Solatube SkyVault Series

Transcription

1 Soltue SkyVult Series Soltue M74 DS Dylighting System Instlltion Instrutions Prts List Quntity Pre-Assemled Roof Assemly Options * (1) 1. M74 DS Single Dome Roof Assemly with Insulted Cur Cp Flshing * M74 DS Dul Dome Roof Assemly with Insulted Cur Cp Flshing *. M74 DS Single Dome Roof Assemly with Insulted Cur Cp Flshing nd Seurity Gurd * d. M74 DS Dul Dome Roof Assemly with Insulted Cur Cp Flshing nd Seurity Gurd * Flshing Srews - #10 X 2 in (50 mm) (16) 3 Tue Belt with Belt Lth (1) Spetrlight Infinity Tues with T Loks. 24 in (610 mm) Extension Tue with Tue Fstener Kit (1) in (1220 mm) Extension Tue with Tue Fstener Kit (1) 4d. Tue Rivets (15) 5 6 d. Tue Belt with Belt Lth (1) 5 Pre-Assemled Diffuser * (1) Amplifier Assemly * (1) 6. Amplifier Rivets (15). 3/4 in (19.5 mm) Foil Tpe - 10 ft (3.0 m) (2). Amplifier Belt with Belt Lth (1) 7 Pre-Assemled Amplifier Diffuser * (1) Required Tools: 6 6 Tpe Mesure Srew Gun with Phillips Hed Rivet Gun Required Sfety Equipment Level 6 * The M74 DS Single Dome Options meet High Veloity Hurrine Zone (HVHZ) Requirements. * Components shown not inluded in ll kits, see lel on ox. 7 1

2 WARNING Do not proeed with the instlltion until you hve red the entire instrutions, inluding these wrnings. (Use of mterils or methods not uthorized y Soltue Interntionl will result in n invlid wrrnty.) Soltue Interntionl, In. (seller) ssumes no responsiility or oligtion whtsoever for the filure of n rhitet, ontrtor, instller, or uilding owner to omply with ll pplile lws, ordinnes, uilding odes, eletril odes, energy odes, fire nd sfety odes nd requirements, roof wrrnties nd dequte sfety preutions. Instlltion of this produt should e ttempted only y individuls skilled in the use of the tools nd equipment neessry for instlltion. Protet yourself nd ll persons nd property during instlltion. If you hve ny dout onerning your ompetene or expertise, onsult qulified expert efore proeeding. Instll t your own risk! Soltue produt instlltions my e dngerous nd inlude the potentil for deth, personl injury nd property dmge. The hzrdous onditions inlude ut re not limited to the following: During instlltion, the Soltue Dylighting System s refletive tues my fous sunlight, using intense het or fire. Remove protetive film only fter the prts hve een instlled. Prior to nd during instlltion, do not leve tues in ontt with omustile mterils or unttended, espeilly ner diret sunlight. Avoid skin urns. Soltue Dylighting System nd Solr Str produts my hve shrp edges. Alwys wer lether or nvs gloves while hndling nd instlling produts. Soltue produt instlltions require liming nd working t dngerous heights, inluding on ldders, sffolding, roofs nd in tti spes. Risk of deth, personl injury nd property dmge my result from fll, or from flling ojets. Use extreme ution to minimize risk of identl injury, inluding, ut not limited to the following proedures: Cler re elow your work spe of ll people, nimls nd other items. Avoid working on surfes tht re slippery or wet. Use foot-wer with exellent trtion. Use only strong, well supported ldders. Work only in lm dry wether. When in the tti, ensure tht your weight is supported t ll times with struturlly sound frming; drywll mteril is not designed to rry person s weight. To redue the risk of fire, eletri shok, nd personl injury, si sfety preutions should lwys e followed when using eletri tools, inluding lwys wering sfety goggles or other suitle eye protetion, nd ensuring work re is ler of ll eletril wires, gs pipes, wter pipes, nd other ostles. When working in the tti or other dusty res, use of msk or respirtor is reommended to void lung irrittion. Atti spes my e drk, onfined, nd sujet to extreme tempertures. Bewre of shrp protruding ojets. Do not ttempt instlltion without hving someone within rnge of your voie or lose enough to ome to your id if neessry. Soltue produts re not designed to withstnd the weight of person, tools or other ojets. Wlking or pling ojets on the system ould use personl injury nd property dmge. If the produt is dmged, the struturl pity my e wekened; therefore the system should e repired immeditely. For sfe instlltion nd use, do not devite from these instlltion instrutions. Additionl support is reommended for long vertil nd ll horizontl tue runs. Review lol uilding requirements nd onsult with pproprite uilding ode offiil for proper mteril nd plement of dditionl support. Avoid glvni retion (orrosion) if dissimilr metls re used. Eletril Components Before instlling, serviing, or lening unit, swith power off t servie pnel nd lok servie pnel to prevent power from eoming swithed on identlly. When the servie disonneting mens nnot e loked, seurely fsten prominent wrning devie suh s tg to the servie pnel. Re-Roofing Soltue produts require speil re if removed for re-roofing. In order to ensure proper removl nd re-instlltion, plese ontt your Soltue Interntionl representtive. Plese refer to the instlltion tips for the pproprite produt elow: Dylighting Systems Instlltion Tips These instrutions re step-y-step guide for the instlltion of Soltue Dylighting System in the following onditions. For other roof types, plese ontt your Soltue Interntionl representtive for dditionl informtion. Built Up Flt Roof - Single Ply/Memrne - Asphlt Shingle - Low/No Pithed - Pithed - Prefrited Curs - Metl Roof Pnels 2

3 Dylighting Systems Instlltion Tips (Continued) Allow 1/2 hour (30 min) for the instlltion exluding ur frition, prtiulrly if this is your first instlltion. During the dy, turn off ll the lights in the room to see how muh nturl light omes in through the windows, nd determine the est position for the Soltue Dylighting System. To light speifi re, ple the system over the re, not in the enter of the room. This will prevent the desired re from eing shded y tll ojets in the room. Mesure the distne from ur to diffuser level. If you don t hve enough tuing, ontt your Soltue Interntionl representtive for dditionl tuing. Avoid roof lotions shded y trees, ridges nd himneys, or ner wter hnnels or vlleys. Also void roof res with ostrutions suh s fire sprinklers, HVAC equipment, gs, wter or drin pipes, ir duts or flues nd mke sure tht the roof is dequte to endure n instlltion without dmging its wterproofing properties or wekening the uilding struture. All dhesives nd sels re reommended to e pplied to len nd dry surfe t minimum of 70 F (21 C) for mximum performne. For instlltions where high levels of soot or deris my e present it my e neessry to use foil tpe to sel ll joints nd tue sems to prevent exess deris from entering the tuing. It is reommended to use foil tpe to sel ll joints nd tue sems for instlltions in old limtes or where humid onditions my e present in order to prevent wrm or moist ir from entering the tuing. 3

4 M74 DS Instlltion Instrutions 1 Ple Pre-Assemled Roof Assemly onto Cur Note: Cur provided y others. Note: To prevent srthes do not remove protetive liner from dome until instlltion is omplete. For ese of tue ssemly nd tthment, invert Roof Assemly nd ple onto ur. Cur y others (llow for ounter flsh roofing mteril) 35 5/8 in (904 mm) inside dimension 35 5/8 in (904 mm) inside dimension Roof opening must e round with dimeter 29.5 in (749 mm) Cur Constrution Detils: Cur provided y others. Cur OD: 34 3/8 in (873 mm) x 34 3/8in (873 mm) to llow for 0.5 in (13 mm) wterproofing memrne. Metl Cur OD: 35 in (890 mm) x 35 in (890 mm). If memrne lyer is to e pplied to outside of metl ur, use ur OD ove. Frming Memer Thikness: 1.5 in (38 mm) minimum 2.5 in (64 mm) mximum inluding insultion. Cur Height: 7.5 in (191 mm) minimum. Refer to lol uilding ode requirements. Cur Aspet: Level ur top nd plum ur wlls. For sloped roofs dd riket to divert wter. 2 Assemle Extension Tue Align pre-punhed holes nd instll rivets. Bend ts out 90 deg for proper elt lignment. Remove Protetive Liner Use rivet gun to fsten rivets. d 4

5 3 Instll Extension Tue Atth extension tue to tue ollr on pre-ssemled roof ssemly. Tue sems must e on opposing sides Align 1 T Lok nd hook into ple. Continue to engge remining t loks with eh long setion of tuing resting on outside of tue or ollr. 4 Assemle Tue Belt nd Instll Belt Lth Align Tue Belt to rest on top of Belt Alignment T. d Belt Alignment T. e Close Belt Lth to fsten Tue Belt. Bend ts over on Tue Belt to lok into ple. f 5

6 5 Instll Diffuser Tue sems must e ligned to e on opposing sides. Align 1 T Lok nd hook into ple. Continue to engge remining t loks with eh long setion of tuing resting on outside of tue or ollr. 6 Instll Tue Belt Note: For proper Belt tthment ensure Tue Belt is not lmped onto Diffuser Sel. Align Tue Belt to rest on top of Belt Alignment T. Close Belt Lth to fsten Tue Belt. 7 Instll Assemled Unit into Roof Cur. 6

7 8 Fsten Roof Assemly to Cur Remove Protetive liner from dome. Flshing Srew Alternte Instrution for Multiple Tue Atthment Note: If instlling more thn 48 in (1220 mm) of tuing use the following steps.* 9 Instll Assemled Unit into Roof Cur. 10 Instll Additionl Extension Tues Atth extension tue. See step 3 for tthment method. Instll Tue Belt. See step 4 for tthment method. Instll dditionl extension tues from elow. 7

8 11 Instll Diffuser Instll diffuser. See step 5 for tthment method. Instll Tue Belt. See step 6 for tthment method. Amplifier Instlltion Instrutions 12 Instll First Amplifier Setion Instll Amplifier from elow. Align slots with ent T Loks nd instll Amplifier setion to extension tue. Bend T Lok k 90 deg. to lok Amplifier setion into ple. Bend eh T Lok out 90 deg. for Amplifier onnetion. 13 Instll Remining Amplifier Setions Bend remining T Loks to lok Amplifier setions into ple. 8

9 14 Fsten Amplifier Setions Align pre-punhed holes nd instll rivets. Align Amplifier setions to ensure flt setion overlps to sit on top of offset. Use Rivet gun to fsten rivets for eh Amplifier setion. 15 Apply Foil Tpe Apply foil tpe to over t nd opening. Apply pressure to foil tpe for proper onding. 9

10 16 Instll Tue Belt nd Amplifier Diffuser Align elt just over top edge of rivets. Instll Tue Belt. See step 4 for tthment method. Apply foil tpe to over long setion of diffuser to ensure proper sel. d Instll Amplifier Diffuser. See step 5 for tthment method. Instll Amplifier Belt to rest on edge of diffuser sel. e 17 Now you n enjoy the enefits of your Soltue Dylighting System nd the high performne, nturl lighting it provides. 10

11 Colletor with Ryender HD Instlltion Instrutions Appendix Prts List Quntity M74 DS Dome (1) 2 Dome Retiner Bnd Assemly (1) 3 M74 DS Cylinder Assemly with Ryender HD (1) Wire Rope Bridle Assemly (4) Cone Fstener Kit 5. Cone Clmp (4). Flshing Srews - #10 X 2 in (50mm) (24). Cone Clmp Rivet (17) Pre-Assemled Roof Assemly Options * (1). M74 DS Single Dome Roof Assemly with Insulted Cur Cp Flshing * 6. M74 DS Dul Dome Roof Assemly with Insulted Cur Cp Flshing *. M74 DS Single Dome Roof Assemly with Insulted Cur Cp Flshing nd Seurity Gurd * d. M74 DS Dul Dome Roof Assemly with Insulted Cur Cp Flshing nd Seurity Gurd * 7 Tue Belt with Belt Lth (1) Required Tools: Tpe Mesure Rivet Gun 6 Srew Gun with Phillips Hed Drill Bit #30 Required Sfety Equipment Nut Driver 3/8 in ( mm) * The M74 DS Single Dome Options meet High Veloity Hurrine Zone (HVHZ) Requirements. * Components shown not inluded in ll kits, see lel on ox. 7 11

12 1 Remove Bridle Assemly Remove ll 4 Bridle Assemlies Bridle ssemly Do not remove Bridles from se of flshing. CAUTION: Unssemled Bridle Assemlies re Trip Hzrd. Use Cution During This Step. 2 Remove Colletor from Flshing Remove olletor nd set side. 3 Ple Roof Assemly onto Cur CAUTION: Unssemled Bridle Assemlies re Trip Hzrd. Use Cution During This Step. Plese return to step 2 of the SkyVult Series instlltion instrutions for tuing nd diffuser tthment efore proeeding to step 4 of these instrutions. 12

13 4 Re-Instll Colletor Crefully ple nd enter olletor over roof ssemly. 5 Adjust Colletor Position In the Northern Hemisphere position the Colletor so the refletive side of the Light Trker is fing due South (North in the Southern Hemisphere). 6 Fsten Cone Clmps Align Cone Clmps with dimples nd drill 2 holes into one se. Cone Clmp Insert 4 rivets nd fsten Cone Clmps using rivet gun. 13

14 7 Re-Atth Bridle Assemlies Crefully ple nd enter olletor over roof ssemly. 8 Fsten Roof Assemly to Cur Fsten 6 flshing srews per side. Align Dome Retiner Clips for Wire Rope Bridle tthment Flshing Srew Tighten until flush. Wire Rope Bridle Assemly 14