YOUR BEST CONNECTIONS 1 HALFEN GmbH

Transcription

1 DECLARATION OF PERFORMANCE HALFEN HB-BZ/HB-BZ-IG WEDGE ANCHOR No. H40-07/ Unique identification code of the HALFEN HB-BZ/HB-BZ-IG WEDGE ANCHOR product-type Type, batch or serial number or any other element HALFEN HB-BZ/HB-BZ-IG WEDGE ANCHOR see ETA-07/0249 allowing identification of the construction product as Annex A; Batch number: see packaging of the product required pursuant to Article 11(4) Intended use or uses of the construction product, in accordance with the applicable harmonized technical specification, as foreseen by the manufacturer: Generic type and use Torque-controlled expansion anchor For use in Cracked or Non-cracked concrete C20/25 - C50/60 (EN 206) 3. Base material / base material strength Zinc-plated steel: dry internal conditions only covered sizes: HB-BZ: M8, M10, 70 M12, M16, M20, M24, M27 HB-BZ-IG: M6, M8, M10, M12 Stainless steel (marking A4): internal and external use without particular aggressive conditions covered sizes: HB-BZ: M8, M10, 70 M12, M16, M20, M24 HB-BZ-IG: M6, M8, M10, M12 Highly corrosion resistant steel (marking HCR): internal and external use with particular aggressive conditions covered sizes: HB-BZ: M8, M10, 70 M12, M16, M20, M24 HB-BZ-IG: M6, M8, M10, M12 Temperature range (if applicable) Name, registered trade name or registered trade mark and contact address of the manufacturer as required pursuant to Article 11(5) Where applicable, name and contact address of the authorized representative whose mandate covers the tasks specified in Article 12(2) System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V In case of the declaration of performance concerning a construction product covered by a harmonised standard In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued HALFEN GmbH, Liebigstraße 14, Langenfeld, Germany - System 1 - Deutsches Institut für Bautechnik, Berlin issued ETA-07/0249 on the basis of ETAG 001. The notified body 0756-CPD performed under system 1: (i) initial inspection of the manufacturing plant and of factory production control; (ii) continuous surveillance, assessment and evaluation of factory production control. 1

2 9. Declared performance Essential Characteristics Characteristic resistance for static and quasi static action Characteristic resistance for seismic performance categories C1 and C2 Displacements under tension and shear loads Design Method ETAG 001; Annex C CEN/TS ETAG 001; Annex C CEN/TS ETAG 001; Annex C Resistance to fire CEN/TS Where pursuant to Article 37 or 38 in the Specific Technical Documentation has been used, the requirements with which the product complies HB-BZ ETA-Annex C1 to C5 Performance EOTA TR 045 ETA-Annex C6 - ETA-Annex C9 to C10 ETA-Annex C7 to C8 - HB-BZ-IG ETA-Annex C11 to C13 ETA-Annex C15 ETA-Annex C14 Harmonized Technical Specification ETAG The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Langenfeld, Signed for and on behalf of the manufacturer by Richard Wachter (Managing Director) ppa. Dr.-Ing. Dirk Albartus (Manager Engineering) H /16-E 2

3 Annex C1: 3

4 Annex C2: 4

5 Annex C3: 5

6 Annex C4: 6

7 Annex C5: 7

8 Annex C6: 8

9 Annex C7: 9

10 Annex C8: 10

11 Annex C9: 11

12 Annex C10: 12

13 Annex C11: 13

14 Annex C12: 14

15 Annex C13: 15

16 Annex C14: 16

17 Annex C15: 17