CERTIFICATE OF APPROVAL No CF 5158 WHITE ALUMINIUM ENTERPRISES L.L.C.

Transcription

1 CERTIFICATE OF APPROVAL No CF 5158 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of Sector M-21, Mussafah Industrial Area, PO Box 30665, Mussafah, Abu Dhabi, UAE Tel: Fax: Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT Fire Rated Glazed Steel Doors TECHNICAL SCHEDULE TS12 Hinged or Pivoted Fire Resisting Pedestrian Type Doorsets with Metallic Leaves and Frames Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Issued: 09 Chairman - Management Council Valid to: 08 May 2018 Page 1 of 3

2 CERTIFICATE No CF 5158 FIRE RATED GLAZED DOORSETS 1. This approval relates to the use of the above doorsets in providing a fire resistance of up to 60 minutes integrity, as defined in BS EN : This certification is designed to demonstrate compliance of the product or system specifically with Approved Document B (England and Wales), Section 2 of the Technical Standards (Scotland), Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account. 3. The doors are approved on the basis of: i) Initial type testing. ii) A design appraisal against TS12. iii) Certification of quality management system to ISO 9001: iv) Inspection and surveillance of factory production control. v) Audit testing as defined in TS The doorsets comprise glazed mild steel door leaves hung within mild steel frames. 5. This approval is applicable to complete doorsets only. 6. This approval is applicable to single-acting, single and double-leaf, latched (and bolted for double-leaf option) doorsets at leaf dimensions up to those given in Table Hardware items, including closing devices, shall be CERTIFIRE approved or otherwise as specified in the data sheet. 8. The doorsets shall be mechanically fixed to wall constructions having a fire resistance of at least the same period as the doorset. 9. This certificate does not include any approval relating to the mechanical requirements of the doorsets specified in TS12. Page 2 of 3 Signed Issued: 09 Valid to: 08 May 2018

3 CERTIFICATE No CF 5158 FIRE RATED GLAZED DOORSETS Table 1. Maximum Permitted Door Leaf Dimensions Doorset Configuration Integrity and Insulation (I 2 ) (mins) Maximum Height (mm) Maximum Width (mm) Subject to Maximum Area of (m 2 ) Single-acting, single-leaf, latched Single-acting, single-leaf, latched Single-acting, double-leaf, latched and bolted Single-acting, double-leaf, latched and bolted Doorsets shall be single-acting, single or double leaf. All doorsets shall be latched and for double-leaf doorsets the inactive leaf shall be flush bolted. 11. Labels to the CERTIFIRE design referencing WHITE ALUMINIUM ENT. L.L.C., CERTIFIRE and CERTIFIRE Ref. No. CF 5158 shall be affixed to each door in the prescribed position. 12. This approval relates to on-going production. The product and/or its immediate packaging is identified with the manufacturer s name, the product name or number, the CERTIFIRE name and mark together with the CERTIFIRE Certificate number (CF 5158) and application where appropriate. Page 3 of 3 Signed Issued: 09 Valid to: 08 May 2018

4 CONSTRUCTIONAL SPECIFICATION FOR CERTIFIRE APPROVED FIRE RATED GLAZED DOORSETS Introduction This document specifies constructional and other details for the Fire Rated Glazed doorsets manufactured by and certified by CERTIFIRE under certificate No. CF Only doors complying with the details of this document may be marked or marketed as CERTIFIRE approved. Any change to, or deviation from, this specification requires the agreement of CERTIFIRE. CERTIFIRE approval is applicable to complete doorsets only. Scope of Approval As defined in certificate of approval No. CF 5158 Drawings Showing Elevation Various Cross Sections through Framing Members Constructional Specification CF 5158 Page 1 of 6

5 Vertical Section B-B Section C-C Frame Header and Leaf Profile Section Constructional Specification CF 5158 Page 2 of 6

6 Leaf Profile Bottom Section Leaf and Frame Profile (horizontal Section) Meeting Edges of the Leaf Profile Constructional Specification CF 5158 Page 3 of 6

7 Frame Profile and Associated Item Specifications: Constructional Specification CF 5158 Page 4 of 6

8 Constructional Specification CF 5158 Page 5 of 6

9 Glazing Details and Specifications: Glass Material Manufacturer Reference Dimensions Setting Blocks Glass White Aluminium Fabrication PYRAWHITE E60/EW x 2093 x 6mm thick glass 80 x 5 x 8 (w x h x depth) Fixing method The glass was placed within the opening over a 80 x 5 x 8 (w x h x depth) Flammi 12 (Gluske) setting blocks after the frame and leaf profiles were installed. The final beading was clipped on after 6mm ceramic tape was placed on either side of the glass perimeter adjacent to the framing profiles. The spacing between the glass and frame were bottom vertical top Intumescent Glazing Tape Material Manufacturer Reference Dimensions Fixing method Ceramic glazing edge seal Gluske Kerafix Flexlit 15 x 5mm (w x thk) (Uncompressed thickness) Compressed between the glazing beads. See drawings for details. Constructional Specification CF 5158 Page 6 of 6

10 CF 5158 DATA SHEET FIRE RATED GLAZED DOORSETS 1. General DATA SHEET These doorsets have been fire tested and certified by CERTIFIRE as being capable of providing fire resistance of up to 60 minutes integrity, for the single-acting configurations, as defined in BS EN : 2008, when installed in accordance with the following conditions. In recognition of this, the leaf carries a prefixed label on the top or hanging edge of the door, issued under the terms of the CERTIFIRE scheme. This label uniquely identifies the door leaf, the manufacture of which complies with BS: ISO 9001:2008 for quality systems and is subject to on-going surveillance. This label shall not be removed. It is emphasised that the certification is conditional upon the following instructions being complied with in their entirety. Failure to do so will invalidate this approval and may jeopardise the fire performance of the door. Door assemblies supplied pre-fitted with components by may be considered to meet the requirements in respect of those items. 2. Door Leaf Dimensions The doorsets may be used in single-acting, single or double-leaf, latched (and bolted for double-leaf options), metal framed, metal leaf configurations. The doorsets shall be of mild steel, uninsulated framed glazed construction. The maximum door leaf dimensions are given in Table 1. Table 1. Maximum Permitted Door Leaf Dimensions Doorset Configuration Integrity and Insulation (I 2 ) (mins) Maximum Height (mm) Maximum Width (mm) Subject to Maximum Area of (m 2 ) Single-acting, single-leaf, latched Single-acting, single-leaf, latched Single-acting, double-leaf, latched and bolted Single-acting, double-leaf, latched and bolted Data Sheet CF 5158 Page 1 of 3

11 Supporting Construction The door assemblies are approved to be installed into reinforced concrete or masonry with a fire resistance at least equal to that of the doorset to be installed. 4. Installation Frame jambs fixed at four equidistant positions. Single-leaf doorset head members to have a minimum of 1 no. fixing on widths over 900 mm. Double-leaf doorset head members to have 2 no. fixings. For masonry or concrete, doorset to be installed using steel anchor bolts minimum 10 mm diameter by 100 mm long 5. Seals Any seals shall be CERTIFIRE approved for use on uninsulated steel doorsets. 6. Hinges Hinges shall be of steel construction and shall be CE marked for use on fire resisting steel doors. Alternatively, the door may be hung on the specific hinges detailed below: Number: 2 hinges up to 2295 mm high, 3 hinges over 2295 mm high Reference: Forster Any other CERTIFIRE approved hinges subject to the conditions contained within the relevant certificate. 7. Lock and Latches Locks and latches shall be CE Marked for use on fire resisting steel doors, in addition to the following specifications: Alternative locks/latches which have been CERTIFIRE approved for use in steel doorsets are deemed to be suitable for use. No restriction on type of metallic lever handles. Locks or latches must be fitted to single-leaf doorsets and the active leaf of double-leaf doorsets. Specific alternative lock and associated components as detailed below are also included in this scope of approval: Door Lock Manufacturer: Forster Reference: Dimensions: 45 mm wide by 190 mm high Handles Manufacturer: Forster Reference: Dimensions: 28 mm wide by 320 mm high Data Sheet CF 5158 Page 2 of 3

12 8. Self Closing Devices 9. Bolts A self-closing device is required to be fitted to satisfy fire regulations and if fitted shall be a CERTIFIRE approved and CE Marked product for the required application and door type. Note: closers with mechanical hold-open mechanisms are not permitted to be used. Flush bolts or shoot bolts of all steel construction must be fitted to the inactive door leaf of any double-leaf doorset. The inactive door leaf shall incorporate such a bolting device at both the head and base of the leading edge which shall provide at least 10 mm engagement. Specific alternative bolts as detailed below are also included in this scope of approval: Manufacturer: Dimensions: Merit 25 mm wide by 173 mm high 10. Glazed Apertures All apertures to be factory prepared by. Doorsets to be glazed (where r) using an alternative CERTIFIRE approved system (glass and glazing gasket). The relevant system shall be approved for use within an uninsulated steel door construction. The maximum opening or pane dimensions specified within the CERTIFIRE approval for the glazing system shall not be exceeded regardless of the maximum leaf dimensions permitted in this approval. Should a door leaf be required with glazed aperture dimensions that exceed that approved the glass to be used, then the door leaves may incorporate transoms to reduce the aperture dimension. Additionally, any edge cover and/or expansion allowance requirements specified by the glass approval MUST be complied with. Failure to comply with such requirements may invalidate this approval. A list of approved and acceptable glass types can be found at the following weblink: Further Information Further information regarding the details contained in this data sheet may be obtained from. (Tel: ). Further information regarding the CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: + 44 (0) ). Data Sheet CF 5158 Page 3 of 3