High Quality User-Friendly Epoxies - Resins - Coatings - Adhesives

Transcription

1 415 E. Venice Avenue Venice, FL (800) Tel (941) Fax High Quality User-Friendly Epoxies - Resins - Coatings - Adhesives Innovation Custom Formulas Marine Automotive Electrical Industrial

2 MRO Products - Concrete Repair EPO Resurfacer RES50 50 lb Kit 3-Component epoxy compound for resurfacing large areas of worn concrete EPO Resurfacer LTC RESLT50 50 lb Kit 3-Component epoxy compound for resurfacing large areas of worn concrete Low-temperature cure (or fast cure at room temperature) EPO Patch & Grout EP.75 EP3 EP10 EP50 (PT A&B only) 10 Lb. Kit 50 Lb. Kits 3-component epoxy compound for patching holes in concrete or for use as grout for setting machinery or tile. EPO Patch LTC EPLT.75 EPLT3 EPLT10 EPLT50 (PT A&B only) 10 Lb. Kit 50 Lb. Kits 3-component epoxy compound for patching holes in concrete or for use as grout for setting machinery or tile. Low-temperature cure (or fast cure at room temperature) EP-Unite Clear EU.75 EU3 Epoxy compound for adhering thin layers of new concrete to old, without cracking of new concrete as it dries. Clear in color. EPO Anchoring Cement EA10 EA45 10 Lb. Kit 45 Lb. Kit 3-component epoxy compound for cementing anchor bolts into concrete. Available Color: EPO Joint Sealant EJ1 EJ2 EJ10 1 Gal. Kit 2 Gal. Kit 10 Gal. Kit Semi-rigid epoxy compound for filling saw-cut joints in concrete. EPO Joint Sealant LTC EJLT1 EJLT2 EJLT10 1 Gal. Kit 2 Gal. Kit 10 Gal. Kit Semi-rigid epoxy compound for filling saw-cut joints in concrete. Low-temperature cure (or fast cure at room temperature)

3 MRO Products - Coatings EPO Coat VA VA.5 VA1 VA2 VA10 1/2 Gal. Kit 1 Gal. Kit 2 Gal. Kit 10 Gal. Kit High-Solids general purpose 2-component epoxy coating for concrete floors and for machinery. 672 Green 531 Medium Beige 642 Light Beige 386 Off White 001 White 907 Safety Yellow 526 Light Blue 000 Black EPO Coat Zinc Rich Primer ECZP22 22 Lb. Gal. Kit Heavily zinc-filled corrosion-resistant epoxy metal primer EPO Coat H3H ECH3P.75 ECH3P3 100% Solids chemical-resistant and wear-resistant 2-component epoxy coating. 001 White 531 Medium Beige Clear EPO Coat NS-100 NS100.5 Ns /2 Gal. Kit 1 Gal. Kit 3:1 3:1 100% Solids non-slip epoxy coating 907 Safety Yellow EPO Seal 100 ES ES1003 ES Gal. Kit 100% Solids 2-component general purpose epoxy concrete sealer.

4 Adhesives Products How to Apply Epoxy Floor Coating Paint Floor coating with epoxy paint before After proper surface preparation, application technique is the next most important step in floor coating. First you must assess the mix ratio of the product you are using. All Dynamis epoxy products have simple or mix ratios. You mix either 1 unit of part A by volume to 1 unit of part B by volume or you mix 2 units part A by volume to 1 unit part B by volume. Our simple mix ratios allow you to easily measure out partial kits if you will not be coating enough floor to use an entire kit. Our EPO Coat H3H 100% solids epoxy coating system has a mix ratio. Mixing Epoxy Floor Paint After making note of the mix ration, you must find measuring containers and a mixing container. Ideally you ll want a separate measuring container for part A and part B. You should then mix each component thoroughly in its original container in case the material has separated, to ensure a good mix. Measure out your components into the mixing container observing the proper mixing ratio. Once measured out, it s best to use a drill with a mixing blade to ensure a thorough mix. Stir with the drill for 2-3 minutes. Then carefully scrape the sides and bottom of the container with the mixer and then stir for another 1-2 minutes. After mixing, it s important to note that some epoxy coatings require a sweatin time of minutes. This helps to achieve a more rapid and thorough cure for a slower-curing product once the material is on the floor. Our EPO Coat H3H 100% solids epoxy coating system does not require this sweat-in period. After mixing, and the sweat-in period if necessary, you must choose a roller. For epoxies you will generally want to choose a roller with a very short nap, 1/8 to ¼, with a phenolic core. This type of roller will hold up and won t shed hairs into your beautiful new floor even as the epoxy becomes thicker and stickier as it approaches the end of its working life. Finished Application Roll the coating out observing the approximate coverage information for the specific coating that you are using. It s important not to stretch the material too thin as it will simply soak into the concrete and leave you with very little external protection or aesthetic effect. On bare concrete you will want to apply two coats, the first one thinned with acetone or MEK (please check your local laws to ensure that this is legal at your location) to provide a solid mechanically-bonded base coat. When going over an existing epoxy floor that is mostly intact one coat will generally suffice. If applying two coats, the second coat can be applied as soon as the first coat is dry to walk on and tack-free. Once rolled, remove any masking as soon as possible to avoid it sticking to the freshly coated floor. You will be able to walk on it after 8-12 hours, but avoid any car or forklift traffic for 72 hours to avoid leaving tire marks. If you follow these steps you will have a very durable epoxy floor that will take a lot of abuse and look very good at the same time.

5 Surface Preparation Best coating system only as good as the surface it is applied to Acid-etching, dissolve concrete dust on unprepared concrete Surface abrasion, where it is difficult to contain water used in acid-etching The first and arguably most important step in any floor coating job is surface preparation. After all, even the very best coating system is only as good as the surface it is adhered to. With that in mind, the first step is cleaning. All dust and dirt must be removed from the surface. Any loose chips of a previous coating must be removed. Any oil must be carefully removed with soap and hot water or else the coating will surely peel in those areas. After cleaning, the grain of the concrete must be exposed to ensure maximum adhesion of the coating to the concrete. There are a primary types of surface preparation for a concrete floor: acid-etching and surface abrasion. Prepare the concrete surface with acid etching Acid-etching is the process of using an acid, usually muriatic acid, to dissolve the concrete dust that is always present on unprepared concrete. Since concrete dust is alkali, the acid does a good job of reacting to and dissolving the dust and then it can be removed with a simple wash-down. To accomplish acid-etching, simply take muriatic acid, available at any pool supply store, and dilute it with water at a ratio of 1 part acid to 3 parts water. This can be applied to the concrete using a watering can. When you can just start to see the grain of the concrete coming through, neutralize the acid solution with clear ammonia. The resulting solution is nonhazardous and can be washed down with water. There are multiple methods for surface abrasion including sandblasting, shotblasting, and grinding. Each of these methods provides a good solid grain in the concrete for the coating to adhere to. The primary disadvantage of surface abrasion vs acid-etching is the large amount of concrete dust that is generated. However, surface abrasion is ideal for situations where it would be difficult to contain the large amount of water used in acid-etching. All of these procedures may seem like a lot of extra work, but ultimately a good surface preparation will ensure that your floor coating will withstand the test of time. When it s time to recoat, a basic cleaning and a quick sanding with a sanding disk will be all that s required to prepare the epoxy surface for a new coating.

6 Epoxy Products - Industrial Dynamic Balancing Compound EPO Dynaweight ED2 ED15 ED60 ED150 2 lb. Kit 15 lb. Kit 60 lb. Kit 150 lb. Kit Epoxy compound for dynamic balancing of rotating parts. Ideal for use in electric motor manufacturing and repair. 40-year industry history. EPO Dynaweight BAL-VI ED62 ED616 ED676 2 lb. Kit 16 lb. Kit 76 lb. Kit Improved epoxy compound for dynamic balancing of rotating parts. Ideal for use in electric motor manufacturing and repair. Mix Ratio by weight or volume. EPO Dynaweight BAL-I-FS ED12 ED116 2 lb. Kit 16 lb. Kit Intermediate cure epoxy compound for dynamic balancing of rotating parts. Ideal for use in electric motor manufacturing and repair. EPO Dynaweight BAL-XV-FS ED152 ED lb. Kit 16 lb. Kit Rapid cure epoxy compound for dynamic balancing of rotating parts. Ideal for use in electric motor repair. Epoxy Products - Potting Compounds Pour Flex PF1 PF2 PF8 1 Pint 16 oz. Kit 1 Quart 32 oz. Kit 1 Gallon 8 lb. Kit Semi-flexible epoxy potting compound for sealing leads in submersible pumps. Pour Flex PF3502 PF3508 PF Quart 32 oz. Kit 1 Gallon 8 lb. Kit 2 Gallon 16 lb. Kit Semi-flexible epoxy potting compound for sealing leads in submersible pumps. Slower cure version for larger pours up to 2 gallons at once.

7 Industrial Adhesive Products EPO Gel HT EGHTQT 1 Quart Kit Highly thixatropic epoxy gel adhesive ETHTGL 1 Gallon Kit EGHT10GL 10 Gallon Kit PLA 5 PLA550 PLA ml cartridge 400 ml cartridge Permanent Liquid Adhesive, 5 Minute Cure time PLA 10 PLA1050 PLA ml cartridge 400 ml cartridge Permanent Liquid Adhesive, 10 Minute Cure time PLA 60 PLA6050 PLA ml cartrdige 400 ml cartridge Permanent Liquid Adhesive, 60 Minute Cure time PLA 100 PLA10050 PLA ml cartridge 400 ml cartridge Permanent Liquid Adhesive, 100 Minute Cure time Wear and Abrasion Products Product Name Part No. Unit Size Mix Ratio Ratio Description Z-TEC 751 Z-TEC 752 Z-TEC 753 ZT751 ZT752 ZT753 2 lbs. Kit 2 lbs. Kit 2 lbs. Kit Ceramic-filled epoxy repair putty. Ceramic-filled epoxy repair base coat. Ceramic-filled epoxy repair top coat. Steel-Tec 801 ST801 2 lbs. Kit Steel-filled epoxy repair putty AS-PCL ASPCL lbs. Kit Epoxy based ceramic wear compound Marine Products Laminating Resin LA 32 LA 128 LA Quart Can 1 Gallon Can 5 Gallon Pail Low-viscosity Epoxy laminating resin GP Resin GP 32 GP 128 GP Quart Can 1 Gallon Can 5 Gallon Pail Medium viscosity general purpose epoxy resin LAM/GP Hardener (10, 30, 60, or 120) LAM 32 LAM 128 LAM Quart Can 1 Gallon Can 5 Gallon Pail Hardener for Lam and GP Resins. 10, 30, 60, & 120 min. po life available Teak Adhesive TA 256 TA Gallon 10 Gallon Epoxy adhesive for adhering teak to surfaces EPO Coat CT 100 EPO EPO EPO Pint 2 Quart 2 Gallon Coal-tar epoxy coating

8 415 E. Venice Avenue (800) Tel Venice, FL (941) Fax 9/2013