Anchor Fastening Technology Manual 09 / 2012

Transcription

1 Anchor Fastening Technology Manual 09 /

2 Forword Foreword Dear customer, As it is our ambition to be the worldwide leader in fastening technology, we are continously striving to provide you with state-of-the-art technical information reflecting the latest developments in codes, regulations and approvals and technical information for our products. The Fastening Technology Manuals for Post-installed Anchors and for Anchor Channel reflect our ongoing investment into long term research and development of leading fastening products. This Fastening Technology Manual for Post-installed Anchors should be a valuable support tool for you when solving fastening tasks with Post-installed Anchor fastening technology. It should provide you with profound technical knowhow, and help you to be more productive in your daily work without any compromise regarding reliability and safety. As we strive to be a reliable partner for you, we would very much appreciate your feedback for improvements. We are available at any time to answer additional questions that even go beyond this content. Raimund Zaggl Business Unit Anchors 1

3 Important notices Important notices 1. Construction materials and conditions vary on different sites. If it is suspected that the base material has insufficient strength to achieve a suitable fastening, contact the Hilti Technical Advisory Service. 2. The information and recommendations given herein are based on the principles, formulae and safety factors set out in the Hilti technical instructions, the operating manuals, the setting instructions, the installation manuals and other data sheets that are believed to be correct at the time of writing. The data and values are based on the respective average values obtained from tests under laboratory or other controlled conditions. It is the users responsibility to use the data given in the light of conditions on site and taking into account the intended use of the products concerned. The user has to check the listed prerequisites and criteria conform with the conditions actually existing on the job-site. Whilst Hilti can give general guidance and advice, the nature of Hilti products means that the ultimate responsibility for selecting the right product for a particular application must lie with the customer. 3. All products must be used, handled and applied strictly in accordance with all current instructions for use published by Hilti, i.e. technical instructions, operating manuals, setting instructions, installation manuals and others. 4. All products are supplied and advice is given subject to the Hilti terms of business. 5. Hilti s policy is one of continuous development. We therefore reserve the right to alter specifications, etc. without notice. 6. The given mean ultimate loads and characteristic data in the Anchor Fastening Technology Manual reflect actual test results and are thus valid only for the indicated test conditions. Due to variations in local base materials, on-site testing is required to determine performance at any specific site. 7. Hilti is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inability to use the products for any purpose. Implied warranties of merchantability or fitness for a particular purpose are specifally excluded. Hilti Corporation FL-9494 Schaan Principality of Liechtenstein Hilti = registred trademark of the Hilti Corporation, Schaan 2

4 Contents Contents Anchor technology and design...7 Anchor selector...8 Legal environment...20 Approvals...22 Base material...28 Anchor design...34 Design example...44 Corrosion...48 Dynamic loads (seismic, fatigue, shock)...52 Resistance to fire...58 Mechanical anchoring systems...71 HDA Design anchor...72 HSL-3 carbon steel, heavy duty anchor...88 HSL-GR stainless steel, heavy duty anchor HSC-A Safety anchor HSC-I Safety anchor HST Stud anchor HSA Stud anchor HSV Stud anchor HLC Sleeve anchor HAM Hard sleeve anchor HUS-HR Screw anchor, stainless steel HUS Screw anchor, carbon steel HUS 6 Screw anchor, Redundant fastening HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs HUS 6 / HUS-S 6 Screw anchor HKD Push-in anchor, Single anchor application HKD Push-in anchor, Redundant fastening HKV Push-in anchor, Single anchor application HUD-1 Universal anchor HUD-L Universal anchor HLD Light duty anchor HRD-U 10 / - S 10 / -U 14 Frame anchor HRD Frame anchor, Redundant fastening HPS-1 Impact anchor HHD-S Cavity anchor HCA Coil anchor HSP / HFP Drywall plug HA 8 Ring / hook anchor DBZ Wedge anchor HT Metal frame anchor HK Ceiling anchor HPD Aerated concrete anchor HKH Hollow deck anchor HTB Hollow wall metal anchor IDP Insulation fastener IZ Insulation fastener IDMS / IDMR Insulation fastener

5 Contents Adhesive anchoring systems HVZ Adhesive anchor HVU with HAS/HAS-E rod adhesive anchor HVU with HIS-(R)N adhesive anchor Hilti HIT-RE 500-SD with HIT-V rod Hilti HIT-RE 500-SD with HIS-(R)N Hilti HIT-RE 500-SD with rebar Hilti HIT-RE 500 with HIT-V / HAS in hammer drilled holes Hilti HIT-RE 500 with HIT-V / HAS in diamond drilled holes Hilti HIT-RE 500 with HIS-(R)N Hilti HIT-RE 500 with rebar in hammer drilled holes Hilti HIT-RE 500 with rebar in diamond drilled holes Hilti HIT-HY 200 with HIT-Z Hilti HIT-HY 200 with HIT-V Hilti HIT-HY 200 with HIS-(R)N Hilti HIT-HY 200 with rebar Hilti HIT-HY 150 MAX with HIT-TZ Hilti HIT-HY 150 MAX with HIT-V / HAS Hilti HIT-HY 150 MAX with HIS-(R)N Hilti HIT-HY 150 MAX with rebar Hilti HIT-CT 1 with HIT-V Hilti HIT-HY 150 with HIT-V / HAS Hilti HIT-HY 150 with HIS-(R)N Hilti HIT-HY 150 with rebar Hilti HIT-ICE with HIT-V / HAS Hilti HIT-ICE with HIS-(R)N Hilti HIT-ICE with rebar Hilti HIT-HY 70 injection mortar for masonry HRT-WH Rail anchor with Hilti HVU or Hilti HIT-RE HRT Rail anchor with Hilti HIT-RE HRC / HRC-DB Rail anchor with Hilti HIT-RE HRA Rail anchor with Hilti HIT-RE 500 or HVU-G/EA glass capsule HRT-I Rail anchor with Hilti HIT-RE HRT-IP Rail Anchor for cast-in/top down construction method Post-installed rebar connections Basics, design and installation of post installed rebars Hilti HIT-RE 500-SD post-installed rebars Hilti HIT-RE 500 post-installed rebars Hilti HIT-HY 200 post-installed rebars Hilti HIT-HY 150 post-installed rebars Hilti HIT-HY 150 MAX post-installed rebars Hilti worldwide

6 IZ Insulation fastener IZ Insulation fastener Anchor version IZ Benefits - Insulation fastener esp. for plastered surfaces - 30mm setting depth - perfect flush setting Concrete Solid brick Hollow brick Insulation Basic loading data (for a single anchor) All data in this section applies to - Correct setting (See setting instruction) - No edge distance and spacing influence - Base material as specified in the table - Minimum base material thickness Recommended loads Solid clay brick Mz 12 2,0 Solid sand-lime brick KS 12 1,8 Hollow clay brick Hlz 12 1,0 Hollow sand-lime brick KSL 12 1,4 a) Drilling without hammering IZ N rec [kn] 0,2 N rec [kn] 0,2 N rec [kn] 0,2 N rec [kn] 0,13 a) N rec [kn] 0,17 Recommended pull-through loads and number of IZ in insulation Pull-through loads [kn] IZ Min. number of fasteners Expanded polystyrene (EPS 0,15 5 Mineral wool, type HD 0,15 5 Mineral wool, type WV 0,15 4 Mineral wool, type lamella, with slip-on-plate HDT 140 0,

7 IZ Insulation fastener Materials Material quality Part Anchor sleeve Expansion pin Material Polypropylene Polyamide, Anchor dimensions Anchor size IZ Minimum thickness of insulation h D,min [mm] 0 Maximum thickness of insulation h D,max [mm] 180 Diameter of the sleeve d nom [mm] 8 Minimum length of the sleeve l 1,min [mm] 70 Maximum length of the sleeve l 1,max [mm] 210 Minimum length of the screw l 2,min [mm] 65 Maximum length of the screw l 2,max [mm] 205 l 1 h nom h ef d nom 60 l 2 Setting installation equipment Anchor size Rotary hammer Other tools IDP TE2 TE16 Hammer, stepped-drill TE-C 8/ is necessary when t tol > 30mm 341

8 IZ Insulation fastener Setting instruction Setting details: h 1 h nom h ef t tol h D h 342

9 IZ Insulation fastener Setting details IZ Anchor version Nominal diameter of drill bit d o [mm] 8 Cutting diameter of drill bit d cut [mm] 8,45 Depth of drill hole h 1 [mm] 50 Effective anchorage depth h ef [mm] 30 Overall embedment depth h nom [mm] 40 Installation temperature [ C] 0 to +40 Setting parameters Anchor size Minimum base material thickness h min [mm] 100 Spacing s min [mm] 100 Edge distance c min [mm] 100 c min s min c min s min h min 343