SPECIFICATIONS...02-M3 TECHNICAL DATA...03-M3 TYPICAL DETAILS...04-M3 and 05-M3

Transcription

1 0- Table of Contents SECTION PAGE SPECIFICATIONS...0- TECHNICAL DATA...0- TYPICAL DETAILS...0- and 0- Project: Private Condominiums, iami, FL Due to the diversity in state/provincial, local, and federal laws and codes that govern the design and application of architectural products, it is the responsibility of the individual architect, owner, and installer to ensure that products selected for use on projects comply with all applicable building codes and laws. U.S. Aluminum exercises no control over the use or application of its products, glazing materials, and operating hardware, and assumes no responsibility thereof. The rapidly changing technology within the architectural aluminum products industry demands that U.S. Aluminum reserve the right to revise, discontinue or change any product line, specification or electronic media without prior written notice. NOTE: Dimensions in parentheses ( ) are millimeters unless otherwise noted. Other metric units shown in this publication are: m - meter Kg - kilogram Pa - pascal KPa - kilopascal Pa - megapascal

2 0- Specifications SECTION HURRICANE RESISTANT DOORS NOA: Out-Swing SERIES FACE WIDTH DEPTH GLAZING INFILL GLAZING ETHOD BAL-0 -/" (9.) " (0.8) 9/" () Factory Pre-Glazed I. GENERAL DESCRIPTION Work Included: The glazing contractor shall furnish all necessary materials, labor, and equipment for the complete installation of aluminum terrace doors and framing as detailed on the drawings and specified herein. Work Not Included: A Structural support of the framing system, wood framing, structural steel, masonry, interior trim, and final cleaning. QUALITY ASSURANCE For purposes of designating type and quality for work in this section, drawings and specifications are based on U.S. Aluminum, Series BAL-0 Balcony/Terrace Door, -/" (9.) vertical face dimension and " (0.8) depth. A " x (. x ) or -/" x (. x ) frame is available for moderate traffic applications. When substitute products are to be considered, supporting technical literature, samples, and drawings must be submitted 0 days prior to bid date in order to make a valid comparison of the products involved. PERFORANCE REQUIREENTS eets all iami-dade County, Florida air, water, structural, and impact requirements. Air Infiltration: When closed and locked, the test specimen shall be tested in accordance with AST E 8 and shall not exceed 0. cfm/sq. ft. at a test pressure differential of. PSF. Water Resistance: When closed and locked, the test specimen shall be tested in accordance with AST E and AST E there shall be no uncontrolled leakage as defined in the test method at a static air pressure differential of 8 PSF. (single doors) Large and Small issile Impact Test: aximum design pressure of +00 psf +0/-00 psf (large missile impact) and +0 psf/-0 psf (small missile impact). Forced Entry Resistance - 00 pound concentrated load. II. PRODUCTS/ATERIALS Door members shall be extruded architectural aluminum 0-T alloy and temper. ajor portions of all door sections, shall be nominal. (.). Wall thickness of frame members shall be nominal. (.). Screws, nuts, washers, bolts, rivets, and other fastening devices shall be aluminum, stainless steel or other non-corrosive materials. DOOR AND FRAE CONSTRUCTION Door corners are to be accurately joined using "Secure Bolt" construction. The weather seals shall be open cell urethane foam core bonded to a U.V. stabilized polyurethane liner. Doors shall have non-removable interior glass stops with custom E.P.D.. spacer by Tremco, DOW 99 Structural Silicone, and E.P.D.. Wedge by Tremco. No exposed screws shall be permitted except for anchoring. Four-point locking hardware shall be as recommended by manufacturer. Finishes available are: Polished Brass, Brushed Brass, atte Aluminum, Polished Chrome, Brushed Aluminum, White, and Black. Door leaves shall have a pair and a half (minimum) of heavy-duty mortised " x -/" (0. x.) long butt hinges with non-removable stainless steel pins. If hardware is to be furnished by others, templates and physical hardware must be submitted prior to any fabrication being started. FINISH All exposed framing surfaces shall be free of scratches and other serious blemishes. Standard aluminum extrusions shall be given a Kynar 00 AAA 0 paint. (Specify one of the following): Bone White Statuary Bronze Kynar 00 (Special Order) with the requirements of AAA 0. Color shall be (specify). Class anodized extrusions shall be given a caustic etch followed by a anodic oxide treatment to obtain... Clear Anodize Bronze Anodize III. EXECUTION INSTALLATION All items under this heading shall be set by a qualified installer in their correct locations as shown in the details and shall be level, square, plumb, and at proper elevation and in alignment with other work in accordance with the manufacturer's installation instructions and approved shop drawings. All joints between entrance framing and the building structure shall be sealed in order to secure a watertight installation. Upon completion of the installation of the entrances, it shall be the contractor's responsibility to make all necessary final adjustments to attain normal operation of each door and its mechanical hardware. PROTECTION AND CLEANING After installation the General Contractor shall adequately protect exposed portions of the aluminum entrance work from damage by grinding and polishing compounds, plaster, lime, acid, cement or other contaminants. The General Contractor shall be responsible for final cleaning. IV. OPTIONS Concealed Overhead Closers Exposed Heavy-Duty Closers Standard " (.) Round Push/Pull Sets Three Point Locking System With Exterior Cylinder and Interior Thumbturn

3 0- Technical Data The BAL-0 Balcony/Terrace Door is elegantly designed for high rise applications such as hotels, condominiums, and office buildings. Being tested for both small and large missile impact resistance, as well as its high performance for water resistance, makes the BAL-0 meet and exceed all commercial and high-rise condominium developer requirements with the highest level of quality. With the growing need for a commercial impact resistant product in the residential market, the BAL-0 by U.S. Aluminum has topped the list for single terrace and balcony doors. Series BAL-0 Impact Resistant Out-Swing Balcony/Terrace Door (Exterior View) Standard Features: Factory Pre-Glazed With Structural Silicone aximum Panel Size: " x 08" (0 x ) Heavy Commercial Grade aximum Frame Height 0" (08), Including -/" (.) Top Rail and 8" (0.) Bottom Rail " (.) High Water Threshold Heavy-Duty Internal Corner Clips " x ( x ) or -/" x (. x ) Door Frame 0. (.) Nominal Wall Thickness, Door and Frame -/ Pair of " x -/" (0. x.) ortised Aluminum Butt Hinges With Non-Removable Stainless Steel Hinge Pins for Door Opening Heights Up to 8" () Two Pairs of " x -/" (0. x.) ortised Aluminum Butt Hinges With Non-Removable Stainless Steel Hinge Pins for Door Opening Heights Greater Than 8" () Double Rows of Weather Seals Stainless Steel Four-Point Locking System Including Latch Lock, Deadbolt Lock With Shoot-Bolts Top and Bottom Solid Brass Lever Handle by Ashland Non-Removable Interior Glass Stops Wet Glazing ethod Options: Custom Finishes: AAA 0 Compliant Painted Finishes Concealed Overhead Closers Surface ounted Heavy-Duty Closers Large issile 9/" () VS Laminated Impact Glass Laminated Glass Composition: /" () Heat Strengthened Laminated Glass 0.0 VS0 Interlayer Small issile 9/" () PVB Laminated Impact Glass Laminated Glass Composition: 0.90" PVB Interlayer Glass Tint Available as Selected by the Architect/Owner Designer Latch Lock Hardware Finishes Available: Black, Brushed Aluminum, Brushed Brass, atte Aluminum, Polished Brass, Polished Chrome, and White. Open for Glazing by Customer Designer Latch Lock

4 0- Typical Details OUT-SWING DOORS AND FRAES /" (.) DLD-0 -/" x (. x ) at /" (.) DLD- -/" DLD-0 () DLD- DOOR FRAE WIDTH DLD- BCE0 () TYPICAL ELEVATION OUT-SWING DOOR FRAE OPENING HEIGHT FRAE OPENING HEIGHT TRANSO HEIGHT DOOR FRAE HEIGHT DOOR FRAE HEIGHT DOOR OPENING HEIGHT D.O.H. -/" -/" (.8) " (0.8) 9-/" (.) /8" (.) DLD-0 DLD-0 DLD- DLD-0 DLD-0 DLD-0 DLD- DLD-0 " (.) DLD- Water Resistant Threshold -/" x (. x ) /" (.) -/" DLD- -/8" (.) DOOR OPENING WIDTH DOOR FRAE WIDTH BCE-0 DLD- DLD- -/8" (.) -/" DOOR OPENING WIDTH DOOR FRAE WIDTH /" (.) -/" x (. x ) NOT TO SCALE

5 0- OUT-SWING DOOR FRAES UP/OVER FRAE FOR SINGLE DOOR Butt Hinges " x 8" D.O. PART NO.* BAL0W0FN () DLD- BCE0 DLD-09 (Typ.) DLD-9 BCE0 " () Frame without 9-/" x 8" or 9-/" x 98" Butt Hinges " x 9" D.O. BAL0WFN * Specify Right or Left Hand when ordering. -/" DLD- EXTERIOR DLD-08 (Typ.) DLD- FRAE WIDTH (Optional) DLD-0 TRANSO FRAE PART NO.* " (0.8) Butt Hinges " x 8" D.O. BAL0W0FT DLD-0 DLD-0 Frame with 9-/" x 0" Butt Hinges " x 9" D.O. BAL0WFT * Specify Right or Left Hand when ordering. aximum door frame size 9-/" x 0' (00 x 08) with ; 9-/" x 9' " (00 x 9) without BAL-0 Balcony Door Frame Standard Features: Factory Assembled -/" x (. x ) Door Stainless Steel Butt Hinges With Aluminum Back-Up Plates " (.) Water Resistant Threshold Pre-Drilled for Anchors Stainless Steel Water Resistant Keeper Silicone Sealed Corner Joinery BAL-0 Balcony Door Frame Options: " () Door s FRAE HEIGHT LEAF HEIGHT DLD-0 DLD-0 DLD-09 EXTERIOR DLD-0 DLD-08 DLD- " (0.8) " (.) DLD-0 Alternate Location for Typical Anchors at Header -/" x (. x ) at /" (.) DLD- -/" DLD-0 Access Hole DLD- Water Resistant Threshold DLD-0 DLD-0 () DLD- DOOR FRAE WIDTH