictions. Please consult your Metal Sales branch for maximum panel lengths and recommendations (see PGI-2 and PGI-3 for locations). Panels are available in 24 through 6 gauge. Minimum quantities may apply. ustom capabilities include: -rimp curving on numerous panel profiles. -urving may be convex, concave, or "S" curves. -Perforated panels for wind screens and liner panels. ommercial, Industrial panels. Direct Fastened (exposed). The fastener selection guide should be consulted for choosing proper fasteners for specific applications. Quantity and type of fastener must meet necessary loading and code requirements (see PGI-2-4). Steel grade 50, per STM Optional material: stainless steel, corten, copper, and aluminum. FINISH * crylic oated Galvalume (G) / STM Z55 Prepainted Galvalume / STM Z50 MS olorfast45 ** Fluorocarbon (PVDF) Multi-Pass Kynar Marbilique Plastisol Polyester * Differential appearance of crylic oated Galvalume roofing materials is not a cause for rejection. ** Meets both Kynar 500 and Hylar 5000 specifications. PEF-4 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

5 Flashing Profiles USTOM EVE T3 T6 T 5" 5 /2" 5 3 /4" X* 5 /8" 3" Hem LET 2 /2" /2" 35 USTOM SOFFIT LET Hem T3 T6 T 3 /2" 4" 4 /4" /2" Length 0'-2" - *Specify Slope ngle Length 0'-2" Length 0'-2" USTOM BOX GUTTER T3 T6 T Hem X* " 5" 4" 5" 5 /2" 5" 5 3 /4" Length 0'-2" - *Specify Slope ngle " BOX GUTTER END (RIGHT ND LEFT) 5" 5" 4" " " UNIVERSL GUTTER/ DOWNSPOUT BRKET Hem 6" /2" DOWNSPOUT 6" x 4" 95 0 ELBOW 6" x 4" DOWNSPOUT BRKET 6" 4" 6" 4" 6" Length 0'-0" - (lso available 4" x 3 /2") VLLEY (lso available 4" x 3 /2") USTOM RKE 8" RKEWLL (lso available 4") 2" X* 0" Open Hem 8" 4" 6" Hem 5 /8" Length 0'-0" - *Specify Slope ngle Length 0'-2" Length 0'-2" PITH BREK 4" X* 6" Length 0'-2" - *Specify Slope ngle USTOM PEK 8" Hem X* 8" Open Hem 5 /8" Length 0'-0" - *Specify Slope ngle UNIVERSL RIDGE OVER 2 /2" X* 2 /2" 3 /4" 9" Length 0'-0" - *Specify Slope ngle Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-5

6 Flashing Profiles (cont.) OPING 3 5 /8" 3 /8" 0" Hem 4" 5 /8" USTOM OUTSIDE ORNER 8" Hem 8" INSIDE ORNER 5" 5" Length 0'-0" Length 0'-0" Length 0'-0" USTOM SILL/HED 2 /2" " /2" USTOM SILL TO SOFFIT Hem 2 /2" B /2" USTOM JMB 2 /2" " T3 T6 T /4" 3 /4" 2" T3 T6 T /4" 3 /4" 2" 3 /2" B 4" 4 /4" T3 T6 T /4" 3 /4" 2" Length 0'-0" Length 0'-0" Length 0'-0" HED/JMB OVER USTOM HED HNNEL USTOM BSE 2 7 /8" 8 /8" 2 /2" T3 T6 T " /2" 3 /4" 5 /8" " 3 /4" 5 /8" T3 T6 T /4" 3 /4" 2" Open Hem Length 0'-0" Length 0'-0" Length 0'-0" - Indicates color side of flashing. PEF-6 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

7 UNIVERSL LOSURE ccessory Profiles TPE SELNT RUBBER ROOF JK " x /2" x 50' Polyethylene Foam " x /2" x 0' Polyethylene Foam RUBBER ROOF FLSH KIT 3 /8" X 3 /32" X 50' Single Bead Butyl - Gray TOUH-UP PINT MINI ( /4" to /8" O.D. Pipe) #2 ( 3 /4" to 3" O.D. Pipe) #4 (3" to 6" O.D. Pipe) #6 (6" to 9" O.D. Pipe) #8 (7" to 3" O.D. Pipe) T3 LOSURE 2" x 50'-0" Flash Kit 8" x 50'-0" Flash Kit vailable in pints PVDF / MS olorfast45 Polyethylene Foam T6- LOSURE T- LOSURE Polyethylene Foam Polyethylene Foam Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-7

8 T3 Section Properties ROOF PNEL PROFILE 36" overage 6" Pitch 3 / 8 " 2 3 / 8 " 3 5 / 8 " " Ga Width (in.) Yield KSI Weight PSF SETION PROPERTIES Top in ompression Bottom in ompression LLOWBLE UNIFORM LODS PSF (3 or More Equal Spans) Inward Load Outward / Uplift Load Ixx Sxx Ixx Sxx In 4 /ft In 3 /ft In 4 /ft In 3 /ft Theoretical section properties have been calculated per ISI 200. Specifications for the Design of old-formed Steel Structural Members. Ixx and Sxx are effective section properties for deflection and bending. 2. llowable load is calculated in accordance with ISI 200 specifications considering bending, shear, combined bending and shear and deflection. llowable load considers both 3 and 4 equal span conditions. llowable load does not address web crippling or fasteners/support connection. Panel weight is not considered. 3. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. 4. llowable loads do not include a /3 stress increase in uplift. WLL PNEL PROFILE 36" overage 6" Pitch 3 5 / 8 " 3 / 8 " 4 5 / 8 " " Ga Width (in.) Yield KSI Weight PSF SETION PROPERTIES Top in ompression Bottom in ompression LLOWBLE UNIFORM LODS PSF (3 or More Equal Spans) Inward Load Outward Load Ixx Sxx Ixx Sxx In 4 /ft In 3 /ft In 4 /ft In 3 /ft Theoretical section properties have been calculated per ISI 200. Specifications for the Design of old-formed Steel Structural Members. Ixx and Sxx are effective section properties for deflection and bending. 2. llowable load is calculated in accordance with ISI 200 specifications considering bending, shear, combined bending and shear and deflection. llowable load considers both 3 and 4 equal span conditions. llowable load does not address web crippling or fasteners/support connection. Panel weight is not considered. 3. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. 4. llowable loads do not include a /3 stress increase in uplift. PEF-8 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

9 T6- Section Properties ROOF PNEL PROFILE 36" overage 7 3 / 6 " Pitch 5 / 3 8 " / 2 " 3 / 6 " / 2 " Ga Width (in.) Yield KSI Weight PSF SETION PROPERTIES Top in ompression Bottom in ompression LLOWBLE UNIFORM LODS PSF (3 or More Equal Spans) Inward Load Outward / Uplift Load Ixx Sxx Ixx Sxx In 4 /ft In 3 /ft In 4 /ft In 3 /ft Theoretical section properties have been calculated per ISI 200. Specifications for the Design of old-formed Steel Structural Members. Ixx and Sxx are effective section properties for deflection and bending. 2. llowable load is calculated in accordance with ISI 200 specifications considering bending, shear, combined bending and shear and deflection. llowable load considers both 3 and 4 equal span conditions. llowable load does not address web crippling or fasteners/support connection. Panel weight is not considered. 3. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. 4. llowable loads do not include a /3 stress increase in uplift. WLL PNEL PROFILE 36" overage 7 3 / 6 " Pitch 3 / " / 6 " 5 / 8 " / 2 " Ga Width (in.) Yield KSI Weight PSF SETION PROPERTIES Top in ompression Bottom in ompression LLOWBLE UNIFORM LODS PSF (3 or More Equal Spans) Inward Load Outward Load Ixx Sxx Ixx Sxx In 4 /ft In 3 /ft In 4 /ft In 3 /ft Theoretical section properties have been calculated per ISI 200. Specifications for the Design of old-formed Steel Structural Members. Ixx and Sxx are effective section properties for deflection and bending. 2. llowable load is calculated in accordance with ISI 200 specifications considering bending, shear, combined bending and shear and deflection. llowable load considers both 3 and 4 equal span conditions. llowable load does not address web crippling or fasteners/support connection. Panel weight is not considered. 3. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. 4. llowable loads do not include a /3 stress increase in uplift. Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-9

10 T- Section Properties and Load Tables 34 /8" overage 5 /8" 3 /4" 3 /4" 5 / 8 " 3 /4" 4 7 /8" Pitch Ga Width (in.) Yield KSI 34.25" " " " 33 Weight PSF SETION PROPERTIES Top in ompression Bottom in ompression LLOWBLE UNIFORM LODS PSF (3 or More Equal Spans) Inward Load Outward / Uplift Load Ixx Sxx Ixx Sxx In 4 /ft In 3 /ft In 4 /ft In 3 /ft Theoretical section properties have been calculated per ISI 200 Specification for the Design of old-formed Steel Structural Members. Ixx and Sxx are effective section properties for deflection and bending. 2. llowable load is calculated in accordance with ISI 200 specifications considering bending, shear, combined bending and shear, deflection, and applicable testing when available. llowable load considers the worst case of 3 and 4 equal span conditions. llowable load does not address web crippling or fasteners/support connection and panel weight is not considered. 3. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. 4. llowable loads do not include a /3 stress increase in uplift. TTHMENT DETIL /4"-4 x 7 /8" Stitch Screw #2-4 Self Driller GENERL INFORMTION Substructure T- Panels are designed to be utilized over open structural framing or a solid substrate. overage T- Panels are available in a 3 /4" depth with a coverage width of 34 /8". Length Minimum factory cut length is 5'-0". Maximum panel length is 30'-0". FSTENING PTTERN Ends of Panel /4"-4 x 7 /8" Stitch Screw #2-4 Self Driller Fasteners The fastener selection guide should be consulted for choosing the proper fastener for specific applications. Quantity and type of fastener must meet necessary loading and code requirements. NOTE: ll panels are subject to surface distortion due to improperly applied fasteners. Overdriven fasteners will cause stress and induce oil canning across the face of the panel at or near the point of attachment. vailability Finishes: Kynar 500 (PVDF) standard; optional: multi-pass Kynar, Marblique, Plastisol, Polyester, and MS olorfast45 (SMP) Gauges: 24 ga, 22 ga, 20 ga, and 8 ga Field of Panel /4"-4 x 7 /8" Stitch Screw #2-4 Self Driller PEF-0 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

11 Design / Installation onsiderations FSTENER INSTLLTION TEHNIQUE Recommended Tool Type - Use depth locating nose or adjustable clutch on screw gun to prevent overdrilling and strip out. Do not use impact tools or runners. Seating the washer - pply sufficient torque to seat the washer - do not overdrive the fastener. ORRET Sealing material slightly visible at edge of metal washer. ssembly is watertight. TOO LOOSE Sealing material is not visible; not enough compression to seal properly. TOO TIGHT Metal washer deformed; sealing material pressed beyond washer edge. WOODSREW SELF DRILLER To prevent wobbling - Make sure fastener head is completely engaged in the socket. If the head does not go all the way in the socket - tap the magnet deeper into the socket to allow full head engagement. Metal chips will build up from drilling and should be removed from time to time. Protect drill point - Push only hard enough on the screw gun to engage clutch. This prevents excess friction and burn out of the drill point. orrect pressure will allow screw to drill and tap without binding. Drilling through sheet and insulation - Ease up on pressure when drilling through insulation to avoid striking the purlin or girt with the point - apply more pressure after drill point contacts purlin or girt. Drilling through purlin overlaps - Drilling through lapped purlins requires extra care. Excessive voids between purlins sometimes damages drill points and two self-drillers might be necessary to complete the operation. It is sometimes advantageous to predrill. ONDITION OF SUBSTRUTURE Whether over solid substrate or open structural framing, panel distortion may occur if not applied over properly aligned and uniform substructure. The installer should check the roof deck for squareness before installing Exposed Fastened panels. Several methods can be used to verify squareness of the structure for proper installation of the panels. METHOD "" - One method for checking the roof for squareness is to measure diagonally across one slope of the roof from similar points at the ridge and eave and obtain the same dimension. METHOD "B" - The triangle system may also be used. To use this system measure a point from the corner along the edge of the roof at a module of three (3). Measure a point from the same corner along another edge at a module of four (4). Then by measuring diagonally between the two points established, the dimension should be exactly a module of five (5) to have a square corner. Multiple uses of this system may be required to determine building squareness. If the endwall cannot be made square, the roof system cannot be installed as shown in these instructions. METHOD METHOD B Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-

12 Design / Installation onsiderations (cont.) T3 Fastening Patterns /4"-4 x 7 /8" Stitch Screw (roof only) #2-4 x /4" SD Fastening Pattern (Ends) (roof only) /4"-4 x 7 /8" Stitch Screw (roof only) #2-4 x /4" SD Fastening Pattern (Field) (roof only) T6- Fastening Patterns /4"-4 x 7 /8" Stitch Screw (roof only) #2-4 x /4" SD Fastening Pattern (Ends) (roof only) /4"-4 x 7 /8" Stitch Screw (roof only) #2-4 x /4" SD Fastening Pattern (Field) (roof only) PEF-2 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

13 Design / Installation onsiderations (cont.) T- Roof Fastening Patterns /4"-4 x 7 /8" Stitch Screw (roof only) #2-4 x /4" SD Fastening Pattern (Ends) /4"-4 x 7 /8" Stitch Screw (roof only) (roof only) #2-4 x /4" SD Fastening Pattern (Field) (roof only) T- Wall Fastening Patterns #2-4 x /4" SD Fastening Pattern (Ends) #2-4 x /4" SD Fastening Pattern (Field) Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-3

14 Eave Detail Roof Panel #2-4 x /4" SD Inside losure ustom Eave #2-4 x /4" SD (optional) # /4-4 x 7 /8" Stitch Screw ('-0" o.c.) Outside losure Exposed Fastened Panel Series Box Gutter Detail Roof Panel #2-4 x /4" SD Inside losure /8" x 3 /6" Pop-Rivet ( per gutter strap) ustom Box Gutter Gutter Hanger (optional) Outside losure #2-4 x /4" SD PEF-4 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

15 Valley Detail Roof Panel (bevel cut in field) #2-4 x /4" SD Universal losure (bevel cut) Valley Plate Valley 3" Minimum Exposed Fastened Panel Series Rake Detail Roof Panel #2-4 x /4" SD /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) ustom Rake Rake ngle (by others) #2-4 x /4" SD ('-0" o.c.) (optional) /8" x 3 /6" Pop-Rivet Outside losure leat Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-5

16 Rakewall Detail #2-4 x /4" SD Inside losure Rakewall /4"-4 x 7 /8" ('-0" o.c.) #2-4 x /4" SD ('-0" o.c.) Roof Panel Exposed Fastened Panel Series Endwall Detail #2-4 x /4" SD Inside losure Pitch Break /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) Outside losure #2-4 x /4" SD Roof Panel PEF-6 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

17 Peak Detail Roof Panel /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) Outside losure #2-4 x /4" SD ustom Peak leat /8" x 3 /6" Pop-Rivet (optional) Outside losure Exposed Fastened Panel Series Universal Ridge Detail Roof Panel #2-4 x /4" SD /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) Outside losure Universal Ridge over Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-7

18 oping Detail (Vertical) #2-4 x /4" SD ('-0" o.c.) oping #2-4 x /4" SD ('-0" o.c.) Inside losure (optional) /8" x 3 /6" Pop-Rivet ('-0" o.c.) leat Exposed Fastened Panel Series oping Detail (Horizontal) #2-4 x /4" SD ('-0" o.c.) oping /8" x 3 /6" Pop-Rivet ('-0" o.c.) #2-4 x /4" SD leat PEF-8 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

19 Outside orner Detail (Vertical) Outside orner (optional) /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) #2-4 x /4" SD Exposed Fastened Panel Series Outside orner Detail (Horizontal) Outside orner (optional) /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) Outside losure #2-4 x /4" SD Detail Optional /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) /8" x 3 /6" Pop-Rivet ('-0" o.c.) Metal losure (field cut and formed) Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-9

20 Inside orner Detail (Vertical) Inside orner /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) (optional) #2-4 x /4" SD Exposed Fastened Panel Series Inside orner Detail (Horizontal) Inside orner /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) (optional) Outside losure #2-4 x /4" SD #2-4 x /4" SD Detail Optional /4"-4 x 7 /8" Stitch Screw ('-0" o.c.) /8" x 3 /6" Pop-Rivet ('-0" o.c.) Metal losure (field cut and formed) PEF-20 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

21 Sill/Head Detail (Vertical) #2-4 x /4" SD Inside losure (optional) ustom Sill/Head Head/Jamb over Exposed Fastened Panel Series Sill/Head Detail (Horizontal) #2-4 x /4" SD #2-4 x /4" SD ('-0" o.c.) ustom Sill/Head Head/Jamb over Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-2

22 Sill to Soffit Detail (Vertical) (and option) (optional) Inside losure #2-4 x /4" SD ustom Sill to Soffit /8" x 3 /6" Pop-Rivet ('-0" o.c.) Detail Optional Soffit Panel ustom Base ustom Soffit leat Exposed Fastened Panel Series Sill to Soffit Detail (Horizontal) (and option) #2-4 x /4" SD #2-4 x /4" SD ('-0" o.c.) ustom Sill to Soffit /8" x 3 /6" Pop-Rivet ('-0" o.c.) Detail Optional Soffit Panel ustom Base ustom Soffit leat PEF-22 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

23 Jamb Detail (Horizontal) #2-4 x /4" SD Inside losure (optional) ustom Jamb Head/Jamb over Exposed Fastened Panel Series Jamb Detail (Vertical) #2-4 x /4" SD #2-4 x /4" SD ('-0" o.c.) ustom Jamb Head/Jamb over Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-23

24 Head hannel Detail (Vertical) #2-4 x /4" SD Inside losure (optional) ustom Head hannel Head/Jamb over Exposed Fastened Panel Series Head hannel Detail (Horizontal) #2-4 x /4" SD #2-4 x /4" SD ('-0" o.c.) ustom Head hannel Head/Jamb over PEF-24 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)

25 Base Detail (Vertical) #2-4 x /4" SD Inside losure (optional) ustom Base Exposed Fastened Panel Series Base Detail (Horizontal) #2-4 x /4" SD #2-4 x /4" SD ('-0" o.c.) ustom Base Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office) PEF-25

26 Notes PEF-26 Metal Sales Manufacturing orporation/ Subject to change without notice/ Effective Date 9/ (orporate Office)