Health and Safety in Employment Act (Amended 1993)

Transcription

1 6711R RESENE PAINTING This specification has been written in good faith with information available at the time. It is assumed that the nominated applicator has the necessary experience and equipment to fulfil the requirements of this specification. If any substrate differs or is missing from this specification, please advise the writer of it. 1. GENERAL Related work 1.1 RELATED SECTIONS Refer to ~ for ~. Documents 1.2 DOCUMENTS REFERRED TO Documents referred to in this section are: Health and Safety in Employment Act (Amended 1993) Occupational Health and Safety Service (OSH) publication: Guidelines to the provision of facilities and general safety in the construction industry. Occupational Health and Safety Service (OSH) publication: Guidelines for the management of lead-based paint. Report of the Asbestos Advisory Committee to the Minister of Labour April 1999 Documents listed above and cited in the clauses that follow are part of this specification. However, this specification takes precedence in the event of it being at variance with the cited document. 1.3 MANUFACTURER S DOCUMENTS Manufacturer s and supplier s documents relating to work in this section are: One-Line Specifications and Product Data Manual - Putting Your Safety First Copies of the above literature are available by phoning 0800 RESENE ( ) or visiting Requirements of the Contractor in the Completion of Defined Works 1.4 CONTROL SAMPLES Prepare samples of the finished work, including the specified preparation if required by the architect or designer. Refer to 4. SCHEDULES. Obtain written approval from the Principal s representative before proceeding. Use the Architectural Sample Box as a basis of standard where appropriate. Control samples may, after written approval, be used for comparative testing of dry film thicknesses of the complete coating systems. 1.5 SUPERVISED CONTROL SAMPLES Prepare samples of the finished work including the specified preparation. Refer to 4. SCHEDULES. Make arrangements for the full-time supervision of the application of each coat. Obtain written approval before proceeding. Control samples may, after written approval, be used for comparative testing of dry film thicknesses of the complete coating systems. 1.6 QUALIFICATION Painters to be experienced competent workers, familiar with the materials and the techniques specified and with the coating systems and be members of the Master Painters New Zealand Association Inc. 6711R RESENE PAINTING Page 1

2 1.7 HEALTH AND SAFETY Comply with the requirements of the Health and Safety in Employment Act (Amended 1993) and the Occupational Safety and Health Service (OSH) publication Guidelines for the provision of facilities and general safety in the construction industry. If the elimination or isolation of potential hazards is not possible, then minimise hazards in this work on site by using the proper equipment and techniques as required by the Painters Hazard handbook and Putting Your Safety First handbook. The Contractor must supply protective clothing and equipment, inform the Principal s representative as well as the employees and others on site of the hazards and put in place procedures for dealing with emergencies. Refer to the Occupational Safety and Health Service (OSH) publication Guidelines for the management of lead-based paint for the required procedures and precautions when: Treating/removing lead-based paint; Burning off lead-based paint; Sanding off lead-based paint; Using solventborne paint removers on lead-based paint. 1.8 MATERIAL SAFETY DATA SHEETS Ensure all applicators have read the material safety data sheet for each product prior to use and comply with the required safety procedures. Material safety data sheets for all products can be obtained from (ring 0800 RESENE, or access from Keep all sheets on site. Guarantees 1.9 WARRANTY Warrant this work under normal conditions of use against failure. Warranty period - materials: According to 1(v) Durability of Paint Systems in the One-Line Specifications and Product Data Manual Warranty period - execution: 3 years Refer to the PRELIMINARIES AND GENERAL section for the required form of warranty agreement and details of when completed warranty must be submitted. Performance 1.10 RESENE INSPECTION Permit representatives of to inspect the work in progress and to take samples of their products from site if requested INSPECTION OF THE WORK Inspection of the whole of the work at each of the stages set out in 4. SCHEDULES may be made by the Principal s representative. If inspection is required, agree on a programme that will facilitate such inspection, including notification when each part and stage of the work is ready for inspection prior to the work commencing. 2. PRODUCTS Materials 2.1 MATERIALS GENERALLY All coatings to be products (which are guaranteed for consistency and performance under ISO 9001 and APAS) prepared, mixed and applied as directed in the One-Line Specifications and Product Data Manual. Paint containers not in use are to have their lids or closures firmly affixed to prevent evaporation and contamination from foreign bodies. 6711R RESENE PAINTING Page 2

3 2.2 COLOURS Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 1.9 Selection of Colour. Differently coloured paints will vary in price, opacity and durability. Colours need to be clearly identified before tendering to allow reasonable pricing that will consider both price and the number of coats needed to obtain opacity. normally only specify two coats of colour but with certain colours, such as yellows and oranges, three coats may be needed. Your representative will assist. colours do vary in durability. Check with your local representative if this is an important requirement of the job. Before any work commences painters should verify, with Architects or specifying authority, that their paint matches a previously supplied standard card or panel. The gloss level could also be checked at this stage. Large wall areas that require more than one container of paint per coat should have enough paint boxed together to complete the final coat. This will not apply if a single factory batch of paint, rather than shop tinted paint, is applied. Please ensure that the colour purchased is the same as selected. accepts no responsibility for the application of incorrect colours. Darker colours over damp timber may result in faster than normal drying out and subsequent cracking. This may occur if timber is wet before painting or becomes wet for any reason at a later date. This should be taken into account when choosing colours. 2.3 PAINT SYSTEMS EXTERIOR PAINT SYSTEMS Apply the listed systems for the following substrates: Prep Coat products Finish EXTERIOR CEMENTITIOUS SURFACES 1e 1.2 D83 TP Limelock D809 1st SCS Concrete Primer D405 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 4 th Multishield + D54a (Optional) D83 1 st SP Sonyx 101 D30 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 4 th Multishield + D54a (Optional) EXTERIOR TIMBERS 2e 1.1 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss EXTERIOR TIMBERS, STAINS AND CLEAR FINISHES 2e 3.5 D82 1 st Waterborne Woodsman D57a Waterborne flat 2 nd Waterborne Woodsman D57a Waterborne flat 3 rd Waterborne Woodsman D57a (after 3 months) EXTERIOR TIMBER JOINERY 3e 1.1 D82 & 1 st NRS Quick Dry D45 TimberLock TTS Wood Primer D40 D48 2 nd Enamacryl D309 Waterborne gloss 6711R RESENE PAINTING Page 3

4 3 rd Enamacryl D309 Waterborne gloss EXTERIOR TIMBER DECKS, PERGOLAS AND FENCES 4e 1.3 D82 1 st NRS Lumbersider D34 NSF Resitex Std D70 5e EXTERIOR GALVANISED STEEL AND ZINCALUME 5e 1.1 D89 1 st NW Galvo-Prime D402 R Galvo One D41 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss EXTERIOR FERROUS METALS 6e 1.2 D801 1 st Rust Arrest RA30 2 nd Rust Arrest RA30 3 rd Lustacryl D310 Waterborne semi-gloss 4 th Lustacryl D310 Waterborne semi-gloss EXTERIOR NON-FERROUS METALS 7e 1.1 D89 1 st NRS Vinyl Etch RA31 WNW Galvo-Prime D402 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss EXTERIOR CEDAR 8e 1.3 D82 & 1 st NC Quick Dry D45 TimberLock WC Wood Primer D40 D48 D82 & 1 st SP Lumbersider D34 Waterborne satin T/Lock D48 EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS 10e 1.1 D803 1 st Membrane Roofing Primer D49 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss GLASS, GLAZED TILES, BAKED ENAMEL SYSTEMS 11e 1.1 D802 or 1 st Smooth Surface Sealer D47 D803 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss GLASS REINFORCED POLYESTER, EPOXY, PVC, ACRYLIC SHEETING, POLYSTYRENE, POLYCARBONATE 12e 1.1 D803 1 st Hi-Glo D31 Waterborne gloss 2 nd Hi-Glo D31 Waterborne gloss BRICK AND TERRACOTTA 13e 1.3 D802 1 st SSP Lumbersider D34 Waterborne satin D802 1 st ES Sureseal D42 EXTERIOR CANVAS AND AWNINGS 16e 1.3 D803 1 st Lumbersider D34 Waterborne satin 6711R RESENE PAINTING Page 4

5 WATERPROOFING MEMBRANES 17e 1.4 D83 TP: Limelock D809 1 st SCS Concrete Primer D405 SP X-200 D62 Waterborne low sheen 2 nd X-200 D62 Waterborne low sheen 3 rd X-200 D62 Waterborne low sheen 4 th Multishield+ D54a (optional) HEAVY DUTY FLOOR COATINGS 18e/i 2.1 U D83 1 st CS Armourcote 510 RA40* 2 nd Uracryl 403 RA56 Solventborne gloss * Add Industrial SRG Grit to this coat for non-skid version. ANTI GRAFFITI SYSTEMS 19e 2.1 CA D83 1 st Armourcote 510 RA47 2 nd Uracryl 403 RA56 Pigmented 3 rd Uracryl 403 RA56 Pigmented 4 th Uracryl 403 RA56 Clear TEXTURED AND SPECIALIST COATINGS (Including Harditex) 20e 1.3 RS D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Lumbersider D34* 3 rd Resitex D70 Waterborne textured 4 th Multishield+ D54a (Optional) * For additional waterproofing, replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Resitex. PAINT EFFECTS 21e/i 1.5 C 1 st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3 rd Paint Effects Medium D307 Waterborne Flat - colourwashing EXTERIOR MILD STEELS, NEW FERROUS METALS (Medium and long-term protection) 22e 2.1 EMT D st MT Zincilate 10 RA20 Inorganic zinc D801.8 D nd Armourcote 512 RA407 High build epoxy gloss EXTERIOR NEW HOT DIPPED GALVANISED MILD STEEL (Medium and long-term protection) 23e 2.1 ELT D st LT Vinyl Etch RA31 Etch primer D nd Armourcote 512 RA407 High build epoxy gloss EXTERIOR NEW METAL SPRAY COATINGS (METAL ARC OR ZINC SPRAY) (Medium and long-term protection) 24e 2.1 ULT * 1 st LT Armourcote 220 RA34 Epoxy primer 2 nd Uracryl 403 RA56 Acrylic urethane 3 rd Uracryl 403 RA56 Acrylic urethane 4 th Uracryl 403 UVS Clear RA56 Acrylic urethane clear gloss * Refer to the Engineered Coating Systems manual for preparation EXTERIOR METALLIC FINISHES Metallic finish on cementitious plaster 25e 1.3/5 D83 1 st Quick Dry D45 2 nd Lumbersider D34 3 rd Enamacryl Metallic D309a Waterborne metallic 4 th Enamacryl Metallic D309a Waterborne metallic 5 th Multishield+ D54a (Optional) 6711R RESENE PAINTING Page 5

6 INTERIOR PAINT SYSTEMS Apply the listed systems for the following substrates: Prep Coat products Finish INTERIOR CEMENTITIOUS SURFACES 1i 1.2 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss D83 1 st SP Lustacryl D310 Waterborne semi-gloss 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss INTERIOR TIMBER 2i 1.1 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 POV Smooth Surface Sealer D47 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss INTERIOR TIMBER, STAINS AND CLEAR FINISHES 2i 4.1 D82 1 st SF Waterborne Colorwood D50a 2 nd Polyflat D52* 3 rd Polygloss D52 Solventborne gloss 4 th Polygloss D52 Solventborne gloss * For particle and fibreboard, replace with one coat of Aquaclear D82 1 st CF Waterborne Colorwood Reducing Base D50a (optional) 2 nd Polyflat D52* 3 rd Polygloss D52 Solventborne gloss 4 th Polygloss D52 Solventborne gloss * For particle and fibreboard, replace with one coat of Aquaclear D82 1 st HDF Polythane D53 2 nd Polythane D53 3 rd Polythane D53 Solventborne gloss 4 th Polythane D53 Solventborne gloss * For particle and fibreboard, replace with one coat of Particle Board Sealer. INTERIOR TIMBER JOINERY 3i 1.1 D82 & 1 st NRS Quick Dry D45 TimberLock TTS Wood Primer D40 D48 POV Smooth Surface Sealer D47 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss INTERIOR FERROUS METALS 6i 1.1 D801 1 st Rust Arrest RA30 2 nd Quick Dry D45 3 rd Enamacryl D309 Waterborne gloss 4 th Enamacryl D309 Waterborne gloss INTERIOR NON-FERROUS METALS 7i 1.1 D89 1 st NRS Vinyl Etch RA31 WNW Galvo-Prime D402 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss 6711R RESENE PAINTING Page 6

7 INTERIOR GLASS, GLAZED TILES, FORMICA, POLYETHYLENE, POLYPROPYLENE AND BAKED ENAMEL SYSTEMS 11i 1.1 D802 1 st Smooth Surface Sealer D47 or D803 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss INTERIOR GLASS REINFORCED POLYESTER, GLASS REINFORCED EPOXY, PVC, ACRYLIC SHEETING 12i 1.1 D803 1 st Enamacryl D309 Waterborne gloss 2 nd Enamacryl D309 Waterborne gloss INTERIOR BRICK AND TERRACOTTA 13i 1.2 D802 1 st SSP Lustacryl D310 Waterborne semi-gloss 2 nd Lustacryl D310 Waterborne semi-gloss D802 1 st PCS Sureseal D42 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss INTERIOR BRICK AND TERRACOTTA, CLEAR FINISHES 13e/i 4.5 D802 1 st PS Aquapel D65 Solventborne flat 2 nd Aquapel D65 Solventborne flat 3 rd Aquapel D65 Solventborne flat INTERIOR PAPER FACED PLASTER/SOLID PLASTER/FIBROUS PLASTER 15i 1.4 SCL4 D84, D85 1 st NRS Broadwall Acrylic Wallboard Sealer D403 D87, D807 WS 2 nd Zylone SpaceCote D311 Waterborne low sheen 3 rd Zylone SpaceCote D311 Waterborne low sheen CANVAS, SCANDATEX AND HESSIAN 16i 1.3 D803 1 st NRS Lumbersider D34 D803 1 st SR Sureseal D42 SPECIALIST FLOOR SYSTEMS 18i 2.2 D83 1 st TS Wood Primer D40 CS Sidewalk D38 GCS Smooth Surface Sealer D47 MPB Quick Dry D45 2 nd Sidewalk D38* Solventborne semi-gloss 3 rd Sidewalk D38 Solventborne semi-gloss * Add SRG Grit to this coat for non skid version ANTI GRAFFITI SYSTEMS 19i 1.1 OA 1 st WBS Aquapoxy RA42 Pigmented 2 nd Aquapoxy RA42 Pigmented 3 rd Aquapoxy RA42 Pigmented TEXTURED COATINGS 20e/i 1.5 D83/ TP Limelock D809 D84 1 st SCS Concrete Primer D405 2 nd Lumbersider D34* 6711R RESENE PAINTING Page 7

8 3 rd Sandtex D71 Waterborne fine texture * For additional waterproofing replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Sandtex. 20e/i 1.5 D83/ TP Limelock D809 D84 1 st SP Lumbersider D34 2 nd Sandtex D71 Waterborne fine texture 3 rd Sandtex D71 Waterborne fine texture * For additional waterproofing replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Sandtex. PAINT EFFECTS 21e/i 1.5 C 1 st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3 rd Paint Effects Medium D307 Waterborne flat - colourwashing INTERIOR MILD STEELS 22i 2.1 AF D801.1 D801.8 D st Armourcote 210 RA35 Alkyd primer or D nd Armourcote 608 RA72 Alkyd gloss INTERIOR METALLIC FINISHES Waterborne metallic finish on Paperfaced Plasterboard 25i 1.3/51 D84, 1 st Broadwall AWS D403 D85 2 nd Lumbersider D34 3 rd Enamacryl Metallic D309a Waterborne metallic 4 th Enamacryl Metallic D309a Waterborne metallic 5 th Aquaclear D59 (Optional) 2.4 THINNERS/ADDITIVES Use only if and when expressly directed by for their particular product in a particular application. Accessories 2.5 ACCESSORIES Contact your local ColorShop for a full range of accessories and usage advice. 3. EXECUTION Conditions 3.1 EXECUTION To conform with required trade practice, which shall be deemed to include those methods, practices and techniques contained in AS/NZS 2311:2000 Guide to the painting of buildings and the Occupational Safety and Health (OSH) publication: Guidelines for the provision of facilities and general safety in the construction industry. 3.2 TREATED SURFACES Where surfaces have been treated with curing agents, preservatives, fire retardants, or similar, check with the treatment manufacturer that coating materials are compatible with the treatment and do not inhibit its performance. If they are not compatible, obtain instructions from the treatment manufacturer before proceeding. 3.3 ANCILLARY SURFACES The descriptions of areas to be coated given in schedules and elsewhere are of necessity simplified. Coat all ancillary exposed surfaces to match similar or adjacent materials or areas, except where a fair-faced natural finish is required or items are completely prefinished. In cases of doubt obtain written instructions from the Principal s representative before proceeding. 6711R RESENE PAINTING Page 8

9 The Contractor must complete any work obviously necessary for the proper and entire completion of the contract even if not specifically covered by this specification without extra cost to the Principal. 3.4 HARDWARE Do not paint hinges or hardware that cannot be removed. Before commencing work carefully remove hardware, fixtures and fittings, set aside where they cannot be damaged or misplaced and replace on completion. Refer to 4. SCHEDULES for hardware, fixtures and fittings for removal. 3.5 PROTECTION Supply, lay and fix all dropsheets, coverings and masking necessary to protect nonspecified surfaces, adjoining, fixtures, fittings and spaces from paint drops, spots, spray and damage. Application - preparatory work 3.6 SURFACE PREPARATION Refer to the One-Line Specifications and Product Data Manual for surface preparation sheets (or obtain them by calling 0800 RESENE, or from the website listed in the materials systems schedule clauses. Carry out all the preparatory work required by them for each of the substrates. Use Broadwall Surface Prep. as a surfacer to achieve a Level 5 finish on interior wallboards. 3.7 LEAD-BASED PAINT, ASBESTOS If present, handle lead-based paint and asbestos as required by the Putting Your Safety First booklet and the Occupational Safety and Health (OSH) publication: Guidelines for the management of lead-based paint. For further information read Report of the Asbestos Advisory Committee to the Minister of Labour April 1999 or contact. Removal and/or disposal of asbestos containing materials may require special permission and a license. Contact your local Council office to determine your obligations under their bylaws. 3.8 SHARP EDGES, CRACKS AND HOLES For timber refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section Standard of Finish. Sand sharp edges on timber to a rounded profile to ensure adequate paint cover. Apply a stripe coat of each specified coating on steelwork sharp edges and welds, in addition to the specified coat, to achieve the correct film build and maximise the potential of the paint system. Sand, grind or file sharp edges on other substrates to a rounded profile where practicable. 3.9 REMEDIAL WORK If any substrate or surface, that even with the preparation work called for in this section, cannot be brought up to a standard that will allow painting or clear finishing of the required standard then do not proceed until remedial work is carried out GAP FILLING Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section Gap Filling. Thoroughly clean and prepare cracks, holes, indented and damaged surfaces for filling. A special primer is needed with many substrates, while on others the filler can interfere with the coating. Check carefully and only use fillers in strict accordance with the manufacturer s directions. Elastomeric sealants that can tolerate 30% movement should only be used where gaps exist between different substrates or for expansion joints. Do not use elastomeric sealants for general hole filling. Do not paint over elastomeric sealants because they are liable to bleed plasticiser and are much more flexible than the paint. 6711R RESENE PAINTING Page 9

10 Fillers such as Jointflex or Epox-O-Bond Epoxy Filler are recommended on exterior concrete and interior concrete in wet areas. Where sealants are required, check with the sealant manufacturer regarding correct priming and that overcoating materials are compatible with the sealant and do not inhibit its performance. If they are not compatible, obtain instructions from the sealant manufacturer before proceeding OFF SITE WORK Carry out all this work, where possible under cover, in a suitable environment with suitable lighting. Store all items, both before and after coating, in a clean, dry area protected from the weather and mechanical damage, properly stacked and spaced to allow air circulation and to prevent sticking PRIMING JOINERY Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section Machine Priming of Timber and Section Effect of Timber Species. Ensure L.O.S.P. treated joinery has dried sufficiently to lose all solvent odour. Pre-treat bare timber with TimberLock (Data Sheet D48) to improve the durability of subsequent coats. Allow TimberLock to dry for 24 hours then wipe off any still tacky material with a Turps wet rag. Liberally coat end grain, allow to soak in and then recoat. After TimberLock has dried, prime with Wood Primer or Quick Dry Acrylic Primer Undercoat CONCEALED JOINERY SURFACES Where off-site coatings are specified they must be applied to all surfaces especially including those concealed when incorporated into the building CONCEALED METAL SURFACES Apply primer to all surfaces that will be concealed when incorporated into the building EXTERNAL DOORS Prime or seal and paint all edges before hanging BEAD GLAZING Joinery to be stained, varnished, or painted to have the first two coats, or the primer and one undercoat, applied to rebates and beads before glazing. This is especially important with clears. TimberLock is strongly recommended, particularly if there is a risk of water ponding PUTTY FRONTING According to the putty manufacturer's instructions allow putty to harden, then prime with Wood Primer (Data Sheet D40) or Quick Dry Acrylic Primer Undercoat (Data Sheet D45). Fully protect the putty by completing the coating system as soon as it is sufficiently firm. Application - generally 3.18 PAINTING GENERALLY Comply with the One-Line Specifications and Product Data Sheets, product labels and the additional requirements of this work section. All paints must be brought onto the job by the Contractor in their original sealed containers and be made available for inspection prior to application. Any materials supplied by the Contractor that differ from the material specified in this contract must be immediately removed from the job by the Contractor upon the Contractor being requested to do so. No painting shall begin on any area until the approval of the Principal s representative is given. 6711R RESENE PAINTING Page 10

11 3.19 MIXING All paints to be thoroughly mixed. Incorporate any settled pigment and ensure the paint is homogenous ENVIRONMENT Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 6.3 Climatic Conditions. Defer painting of exterior surfaces until weather conditions are favourable - warm dry days without frost or heavy dews are preferred. Avoid painting in direct sunlight any surfaces that absorb heat excessively. Do not apply paint if the surface is less than 5 C above dew point, the relative humidity exceeds 85% (unless special precautions are taken to ensure that the surface is at least 5 C above the temperature of the surrounding air), there is moisture or ice visible on the substrate or if any of these conditions are likely to occur before the paint has dried. As far as possible, apply paint in the temperature range 15 C to 25 C. If temperatures fall outside the range of 10 C and 35 C do not paint unless paints with the necessary temperature tolerances have been specified. The Principal s representative may order painting to cease if, despite all conditions being met, there is a likelihood of frost or dew. The Contractor may propose protective measures against frost and these measures will be subject to the approval of the Principal s representative SEQUENCE OF OPERATIONS Painting work to generally follow the following sequence: Complete all surface preparation before commencing painting; Apply primers, sealers, stains, undercoats, paints and clear coatings in the sequences laid down by ; Allow the full drying time between coats laid down by ; Do not expose primers, undercoats and intermediate coats beyond a few days before applying the next coat. Refer to appropriate data sheets for recommended recoat times; Finish broad areas before painting trim; Ensure batch numbers of tins are matched for whole areas; Internally, paint ceilings before walls and walls before joinery, trim and other items APPLICATION Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 8.7 Methods of Application. Select brush, roller, pad or spray and apply coatings to the recommendations of to obtain a coating of the specified thickness, uniform gloss, surface finish and colour. Refer to the appropriate product data sheet and can label for appropriate application methods LIGHTLY SAND Lightly sand primers, sealers, undercoats and intermediate coats to remove dust pick-up, protruding fibres and coarse particles. Complete by removing dust immediately before applying the next coat DEFECTIVE WORK Immediately correct at own cost any defective work and recoat as required, following precisely the system being applied LOSS OR DAMAGE The Contractor shall be responsible for any loss or damage that may be caused to the property of the Owner in the carrying out of this contract. The Contractor shall make good such loss or damage at he Contractor s own expense, to the satisfaction of the Owner. 6711R RESENE PAINTING Page 11

12 3.26 EACH COAT Each coat of paint and the completed paint system to have the following qualities and properties: Uniform finish, colour, texture, sheen and hiding power and the proper number of coats applied; No blemishes such as runs, sags, crinkling, fat edges, entrained paint skins, hairs, dust, bare or starved patches, cracks, brush marks, ladder marks and blistering; Proper covering of corners, crannies, thin edges, cracks, end grains and other difficult places of application. Completion 3.27 CLEAN Clean all adjoining surfaces, glass and fittings of any paint contamination. Clean adjoining glass to a shining finish LEAVE Leave the whole of this work uniform in gloss and colour, of correct thickness, free from all painting defects, clean and unmarked and to the standard required for all following trades REMOVE Remove all dropsheets, coverings and masking to leave surrounding surfaces and areas clean, tidy and undamaged. Remove all debris, unused materials and elements from the site REPLACE Replace all hardware without damage to it or the adjoining surface and leave hardware properly fitted and in working order. 4. SCHEDULES Prepare surfaces and apply paints in accordance with the attached paint system specifications. 4.1 CONTROL SAMPLES Substrate One-Line number ~ ~ 4.2 SUPERVISED CONTROL SAMPLES Substrate One-Line number ~ ~ 4.3 INSPECTION OF THE WORK Coating System Inspection at completion of ~ ~ 4.4 HARDWARE Hardware for removal: ~ Paint system schedules 4.5 EXTERIOR FINISHES Substrate number Colour Weatherboards ~ Timber Joinery/Fascias/Barges Timber Deck Concrete Masonry 4.6 INTERIOR FINISHES Room name Number Substrate number Colour Living G02 Ceiling - Plasterboard ~ Exposed Rafters Walls - Plasterboard 6711R RESENE PAINTING Page 12

13 Trim - Timber Doors - Paint Finish Dining G03 Ceiling - Plasterboard Exposed Rafters Walls - Plasterboard Timber Panelling Trim - Timber Doors - Paint Finish 1e EXTERIOR CEMENTITIOUS SURFACES Prep Coat products Finish 1e 1.1 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 4 th Multishield + D54a (Optional) 1e 1.2 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 4 th Multishield + D54a (Optional) D83 TP Limelock D809 1 st SP Sonyx 101 D30 Waterborne semi-gloss 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 4 th Multishield + D54a (Optional) 1e 1.3 D83 TP Limelock D809 1 st SCS Concrete Primer D405 4 th Multishield + D54a (Optional) D83 TP Limelock D809 1 st SP Lumbersider D34 Waterborne satin 4 th Multishield + D54a (Optional) 1e 2.1 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 2e EXTERIOR TIMBERS Prep Coat products Finish 2e 1.1 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 2e 1.2 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 2 nd Sonyx 101 D30 Waterborne semi-gloss 6711R RESENE PAINTING Page 13

14 Prep Coat products Finish 3 rd Sonyx 101 D30 Waterborne semi-gloss 2e 1.3 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 D82 1 st SP Lumbersider D34 2e 2.1 D82 1 st NRS Quick Dry D45 TTS Wood Primer D40 HO Sureseal D42 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 2e EXTERIOR TIMBERS, STAINS AND CLEAR FINISHES Prep Coat products Finish 2e 3.5 D82 1 st Waterborne Woodsman D57a Waterborne flat 2 nd Waterborne Woodsman D57a Waterborne flat 3 rd Waterborne Woodsman D57a (after 3 months) 2e 4.5 D82 1 st Woodsman D57 Solventborne flat 2 nd Woodsman D57 Solventborne flat 3 rd Woodsman D57 (after 3 months) 3e EXTERIOR TIMBER JOINERY Prep Coat products Finish 3e 1.1 D82 & 1 st NRS Quick Dry D45 TimberLock TTS Wood Primer D40 D48 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss 3e 1.2 D82 & 1 st NRS Quick Dry D45 TimberLock TTS Wood Primer D40 D48 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss 3e 2.1 D82 & 1 st NRS Quick Dry D45 TimberLock TTS Wood Primer D40 D48 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 4e EXTERIOR TIMBER DECKS, PERGOLAS AND FENCES Prep Coat products Finish 4e 1.3 D82 1 st NRS Lumbersider D34 NSF Resitex Std D70 4e 3.5 D82 1 st SF Waterborne Woodsman D57a Waterborne flat 2 nd Waterborne Woodsman D57a Waterborne flat 3 rd Waterborne Woodsman D57a (after 3 months) 4e 4.5 D82 1 st Woodsman D57 Solventborne flat 2 nd Woodsman D57 Solventborne flat 3 rd Woodsman D57 (after 3 months) 4e 4.5 D D82 1 st Kwila Decking Stain D501 Solventborne flat 6711R RESENE PAINTING Page 14

15 Prep Coat products Finish 2 nd Kwila Decking Stain D501 Solventborne flat 5e EXTERIOR GALVANISED STEEL AND ZINCALUME Prep Coat products Finish 5e 1.1 D89 1 st NW Galvo-Prime D402 R Galvo One D41 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 5e 1.2 D89 1 st NW Galvo-Prime D402 R Galvo One D41 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 5e 1.3 D89 1 st NW Galvo-Prime D402 R Galvo One D41 5e 2.1 D89 1 st Galvo One D41 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 6e EXTERIOR FERROUS METALS Prep Coat products Finish 6e 1.1 D801 1 st Rust Arrest RA30 2 nd Rust Arrest RA30 3 rd Enamacryl D309 Waterborne gloss 4 th Enamacryl D309 Waterborne gloss 6e 1.2 D801 1 st Rust Arrest RA30 2 nd Rust Arrest RA30 3 rd Lustacryl D310 Waterborne semi-gloss 4 th Lustacryl D310 Waterborne semi-gloss 6e 2.1 D801 1 st NRS Rust Arrest RA30 2 nd Rust Arrest RA30 3 rd Acrylic Undercoat D404 4 th Super Gloss D32 Solventborne gloss 1 st HDS Alumastic RA402 2 nd Uracryl 403 RA56 Solventborne gloss 3 rd Uracryl 403 RA56 Solventborne gloss 6e 2.2 D801 1 st HDS Alumastic RA402 2 nd Uracryl 402 RA55 Solventborne semi-gloss 3 rd Uracryl 402 RA55 Solventborne semi-gloss 7e EXTERIOR NON-FERROUS METALS Prep Coat products Finish 7e 1.1 D89 1 st NRS Vinyl Etch RA31 WNW Galvo-Prime D402 2 nd Hi-Glo D31* Waterborne gloss 3 rd Hi-Glo D31* Waterborne gloss * For doors, windows and joinery, use Enamacryl D309 in place of Hi-Glo. 7e 1.2 D89 1 st NRS Vinyl Etch RA31 WNW Galvo-Prime D402 2 nd Sonyx 101 D30* Waterborne semi-gloss 3 rd Sonyx 101 D30* Waterborne semi-gloss * For doors, windows and joinery, use Lustacryl D310 in place of Sonyx e 1.3 D89 1 st NRS Vinyl Etch RA31 WNW Galvo-Prime D R RESENE PAINTING Page 15

16 Prep Coat products Finish 7e 2.1 D89 1 st NRS Vinyl Etch RA31 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss D89 1st HDF Vinyl Etch RA31 2nd Uracryl 403 RA56 Solventborne gloss 3rd Uracryl 403 RA56 Solventborne gloss 7e 2.2 D89 1 st Vinyl Etch RA31 2 nd Uracryl 402 RA55 Solventborne semi-gloss 3 rd Uracryl 402 RA55 Solventborne semi-gloss 7e 2.4 D89 1st Vinyl Etch RA31 2nd Uracryl 404 RA59 Solventborne low sheen 3rd Uracryl 404 RA59 Solventborne low sheen 8e EXTERIOR CEDAR Prep Coat products Finish 8e 1.1 D82 & 1 st NC Quick Dry D45 TimberLock WC Wood Primer D40 D48 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 8e 1.2 D82 & 1 st NC Quick Dry D45 TimberLock WC Wood Primer D40 D48 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 8e 1.3 D82 & 1 st NC Quick Dry D45 TimberLock WC Wood Primer D40 D48 D82 & 1 st SP Lumbersider D34 Waterborne satin T/Lock D48 8e 2.1 D82 & 1 st NC Quick Dry D45 TimberLock WC Wood Primer D40 D48 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 8e 3.5 D82 1 st SF Waterborne Woodsman D57a Waterborne flat 2 nd Waterborne Woodsman D57a Waterborne flat 3 rd Waterborne Woodsman D57a (after 3 months) 8e 4.5 D82 1 st SF Woodsman D57 Solventborne flat 2 nd Woodsman D57 Solventborne flat 3 rd Woodsman D57 (after 3 months) D82 1st KS Kwila Decking Stain D501 Solventborne flat 2nd Kwila Decking Stain D501 Solventborne flat 9e EXTERIOR TOTARA AND MATAI TIMBER ONLY Prep Coat products Finish 9e 1.1 D82 1 st Quick Dry D45 2 nd Hi-Glo D31* Waterborne gloss 3 rd Hi-Glo D31* Waterborne gloss 6711R RESENE PAINTING Page 16

17 Prep Coat products Finish 9e 1.2 D82 1 st Quick Dry D45 2 nd Sonyx 101 D30* Waterborne semi-gloss 3 rd Sonyx 101 D30* Waterborne semi-gloss 9e 1.3 D82 1 st NRS Quick Dry D45 D82 1 st SP Lumbersider D34 Waterborne satin 9e 2.1 D82 1 st Quick Dry D45 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 9e EXTERIOR TOTARA AND MATAI TIMBER, STAINS AND CLEAR FINISHES Prep Coat products Finish 9e 3.5 D82 1 st Waterborne Woodsman D57a Waterborne flat 2 nd Waterborne Woodsman D57a Waterborne flat 3 rd Waterborne Woodsman D57a (after 3 months) 9e 4.5 D82 1 st Woodsman D57 Solventborne Flat 2 nd Woodsman D57 Solventborne Flat 3 rd Woodsman D57 (after 3 months) 10e EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS Prep Coat products Finish 10e 1.1 D803 1 st Membrane Roofing Primer D49 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 10e 1.2 D803 1 st Membrane Roofing Primer D49 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 10e 1.3 D803 1 st NRS Membrane Roofing Primer D49 D803 1 st NSF Membrane Roofing Primer D49 2 nd Resitex (Std) D70 Waterborne texture 3 rd Resitex (Std) D70 Waterborne texture 11e GLASS, GLAZED TILES, BAKED ENAMEL SYSTEMS Prep Coat products Finish 11e 1.1 D802 or 1 st Smooth Surface Sealer D47 D803 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 11e 1.2 D802 or 1 st Smooth Surface Sealer D47 D803 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 11e 1.3 D802 or 1 st Smooth Surface Sealer D47 D R RESENE PAINTING Page 17

18 Prep Coat products Finish 11e 2.1 D802 or 1 st Smooth Surface Sealer D47 D803 2 nd 3 rd Super Gloss D32 Solventborne gloss 12e GLASS REINFORCED POLYESTER, EPOXY, PVC, ACRYLIC SHEETING, POLYSTYRENE, POLYCARBONATE Prep Coat products Finish 12e 1.1 D803 1 st Hi-Glo D31 Waterborne gloss 2 nd Hi-Glo D31 Waterborne gloss 12e 1.2 D803 1 st Sonyx 101 D30 Waterborne semi-gloss 2 nd Sonyx 101 D30 Waterborne semi-gloss 12e 1.3 D803 1 st Lumbersider D34 Waterborne satin 12e 2.1 D803 1 st Smooth Surface Sealer D47 2 nd 3 rd Super Gloss D32 Solventborne gloss 13e BRICK AND TERRACOTTA Prep Coat products Finish 13e 1.1 D802 1 st SSP Hi-Glo D31 Waterborne gloss 2 nd Hi-Glo D31 Waterborne gloss D802 1 st ES Sureseal D42 2 nd Hi-Glo D31 Waterborne gloss 3 rd Hi-Glo D31 Waterborne gloss 13e 1.2 D802 1 st SSP Sonyx 101 D30 Waterborne semi-gloss 2 nd Sonyx 101 D30 Waterborne semi-gloss D802 1 st ES Sureseal D42 2 nd Sonyx 101 D30 Waterborne semi-gloss 3 rd Sonyx 101 D30 Waterborne semi-gloss 13e 1.3 D802 1 st SSP Lumbersider D34 Waterborne satin D802 1 st ES Sureseal D42 13e 2.1 D802 1 st SSP Quick Dry D45 ES Sureseal D42 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 13e/i 3.1 D802 1 st IO Aquaclear D59 Waterborne gloss 2 nd Aquaclear D59 Waterborne gloss 3 rd Aquaclear D59 Waterborne gloss D802 SE Aquapel D65 1 st EI Multishield+ D54a Waterborne gloss 2 nd Multishield+ D54a Waterborne gloss 3 rd Multishield+ D54a Waterborne gloss 6711R RESENE PAINTING Page 18

19 Prep Coat products Finish 13e/i 4.1 D802 SE Aquapel D65 1 st NRS F.10 Glaze D56 Solventborne gloss 2 nd F.10 Glaze D56 Solventborne gloss 3 rd F.10 Glaze D56 Solventborne gloss D802 SE Aquapel D65 1 st HDS Uracryl 403 RA56 Solventborne gloss 2 nd Uracryl 403 RA56 Solventborne gloss 3 rd Uracryl 403 RA56 Solventborne gloss 13e/i 4.2 D802 SE Aquapel D65 1 st HDS Uracryl 402 RA55 Solventborne semi-gloss 2 nd Uracryl 402 RA55 Solventborne semi-gloss 3 rd Uracryl 402 RA55 Solventborne semi-gloss 13e/i 4.5 D802 1 st PS Aquapel D65 Solventborne flat 2 nd Aquapel D65 Solventborne flat 3 rd Aquapel D65 Solventborne flat 14e CLEAR FINISHES ON CLAY TILES, ABSORBENT TILES, STONE AND SLATE, DECORATIVE AGGREGATE FLOORING Prep Coat products Finish 14e/i 4.1 D802 SE Aquapel D65 1 st LDF F.10 Glaze D56 Solventborne gloss 2 nd F.10 Glaze D56 Solventborne gloss 3 rd F.10 Glaze D56 Solventborne gloss D802 SE Aquapel D65 1 st HDF Uracryl 403 RA56 Solventborne gloss 2 nd Uracryl 403 RA56 Solventborne gloss 3 rd Uracryl 403 RA56 Solventborne gloss D802 SE Aquapel D65 1 st IMC Polythane D53 Solventborne gloss 2 nd Polythane D53 Solventborne gloss 3 rd Polythane D53 Solventborne gloss 14e/i 4.2 D802 SE Aquapel D65 1 st HDF Uracryl 402 RA56 Solventborne semi-gloss 2 nd Uracryl 402 RA56 Solventborne semi-gloss 3 rd Uracryl 402 RA56 Solventborne semi-gloss 16e EXTERIOR CANVAS AND AWNINGS Prep Coat products Finish 16e 1.1 D803 1 st Hi-Glo D31 Waterborne gloss 2 nd Hi-Glo D31 Waterborne gloss 16e 1.2 D803 1 st Sonyx 101 D30 Waterborne semi-gloss 2 nd Sonyx 101 D30 Waterborne semi-gloss 16e 1.3 D803 1 st Lumbersider D34 Waterborne satin 16e 2.5 D803 1 st Aquapel D65 Solventborne flat 2 nd Aquapel D65 Solventborne flat 17e WATERPROOFING MEMBRANES Prep Coat products Finish 17e 1.2 T D83 TP Limelock D809 1 st Concrete Primer D405 SP Thixalon 5 D63 Waterborne semi-gloss 2 nd Thixalon 5 D63 Waterborne semi-gloss 6711R RESENE PAINTING Page 19

20 Prep Coat products Finish 3 rd Thixalon 5 D63 Waterborne semi-gloss 4 th Multishield+ D54a (optional) 17e 1.2 F D83 TP Limelock D809 1 st Concrete Primer D405 SP Flexicover E D64 Waterborne semi-gloss 2 nd Flexicover E D64 Waterborne semi-gloss 3 rd Flexicover E D64 Waterborne semi-gloss 4 th Lumbersider D34 (optional) 17e 1.4 D83 TP Limelock D809 1 st Concrete Primer D405 SP X-200 D62 Waterborne low sheen 2 nd X-200 D62 Waterborne low sheen 3 rd X-200 D62 Waterborne low sheen 4 th Multishield+ D54a (optional) 18e HEAVY DUTY FLOOR COATINGS Prep Coat products Finish 18e 1.5 B D83 1 st BS Blacktop D304 Waterborne flat Blacktop D304 (optional) 18e 1.5 T D83 1 st BS Membrane Roof Primer D49 CS Tennis Court Coating D303 GCS Smooth Surface Sealer D47 2 nd Tennis Court Coating D303 Waterborne flat 3 rd Tennis Court Coating D303 Waterborne flat 18e/i 2.1 U D83 1 st CS Armourcote 510 RA40* 2 nd Uracryl 403 RA56 Solventborne gloss 18e/I 2.2 D83 1 st CS Armourcote 510 RA40* 2 nd Uracryl 402 RA55 Solventborne semi-gloss 18e 4.5 D83 1 st CS Concrete Stain D58 Solventborne flat 2 nd Concrete Stain D58 Solventborne flat * Add Industrial SRG Grit to this coat for non-skid version. 19e ANTI GRAFFITI SYSTEMS Prep Coat products Finish 19e 2.1 CS D83 1 st Armourcote 510 RA40 2 nd Imperite 413 RA57 Pigmented 3 rd Imperite 390 RA57 Clear 19e 4.1 CS D83 1 st Imperite 390 RA57 Clear 2 nd Imperite 390 RA57 Clear 3 rd Imperite 390 RA57 Clear 19e 2.1 CA D83 1 st Armourcote 510 RA47 2 nd Uracryl 403 RA56 Pigmented 3 rd Uracryl 403 RA56 Pigmented 4 th Uracryl 403 RA56 Clear 19e 4.1 CA D83 1 st Uracryl 403 RA56 Clear 2 nd Uracryl 403 RA56 Clear 3 rd Uracryl 403 RA56 Clear 19e 2.1 PA D83 1 st Quick Dry D45 2 nd Quick Dry D45 3 rd Uracryl 403 RA56 Pigmented 4 th Uracryl 403 RA56 Pigmented 5 th Uracryl 403 RA56 Clear 6711R RESENE PAINTING Page 20

21 Prep Coat products Finish 19e 2.1 OS D83 1 st Smooth Surface Sealer D47 2 nd Imperite 413 RA57 Pigmented 3 rd Imperite 413 RA57 Pigmented 4 th Imperite 390 RA57 Clear 19e 2.1 OA D83 1 st Smooth Surface Sealer D47 2 nd Uracryl 403 RA56 Pigmented 3 rd Uracryl 403 RA56 Pigmented 4 th Uracryl 403 RA56 Clear 19e 2.1 TA D83 1 st Quick Dry D45 2 nd Quick Dry D45 3 rd Uracryl 403 RA56 Pigmented 4 th Uracryl 403 RA56 Pigmented 5 th Uracryl 403 RA56 Clear 19e 4.1 SA D83 1 st Uracryl 403 RA56 Clear over pigmented 19e 4.1 SA D83 1 st Imperite 390 RA57 Clear over pigmented 20e TEXTURED AND SPECIALIST COATINGS (INCLUDING HARDITEX) Prep Coat products Finish 20e 1.2 T D83 1 st TP Limelock D809 SCS Concrete Primer D405 SP Thixalon 5 D63 2 nd Thixalon 5 D63 Waterborne semi-gloss 3 rd Thixalon 5 D63 (Optional) 4 th Multishield+ D54a (Optional) 20e 1.2 F D83 TP Limelock D809 1 st SCS Concrete Primer D405 SP Flexicover E D64 2 nd Flexicover E D64 Waterborne semi-gloss 3 rd Flexicover E D64 (Optional) 4 th Lumbersider D34 or Multishield+ D54a (Optional pigmented) (Optional clear) 20e 1.3 RCM D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Lumbersider D34* 3 rd Resitex D70 Waterborne textured 4 th Multishield+ D54a (Optional) * For additional waterproofing, replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Resitex. 20e 1.3 RS D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Lumbersider D34* 3 rd Resitex D70 Waterborne textured 4 th Multishield+ D54a (Optional) * For additional waterproofing, replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Resitex. 20e 1.3 H D806 1 st Galvo Prime D402 (Spot prime) 2 nd X-200 D62 3 rd Resitex D70 Waterborne textured 4 th Multishield+ D54a (Optional) 20e/i 1.3 P D83 TP Limelock D809 1 st SCS Concrete Primer D405 CB Refer Rockcote Systems 2 nd Plastercote D72* Waterborne textured 6711R RESENE PAINTING Page 21

22 Prep Coat products Finish 3 rd Plastercote D72 Waterborne textured 4 th Multishield+ D54a (Optional) * This coat of Plastercote can be replaced with one coat of Sandtex if desired. Some applicators may find Sandtex easier to apply 20e 1.5 D83 TP Limelock D809 1 st PC Aquapel D65 SSP AquaShield D601 Waterborne textured 2 nd AquaShield D601 Waterborne textured 3 rd AquaShield D601 Waterborne textured 20e/i 1.5 D83/ TP Limelock D809 D84 1 st SCS Concrete Primer D405 2 nd Lumbersider D34* 3 rd Sandtex D71 Waterborne textured * For additional waterproofing, replace this coat with one coat of X-200; for a higher DFT, replace this coat with one coat of Sandtex. 20e/i 1.5 D83/ TP Limelock D809 D84 1 st SP Lumbersider D34 2 nd Sandtex D71 Waterborne textured 3 rd Sandtex D71 Waterborne textured 21e PAINT EFFECTS Prep Coat products Finish 21e/i 1.5 C 1 st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3 rd Paint Effects Medium D307 Waterborne Flat - colourwashing 21eli 1.5 R 1st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3rd Paint Effects Medium D307 Waterborne Flat - ragging 21eli 1.5 S 1 st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3 rd Paint Effects Medium D307 Waterborne Flat - sponging 21eli 1.5 L 1 st IO Zylone Sheen x 2 D302 E Lumbersider x 2 D34 EWM X-200 x 2 D62 TF Resitex x 2 D70 3 rd Paint Effects Medium D307 Waterborne Flat - limewash effect 22e EXTERIOR MILD STEELS, NEW FERROUS METALS (MEDIUM AND LONG-TERM PROTECTION) Prep Coat products Finish 22e 2.1 EMT D st MT Zincilate 10 RA20 Inorganic zinc D801.8 D nd Armourcote 512 RA407 High build epoxy gloss 22e 2.2 EMT D801.1 D801.8 D st MT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy semi-gloss 6711R RESENE PAINTING Page 22

23 22e 2.1 UMT D801.1 D801.8 D801.7 Prep Coat products Finish 1 st MT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 403 RA56 Acrylic urethane gloss 22e 2.1 ELT D801.1 D801.8 D st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 512 RA407 High build epoxy gloss 22e 2.1 ULT D801.1 D801.8 D e 2.2 UMT D801.1 D801.8 D st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 403 RA56 Acrylic urethane gloss 1 st MT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 402 RA55 Acrylic urethane semi-gloss 22e 2.2 ELT D801.1 D801.8 D st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy semi-gloss 22e 2.2 ULT D801.1 D801.8 D e 2.3 MFMT D801.1 D801.8 D e 2.3 MFLT D801.1 D801.8 D e 2.4 UMT D801.1 D801.8 D e 2.4 ULT D801.1 D801.8 D st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 402 RA55 Acrylic urethane semi-gloss 1 st MT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Imperite IF 503 Metallic RA81 Acrylic epoxy satin metallic 1 st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Imperite IF 503 Metallic RA81 Acrylic epoxy satin metallic 1 st MT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 404 RA59 Acrylic urethane low sheen 1 st LT Zincilate 10 RA20 Inorganic zinc 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 404 RA59 Acrylic urethane low sheen 23e EXTERIOR NEW HOT DIPPED GALVANISED MILD STEEL (MEDIUM AND LONG-TERM PROTECTION) Prep Coat products Finish 23e 2.1 ELT D st LT Vinyl Etch RA31 Etch primer D nd Armourcote 512 RA407 High build epoxy gloss 23e 2.1 ULT D89.1 D st LT Vinyl Etch RA31 Etch primer 6711R RESENE PAINTING Page 23

24 Prep Coat products Finish 2 nd Armourcote 510 RA40 High build epoxy 3rd Uracryl 403 RA56 Acrylic urethane gloss 23e 2.2 ELT D89.1 D e 2.2 ULT D89.1 D e 2.3 MFLT D89.1 D e 2.4 ULT D89.1 D st LT Vinyl Etch RA31 Etch primer 2 nd Armourcote 510 RA40 High build epoxy semi-gloss 1 st LT Vinyl Etch RA31 Etch primer 2 nd Armourcote 510 RA40 High build epoxy acrylic urethane semi-gloss 3 rd Uracryl 402 RA55 1 st LT Vinyl Etch RA31 Etch primer 2 nd Armourcote 510 RA40 High build epoxy 3 rd Imperite IF 503 Metallic RA81 Acrylic epoxy satin metallic 1 st LT Vinyl Etch RA31 Etch primer 2 nd Armourcote 510 RA40 High build epoxy 3 rd Uracryl 404 RA59 Acrylic urethane low sheen 24e EXTERIOR NEW METAL SPRAY COATINGS (METAL ARC OR ZINC SPRAY) (MEDIUM AND LONG-TERM PROTECTION) Prep Coat products Finish 24e 2.1 ULT * 1 st LT Armourcote 220 RA34 Epoxy primer 2 nd Uracryl 403 RA56 Acrylic urethane 3 rd Uracryl 403 RA56 Acrylic urethane 4 th Uracryl 403 UVS Clear RA56 Acrylic urethane clear gloss 24e 2.2 ULT * 1 st LT Armourcote 220 RA34 Epoxy primer 2 nd Uracryl 402 RA55 Acrylic urethane 3 rd Uracryl 402 RA55 Acrylic urethane 4 th Uracryl 402 UVS Clear RA55 Acrylic urethane clear semigloss 24e 2.4 ULT * 1 st LT Armourcote 220 RA34 Epoxy primer 2 nd Uracryl 404 RA59 Acrylic urethane 3 rd Uracryl 404 RA59 Acrylic urethane 4 th Uracryl 404 UVS Clear RA59 Acrylic urethane clear low sheen * Refer to the Engineered Coating Systems manual for preparation 25e EXTERIOR METALLIC FINISHES Prep Coat products Finish Metallic finish on cementitious plaster 25e 1.3/5 D83 1 st Quick Dry D45 3 rd Enamacryl Metallic D309a Waterborne metallic 4 th Enamacryl Metallic D309a Waterborne metallic 5 th Multishield+ D54a (Optional) 25e 1.3/5P D83 1 st Quick Dry D45 4 th Pearl Shimmer D312 Waterborne pearlescent 5 th Multishield+ D54a (Optional) Metallic finish on concrete floor 25e 2.3/5 D83 1 st Armourcote 510 RA40 2 nd Imperite IF 503 RA81 Solventborne metallic 3 rd Uracryl 400 Series Clear Acrylic urethane 1i INTERIOR CEMENTITIOUS SURFACES 6711R RESENE PAINTING Page 24

25 Prep Coat products Finish 1i 1.1 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Enamacryl D309 Waterborne gloss 3 rd Enamacryl D309 Waterborne gloss 1i 1.2 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss D83 1 st SP Lustacryl D310 Waterborne semi-gloss 2 nd Lustacryl D310 Waterborne semi-gloss 3 rd Lustacryl D310 Waterborne semi-gloss 1i 1.3 D83 TP Limelock D809 1 st SCS Concrete Primer D405 D83 1 st SP Lumbersider D34 Waterborne satin 1i 1.4 ZS D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Zylone Sheen D302 Waterborne low sheen 3 rd Zylone Sheen D302 Waterborne low sheen D83 1 st SP Zylone Sheen D302 Waterborne low sheen 2 nd Zylone Sheen D302 Waterborne low sheen 3 rd Zylone Sheen D302 Waterborne low sheen 1i 1.4 SC D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Zylone SpaceCote D311 Waterborne low sheen 3 rd Zylone SpaceCote D311 Waterborne low sheen D83 1 st SP Zylone SpaceCote D311 Waterborne low sheen 2 nd Zylone SpaceCote D311 Waterborne low sheen 3 rd Zylone SpaceCote D311 Waterborne low sheen 1i 1.5 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Zylone 20 D37 Waterborne flat 3 rd Zylone 20 D37 Waterborne flat D83 1 st SP Zylone 20 D37 Waterborne flat 2 nd Zylone 20 D37 Waterborne flat 3 rd Zylone 20 D37 Waterborne flat 1i 2.1 D83 TP Limelock D809 1 st SCS Concrete Primer D405 2 nd Acrylic Undercoat D404 3 rd Super Gloss D32 Solventborne gloss 6711R RESENE PAINTING Page 25