E P CONCRETE BLOCK SEALER

Transcription

1 earth friendly chemistry E P CONCRETE BLOCK SEALER E P latest waterproofing product. Utilising advanced ACRYLIC technology, combined with Polyester Polymer. This formula outperforms all other aliphatic solutions currently in the market place. This latest product was specially developed for Concrete Blocks used in retaining wall construction. Some benefits are:- High surface tension easier stain removal properties Two applications Non toxic non hazardous non flammable High chemical resistance Prevents fretting mortar Compatible with all conventional sealants, adhesives & paint Penetrates & protects from within. *Colour Milky White *State Liquid *Vapour (Air + 1) N/A *Specific Gravity: (Water = 1) 1.34@ 20 Degrees C. *Solubility in Water: Dilutable *Evaporation Rate: (BAC = 1) : Same as water. *Percent Volatile by Weight: N/A *ph: 7.0 *Boiling Point: 100 degrees Celsius. Water *Freezing Point: 0 degrees Celsius. Water Theoretical Coverage: 4-5 M2 per litre Method: Hand or Mechanical Sprayer. Consists of : 5, 20 and 200 Litre drum Shelf Life: 12 months minimum from date of manufacture when maintained in protected 5 38 degrees Celsius Enviropacific Pty Ltd 2/207 Bank Street Welshpool Perth Western Australia 6106 tel: fax: enviropacific@oz .com web:

2 E P CONCRETE BLOCK SEALER Is not a Surface coating. Delivers easy cleaning and high tension for all surfaces Does NOT aerate. Insulates, hardens and waterproofs concrete blocks Causes a chemical reaction that solidifies the component parts of concrete and masonry into one single mass. Increases the tensile strength and prevents concrete from surface cracking, crumbling, dusting and rutting. Increasing the wearing quality. Enviropacific recommends Urethane sealers for floor and ceiling construction Joins

3 earth friendly chemistry Application Instructions 1. Apply EP Concrete Block Sealer once structure has been surveyed for any repairs required. 2. Use a low-pressure sprayer (Back -pack type) or any spray, operated at no more than 20 Psi. 3. Spray entire surface area using approximately 1 Litre per 4 5 m2 apply second coat within 30 to 45 mins. if required. 4. Critical that any missing mortar and cracks are repaired prior to sealing we recommend EP Bondex used in repair mortar. E P Concrete Block Sealer is best applied by spray method; this is not only fast and effective but also gives the correct application rate. Allow several days for completion of curing process and penetration. Allow to dry completely prior to the application of paint if that is desired. EP Concrete Block Sealer will provide a long lasting, problem free bond for paints, prevents peeling, blistering and cracking. E P Concrete Block Sealer will not harm glass, tile or aluminium.

4 For the Paint Trade EP Concrete Block Sealer will prevent and solve the age-old problem, which normally occurs whenever masonry is painted. Due to porosity of all masonry such as render, concrete, brick and terrazzo and its chemical composition, a long lasting surface bond with any surface coating is questionable and sometimes impossible. EP Concrete Block Sealer prevents Saponification so all paints last even longer than specified also paint is easier to apply and will achieve maximum m2 coverage.

5 Specifications 1 PRODUCT : EP Concrete Block Sealer 2. MANUFACTURER: Enviropacific Pty Ltd 2/207 Bank Street Welshpool Perth Western Australia 6106 tel: fax: enviropacific@oz .com web: 3. PRODUCT DESCRIPTION: EP Concrete Block Sealer is a non-toxic, non-caustic, non-flammable inorganic formulation with no equal. It permanently waterproofs and preserves. 4. PRODUCT USES: For industrial, commercial, and residential use, on concrete block work. For homes, warehouses, commercial buildings, factories. 5. JOB LIMITATIONS: Apply in good weather when air and surface temperature are above 7 Degrees Celsius. Temperature must remain above 7 Degrees Celsius for 24 hours after application. For optimum application properties, materials should be between 15 to 28 Degrees Celsius prior to application. Maintain unused material in closed containers in protected storage at 4 to 38 Degrees Celsius. 6. SURFACE APPLICATION: DO NOT STORE IN DIRECT SUNLIGHT. Good surface preparation is essential to a satisfactory coating. Surfaces to be coated should be clean and dry. Remove all dirt, dust, oil, grease, rust, mildew and loose or cracked paint or other contamination by first cleaning with EP Cleaning Products. Rinse thoroughly and allow to dry.

6 NOTICE EP Concrete Block Sealer should not be applied to any surface that has had a previous coating of silicone, siloxene or solvent-based material. EP Concrete Block Sealer IS A PENETRATING PRODUCT. If the applicator sees that is not being Absorbed. It should not be applied.

7

8

9

10

11

12

13

14

15

16