0.063 Extruded 6063-T5 Aluminum. Thermally Broken Blades. Thermally Broken Frame

Transcription

1 AMk / NSULATED CONTROL DAMPERS BROKEN FRAME 3965 BF 3967 BF FFM 3965 BF Broken Frame Flange-to-Duct STANDARD CONSTRUCTON Depth: 4 ( mm) 396/ (33 mm) 396 Depth ith Blades Open: 6.25 (56 mm) Minimum Height: 8 (23 mm) - Single Blade 5 (38 mm) - Multiple Blade Maximum Panel Width: 48 (29 mm) Maximum Panel Height: 6 (524 mm) Maximum Panel Size: 2 Sq.Ft. Maximum System Pressure: 4.g. ( kpa) Operating Temperature Range: -4 to +6 F Standard Finish: Mill Standard Motor nstallation: 6 Side Shaft Direct Drive Linkage: Concealed in Frame (3967 SF) Outside of Frame (3965 SF ) 3967 BF FFM Broken Frame Front-Flange Mount AVALABLE ACCESSORES Actuators [Honeyell, Belimo] End Sitch for signaling peripheral devices Jack Shaft Hand Quadrants Chain Operation for manual operation spring closed Silicone Blade and Jamb Seals FRAME:.8 Extruded 663-T5 Aluminum cci Lii.63 Extruded 663-T5 Aluminum Thermally Broken Blades Thermally Broken Frame % Aluminum Square Bar NSULATON: Polystyrene nsulation 4 V Thermally Broken Frame a Lii Cl) DWG BF BF FFM MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) ventexhc.com [

2 DUCT DUCT AMA L NSULATED CONTROL DAMPERS BROKEN FRAME 3965 BF 3967 BF FFM 3965 BF Flanged-to-Duct 3967 BF FFM Front Flange-Mount 3965 BF 3967 BF FFM J DUCT HEGHT * 2 HEGHT DUCT HE GHT.4 HEGHT j Duct Mount Frame Not Available 7 PRESSURE LMTATONS RECOMMENDED SPECFCATON Furnish and install control damper models 3965 BF 3967 BE EEM as manufactured by Alumavent nc. Bolton, Ontario. Dampers must be licensed to bear the AMCA seal. Dampers shall be 4 ( mm) deep. Blades shall be.63 (.6 mm) thick, thermally broken ith high density Polyurethane non-cfc injected foam insulation. Frame shall be.8 (2.6 mm) thick, thermally broken ith Polystyrene insulation. Axles shall be.375 (9.53 mm) extruded aluminum alloy 663-T5. Bearings shall be engineered thermo plastic (Acetal) rotating ithin a Polycarbonate outer bearing integral in frame. Blade and Jamb seals shall be Santoprene. Linkage is concealed in frame for model 3967 BF FFM and outside of frame for model 3965 BE. Air leakage through a 36 x36 (94 mm x 94 mm) damper shall not exceed 3 CFMft kpa) static pressure at standard air (as per AMCA testing). Operating temperature range shall be -4 to +6 F. 2 (5.2 L!s/m 2) against 4.g (. Drnpr Width l l DWG BF BF FFM MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) ventexinc.com [2j

3 3967 AMA T NSULATED CONTROL DAMPERS BROKEN FRAME 3965 BF 3967 BF FFM L CERTFED RATNGS 53 Alumavent nc. certifies that the 39 Series nsulated Control Dampers shon here are licensed to bear the AMCA Seal. The ratings shon are based on tests and procedures performed in accordance ith AMCA Publication 5 and comply ith the requirements of the AMCA Certified Ratings Program. The AMCA Certified Ratings Seal applies to air performance ratings and air leakage ratings. Velocity [FPMJ fr3w c = Pressure Drop [in..g] {r = Z: W to. D j.. PRESSURE DROP 36 3 Ratings Based on: AMCA Standard 5-D - f$ c& FACE VELOCTY [FPM] ntake Ducted Test Figure 5.3 Setup DEFNTON OF LEAKAGE CLASSFCATON 2) 2 (Lfsfm LEAKAGE ft/min!ft CLASS (.25 kpa) (.OkPa) (2.OkPa) (3.OkPa) A 3(5.2) N/A N/A N/A 4(2.3) 8(4.6) (55.9) 4 (7.) 2 (5.8) 2 (2) 28 (42) 35 (78) 3 4 (23) 8 (46) 2 (569) 4 (7) CONTROL DAMPER LEAKAGE RATNG Ut(t in.g (K) DAMPER SZE 4 8 Width x Height (.25 kpa) (. kpa) (2. kpa) 2 x2 (35x35mm) A 24 x24 (6lOx6lOmm) A 36 x36 (94x94mm) A 2 x48 (35x29mm) A 48 x2 (29x35mm) A 48 x36 (29x94mm) A to C,, -).) LEAKAGE [CFM/Sq.Ft.] Leakage test as conducted in accordance ith AMCA Standard 5-D-98. Holding torque applied as 6 in.-lbs./sq.ft on parallel blade dampers. AMCA Standard 5-D-98 states that air leakage is based on operation beteen 5F (O C) and 4F (4OC). DWG BF BF FFM MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) venfexinc.com [3]

4 Single AMAV[ NSULATED CONTROL DAMPERS Duct-Mount 396 Quick N Stall Duct-Mount 3965 Flanged-to-Duct STANDARD CONSTRUCTON Depth: 4 ( mm) 396/ (33 mm) 396 Depth ith Blades Open: 6.25 (56 mm) Minimum Height: 8 (23 mm) - Blade 5 (36 mm)-. Multiple Blade Maximum Panel Width: 48 (29 mm) Maximum Panel Height: 6 (524 mm) Maximum Panel Size: 2 Sq.Ft. Maximum System Pressure: 4.g. ( kpa) Operating Temperature Range: -4 to +8 F Standard Finish: Mill Standard Motor nstallation: 6 Side Shaft Direct Drive Linkage: Concealed in Frame (396/396) Outside of Frame (3965) AVALABLE ACCESSORES Actuators [Honeyell, Belimo] End Sitch for signaling peripheral devices Jack Shaft Hand Quadrants Chain Operation for manual operation spring closed Silicone Blade and Jamb Seals Specify 39 SS Salt Water Construction Specify 39 SW Available finish: Clear Anodized.8 Extruded 663-T5 Aluminum.63 Extruded 663-T5 Aluminum BEARNGS: Celcon inner bearing ithin a Polycarbonate outer bearing -FRAME NSULATON: Polystyrene nsulation DWG MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) W.ventexinc.com []

5 AMA NSULATED CONTROL DAMPERS Duct-Mount 396 Duct-Mount 3965 Flanged-to-Duct - 2 For Duct-Mount Frame specify: 396/396 For Flanged-to-Duct Frame specify: 3965 PRESSURE LMTATONS RECOMMENDED SPECFCATON Furnish and install control damper models as manufactured by Alumavent, Bolton Ontario. Dampers must be licensed to bear the AMCA seal. Dampers shall be 4 ( mm) deep. Blades shall be.63 (.6 mm) thick, thermally broken ith high density Polyurethane non-cfc injected foam insulation. Frame shall be.8 (2.6 mm) thick, ith polystyrene insulation. Axles shall be.375 (9.53 mm) thick, Aluminum square bar. Blade and Jamb seals shall be Santoprene. Linkage is concealed in frame for models and outside of frame for model Air leak 9e through a 36 x36 (94 mm x 94 mm) damper shall not exceed 3 CFMft 2 (5.2 LJs/m) against 4.g (. kpa) static pressure at standard air (as per AMCA testing). Operating temperature range shall be -4 to +8 F. Oan,pr Width lin DWG MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) ventexinc.com [2]

6 AMA NSULATED CONTROL DAMPERS p Fi53 6D CERTFED RATNGS Alumavent nc. certifies that the 39 Series nsulated Control Dampers shon here are licensed to bear the AMCA Seal. The ratings shon are based on tests and procedures performed in accordance ith AMCA Publication 5 and comply ith the requirements of the AMCA Certified Ratings Program. The AMCA Certified Ratings Seal applies to air performance ratings and sir leakage ratings. Velocity Pressure Drop [FPM [in..gj P4H Z t W D n.. PRESSURE DROP 36 3 r E r$--- FACE VELOCTY [FPM] Ratings Based on: AMCA Standard 5-D ntake Ducted Test Figure 5.3 Setup 2 (Us/rn 3min/ft 2) LEAKAGE ft CLASS (.25 kpa) (. kpa) (2. kpa) (3 kpa) A 3(5.2) N/A N/A N/A 4(2.3) 8(4.6) (55.9) 4 (7.) 2 (5.8) 2 (2) 28 (42) 35 (78) 3 4 (23) 8 (46) 2 (569) 4 (7) CONTROL DAMPER LEAKAGE RATNG PRESSURE in.g (kpa) DAMPER SZE 4 8 Width x Height (25 kpa) (. kpa) (2. kpa) 2 x2 (35x35 mm) A 24 x24 (6x mm) A 36 x36 (94x94 mm) A 2 x48 (35x29 mm) A 48 x2 (29x35mm) A 48 x36 (29x94mm) A U. D V.) U. LEAKAGE a-,,g LEAKAGE [CFM/Sq.Ft.] Leakage test as conducted in accordance ith AMCA Standard 5-D-98. Holding torque applied as 6 in.-lbs./sq.ft on parallel blade dampers. AMCA Standard 5-D-98 states that air leakage is based on operation beteen 5F (CC) and 4F (4CC). DWG MAY HEALEY ROAD BOLTON, ON. L7E 5B2 TEL (95) FAX (95) ventexinc.com [3]