A2.0 TRIPLE M DEVELOPMENT EXTERIOR ELEVATIONS. Rochester, MN Hwy 52 North. Apr 07, phone fax

Transcription

1 NORTH ELEVATION 1 1/8" = 1'-0" WEST ELEVATION 2 1/8" = 1'-0" SOUTH ELEVATION 3 1/8" = 1'-0" EXTERIOR ELEVATIONS A2.0 EAST ELEVATION 4 1/8" = 1'-0"

2 EXTERIOR FRAME TYPES 1 1/4" = 1'-0" 2 INTERIOR FRAME TYPES 1/4" = 1'-0" DOORS AND WINDOWS A2.1

3 1 ENLARGED STAIR PLAN 2 STAIR SECTION 3 CROSS SECTION 1/8" = 1'-0" SECTION AND STAIR A2.2

4 WALL TYPES A2.3

5 1 RECEPTION ELEVATION 2 PP/AR CABINETRY CASEWORK FOR REFERENCE-BID AS OPTION 4 MAIL/ COPY CABINETRY 5 KITCHEN@ BREAK ROOM 12 WINDOW TO WAREHOUSE INTERIOR ELEVATIONS A3.1

6 6 MEN'S ROOM ELEVATION 7 LADIES' ROOM ELEVATION 8 ACCESSIBLE TOILET ELEVATION (TYP) 9 MEN'S ROOM SINK ELEVATION 10 ACCESSIBLE DRINKING FOUNTAIN 9 LOWER LEVEL UNISEX RESTROOM 10 UNISEX RESTROOM TOILET (TYP) 11 UNISEX RESTROOM (TYP) 12 UNISEX SHOWER@CONTROL INTERIOR ELEVATIONS A3.2

7 SECTION RESILIENT TILE FLOORING A. SUBMITTALS: PRODUCT DATA AND SAMPLES.. B. FIRE-TEST RESPONSE: RESILIENT TILE HAS CRITICAL RADIANT FLUX CLASSIFICATION OF CLASS I, NOT LESS THAN 0.45 W/SQ. CM PER ASTM E 648. C. EXTRA MATERIALS: DELIVER TO OWNER 1 BOX FOR EVERY 50 BOXES OR FRACTION THEREOF, OF EACH TYPE AND COLOR OF RESILIENT FLOOR TILE INSTALLED. 2.1 RUBBER FLOOR TILE 1. SEE FINISH SCHEDULE. B. COLOR AND PATTERN: SEE FINISH SCHEDULE. C. ASTM F 1344, EXCEPT FOR HARDNESS, CLASS I-A (HOMOGENOUS RUBBER TILE, SOLID COLOR). D. WEARING SURFACE: TEXTURED OR MOLDED PATTERN. 1. MOLDED-PATTERN FIGURE: RAISED DISCS OR SQUARES. SEE FINISH SCHEDULE. E. THICKNESS: INCH (3.2 MM). F. SIZE: 12 BY 12 INCHES (304.8 BY MM) OR 24 BY 24 INCHES (609.6 BY MM). 2.2 VINYL COMPOSITION FLOOR TILE VCT ARMSTRONG B. COLOR AND PATTERN: SEE FINISH SCHEDULE. C. ASTM F 1066, CLASS 2 (THROUGH-PATTERN TILE). D. WEARING SURFACE: SMOOTH. E. THICKNESS: INCH (3.2 MM). F. SIZE: 12 BY 12 INCHES (304.8 BY MM). 2.3 INSTALLATION ACCESSORIES A. TROWELABLE LEVELING AND PATCHING COMPOUNDS: LATEX-MODIFIED, PORTLAND CEMENT- OR BLENDED HYDRAULIC CEMENT-BASED FORMULATION PROVIDED OR APPROVED BY FLOORING MANUFACTURER FOR APPLICATIONS INDICATED. B. ADHESIVES: WATER-RESISTANT TYPE RECOMMENDED BY MANUFACTURER TO SUIT RESILIENT PRODUCTS AND SUBSTRATE CONDITIONS INDICATED. C. METAL EDGE STRIPS: EXTRUDED ALUMINUM IN MAXIMUM AVAILABLE LENGTHS TO MINIMIZE JOINTS. PART 3 - EXECUTION 3.1 INSTALLATION A. PREPARE CONCRETE SUBSTRATES ACCORDING TO ASTM F 710. VERIFY THAT SUBSTRATES ARE DRY AND FREE OF CURING COMPOUNDS, SEALERS, AND HARDENERS. B. LAY OUT TILES SO TILE WIDTHS AT OPPOSITE EDGES OF ROOM ARE EQUAL AND ARE AT LEAST ONE-HALF OF A TILE. C. MATCH TILES FOR COLOR AND PATTERN BY SELECTING TILES FROM CARTONS IN SAME SEQUENCE AS MANUFACTURED AND PACKAGED. LAY TILES IN BASKET-WEAVE PATTERN WITH GRAIN DIRECTION ALTERNATING IN ADJACENT TILES. END OF SECTION BE SELECTED SECTION TOILET COMPARTMENTS A. SUBMITTALS: PRODUCT DATA, SHOP DRAWINGS, AND SAMPLES. 2.1 TOILET COMPARTMENTS AND SCREENS 1. BOBRICK. 2. SANTANA. SECTION ACOUSTICAL PANEL CEILINGS A. Submittals: Product Data and material Samples. B. Surface-Burning Characteristics of Panels: ASTM E 1264, Class A materials, tested per ASTM E 84. USG 2220 Radar with Tegular edge as basis of design SECTION RESILIENT BASE AND ACCESSORIES A. SUBMITTALS: PRODUCT DATA AND SAMPLES. B. EXTRA MATERIALS: DELIVER TO OWNER AT LEAST LINEAR FEET (LINEAR M), OF EACH TYPE AND COLOR OF RESILIENT WALL BASE INSTALLED. 2.1 WALL BASE VB JOHNSONITE OR EQUAL. B. COLOR AND PATTERN: SEE SCHEDULE. C. ASTM F 1861, TYPE TV (VINYL)] OR TYPE TS (RUBBER, VULCANIZED THERMOSET). D. GROUP (MANUFACTURING METHOD): I (SOLID). E. STYLE: STRAIGHT (TOELESS). F. MINIMUM THICKNESS: INCH (3.2 MM). G. HEIGHT: 4 INCHES (101.6 MM) OR 6 INCHES (152.4 MM). SEE ELEVATION. H. LENGTHS: COILS IN MANUFACTURER'S STANDARD LENGTHS. I. OUTSIDE CORNERS: JOB FORMED. J. INSIDE CORNERS: JOB FORMED. 2.2 RESILIENT ACCESSORY. 1. JOHNSONITE. B. COLOR: SEE SCHEDULE. C. DESCRIPTION: CARPET BAR FOR TACKLESS INSTALLATIONS. CARPET EDGE FOR GLUE-DOWN APPLICATIONS. NOSING FOR CARPET. NOSING FOR RESILIENT FLOOR COVERING. REDUCER STRIP FOR RESILIENT FLOOR COVERING AND JOINER FOR TILE AND CARPET. D. MATERIAL: RUBBER. E. PROFILE AND DIMENSIONS: AS INDICATED. 2.3 INSTALLATION ACCESSORIES A. TROWELABLE LEVELING AND PATCHING COMPOUNDS: LATEX-MODIFIED, PORTLAND CEMENT- OR BLENDED HYDRAULIC CEMENT-BASED FORMULATION PROVIDED OR APPROVED BY FLOORING MANUFACTURER FOR APPLICATIONS INDICATED. B. ADHESIVES: WATER-RESISTANT TYPE RECOMMENDED BY MANUFACTURER TO SUIT PRODUCTS AND SUBSTRATE CONDITIONS. C. STAIR-TREAD-NOSE FILLER: TWO-PART EPOXY COMPOUND RECOMMENDED BY RESILIENT TREAD MANUFACTURER TO FILL NOSING SUBSTRATES THAT DO NOT CONFORM TO TREAD CONTOURS. PART 3 - EXECUTION 3.1 INSTALLATION A. PREPARE CONCRETE SUBSTRATES ACCORDING TO ASTM F 710. VERIFY THAT SUBSTRATES ARE DRY AND FREE OF CURING COMPOUNDS, SEALERS, AND HARDENERS. B. ADHESIVELY INSTALL RESILIENT WALL BASE AND ACCESSORIES. C. INSTALL WALL BASE IN MAXIMUM LENGTHS POSSIBLE. APPLY TO WALLS, COLUMNS, PILASTERS, CASEWORK, AND OTHER PERMANENT FIXTURES IN ROOMS OR AREAS WHERE BASE IS REQUIRED. D. INSTALL STAIR-TREAD-NOSE FILLER TO NOSING SUBSTRATES THAT DO NOT CONFORM TO TREAD CONTOURS. E. INSTALL REDUCER STRIPS AT EDGES OF FLOOR COVERINGS THAT WOULD OTHERWISE BE EXPOSED. END OF SECTION NUMBER LOWER LEVEL DOORS SIZE WD HGT THK MATL GLAZING MATL EL FIRE RATING SECTION TILE CARPETING A. SUBMITTALS: PRODUCT DATA AND SAMPLES. B. EXTRA MATERIALS: DELIVER TO OWNER CARPET TILES EQUAL TO 5 PERCENT OF EACH TYPE AND COLOR CARPET TILE INSTALLED, PACKAGED WITH PROTECTIVE COVERING FOR STORAGE. 2.1 CARPET TILE, CPTT BIGELOW, COLORBEAT MODULAR AND XFACTOR. COLOR TO BE SELECTED. B. FIBER CONTENT: 100 PERCENT NYLON 6, 6; COLORSTRAND SD NYLON. C. FACE CONSTRUCTION: LEVEL-LOOP PILE. D. DENSITY: Test method in first paragraph below is applicable only to finished level-loop and cut-pile constructions with tuft heights less than 0.25 inch (6.3 mm). E. PILE THICKNESS:.107" 2.72 MM. F. SURFACE PILE WEIGHT: 14 OZ./SQ. YD. (G/SQ. M) EXCLUDING WEIGHT OF BACKINGS. G. TOTAL WEIGHT: <INSERT IN OZ./SQ. YD. (G/SQ. M) INCLUDING WEIGHT OF BACKINGS> FOR FINISHED CARPET TILE. H. PRIMARY BACKING: MANUFACTURER'S STANDARD MATERIAL. I. SECONDARY BACKING: MANUFACTURER'S STANDARD MATERIAL. J. SIZE: 24 BY 24 INCHES (610 BY 610 MM). K. CRITICAL RADIANT FLUX CLASSIFICATION: NOT LESS THAN 0.45 W/SQ. CM PER ASTM E CARPET TILE, CPTT FLOR OR INTERFACE WALK -OFF MODULAR TILE: COLOR TO BE SELECTED HARDWARE GROUP KEYSIDE ROOM ROOM NAME ROOM FINISH SCHEDULE FLOOR WALLS CEILING N S E W MATL HEIGHT 2.2 MATERIALS A. PANEL, PILASTER, AND DOOR MATERIAL: 1. STEEL SHEETS FOR COLOR-COATED FINISH: MILL-PHOSPHATIZED, CORROSION-RESISTANT STEEL SHEET; ASTM A 591/A 591M, CLASS C, OR ASTM A 653/A 653M. 2. STAINLESS-STEEL SHEET: ASTM A 666, TYPE 304, NO. 3 OR NO. 4 DIRECTIONAL POLISH. 3. PLASTIC LAMINATE: NEMA LD 3, GRADE HGS. 4. SOLID-PLASTIC, PHENOLIC CORE: SOLID PHENOLIC CORE WITH MELAMINE FACING ON BOTH SIDES, WITHOUT VISIBLE GLUE LINE OR SEAM, WITH EASED EDGES AND WITH MINIMUM 3/4-INCH- (19-MM-) THICK DOORS AND PILASTERS AND MINIMUM 1/2-INCH- (13-MM-) THICK PANELS AND SCREENS. 5. SOLID-PLASTIC, POLYMER RESIN: HIGH-DENSITY POLYETHYLENE WITH HOMOGENOUS COLOR, NOT LESS THAN 1 INCH (25 MM) THICK, WITH SEAMLESS CONSTRUCTION AND EASED EDGES. 6. COLOR: AS SELECTED. B. CORE MATERIAL FOR METAL-FACED UNITS: SOUND-DEADENING HONEYCOMB OF RESIN- IMPREGNATED KRAFT PAPER IN THICKNESS REQUIRED TO PROVIDE FINISHED THICKNESS OF 1 INCH (25 MM) MINIMUM FOR DOORS, PANELS, AND SCREENS AND 1-1/4 INCHES (32 MM) MINIMUM FOR PILASTERS. C. PILASTER SHOES AND SLEEVES (CAPS): STAINLESS STEEL OR SOLID PLASTIC, POLYMER RESIN, NOT LESS THAN 3 INCHES (75 MM) HIGH. D. BRACKETS: CONTINUOUS. 1. MATERIAL: MANUFACTURER'S STANDARD. 2.3 FABRICATION A. TOILET COMPARTMENTS: OVERHEAD BRACED AND FLOOR ANCHORED. B. URINAL SCREENS: WALL HUNG. C. METAL UNITS: INTERNALLY REINFORCE METAL PANELS FOR HARDWARE, ACCESSORIES, AND GRAB BARS. D. SOLID-PLASTIC, POLYMER-RESIN UNITS: PROVIDE ALUMINUM HEAT-SINK STRIPS AT EXPOSED BOTTOM EDGES OF PANELS AND DOORS. E. DOORS: UNLESS OTHERWISE INDICATED, 24-INCH- (610-MM-) WIDE IN-SWINGING DOORS FOR STANDARD TOILET COMPARTMENTS AND 36-INCH- (914-MM-) WIDE OUT-SWINGING DOORS WITH A MINIMUM 32-INCH- (813-MM-) WIDE CLEAR OPENING FOR COMPARTMENTS INDICATED TO BE ACCESSIBLE TO PEOPLE WITH DISABILITIES. F. DOOR HARDWARE: STAINLESS STEEL. PROVIDE UNITS THAT COMPLY WITH ACCESSIBILITY REQUIREMENTS OF AUTHORITIES HAVING JURISDICTION AT COMPARTMENTS INDICATED TO BE ACCESSIBLE TO PEOPLE WITH DISABILITIES. 1. HINGES: SELF-CLOSING TYPE, ADJUSTABLE TO HOLD DOOR OPEN AT ANY ANGLE UP TO 90 DEGREES. 2. LATCHES AND KEEPERS: RECESSED OR SURFACE-MOUNTED UNIT DESIGNED FOR EMERGENCY ACCESS AND WITH COMBINATION RUBBER-FACED DOOR STRIKE AND KEEPER. 3. COAT HOOK: COMBINATION HOOK AND RUBBER-TIPPED BUMPER, SIZED TO PREVENT DOOR FROM HITTING COMPARTMENT-MOUNTED ACCESSORIES. 4. DOOR BUMPER: RUBBER-TIPPED BUMPERS AT OUT-SWINGING DOORS OR ENTRANCE SCREEN DOORS. 5. DOOR PULL: PROVIDE AT OUT-SWINGING DOORS. PROVIDE UNITS ON BOTH SIDES OF DOORS AT COMPARTMENTS INDICATED TO BE ACCESSIBLE TO PEOPLE WITH DISABILITIES. PART 3 - EXECUTION 3.1 INSTALLATION A. INSTALL UNITS RIGID, STRAIGHT, LEVEL, AND PLUMB, WITH NOT MORE THAN 1/2 INCH (13 MM) BETWEEN PILASTERS AND PANELS AND NOT MORE THAN 1 INCH (25 MM) BETWEEN PANELS AND WALLS. PROVIDE BRACKETS, PILASTER SHOES, BRACING, AND OTHER COMPONENTS REQUIRED FOR A COMPLETE INSTALLATION. USE THEFT-RESISTANT EXPOSED FASTENERS FINISHED TO MATCH HARDWARE. USE SLEEVE NUTS FOR THROUGH-BOLT APPLICATIONS. 1. STIRRUP BRACKETS: ALIGN BRACKETS AT PILASTERS WITH BRACKETS AT WALLS. LOCATE WALL BRACKETS SO HOLES FOR WALL ANCHORS OCCUR IN MASONRY OR TILE JOINTS. 2. SET HINGES ON IN-SWINGING DOORS TO HOLD OPEN APPROXIMATELY 30 DEGREES FROM CLOSED POSITION WHEN UNLATCHED. SET HINGES ON OUT-SWINGING DOORS AND SWING DOORS IN ENTRANCE SCREENS TO RETURN TO FULLY CLOSED POSITION. END OF SECTION NUMBER MAIN LEVEL DOORS WD SIZE HGT DOOR AND FRAME SCHEDULE THK MATL FRAME GLAZING MATL EL FIRE RATING HARDWARE GROUP KEYSIDE ROOM ROOM NAME FLOOR BASE ROOM FINISH SCHEDULE WALLS CEILING N S E W MATL HEIGHT FINISHES A3.3