CROSSING PLANKS SHALL BE SOFTWOOD MIN. 6096mm (20') LONG PLANKS ENDS TO BE BEVELED (SEE DETAIL1)

Transcription

1 TOP OF CROSSING BEVEL TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF CROSSINGS TO HVE SUITBLE PPROCHES ON EITHER SIDE WITH DEQUTE SIGHTLINES MIN. 508 (TYPICL) C L CROSSING CROSSING PLNKS SHLL BE SOFTWOOD MIN. 6096mm (0') LONG PLNKS ENDS TO BE BEVELED (SEE DETIL) PPROCHES TO TO BE BOX NCHORED T EVERY TIE FOR 6m (00') IN EITHER DIRECTION, WHERE NCHORS RE REMOVED TO FCILITTE THE INSTLLTION OF PLNK SIZE RIL WEIGHT (PLNK HEIGHT) mm 00 lb. 5 (6") 5 lb. 78 (7") 36 lb. 78 (7") OR 03 (8") 304.8mmx.7mm ("x/") LG PLNKS ENDS TO BE BEVELED T 30 (H=.7, V=.0) X /" LG SHLL BE USED PER PLNK. LG SCREWS SHLL BE STGGERED BETWEEN ECH PLNK TO VOID SPLITTING THE TRCK TIE. SEE GTTS REV 0 PGE 5/457 ITEM 6.D. 57mm (0 3/8") (TYPICL) FILTER FBRIC 30 LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF PLN SCLE :50 GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) DETIL SCLE :0 BLLST FLNGEWY FILLER BLOCK (TYPICL) GRNULR MTERIL (TYPICL) 304.8mmx.7mm ("x/") LG MIN. 47.6mm ( 7/8") FLNGEWY DEPTH ( ") 54 ( 0") CROSSING PLNKS TOP OF CROSSING SHLL NOT EXCEED 5.4mm (") BOVE OR BELOW THE TOP OF RIL MIN mm ( 5/8"), MX (4 3/4") FLNGEWY WIDTH FINISHED TOP OF GRNULR TO MTCH TOP OF CROSSING PLNKS. TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITION ND TO THE STISFCTION ND PPROVL OF THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 4. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED. T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDES BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY 5. PLNKING MUST BE REMOVED T LEST NNULLY, FOR THOROUGH TRCK INSPECTION, ND TO COMPLETE NY REPIRS REQUIRED UNLESS OTHERWISE DIRECTED BY THE CM MNGER TRCK. 6. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. FILTER FBRIC FILTER FBRIC BLLST SCLE :0

2 # HRDWOOD TIE 5 X 03 X 59mm CROSSINGS TO HVE SUITBLE PPROCHES ON EITHER SIDE WITH DEQUTE SIGHTLINES TOP OF CROSSING BEVEL TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF MIN. 508 (TYPICL) C L CROSSING CROSSING PLNKS SHLL BE SOFTWOOD MIN. 6096mm (0') LONG PLNKS ENDS TO BE BEVELED (SEE DETIL) PLNK SIZE RIL WEIGHT (PLNK HEIGHT) mm 00 lb. 5 (6 ") 5 lb. 78 (7 ") 36 lb. 78 (7") OR 03 (8") 304.8mmx.7mm ("x/") LG PLNKS ENDS TO BE BEVELED T 30 (H=.7, V=.0) 30 6" X /" LG SHLL BE USED PER PLNK. LG SCREWS SHLL BE STGGERED BETWEEN ECH PLNK TO VOID SPLITTING THE TRCK TIE. SEE GTTS REV 0 PGE 5/457 ITEM 6.D. 60mm (4") (TYPICL) FILTER FBRIC # HRDWOOD TIE 5 X 03 X 59mm DETIL SCLE :0 8" BLLST LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF 304.8mmx.7mm ("x/") LG MIN. 48mm ( 7/8") FLNGEWY DEPTH FLNGEWY FILLER BLOCK (TYPICL) GRNULR MTERIL (TYPICL) PLN SCLE : (") 54 (0") GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CROSSING PLNKS MIN. 67mm ( 5/8"), MX. 0 (4 3/4") FLNGEWY WIDTH CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) TOP OF CROSSING SHLL NOT EXCEED 5.4mm (") BOVE OR BELOW THE TOP OF RIL FINISHED TOP OF GRNULR TO MTCH TOP OF CROSSING PLNKS. TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITIONND TO THE STISFCTION ND PPROVL O THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 4. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDE BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY. 5. UPON REMOVL OF THE STEEL TIES MUST BE FULLY SURFCED WITH MECHNICL TMPER. SUPPLY SUFFICIENT BLLST TO RESTORE BLLST PRISM ND BLLST IN THE CRIBS S PER MX STNDRDS. 6. PLNKING MUST BE REMOVED T LEST NNULLY, FOR THOROUGH TRCK INSPECTION, ND TO COMPLETE NY REPIRS REQUIRED UNLESS OTHERWISE DIRECTED BY THE CM MNGER TRCK. 7. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. FILTER FBRIC BLLST SCLE :0 FILTER FBRIC # HRDWOOD TIE 5 X 03 X 59mm

3 CROSSINGS TO HVE SUITBLE PPROCHES ON EITHER SIDE WITH DEQUTE SIGHTLINES TOP OF CROSSING BEVEL TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF MIN. 508 (TYPICL) C L CROSSING # HRDWOOD TIE 5 X 03 X 59mm CROSSING PLNKS SHLL BE SOFTWOOD MIN. 6096mm (0') LONG PLNKS ENDS TO BE BEVELED (SEE DETIL) PLNK SIZE RIL WEIGHT (PLNK HEIGHT) mm 00 lb. 5 (6") 5 lb. 78 (7") 36 lb. 78 (7") OR 03 (8") 304.8mmx.7mm ("x/") LG PLNKS ENDS TO BE BEVELED T 30 (H=.7, V=.0) 30 X /" LG SHLL BE USED PER PLNK. LG SCREWS SHLL BE STGGERED BETWEEN ECH PLNK TO VOID SPLITTING THE TRCK TIE. SEE GTTS REV 0 PGE 5/457 ITEM 6.D. 60mm (4") (TYPICL) FILTER FBRIC # HRDWOOD TIE 5 X 03 X 59MM DETIL SCLE :0 BLLST LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF 304.8mmx.7mm ("x/") LG MIN. 48mm ( 7/8") FLNGEWY DEPTH FLNGEWY FILLER BLOCK (TYPICL) GRNULR MTERIL (TYPICL) PLN SCLE : (") 54 (0") GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CROSSING PLNKS MIN. 67mm ( 5/8"), MX. 0 (4 3/4") FLNGEWY WIDTH CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) TOP OF CROSSING SHLL NOT EXCEED 5.4mm (") BOVE OR BELOW THE TOP OF RIL FINISHED TOP OF GRNULR TO MTCH TOP OF CROSSING PLNKS. TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITION ND TO THE STISFCTION ND PPROVL OF THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. SKEWED TIES SHLL BE DJUSTED BY N PPROVED TRCK CONTRCTOR 4. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 5. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED. T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDES BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY. 6. PLNKING MUST BE REMOVED T LEST NNULLY, FOR THOROUGH TRCK INSPECTION, ND TO COMPLETE NY REPIRS REQUIRED UNLESS OTHERWISE DIRECTED BY THE CM MNGER TRCK. 7. UPON REMOVL OF SUPPLY SUFFICIENT BLLST TO RESTORE BLLST PRISM ND BLLST IN THE CRIBS S PER MX STNDRDS. 8. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. FILTER FBRIC BLLST SCLE :0 FILTER FBRIC # HRDWOOD TIE 5 X 03 X 59mm

4 END OF CROSSING TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF MIN 508mm (0") (TYPICL) C CROSSING L SURFCE DESIGN 0" X 3/4" LGS COUNTERSUNK WITH PLUGS (REFER TO DETIL ) CROSSING PPROCHES TO BE BOX NCHORED T EVERY TIE FOR MINIMUM OF THREE (3) TIES IN EITHER DIRECTION RUBBER PNNEL /" Ø X 3" LG HEX HED LG SCREW WOOD TIES DETIL SCLE :0 RUBBER PLUG (NOTE 5).5" LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF GRNULR MTERIL (TYPICL) FIELD PD (TYPICL) RUBBER PLUG (DETIL ) GRNULR MTERIL (TYPICL) PLN SCLE :50 94mm (36") RUBBER PNNEL (TYPICL) EXISTING HOLES MNUFCTURE PRE-DRILLED (TYPICL) Part # Part # Part # 57mm (0 3/8")(TYPICL) RUBBER PNEL NEW HOLES FIELD DRILLED (TYPICL) GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) TOP OF CROSSING SHLL NOT EXCEED 5.4mm (") GUGE PD BOVE OR BELOW THE TOP OF RIL 56 /" TONGUE OR GROOVE (TYPICL) 0" 0" " DETIL SCLE :.75". TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITION ND TO THE STISFCTION ND PPROVL OF THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. WOOD TIE CENTER TO CENTER SPCING SHLL BE PROVIDED ND DJUSTED IN THE FIELD BY N PPROVED TRCK CONTRCTOR. 4. IF REQUIRED, HOLES TO SECURE PNELS TO THE TIES SHLL BE FIELD DRILLED TO CCOMMODTE EXISTING TIE SPCING ND LGS S SHOWN. 5. PNEL MODIFICTION SHLL BE S PER MNUFCTURER RECOMMENDTIONS ND UPON METROLINX PPROVL. 6. RUBBER PLUG TO BE SUPPLIED BY MNUFCTURE OF RUBBER PNNES. 7. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 8. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED. T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDES BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY 9. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. BLLST FILTER FBRIC WOOD TIE SCLE :0

5 CENTER FIELD SDDLE END OF CROSSING TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF MIN 508mm (0") (TYPICL) C CROSSING L CENTER GUGE SDDLES SURFCE DESIGN RUBBER PNNEL STEEL TIES DETIL SCLE :0 RUBBER CROSSING MTERIL C ROD L BRCKET GRNULR MTERIL (TYPICL) RUBBER PNEL 94mm (36") RUBBER PNNEL (TYPICL) CENTER FIELD SDDLE 60mm (4") (TYPICL) DETIL STBILIZER LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF PLN SCLE :50 GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) /8" PIN, /" LONG 304 GRDE STINLESS STEEL GRNULR MTERIL (TYPICL) FIELD PD (TYPICL) FILTER FBRIC BLLST SCLE :0 56 /" GUGE PD STBILIZER ROD (TYPICL) TONGUE OR GROOVE (TYPICL) STEEL TIE. TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITION ND TO THE STISFCTION ND PPROVL OF THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 4. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED. T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDES BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY. 5. UPON REMOVL OF THE STEEL TIES MUST BE FULLY SURFCED WITH MECHNICL TMPER. 6. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. 0 GUGE 304 GRDE STINLESS STEEL CENTER SDDLE

6 CENTER FIELD SDDLE END OF CROSSING TO BE OFFSET MIN. 508mm (0") FROM THE EDGE OF MIN 508mm (0") (TYPICL) C CROSSING L CENTER GUGE SDDLES SURFCE DESIGN RUBBER PNNEL CONCRETE TIES DETIL SCLE :0 RUBBER CROSSING MTERIL GRNULR MTERIL (TYPICL) RUBBER PNEL 94mm (36") RUBBER PNNEL (TYPICL) CENTER FIELD SDDLE 60mm (4") (TYPICL) C ROD L DETIL BRCKET STBILIZER /8" PIN, /" LONG 304 GRDE STINLESS STEEL LOCKBLE DOUBLE SWING GTE (OPSD 97.0) OR OTHER LOCKBLE TYPE GTE TO BE INSTLLED ON BOTH SIDES OF GTE TO BE CONSTRUCTED MOVEMENT OF THE GTE INTO THE RIGHT OF WY CHIN LINK FENCE TO BE INSTLLED WHERE PPLICBLE (OPSS 77) PLN SCLE :50 0 GUGE 304 GRDE STINLESS STEEL GRNULR MTERIL (TYPICL) FIELD PD (TYPICL) BLLST FILTER FBRIC SCLE :0 56 /" GUGE PD TONGUE OR GROOVE (TYPICL) CONCRETE TIE STBILIZER ROD (TYPICL). TEMPORRY CONSTRUCTION CROSSINGS SHLL BE INSTLLED IN CCORDNCE WITH GO TRNSIT TRCK STNDRDS, RC-0506, 0TRK, LTEST EDITION ND TO THE STISFCTION ND PPROVL OF THE CORRIDOR MINTENNCE SENIOR MNGER OF TRCK ND STRUCTURES.. NO RIL JOINTS THROUGH,RIL MUST BE WELDED. 3. USE OF TO BE PROTECTED T LL TIMES BY RILWY TRCK PROTECTION FOREMN. 4. BRRIER TO GUIDE CONSTRUCTION TRFFIC ND TO DETER TRESPSSERS SHLL BE PROVIDED. T MINIMUM, THE BRRIER SHLL CONSIST OF LOCKBLE GTE THT IS FLNKED ON BOTH SIDES BY CONCRETE ND/OR FENCING BRRIERS THT EXTEND FROM THE GTE TO THE LIMITS OF RILWY PROPERTY. 5. GRNULR SHLL BE USED IN TRNSITION FROM THE CONSTRUCTION CCESS TO THE TOP OF THE TEMPORRY WOOD PLNKING, THE FILTER FBRIC SHLL EXTEND TO THE OUTSIDE EDGE OF THE GRNULR TO PREVENT THE EXISTING BLLST FROM ERODING ND CONTMINTING. CENTER SDDLE