3.3 APPLICATION INTERIOR PAINTING

Transcription

1 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE G. Shop-Primed Steel Substrates: Clean field welds, bolted connections, and abraded areas of shop paint, and paint exposed areas with the same material as used for shop priming to comply with SSPC-PA 1 for touching up shop-primed surfaces. H. Galvanized-Metal Substrates: Remove grease and oil residue from galvanized sheet metal fabricated from coil stock by mechanical methods to produce clean, lightly etched surfaces that promote adhesion of subsequently applied paints. 3.3 APPLICATION A. Apply paints according to manufacturer's written instructions and to recommendations in "MPI Manual." 1. Use applicators and techniques suited for paint and substrate indicated. 2. Paint surfaces behind movable equipment and furniture same as similar exposed surfaces. Before final installation, paint surfaces behind permanently fixed equipment or furniture with prime coat only. 3. Paint front and backsides of access panels, removable or hinged covers, and similar hinged items to match exposed surfaces. 4. Do not paint over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates. 5. Primers specified in painting schedules may be omitted on items that are factory primed or factory finished if acceptable to topcoat manufacturers. B. Tint each undercoat a lighter shade to facilitate identification of each coat if multiple coats of same material are to be applied. Tint undercoats to match color of topcoat, but provide sufficient difference in shade of undercoats to distinguish each separate coat. C. If undercoats or other conditions show through topcoat, apply additional coats until cured film has a uniform paint finish, color, and appearance. D. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks. E. Painting Fire Suppression, Plumbing, HVAC, Electrical, Communication, and Electronic Safety and Security Work: 1. Paint the following work where exposed in equipment rooms: a. Equipment, including panelboards. b. Uninsulated metal piping. c. Uninsulated plastic piping. d. Pipe hangers and supports. e. Metal conduit. f. Plastic conduit. g. Tanks that do not have factory-applied final finishes. h. Duct, equipment, and pipe insulation having cotton or canvas insulation covering or other paintable jacket material. 2. Paint the following work where exposed in occupied spaces: a. Equipment, including panelboards. b. Uninsulated metal piping. INTERIOR PAINTING

2 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE c. Uninsulated plastic piping. d. Pipe hangers and supports. e. Metal conduit. f. Plastic conduit. g. Duct, equipment, and pipe insulation having cotton or canvas insulation covering or other paintable jacket material. h. Other items as directed by Architect. 3. Paint portions of internal surfaces of metal ducts, without liner, behind air inlets and outlets that are visible from occupied spaces. 3.4 CLEANING AND PROTECTION A. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from Project site. B. After completing paint application, clean spattered surfaces. Remove spattered paints by washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces. C. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and leave in an undamaged condition. D. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces. 3.5 INTERIOR PAINTING SCHEDULE A. Concrete Substrates, Nontraffic Surfaces: 1. Latex System: a. Prime Coat: Primer sealer, latex, interior, MPI #50. b. Prime Coat: Latex, interior, matching topcoat. c. Intermediate Coat: Latex, interior, matching topcoat. d. Topcoat: Latex, interior, flat, (Gloss Level 1), Beams, MPI #53. e. Topcoat: Latex, interior, (Gloss Level 3) Walls, Columns, MPI # Institutional Low-Odor/VOC Latex System: a. Prime Coat: Primer sealer, interior, institutional low odor/voc, MPI #149. b. Intermediate Coat: Latex, interior, institutional low odor/voc, matching topcoat. c. Topcoat: Latex, interior, institutional low odor/voc, flat (Gloss Level 1), MPI #143. d. Topcoat: Latex, interior, institutional low odor/voc, (Gloss Level 3), MPI #145. B. Concrete Substrates, Traffic Surfaces: 1. Water-Based Clear Sealer System: a. First Coat: Sealer, water based, for concrete floors, MPI #99. b. Topcoat: Sealer, water based, for concrete floors, MPI #99. C. CMU Substrates: 1. Latex System: a. Block Filler: Block filler, latex, interior/exterior, MPI #4]. b. Intermediate Coat: Latex, interior, matching topcoat. c. Topcoat: Latex, interior, flat, (Gloss Level 1), MPI #53. d. Topcoat: Latex, interior, (Gloss Level 3), MPI # Institutional Low-Odor/VOC Latex System: INTERIOR PAINTING

3 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE a. Block Filler: Block filler, latex, interior/exterior, MPI #4. b. Intermediate Coat: Latex, interior, institutional low odor/voc, matching topcoat. c. Topcoat: Latex, interior, institutional low odor/voc, flat (Gloss Level 1), MPI #143. d. Topcoat: Latex, interior, institutional low odor/voc, (Gloss Level 3), MPI #145. D. Steel Substrates: 1. Latex over Alkyd Primer System: a. Prime Coat: Primer, alkyd, anti-corrosive, for metal, MPI #79 or primer, alkyd, quick dry, for metal, MPI #76. b. Prime Coat: Shop primer specified in Section where substrate is specified. c. Intermediate Coat: Latex, interior, matching topcoat. d. Topcoat: Latex, interior, semi-gloss, (Gloss Level 5), MPI # Institutional Low-Odor/VOC Latex System: a. Prime Coat: Primer, rust-inhibitive, water based MPI #107. b. Intermediate Coat: Latex, interior, institutional low odor/voc, matching topcoat. c. Topcoat: Latex, interior, institutional low odor/voc, semi-gloss (Gloss Level 5), MPI #147. E. Galvanized-Metal Substrates: 1. Latex over Waterborne Primer System: a. Prime Coat: Primer, galvanized, water based, MPI #134]. b. Intermediate Coat: Latex, interior, matching topcoat. c. Topcoat: Latex, interior, semi-gloss, (Gloss Level 5), MPI # Institutional Low-Odor/VOC Latex System: a. Prime Coat: Primer, galvanized, water based, MPI #134. b. Intermediate Coat: Latex, interior, institutional low odor/voc, matching topcoat. c. Topcoat: Latex, interior, institutional low odor/voc, semi-gloss (Gloss Level 5), MPI #147. F. Gypsum Board Substrates: 1. Latex System: a. Prime Coat: Primer sealer, latex, interior, MPI #50. b. Prime Coat: Latex, interior, matching topcoat. c. Intermediate Coat: Latex, interior, matching topcoat. d. Topcoat: Latex, interior, flat, (Gloss Level 1), MPI #53. e. Topcoat: Latex, interior, (Gloss Level 3), MPI # Institutional Low-Odor/VOC Latex System: a. Prime Coat: Primer sealer, interior, institutional low odor/voc, MPI #149. b. Intermediate Coat: Latex, interior, institutional low odor/voc, matching topcoat. c. Topcoat: Latex, interior, institutional low odor/voc, flat (Gloss Level 1), MPI #143. d. Topcoat: Latex, interior, institutional low odor/voc, (Gloss Level 3), MPI #145.: 3. Chroma Key Paint System: a. Primer: Tough Prime. b. Topcoat: Chroma Key Paint. MPI #147. G. Wood Fiber and Primed Metal (Tectum): 1. Latex System MPI #226: a. Prime Coat: Primer sealer, latex, interior. b. Intermediate Coat: Latex, interior, matching topcoat. c. Topcoat: Latex, interior, semi-gloss, (Gloss Level 5). END OF SECTION INTERIOR PAINTING

4 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE SECTION HIGH-PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes surface preparation and application of high-performance coating systems on the following substrates: 1. Interior Substrates: a. Concrete, vertical surfaces. b. Concrete masonry units (CMU). c. Gypsum board. 1.3 DEFINITIONS A. Gloss Level 6: 70 to 85 units at 60 degrees, according to ASTM D 523. B. Gloss Level 7: More than 85 units at 60 degrees, according to ASTM D SUBMITTALS A. Product Data: For each type of product indicated. Include preparation requirements and application instructions. B. Samples for Verification: For each type of coating system and in each color and gloss of topcoat indicated. 1. Submit Samples on rigid backing, 8 inches (200 mm) square. 2. Step coats on Samples to show each coat required for system. 3. Label each coat of each Sample. C. Product List: For each product indicated, include the following: 1. Cross-reference to paint system and locations of application areas. Use same designations indicated on Drawings and in schedules. 2. Printout of current "MPI Approved Products List" for each product category specified in Part 2, with the proposed product highlighted. D. Furnish extra materials, from the same product run, that match products installed and that are packaged with protective covering for storage and identified with labels describing contents. 1. Coatings: 5 percent, but not less than 1 gal. (3.8 L) of each material and color applied. HIGH-PERFORMANCE COATINGS

5 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE 1.5 QUALITY ASSURANCE A. Mockups: Apply mockups of each coating system indicated to verify preliminary selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for materials and execution. 1. Architect will select one surface to represent surfaces and conditions for application of each coating system specified in Part 3. a. Wall Surfaces: Provide samples of at least 100 sq. ft. (9 sq. m). b. Other Items: Architect will designate items or areas required. 2. Final approval of color selections will be based on mockups. a. If preliminary color selections are not approved, apply additional mockups of additional colors selected by Architect at no added cost to Owner. 3. Approval of mockups does not constitute approval of deviations from the Contract Documents contained in mockups unless Architect specifically approves such deviations in writing. 4. Subject to compliance with requirements, approved mockups may become part of the completed Work if undisturbed at time of Material Completion. 1.6 DELIVERY, STORAGE, AND HANDLING A. Store materials not in use in tightly covered containers in well-ventilated areas with ambient temperatures continuously maintained at not less than 45 deg F (7 deg C). 1. Maintain containers in clean condition, free of foreign materials and residue. 2. Remove rags and waste from storage areas daily. 1.7 FIELD CONDITIONS A. Apply coatings only when temperature of surfaces to be coated and surrounding air temperatures are between 50 and 95 deg F (10 and 35 deg C). B. Do not apply coatings when relative humidity exceeds 85 percent; at temperatures less than 5 deg F (3 deg C) above the dew point; or to damp or wet surfaces. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. Benjamin Moore & Co. 2. Duron, Inc. 3. ICI Paints. 4. PPG Architectural Finishes, Inc. 5. Sherwin-Williams Company (The). 2.2 HIGH-PERFORMANCE COATINGS, GENERAL HIGH-PERFORMANCE COATINGS

6 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE A. MPI Standards: Provide products that comply with MPI standards indicated and are listed in "MPI Approved Products List." B. Material Compatibility: 1. Provide materials for use within each coating system that are compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience. 2. For each coat in a coating system, provide products recommended in writing by manufacturers of topcoat for use in coating system and on substrate indicated. 3. Provide products of same manufacturer for each coat in a coating system. C. Colors: Match Architect's samples. 2.3 BLOCK FILLERS A. Block Filler, Epoxy: MPI # EPOXY COATINGS A. Epoxy-Modified Latex, Interior, Gloss (Gloss Level 6) Kitchen, Gymnasium, Restrooms: MPI #115. B. Epoxy, High-Build, Low Gloss, Classrooms, Media Center, Corridors: MPI # SOURCE QUALITY CONTROL A. Testing of Coating Materials: Owner reserves the right to invoke the following procedure: 1. Owner will engage the services of a qualified testing agency to sample coating materials. Contractor will be notified in advance and may be present when samples are taken. If coating materials have already been delivered to Project site, samples may be taken at Project site. Samples will be identified, sealed, and certified by testing agency. 2. Testing agency will perform tests for compliance with product requirements. 3. Owner may direct Contractor to stop applying paints if test results show materials being used do not comply with product requirements. Contractor shall remove noncomplying coating materials from Project site, pay for testing, and recoat surfaces coated with rejected materials. Contractor will be required to remove rejected materials from previously coated surfaces if, on recoating with complying materials, the two coatings are incompatible. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates and conditions, with Applicator present, for compliance with requirements for maximum moisture content and other conditions affecting performance of the Work. 1. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows: a. Concrete: 12 percent. HIGH-PERFORMANCE COATINGS

7 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE b. Masonry (Clay and CMU): 12 percent. B. Verify suitability of substrates, including surface conditions and compatibility with existing finishes and primers. C. Proceed with coating application only after unsatisfactory conditions have been corrected. 1. Beginning coating application constitutes Contractor's acceptance of substrates and conditions. 3.2 PREPARATION A. Comply with manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual" applicable to substrates indicated. B. Remove hardware, covers, plates, and similar items already in place that are removable and are not to be painted. If removal is impractical or impossible because of size or weight of item, provide surface-applied protection before surface preparation and painting. 1. After completing painting operations, use workers skilled in the trades involved to reinstall items that were removed. Remove surface-applied protection. C. Clean substrates of substances that could impair bond of coatings, including dust, dirt, oil, grease, and incompatible paints and encapsulants. 1. Remove incompatible primers and reprime substrate with compatible primers or apply tie coat as required to produce coating systems indicated. D. Concrete Substrates: Remove release agents, curing compounds, efflorescence, and chalk. Do not coat surfaces if moisture content or alkalinity of surfaces to be coated exceeds that permitted in manufacturer's written instructions. 1. Clean surfaces with pressurized water. Use pressure range of 1500 to 4000 psi ( to kpa) at 6 to 12 inches (150 to 300 mm). 2. Abrasive blast clean surfaces to comply with SSPC-SP 7/NACE No. 4, "Brush-Off Blast Cleaning." E. Masonry Substrates: Remove efflorescence and chalk. Do not coat surfaces if moisture content or alkalinity of surfaces or if alkalinity of mortar joints exceed that permitted in manufacturer's written instructions. 1. Clean surfaces with pressurized water. Use pressure range of 1500 to 4000 psi ( to kpa) at 6 to 12 inches (150 to 300 mm). 3.3 APPLICATION A. Apply high-performance coatings according to manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual." 1. Use applicators and techniques suited for coating and substrate indicated. 2. Coat surfaces behind movable equipment and furniture same as similar exposed surfaces. Before final installation, coat surfaces behind permanently fixed equipment or furniture with prime coat only. 3. Coat back sides of access panels, removable or hinged covers, and similar hinged items to match exposed surfaces. HIGH-PERFORMANCE COATINGS

8 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE 4. Do not apply coatings over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates. B. Tint each undercoat a lighter shade to facilitate identification of each coat if multiple coats of the same material are to be applied. Tint undercoats to match color of finish coat, but provide sufficient difference in shade of undercoats to distinguish each separate coat. C. If undercoats or other conditions show through final coat, apply additional coats until cured film has a uniform coating finish, color, and appearance. D. Apply coatings to produce surface films without cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections. Produce sharp glass lines and color breaks. 3.4 FIELD QUALITY CONTROL A. Dry Film Thickness Testing: Owner will engage the services of a qualified testing and inspecting agency to inspect and test coatings for dry film thickness. 1. Contractor shall touch up and restore coated surfaces damaged by testing. 2. If test results show that dry film thickness of applied coating does not comply with coating manufacturer's written recommendations, Contractor shall pay for testing and apply additional coats as needed to provide dry film thickness that complies with coating manufacturer's written recommendations. 3.5 CLEANING AND PROTECTION A. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from Project site. B. After completing coating application, clean spattered surfaces. Remove spattered coatings by washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces. C. Protect work of other trades against damage from coating operation. Correct damage by cleaning, repairing, replacing, and recoating, as approved by Architect, and leave in an undamaged condition. D. At completion of construction activities of other trades, touch up and restore damaged or defaced coated surfaces. HIGH-PERFORMANCE COATINGS

9 NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE 3.6 INTERIOR HIGH-PERFORMANCE COATING SCHEDULE A. Concrete Substrates, Vertical Surfaces: 1. Epoxy System: a. Prime Coat: Epoxy, gloss, MPI #77. b. Intermediate Coat: Epoxy, gloss, MPI #77. c. Topcoat: Epoxy, gloss, MPI #77. B. CMU Substrates: 1. Epoxy System: a. Block Filler: Block filler, latex, interior/exterior, MPI #4. b. Block Filler: Block filler, epoxy, MPI #116. c. Intermediate Coat: Epoxy, gloss, MPI #77. d. Topcoat: Epoxy, gloss, MPI #77. C. Gypsum Board Substrates: 1. Epoxy System: a. Prime Coat: Primer sealer, latex, interior, MPI #50. b. Intermediate Coat: Epoxy, gloss, MPI #77. c. Topcoat: Epoxy, gloss, MPI #77. END OF SECTION HIGH-PERFORMANCE COATINGS

10 NORTH BRYAN COUNTY 3-5 SCHOOL PEMBROKE SECTION VISUAL DISPLAY SURFACES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Markerboards. 2. Tackboards. 3. Visual display rails. 1.3 SUBMITTALS A. Product Data: For each type of visual display board indicated. B. Shop Drawings: For each type of visual display board required. 1. Include dimensioned elevations. Show location of joints between individual panels where unit dimensions exceed maximum panel length. 2. Include sections of typical trim members. 3. Show anchors, grounds, reinforcement, accessories, layout, and installation details. C. Samples: Of the following products, showing color and texture or finish selected. Where finishes involve normal color and texture variations, include Sample sets showing the full range of variations expected. Prepare Samples from the same material to be used for the Work. 1. Visual Display Boards: Sample panels not less than 8-1/2 by 11 inches, mounted on the substrate indicated for the final Work. Include a panel for each type, color, and texture required. 2. Aluminum Trim and Accessories: Samples of each finish type and color, on 6-inch-long sections of extrusions and not less than 4-inch squares of sheet or plate. Where finishes involve normal color and texture variations, include sets showing the full range of variations expected. D. Product Certificates: Signed by manufacturers of tackboards certifying that vinyl-fabric-faced cork tackboard materials furnished comply with requirements specified for flame-spread ratings. 1.4 PROJECT CONDITIONS A. Field Measurements: Verify field measurements before preparation of Shop Drawings and before fabrication to ensure proper fitting. Coordinate fabrication schedule with construction progress to avoid delaying the Work. 1. Allow for trimming and fitting where taking field measurements before fabrication might delay the Work. 1.5 WARRANTY A. General Warranty: The special porcelain enamel markerboard warranty specified in this Article shall not deprive the Owner of other rights the Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by the Contractor under requirements of the Contract Documents. VISUAL DISPLAY SURFACES

11 NORTH BRYAN COUNTY 3-5 SCHOOL PEMBROKE B. Porcelain Enamel Markerboard Warranty: Submit a written warranty executed by manufacturer agreeing to replace porcelain enamel markerboards that do not retain their original writing and erasing qualities, become slick and shiny, or exhibit crazing, cracking, or flaking within the specified warranty period, provided the manufacturer's written instructions for handling, installation, protection, and maintenance have been followed. 1. Warranty Period: 50 years from date of Material Completion. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturer: Subject to compliance with requirements, provide products by one of the following: 1. Porcelain Enamel Markerboards and Tackboards. a. ABC School Equipment, a division of Platinum Visual Systems. b. ADP Lemco c. American Visual Display Products, a division of American Construction Specialties, LLC d. Claridge Products and Equipment e. Ghent Manufacturing f. Newline Products 2. Display Rail. a. Advantus Grip-a-Strip. b. Clip-it-Strip paper holder. c. Hold Up by Ghent. 2.2 MATERIALS A. Porcelain Enamel Markerboards: Balanced, high-pressure-laminated, porcelain enamel markerboards of 3-ply construction consisting of face sheet, core material, and backing. 1. Face Sheet: inch enameling grade steel especially processed for temperatures used in coating porcelain on steel. Coat exposed face and edges with a 3-coat process consisting of primer, ground coat, and color cover coat. Coat concealed face with a 2-coat process consisting of primer and ground coat. Fuse cover and ground coats to steel at manufacturer's standard firing temperatures, but not less than 1200 deg F. a. Cover Coat for Markerboards: Provide manufacturer's standard, white, special writing surface with gloss finish intended for use with erasable dry markers. 2. Core: 3/8-inch- thick, particleboard core material complying with requirements of ANSI A208.1, Grade 1-M Backing Sheet: inch- thick, aluminum-sheet backing. 4. Laminating Adhesive: Manufacturer's standard, moisture-resistant, thermoplastic-type adhesive. B. Plastic-Impregnated Cork Tackboards: Seamless sheet, 1/4-inch- thick, ground natural cork compressed with a resinous binder with washable vinyl finish and integral color throughout, laminated to burlap backing. Provide color and texture as scheduled or as selected by the Architect from manufacturer's standards. C. Extruded Aluminum: ASTM B 221, Alloy VISUAL DISPLAY SURFACES

12 NORTH BRYAN COUNTY 3-5 SCHOOL PEMBROKE 2.3 ACCESSORIES A. Metal Trim and Accessories: Fabricate frames and trim of not less than inch- thick, extruded-aluminum alloy, to suit type of installation. Provide straight, single-length units. Keep joints to a minimum. Miter corners to a neat, hairline closure. 1. Markertray: Manufacturer's standard, continuous, box-type, aluminum tray with slanted front and cast-aluminum end closures for each markerboard. 2. Map Rail: Furnish map rail at top of each markerboard unit, complete with the following accessories: 2.4 FABRICATION a. Display Rail: Provide continuous cork display rail approximately 1 or 2 inches wide, integral with map rail. b. End Stops: Provide one end stop at each end of map rail. c. Map Hooks: Provide 2 map hooks for every 48 inches of map rail or fraction thereof. d. Flag Holder: Provide one flag holder for each room. A. Porcelain Enamel Markerboards: Laminate facing sheet and backing sheet to core material under pressure with manufacturer's recommended flexible, waterproof adhesive. B. Assembly: Provide factory-assembled markerboard and tackboard units, unless field-assembled units are required. C. Tackable Display Surface: 2.5 FINISHES 1. Make joints only where total length exceeds maximum manufactured length. Fabricate with minimum number of joints, balanced around center of board, as acceptable to Architect. 2. Provide manufacturer's standard vertical joint system between abutting sections of markerboards. 3. Provide manufacturer's standard mullion trim at joints between markerboards and tackboards. 4. Fabrication: Fabricate panels to sizes and configurations indicated; attach facing materials to cores to produce installed panels with visible surfaces fully covered and free from waves in fabric weave, wrinkles, sags, blisters, seams, adhesive, or other foreign matter. a. Fabricate back-mounted panels to exact sizes required to fit back of display cases, based on field measurements of completed substrates indicated to receive acoustical wall panels. b. Where square corners are indicated, tailor corners. c. Where fabrics with directional or repeating patterns, or directional weave, are indicated, mark fabric top and attach fabric in same direction. d. Where fabric facings with seams are indicated, fabricate invisible seams and comply with Shop Drawings for location. A. General: Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations relative to applying and designating finishes. B. Finish designations prefixed by AA conform to the system established by the Aluminum Association for designating aluminum finishes. C. Class II, Clear Anodic Finish: AA-M12C22A31 (Mechanical Finish: nonspecular as fabricated; Chemical Finish: etched, medium matte; Anodic Coating: Architectural Class II, clear coating mm or thicker) complying with AAMA VISUAL DISPLAY SURFACES

13 NORTH BRYAN COUNTY 3-5 SCHOOL PEMBROKE PART 3 - EXECUTION 3.1 EXAMINATION A. Examine wall surfaces, with Installer present, for compliance with requirements and other conditions affecting installation of visual display boards. 1. Surfaces to receive markerboards shall be free of dirt, scaling paint, and projections or depressions that would affect smooth, finished surfaces of markerboards. 2. Surfaces to receive tackboards shall be dry and free of substances that would impair the bond between tackboards and substrate. 3. Do not proceed with installation until unsatisfactory conditions have been corrected. 3.2 INSTALLATION A. Deliver factory-built visual display boards completely assembled in one piece without joints, where possible. If dimensions exceed panel size, provide 2 or more pieces of equal length as acceptable to Architect. When overall dimensions require delivery in separate units, prefit components at the factory, disassemble for delivery, and make final joints at the site. Use splines at joints to maintain surface alignment. B. Install units in locations and at mounting heights indicated and according to manufacturer's written instructions. Keep perimeter lines straight, plumb, and level. Provide grounds, clips, backing materials, adhesives, brackets, anchors, trim, and accessories necessary for complete installation. 3.3 ADJUSTING AND CLEANING A. Verify that accessories required for each unit have been properly installed and that operating units function properly. B. Clean units according to manufacturer's written instructions. END OF SECTION VISUAL DISPLAY SURFACES

14 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SECTION SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section include the following: 1. Panel Signs. SUMMARY OF SIGN TYPES FOR BOTH McALLISTER AND PEMBROKE ELEMENTARY SCHOOLS Abbrev Name See Diagram Notes A Accessible Unisex A Include HC access symbol DG Dimensional Graphics DG Cast Aluminum Letters DR Directional Signage DR M Men (Boys) M Include HC access symbol W Women (Girls) W Include HC access symbol NA No Admittance NA Locate center of door PD Pedestrian Directional Signage PD R1 Room sign number only R1 R2 Room sign with insert window R2 panel (for personnel name) R3 Room sign with permanent name and number panels R3 Lower panel to be fabricated with clear window to accept personnel name insert EP Evacuation Plan EP 1.3 DEFINITIONS A. ADA-ABA Accessibility Guidelines: U.S. Architectural & Transportation Barriers Compliance Board's "Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines." 1.4 SUBMITTALS A. Product Data: For each type of product indicated. B. Shop Drawings: Show fabrication and installation details for signs. 1. Show sign mounting heights, locations of supplementary supports to be provided by others, and accessories. SIGNAGE

15 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) 2. Provide message list, typestyles, and graphic elements, including tactile characters and Braille, and layout for each sign. C. Samples for Initial Selection: Manufacturer's color charts consisting of actual units or sections of units showing the full range of colors available for the following: 1. Acrylic sheet. D. Samples for Verification: For each of the following products and for the full range of color, texture, and sign material indicated, of sizes indicated: 1. Acrylic Sheet: 4 by 4 inches (100 by 100 mm) for each color required. E. Sign Schedule: Use same designations indicated on Drawings. F. Qualification Data: For Installer and fabricator. G. Maintenance Data: For signs to include in maintenance manuals. H. Warranty: Special warranty specified in this Section. 1.5 QUALITY ASSURANCE A. Installer Qualifications: An employer of workers trained and approved by manufacturer. B. Fabricator Qualifications: Shop that employs skilled workers who custom-fabricate products similar to those required for this Project and whose products have a record of successful inservice performance. C. Source Limitations for Signs: Obtain each sign type indicated from one source from a single manufacturer. D. Regulatory Requirements: Comply with applicable provisions in ADA-ABA Accessibility Guidelines. 1.6 PROJECT CONDITIONS A. Field Measurements: Verify recess openings by field measurements before fabrication and indicate measurements on Shop Drawings. 1.7 COORDINATION A. Coordinate placement of anchorage devices with templates for installing signs. 1.8 WARRANTY A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of signs that fail in materials or workmanship within specified warranty period. 1. Warranty Period: Five years from date of Material Completion. PART 2 - PRODUCTS 2.1 MATERIALS A. Acrylic Sheet: ASTM D 4802, Category A-1 (cell-cast sheet), Type UVA (UV absorbing). SIGNAGE

16 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) 2.2 PANEL SIGNS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. APCO Graphics, Inc. 2. ASI-Modulex, Inc. 3. Best Sign Systems Inc. 4. Innerface Sign Systems, Inc. 5. InPro Corporation. 6. Mohawk Sign Systems. B. Interior Panel Signs: Provide smooth sign panel surfaces constructed to remain flat under installed conditions within a tolerance of plus or minus 1/16 inch (1.5 mm) measured diagonally from corner to corner, complying with the following requirements: 1. Acrylic Sheet: inch (2.03 mm) thick. 2. Edge Condition: Square cut. 3. Corner Condition: Square. 4. Mounting: Framed. a. Wall mounted with concealed anchors. b. Manufacturer's standard anchors for substrates encountered. c. Provide blank backing 5. Color: As selected by Architect from manufacturer's full range. 6. Tactile Characters: Characters and Grade 2 Braille raised 1/32 inch (0.8 mm) above surface with contrasting colors. C. Panel Sign Frames: 1. PVC Frames: Extruded, high-impact PVC plastic. a. Color: As selected by Architect from manufacturer's full range. b. Depth: As indicated. c. Profile: Square. d. Corner Condition: Square. D. Changeable Message Inserts: Fabricate signs to allow insertion of changeable messages in the form of transparent covers with paper inserts printed by Owner. 1. Furnish insert material and software for creating text and symbols for PC-Windows computers for Owner production of paper inserts. E. Tactile and Braille Sign: Manufacturer's standard process for producing text and symbols complying with ADA-ABA Accessibility Guidelines and with ICC/ANSI A Text shall be accompanied by Grade 2 Braille. Produce precisely formed characters with square-cut edges free from burrs and cut marks; Braille dots with domed or rounded shape. 1. Panel Material: Clear acrylic sheet with opaque color coating, subsurface applied. 2. Raised-Copy Thickness: Not less than 1/32 inch (0.8 mm). F. Subsurface Copy: Apply minimum 4-mil- (0.10-mm-) thick vinyl copy to back face of clear acrylic sheet forming panel face to produce precisely formed opaque image. Image shall be free of rough edges. G. Colored Coatings for Acrylic Sheet: For copy, background and frame colors, provide colored coatings, including inks, dyes, and paints, that are recommended by acrylic manufacturers for optimum adherence to acrylic surface and are UV and water resistant for five years for application intended. 1. Color: As selected by Architect from manufacturer's full range. SIGNAGE

17 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Panel Sign Schedule McALLISTER ELEMENTARY SCHOOL: SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 1 R3 A102 (Additional Name Insert) A102 CLASSROOM 2 R3 A104 (Additional Name Insert) A104 CLASSROOM 3 R3 A105 (Additional Name Insert) A105 CLASSROOM 4 R3 A106 (Additional Name Insert) A106 CLASSROOM 5 R3 A107 (Additional Name Insert) A107 CLASSROOM 6 R3 A108 (Additional Name Insert) A108 CLASSROOM 7 R3 A109 (Additional Name Insert) A109 CLASSROOM 8 R3 A110 (Additional Name Insert) A110 CLASSROOM 9 R3 A111 (Additional Name Insert) A111 CLASSROOM 10 R3 A114 (Additional Name Insert) A114 WAITING 11 R3 A115 (Additional Name Insert) A115 CONFERENCE ROOM 12 R3 A116 (Additional Name Insert) A116 OFFICE 13 R2 A117 ELECTRICAL ROOM A117 ELECTICAL 14 R3 A118 (Additional Name Insert) A118 OFFICE 15 A RESTROOM A119 TOILET 16 R2 A120 DATA A120 DATA 17 A RESTROOM A121 TOILET 18 R3 A122 (Additional Name Insert) A122 WORKROOM 19 R1 A123 A123 JANITOR 20 R1 A124 A124 STORAGE 21 W GIRLS A125 GIRLS 22 NA NO ADMITTANCE A126 CHASE 23 M BOYS A127 BOYS 24 R3 A128 (Additional Name Insert) A128 CLASSROOM 25 R3 A129 (Additional Name Insert) A129 CLASSROOM 26 R3 A130 (Additional Name Insert) A130 CLASSROOM 27 R3 A131 (Additional Name Insert) A131 CLASSROOM 28 R3 A132 (Additional Name Insert) A132 CLASSROOM 29 R3 A133 (Additional Name Insert) A133 CLASSROOM 30 R3 A134 (Additional Name Insert) A134 CLASSROOM 31 R3 A135 (Additional Name Insert) A135 CLASSROOM 32 R3 A136 (Additional Name Insert) A136 CLASSROOM 33 R3 A137 (Additional Name Insert) A137 CLASSROOM 34 DG GYMNASIUM B101 GYMNASIUM Mount on Gypsum Bd. Soffit Bulkhead 35 R1 B102 B102 STORAGE 36 R1 B103 B103 STORAGE 37 R1 B104 B104 STORAGE SIGNAGE

18 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 38 R2 B105 CONCESSIONS B105 CONCESSIONS 39 R3 B106 (Additional Name Insert) B106 OFFICE 40 DR A102 - A NA NO ADMITTANCE B107 MECHANICAL 42 R1 B110 B110 STORAGE 43 R1 B111 B111 JANITOR 44 R3 B112 (Additional Name Insert) B112 CLASSROOM 45 M MEN B114 MEN 46 NA NO ADMITTANCE B115 CHASE 47 W WOMEN B116 WOMEN 48 R2 B117 DATA B117 DATA 49 R1 B118 B118 STORAGE 50 DR ART & MUSIC COMPUTER SCIENCE B R3 B154 (Additional Name Insert) B154 COMPUTER SCIENCE Provide 2 52 R2 B155 KILN B155 KILN 53 R3 B156 (Additional Name Insert) B156 ART 54 R1 B157 B157 STORAGE 55 R3 B158 (Additional Name Insert) B158 MUSIC Provide 2 56 NA NO ADMITTANCE B159 STAIR 57 R1 B161 B161 STORAGE Provide 2 58 R3 B162 (Additional Name Insert) B162 MUSIC 59 R2 C101 ELECTRICAL C101 ELECTRICAL 60 R2 C102 MAIN OFFICE C102 RECEPTION Provide 2 Mount 1 on glass 61 R3 C103 (Additional Name Insert) C103 CLERICAL 62 DR GYMNASIUM WING A ART & MUSIC MEDIA CENTER 63 R3 C105 (Additional Name Insert) C105 PRINCIPAL 64 R3 C106 C106 WORKROOM 65 R1 C107 C107 MAIL 66 R2 C108 RECORDS C108 RECORDS 67 R3 C109 (Additional Name Insert) C109 OFFICE 68 R1 C110 C110 SUPPLY 69 R3 C111 (Additional Name Insert) C111 OFFICE 70 R3 C112 (Additional Name Insert) C112 TESTING 71 R3 C113 (Additional Name Insert) C113 OFFICE SIGNAGE

19 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 72 A RESTROOM C114 TOILET 73 R3 C115 (Additional Name Insert) C115 CONFERENCE ROOM 74 R1 C116 C116 JANITOR 75 R3 C117 (Additional Name Insert) C117 COMPUTER LAB Provide 2 76 A RESTROOM C118 TOILET 77 R2 C119 NURSE C119 NURSE 78 A RESTROOM C119B TOILET 79 NA NO ADMITTANCE C121 MEZZANINE ACCESS 80 DG MEDIA CENTER C130 MEDIA CENTER Mount on Gypsum Bd. Soffit Bulkhead 81 R3 C131 (Additional Name Insert) C131 COMPUTER LAB Provide 2 Mount 1 on glass 82 R3 C132 (Additional Name Insert) C132 OFFICE 83 R3 C133 (Additional Name Insert) C133 OFFICE 84 R2 C134 DATA C134 DATA 85 R1 C135 C135 STORAGE 86 A RESTROOM C138 TOILET 87 R3 C139 (Additional Name Insert) C139 OFFICE Mount on Glass 88 R1 C140 C140 STORAGE 89 R3 C141 (Additional Name Insert) C141 MULTI-MEDIA Mount on Glass 90 R3 C142 (Additional Name Insert) C142 BROADCAST Mount on Glass 91 R3 C143 (Additional Name Insert) C143 LRG GRP WRKRM Mount on Glass 92 DR E101 E R2 D100 MULTI-PURPOSE ROOM D100 MULTI-PURPOSE ROOM Provide 2 94 DG D102 CAFETERIA D102 CAFETERIA Provide 2 95 R1 D103 D103 STORAGE 96 R2 D104 DATA D104 DATA 97 R1 D105 D105 STORAGE 98 NA NO ADMITTANCE D106 MECHANICAL 99 R1 D107 D107 STORAGE 100 DR CAFETERIA WING E WING F 101 R1 D113 D113 STORAGE 102 R1 D114 D114 JANITOR 103 A RESTROOM D115 TOILET 104 R1 D116 D116 LOCKERS 105 A RESTROOM D117 TOILET 106 R1 D118 D118 JANITOR 107 R1 D119 D119 CHEMICALS SIGNAGE

20 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 108 R1 D120 D120 DRY STORAGE 109 NOT USED 110 NOT USED 111 R3 D129 (Additional Name Insert) D129 OFFICE Mount on Glass 112 DR F102 F M BOYS D140 BOYS 114 NA NO ADMITTANCE D141 CHASE 115 W GIRLS D142 GIRLS 116 R1 D144 D144 RECEIVING 117 M MEN D152 VISITORS TOILET 118 W WOMEN D153 VISITPRS TOILET 119 NA NO ADMITTANCE D154 SUPPLY 120 R2 E101 ELECTRICAL E101 ELECTRICAL 121 R1 E103 E103 STORAGE 122 M BOYS E104 BOYS 123 NA NO ADMITTANCE E105 CHASE 124 W GIRLS E106 GIRLS 125 R3 E107 (Additional Name Insert) E107 ECS CLASSROOM 126 R3 E108 (Additional Name Insert) E108 ECS CLASSROOM 127 A RESTROOM E109 TOILET 128 A RESTROOM E110 TOILET 129 NA NO ADMITTANCE E100A WATER HEATER Provide NOT USED 131 A RESTROOM E113 TOILET 132 A RESTROOM E114 TOILET 133 NOT USED 134 NOT USED 135 R3 E118 (Additional Name Insert) E118 ECS CLASSROOM 136 R3 E119 (Additional Name Insert) E119 ECS CLASSROOM 137 R3 E120 (Additional Name Insert) E120 CLASSROOM 138 R3 E121 (Additional Name Insert) E121 CLASSROOM 139 R3 E122 (Additional Name Insert) E122 CLASSROOM 140 R3 E123 (Additional Name Insert) E123 CLASSROOM 141 R3 E124 (Additional Name Insert) E124 OFFICE 142 R3 E125 (Additional Name Insert) E125 CONFERENCE ROOM 143 R3 E126 (Additional Name Insert) E126 OFFICE 144 R1 E127 E127 JANITOR 145 R3 E128 E128 WAITING 146 A RESTROOM E129 TOILET SIGNAGE

21 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 147 R2 E130 DATA E130 DATA 148 A RESTROOM E131 TOILET 149 R3 E132 (Additional Name Insert) E132 WORKROOM 150 R2 E133 ELECTRICAL ROOM E133 ELECTRICAL 151 R1 E134 E134 STORAGE 152 W GIRLS E135 GIRLS 153 NA NO ADMITTANCE E137 CHASE 154 M BOYS E139 BOYS 155 R3 E140 (Additional Name Insert) E140 CLASSROOM 156 R3 E141 (Additional Name Insert) E141 CLASSROOM 157 R3 E142 (Additional Name Insert) E142 CLASSROOM 158 R3 E143 (Additional Name Insert) E143 CLASSROOM 159 R3 E144 (Additional Name Insert) E144 CLASSROOM 160 R3 E145 (Additional Name Insert) E145 CLASSROOM 161 R3 E146 (Additional Name Insert) E146 CLASSROOM 162 R3 E147 (Additional Name Insert) E147 CLASSROOM 163 R3 E148 (Additional Name Insert) E148 CLASSROOM 164 R3 E149 (Additional Name Insert) E149 CLASSROOM 165 R3 E150 (Additional Name Insert) E150 CLASSROOM 166 R3 E151 (Additional Name Insert) E151 CLASSROOM 167 R3 E152 (Additional Name Insert) E152 CLASSROOM 168 R3 E153 (Additional Name Insert) E153 CLASSROOM 169 R1 F102 F102 BOOK STORAGE 170 R1 F103 F103 STORAGE 171 R3 F104 (Additional Name Insert) F104 CLASSROOM 172 R3 F105 (Additional Name Insert) F105 CLASSROOM 173 R3 F106 (Additional Name Insert) F106 CLASSROOM 174 R3 F107 (Additional Name Insert) F107 CLASSROOM 175 R3 F108 (Additional Name Insert) F108 KINDERGARTEN CR 176 R3 F109 (Additional Name Insert) F109 KINDERGARTEN CR 177 W GIRLS F110 TOILET 178 M BOYS F111 TOILET 179 A RESTROOM F112 VESTIBULE Provide A RESTROOM F113 VESTIBULE Provide M BOYS F114 TOILET 182 W GIRLS F115 TOILET 183 R3 F116 (Additional Name Insert) F116 KINDERGARTEN CR 184 R3 F117 (Additional Name Insert) F117 KINDERGARTEN CR 185 R3 F118 (Additional Name Insert) F118 WAITING SIGNAGE

22 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 186 R3 F119 (Additional Name Insert) F119 CONFERENCE ROOM 187 R3 F120 (Additional Name Insert) F120 OFFICE 188 R1 F121 F121 JANITOR 189 R3 F122 (Additional Name Insert) F122 OFFICE 190 A RESTROOM F123 TOILET 191 R2 F124 DATA F124 DATA 192 A RESTROOM F125 TOILET 193 R3 F126 (Additional Name Insert) F126 WORKROOM 194 R2 F127 ELECTRICAL ROOM F127 ELECTRICAL 195 R3 F128 (Additional Name Insert) F128 KINDERGARTEN CR 196 R1 F129 F129 STORAGE 197 M F130 BOYS F130 TOILET 198 R3 F131 (Additional Name Insert) F131 KINDERGARTEN CR 199 A RESTROOM F132 VESTIBULE Provide M BOYS F133 TOILET 201 W GIRLS F134 TOILET 202 A RESTROOM F135 VESTTIBULE Provide R3 F136 (Additional Name Insert) F136 KINDERGARTEN CR 204 W GIRLS F137 TOILET 205 R3 F138 (Additional Name Insert) F138 KINDERGARTEN CR 206 R3 F139 (Additional Name Insert) F139 KINDERGARTEN CR 207 M BOYS F140 TOILET 208 R3 F141 (Additional Name Insert) F141 KINDERGARTEN CR 209 A RESTROOM F142 VESTIBULE Provide M BOYS F143 TOILET 211 W GIRLS F144 TOILET 212 A RESTROOM F145 VESTIBULE Provide R3 F146 (Additional Name Insert) F146 KINDERGARTEN CR 214 W GIRLS F147 TOILET 215 R3 F149 (Additional Name Insert) F149 KINDERGARTEN CR 216 PD GYMNASIUM 217 PD GYMNASIUM 218 PD MAIN OFFICE 219 PD MAIN OFFICE 220 PD MAIN OFFICE 221 PD MAIN OFFICE SIGNAGE

23 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (McALLISTER) NOTES 222 ED Locations to be determined Provide 16 Panel Sign Schedule NEW BRYAN COUNTY ELEMENTARY SCHOOL: SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (N. BRYAN) NOTES 1 R3 A102 (Additional Name Insert) A102 CLASSROOM 2 R3 A104 (Additional Name Insert) A104 CLASSROOM 3 R3 A105 (Additional Name Insert) A105 CLASSROOM 4 R3 A106 (Additional Name Insert) A106 CLASSROOM 5 R3 A107 (Additional Name Insert) A107 CLASSROOM 6 R3 A108 (Additional Name Insert) A108 CLASSROOM 7 R3 A109 (Additional Name Insert) A109 CLASSROOM 8 R3 A110 (Additional Name Insert) A110 CLASSROOM 9 R3 A111 (Additional Name Insert) A111 CLASSROOM 10 R3 A115 (Additional Name Insert) A115 CONFERENCE ROOM 11 R3 A116 (Additional Name Insert) A116 OFFICE 12 R2 A117 ELECTRICAL ROOM A117 ELECTICAL 13 R3 A118 (Additional Name Insert) A118 CLASSROOM 14 A RESTROOM A119 TOILET 15 R2 A120 DATA A120 DATA 16 A RESTROOM A121 TOILET 17 R3 A122 (Additional Name Insert) A122 WORKROOM 18 R1 A123 A123 JANITOR 19 R1 A124 A124 STORAGE 20 W GIRLS A125 GIRLS 21 NA NO ADMITTANCE A126 CHASE 22 M BOYS A127 BOYS 23 R3 A128 (Additional Name Insert) A128 CLASSROOM 24 R3 A129 (Additional Name Insert) A129 CLASSROOM 25 R3 A130 (Additional Name Insert) A130 CLASSROOM 26 R3 A131 (Additional Name Insert) A131 CLASSROOM 27 R3 A132 (Additional Name Insert) A132 CLASSROOM 28 R3 A133 (Additional Name Insert) A133 CLASSROOM 29 R3 A134 (Additional Name Insert) A134 CLASSROOM 30 R3 A135 (Additional Name Insert) A135 CLASSROOM 31 DG GYMNASIUM B101 GYMNASIUM Mount on Gypsum Bd. Soffit Bulkhead 32 R1 B102 B102 STORAGE 33 R1 B103 B103 STORAGE 34 R1 B104 B104 STORAGE SIGNAGE

24 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (N. BRYAN) NOTES 35 R2 B105 CONCESSIONS B105 CONCESSIONS 36 R3 B106 (Additional Name Insert) B106 OFFICE 37 NA NO ADMITTANCE B107 MECHANICAL 38 DR MUSIC & ART COMPUTER SCIENCE B154 B DR A102 A R1 B110 B110 STORAGE 41 R1 B111 B111 JANITOR 42 R3 B112 (Additional Name Insert) B112 CLASSROOM 43 M MEN B114 MEN 44 NA NO ADMITTANCE B115 CHASE 45 W WOMEN B116 WOMEN 46 R2 B117 DATA B117 DATA 47 R1 B118 B118 STORAGE 48 R3 B154 (Additional Name Insert) B154 COMPUTER SCIENCE Provide 2 49 R2 B155 KILN B155 KILN 50 R3 B156 (Additional Name Insert) B156 ART 51 R1 B157 B157 STORAGE 52 R3 B158 (Additional Name Insert) B158 MUSIC Provide 2 53 NA NO ADMITTANCE B159 STAIR 54 R2 B161 B161 STORAGE Provide 2 55 R3 B162 (Additional Name Insert) B162 MUSIC 56 DR GYMNASIUM WING A ART & MUSIC MEDIA CENTER 57 R2 C101 ELECTRICAL ROOM C101 ELECTRICAL 58 R2 C102 MAIN OFFICE C102 RECEPTION Provide 2 Mount on glass 59 R3 C103 (Additional Name Insert) C103 CLERICAL 60 DR CAFETERIA WING E 61 R3 C105 (Additional Name Insert) C105 PRINCIPAL 62 R3 C106 C106 WORKROOM 63 R1 C107 C107 MAIL 64 R2 C108 RECORDS C108 RECORDS 65 R3 C109 (Additional Name Insert) C109 OFFICE 66 R1 C110 C110 SUPPLY SIGNAGE

25 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (N. BRYAN) NOTES 67 R3 C111 (Additional Name Insert) C111 OFFICE 68 R3 C112 (Additional Name Insert) C112 TESTING 69 R3 C113 (Additional Name Insert) C113 OFFICE 70 A C114 RESTROOM C114 TOILET 71 R3 C115 (Additional Name Insert) C115 CONFERENCE ROOM 72 R1 C116 C116 JANITOR 73 R3 C117 (Additional Name Insert) C117 COMPUTER LAB Provide 2 74 A RESTROOM C118 TOILET 75 R2 C119 NURSE C119 NURSE 76 A RESTROOM C119B TOILET 77 NA NO ADMITTANCE C121 MEZZANINE ACCESS 78 DG MEDIA CENTER C130 MEDIA CENTER Mount on Gypsum Bd. Soffit Bulkhead 79 R3 C131 (Additional Name Insert) C131 COMPUTER LAB Provide 2 Mount 1 on Glass 80 R3 C132 (Additional Name Insert) C132 OFFICE 81 R3 C133 (Additional Name Insert) C133 OFFICE 82 R2 C134 DATA C134 DATA 83 R1 C135 C135 STORAGE 84 A RESTROOM C138 TOILET 85 R3 C139 (Additional Name Insert) C139 OFFICE Mount on Glass 86 R1 C140 C140 STORAGE 87 R3 C141 (Additional Name Insert) C141 MULTI-MEDIA Mount on Glass 88 R3 C142 (Additional Name Insert) C142 BROADCAST Mount on Glass 89 R3 C143 (Additional Name Insert) C143 LRG GRP WRKRM Mount on Glass NOT USED 91 R2 D100 MULTI-PURPOSE ROOM D100 MULTI-PURPOSE ROOM Provide 2 92 DG CAFETERIA D102 CAFETERIA 93 R1 D103 D103 STORAGE 94 R2 D104 DATA D104 DATA 95 R1 D105 D105 STORAGE 96 NA NO ADMITTANCE D106 MECHANICAL 97 R1 D107 D107 STORAGE 98 NOT USED 99 R1 D113 D113 STORAGE 100 R1 D114 D114 JANITOR 101 A RESTROOM D115 TOILET 102 R1 D116 D116 LOCKERS 103 A RESTROOM D117 TOILET SIGNAGE

26 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (N. BRYAN) NOTES 104 R1 D118 D118 JANITOR 105 R1 D119 D119 CHEMICALS 106 R1 D120 D120 DRY STORAGE 107 NOT USED 108 DR E103 E R3 D129 (Additional Name Insert) D129 OFFICE Mount on Glass 110 NOT USED 111 M BOYS D140 BOYS 112 NA NO ADMITTANCE D141 CHASE 113 W GIRLS D142 GIRLS 114 R1 D144 D144 RECEIVING 115 M MEN D152 VISITORS TOILET 116 W WOMEN D153 VISITPRS TOILET 117 R1 D154 D154 SUPPLY 118 R2 E101 ELECTRICAL E101 ELECTRICAL 119 R1 E103 E103 STORAGE 120 M BOYS E104 BOYS 121 NA NO ADMITTANCE E105 CHASE 122 W GIRLS E106 GIRLS 123 R3 E107 (Additional Name Insert) E107 ECS CLASSROOM 124 R3 E108 (Additional Name Insert) E108 ECS CLASSROOM 125 A RESTROOM E109 TOILET 126 A RESTROOM E110 TOILET 127 NA NO ADMITTANCE E100A WATER HEATER 128 NOT USED 129 A RESTROOM E113 TOILET 130 A RESTROOM E114 TOILET 131 R1 NOT USED 132 NOT USED 133 E118 (Additional Name Insert) E118 ECS CLASSROOM 134 R3 E119 (Additional Name Insert) E119 ECS CLASSROOM 135 R3 E120 (Additional Name Insert) E120 CLASSROOM 136 R3 E121 (Additional Name Insert) E121 CLASSROOM 137 R3 E122 (Additional Name Insert) E122 CLASSROOM 138 R3 E123 (Additional Name Insert) E123 CLASSROOM 139 R3 E124 (Additional Name Insert) E124 OFFICE 140 R3 E125 (Additional Name Insert) E125 CONFERENCE ROOM 141 R3 E126 (Additional Name Insert) E126 CLASSROOM 142 R1 E127 E127 JANITOR SIGNAGE

27 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) SIGN# TYPE MESSAGE (Number & Text) SPACE/AREA (N. BRYAN) NOTES 143 A RESTROOM E129 TOILET 144 R2 E130 DATA E130 DATA 145 A RESTROOM E131 TOILET 146 R3 E132 (Additional Name Insert) E132 WORKROOM 147 R2 E133 ELECTRICAL E133 ELECTRICAL 148 R1 E134 STORAGE E134 STORAGE 149 W GIRLS E135 GIRLS 150 NA NO ADMITTANCE E137 CHASE 151 M E139 BOYS E139 BOYS 152 R3 E140 (Additional Name Insert) E140 CLASSROOM 153 R3 E141 (Additional Name Insert) E141 CLASSROOM 154 R3 E142 (Additional Name Insert) E142 CLASSROOM 155 R3 E143 (Additional Name Insert) E143 CLASSROOM 156 R3 E144 (Additional Name Insert) E144 CLASSROOM 157 R3 E145 (Additional Name Insert) E145 CLASSROOM 158 R3 E146 (Additional Name Insert) E146 CLASSROOM 159 R3 E147 (Additional Name Insert) E147 CLASSROOM 160 R1 F102 F102 BOOK STORAGE 161 R1 F103 F103 STORAGE 162 PD GYMNASIUM 163 PD GYMNASIUM 164 PD MAIN OFFICE 165 PD MAIN OFFICE 166 PD MAIN OFFICE 167 PD MAIN OFFICE 168 ED Locations to be determined Provide ACCESSORIES A. Anchors and Inserts: Provide nonferrous-metal or hot-dip galvanized anchors and inserts for exterior installations and elsewhere as required for corrosion resistance. Use toothed steel or lead expansion-bolt devices for drilled-in-place anchors. Furnish inserts, as required, to be set into concrete or masonry work. SIGNAGE

28 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) 2.4 FINISHES, GENERAL A. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. B. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. 2.5 ACRYLIC SHEET FINISHES A. Colored Coatings for Acrylic Sheet: For copy, background and frame colors, provide colored coatings, including inks, dyes, and paints, that are recommended by acrylic manufacturers for optimum adherence to acrylic surface and that are UV and water resistant for five years for application intended. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of work. B. Verify that items including anchor inserts are sized and located to accommodate signs. C. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 INSTALLATION A. Locate signs and accessories where indicated, using mounting methods of types described and complying with manufacturer's written instructions. 1. Install signs level, plumb, and at heights indicated, with sign surfaces free of distortion and other defects in appearance. 2. Interior Wall Signs: Install signs on walls adjacent to latch side of door where applicable. Where not indicated or possible, such as double doors, install signs on nearest adjacent walls. Locate to allow approach within 3 inches (75 mm) of sign without encountering protruding objects or standing within swing of door. B. Wall-Mounted Signs: Comply with sign manufacturer's written instructions except where more stringent requirements apply. 1. Silicone-Adhesive Mounting: Attach signs to irregular, porous, or vinyl-covered surfaces. 2. Shim Plate Mounting: Provide 1/8-inch- (3-mm-) thick, concealed aluminum shim plates with predrilled and countersunk holes, at locations indicated, and where other mounting methods are not practicable. Attach plate with fasteners and anchors suitable for secure attachment to substrate. Attach panel signs to plate using method specified above. 3. Mechanical Fasteners: Use nonremovable mechanical fasteners placed through predrilled holes. Attach signs with fasteners and anchors suitable for secure attachment to substrate as recommended in writing by sign manufacturer. 4. Signs Mounted on Glass: Provide matching opaque plate on opposite side of glass to conceal mounting materials. SIGNAGE

29 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) 3.3 CLEANING AND PROTECTION A. After installation, clean soiled sign surfaces according to manufacturer's written instructions. Protect signs from damage until acceptance by Owner. SIGNAGE

30 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) B. SIGNAGE DRAWINGS Sign Type A SIGNAGE

31 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type M SIGNAGE

32 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type W SIGNAGE

33 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type NA SIGNAGE

34 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type R1 SIGNAGE

35 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type R2 SIGNAGE

36 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type R3 SIGNAGE

37 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type EP SIGNAGE

38 NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) Sign Type DG (Example) 8-inch High Lettering SIGNAGE

39 BRYAN COUNTY SCHOOLS NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) DECEMBER 2013 Sign Type DR (Example) VARIES SIGNAGE

40 BRYAN COUNTY SCHOOLS NEW BRYAN COUNTY ELEMENTARY SCHOOL PEMBROKE (Rev. 2/7/2014) DECEMBER 2013 Sign Type PD (Example) SIGNAGE