GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM
|
|
- Meghan Nash
- 6 years ago
- Views:
Transcription
1 1 GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials, and services to furnish and install VERSA SHIELD Window Screens and correlated components as specified herein and as shown by drawings RELATED WORK A. Section Aluminum Entrance and Storefronts B. Section Aluminum Windows C. Section Wood Windows D. Section Glass & Glazing 1.03 REFERENCES A. ANSI/SMA B. City of New York Department of Health Window Falls Prevention Program 1.04 TESTING AND PERFORMANCE REQUIREMENTS A. Testing 1. Test Units - All tests, unless otherwise noted, shall conform to the ANSI/SMA requirements for a Heavy 100 foot pound impact rating and the City of New York Department of Health Falls Prevention Program. All tests to be completed and Product Approval certification received prior to bid date. Any deviation from such will not be accepted. 2. Test Procedures and Performance - a. ANSI/SMA ) Position and release pendulum system that when pulled back and released creates 50 foot pound force impact when striking the exterior center of the screen without failure. 2) Position and release pendulum system that when pulled back and released creates 100 foot pound force impact when striking the exterior center of the screen without failure. b. City of New York Department of Health Window Falls Prevention Program 1) Apply 150lb force at the center of the unit without failure 2) Apply 150lb force at the top of the unit without failure
2 2 B. 24 Hour Security Protection 1. Units must provide security protection. 2. Units must be in place 24hrs a day. 3. Units so designated must have emergency egress option. C. Sun Control 1. Units so designated to have a shading coefficient of up to Units so designated will have the ability to reduce solar heat gain by an estimated 50%. 3. The above requirements must be certified by an independent solar testing facility. D. E.M.I. Shielding Effectiveness 1. Units so designated to have a shielding effectiveness per the Dash, Straus & Goodhue study. 2. Units so designated and with the standard wool pile removed per specific project application shall have a shielding effectiveness of a least 93.69% attenuation effectiveness, when a tightly sealed electrical contact is made. 3. Units so designated and with the standard wool pile removed per specific project application shall have a shielding effectiveness of 24dB attenuation effectiveness, when a tightly electrical seal is made QUALITY ASSURANCE A. General 1. All components must be assembled / manufactured at an ISO certified facility. 2. Provide ANSI/SMA test results. 3. Provide City of New York Window Falls Prevention Program certification SUBMITTALS A. Shop Drawings 1. Manufacturer shall supply completed shop drawings, location, diagrams and necessary details and erection notes to insure a proper installation. B. Samples 1. Submit samples of each required aluminum and steel finishes. 2. Submit additional samples as may be directed by the architect. C. Test Reports 1. Provide certified independent laboratory test reports verifying compliance with requirements in Section DELIVERY, STORAGE AND HANDLING A. Instructions 1. Handle and store shutters and accessories in strict compliance with the manufacturer s specific instructions.
3 WARRANTIES A. VERSA SHIELD 1. Materials for the above project will be free from factory defects in materials and workmanship for a three (3) year limited warranty. 2. The contractor shall assume the full responsibility for one year on the proper usage, design, handling, installation and anchorage as it relates to the structural attachment as outlined on the approved shop drawings and specifications Materials PART 2: PRODUCTS A. Acceptable Window Manufacturers 1. EXETER ARCHITECTURAL PRODUCTS INC. Series VERSA SHIELD 242 W. Eighth Street Wyoming PA or Fax: B. Aluminum 1. Extruded aluminum shall be 6063-T5 alloy and temper measuring 1.0 wide by 5/16 deep. 2. Nominal wall thickness for primary frame extrusions shall be a minimum of Nominal wall thickness for Versa-Shield surround shall be a minimum of.045. C. Steel 1. Galvannealed steel sheet shall be of 950 XK Structural Steel. Mill finish quality, domestic material. Material certification required. 2. Stainless Steel sheet shall be 304-2b Prime conforming to ASTM-A Perforated metal sheet shall be of not more than 14 gauge and not less then 18 gauge galvannealed or stainless steel sheet. 4. Perforated pattern shall be InvisiPerf#1(TXL-22) or InvisiPerf #2 (TXL-23). Perforated sheet barrier pattern shall consist of staggered round holes, not to exceed 3/16 in diameter. Straight line hole patterns shall not be accepted. 5. Hole burrs on underside shall be minimal and not exceed.006 to maintain smoothness of sheet. 6. Perforated metal sheet shall have not less than 51% open air. D. Hardware 1. Vertically sliding units so designated to have spring loaded emergency egress barrel bolts mounted to the interior side of the unit at the sill, or optional single emergency egress latch. 2 Horizontally sliding units so designated to have two spring loaded emergency egress pull-latches mounted to the interior side of the unit at the jambs. 3 Vertically sliding units to have multiple stops to keep the barrier stationary.
4 4 4 Units designated as fixed windows to have maintenance-access custodial locks, allowing the windows to be cleaned and/or building maintenance performed. E. Anchors and Anchor Fasteners 1. Non-concealed anchors and tamper proof anchor fasteners may be of aluminum, stainless steel (300 series type), cadmium, zinc, nickel plated steel, brass and hot dipped galvanized. Non-treated corrosive fasteners are strictly prohibited. F. Bug Screen 1. 18x16 Fiberglass Mesh Bug Screen 2. Must be pulled tight to perforated metal infill to prevent damage, rips, tears, etc. 3. Secured with.187 spline 4. Installed by manufacturer 2.02 FABRICATION A. General 1. Depth of Versa-Shield surround shall be no more than 5/ Horizontal and vertical site lines shall be equal and not exceed 1 B. Frame 1. The Versa-Shield surround shall be made from extruded aluminum 6063-t5 alloy and temper measuring 1.0 wide by 5/16 deep with a minimum wall thickness of.045. Units so designated as operable to be encapsulated in 1.0 deep sliding frame pockets no less than.10 thick 2. The corners of the frame shall be precision mitered and fitted with four corner keys to aid in anti-torsion. 3. The Versa-Shield surround shall have a ridged groove measuring.430 long on the interior of the extrusion to tightly secure and encapsulate the perforated metal infill. 4. The Versa-Shield surround shall have a smooth grove running the entire length of the extrusion will allow for the use of anti-vibration wool piling. 5. The Versa-Shield surround shall have an interior slot for the installation of bug screening and spline. C. Finish - Aluminum (Select Organic or Anodic) 1. Organic - Finish all exposed areas of aluminum framing and components in accordance with AAMA or DESIGNATION DESC. AAMA SPEC AA-M12-C41-RIX Polycron III AA-M12-C41-RIX Kynar Based ANODIC - Finish all exposed areas of aluminum framing and components in accordance with AAMA DESIGNATION CLASS DESC. AAMA SPEC AA-M12-C22-A41 I Clear Anodized 607.1
5 5 *Color to be selected by architect. D. Finish Two step marine grade powder coating finishing process for Perforated Galvannealed Steel Sheet 1. Zinc Epoxy Thermosetting Primer Coating a. All oil, grease, scale, and rust must be removed prior to pretreatment. b. Film thickness must be mils baked to a smooth finish. c. Cure schedule is 10 minutes at 375 F peak metal temperature. d. Salt spray resistance per ASTM B 177 must be greater than hours with less than 1/8 creepage and no blistering. 2. Black Product # PRPL98019 Polyester Thermosetting Powder Coating. a. All oil, grease, scale, and rust must be removed prior to applying finish. b. Film thickness must be mils baked to a smooth finish c. Cure schedule is 10 minutes at 340 F peak metal temperature. d. Salt spray resistance per ASTM B 177 must be greater than hours with less than 1/8 creepage and no blistering e. 60% gloss E. Finish Three step marine grade powder coating finishing process for Perforated Stainless Steel Sheet 1. Chemical or Abrasive Passivation process prior to coating 2. Zinc Epoxy Thermosetting Primer Coating a. All oil, grease, scale, and rust must be removed prior to pretreatment. b. Film thickness must be mils baked to a smooth finish. c. Cure schedule is 10 minutes at 375 F peak metal temperature. d. Salt spray resistance per ASTM B 177 must be greater than hours with less than 1/8 creepage and no blistering. 3. Black Product # PRPL98019 Polyester Thermosetting Powder Coating a. All oil, grease, scale, and rust must be removed prior to applying finish. b. Film thickness must be mils baked to a smooth finish. c. Cure schedule is 10 minutes at 340 F peak metal temperature. d. Salt spray resistance per ASTM B 177 must be greater than hours with less than 1/8 creepage and no blistering. e. 60% gloss. PART 3: EXECUTION 3.01 INSPECTION A. Job Conditions 1. Verify that openings are dimensionally within allowable tolerances, plumb, level and clean. Provide a solid anchoring surface in accordance with approved shop drawing INSTALLATION A. Use only skilled tradesmen with work done in accordance with approved shop drawing and specifications.
6 6 B. Plumb and align shutters in a single plane for each wall frame and erect barriers and material square and true, adequately anchored to maintain positions permanently when subjected to normal thermal and building movement and specified wind loads. END OF SECTION EXETER ARCHITECTURAL PRODUCTS, INC. 242 West Eighth Street 3251 S.W. Island Way Wyoming PA Palm City, FL (Fax) (Fax)
GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM
1 GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials and services to furnish and install SECURITY
More informationMPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More informationSILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
More informationSERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651
SERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows as
More informationMARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationSeries B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
More informationMPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More informationSECTION ORNAMENTAL ALUMINUM FENCING
SECTION 032300 ORNAMENTAL ALUMINUM FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationHORIZONTAL SLIDER SERIES 700. Main Frame Depth: 2 3/4 Glazing Thickness (Maximum): 5/8 Thermal Break:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 700 Main
More informationSECTION [ ] COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 [08 33 13] COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Metal Counter
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationSECTION OVERHEAD COILING SHUTTERS
SECTION 08336 OVERHEAD COILING SHUTTERS This guide specification has been prepared by C.H.I. Overhead Doors to assist design professionals in the preparation of a specification section covering steel,
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationHeavy Commercial / Architectural Projected Windows Series L900T AW150
Heavy Commercial / Architectural Projected Windows Series L900T AW150 Section 08520...Aluminum Windows PART 1: WORK INCLUDED GUIDE SPECIFICATION A. The conditions of the contract and applicable sections
More informationSECTION / / BULLET RESISTANT SOUND CONTROL WINDOWS
SECTION 08381 / 088856 / 085673 BULLET RESISTANT SOUND CONTROL WINDOWS 1.0 GENERAL 1.1 DESCRIPTION OF WORK A. Furnish and install FACTORY PREGLAZED Bullet Resistant Sound Control Windows specified herein
More informationA. Access doors and frames are part of an access door and frame allowance.
SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFL200 13/4 x41/2 GUIDE SPECIFICATION. Non-Thermal Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSECTION Coiling Counter Shutters
SECTION 08 3313 Coiling Counter Shutters PART 1 GENERAL 1.1 SECTION INCLUDES A. Rolling Steel Doors B. Guides and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening
More informationSECTION Coiling Counter Shutters
SECTION 083313 Coiling Counter Shutters PART 1 GENERAL 1.1 SECTION INCLUDES A. Rolling Steel Doors B. Guides and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationSECTION ORNAMENTAL WELDED STEEL FENCING
SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSeries 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationCTB Commercial Aluminum Window
Technical Information Description The is thermally-broken for use in commercial construction. Basic models include horizontal slider, single hung and fixed picture windows. Units are mulled together with
More informationCOVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec PART 1 - GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationTRUMAN STATE UNIVERSITY GREENWOOD SCHOOL WINDOW REPLACEMENT
SECTION 085200 - WOOD WINDOWS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationUnited Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
More informationSection A2 Table of Contents ALL GLASS ENTRANCES
Architectural Aluminum Entrances Storefronts Curtain Walls Impact-Resistant Systems Section A Table of Contents ALL GLASS ENTRANCES Specifications...S-S Swing Type A... - Swing Type F... - Swing Type P...
More informationSILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
More informationSECTION MISCELLANEOUS METALS THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION MISCELLANEOUS AND ORNAMENTAL IRON
SECTION 055000 THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION 050001 MISCELLANEOUS AND ORNAMENTAL IRON PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a
More informationSECTION EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSECTION ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS
PART 1 GENERAL SECTION 08 1116 ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS 1.01 SECTION INCLUDES A. Aluminum-framed storefront, with vision glass. B. Infill panels of glass. C. Aluminum doors
More informationSeries 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationFIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4. Glazing Thickness (Maximum): 1
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A440-08
More informationAluminum Flush Doors and Frames SPECIFICATIONS. Section [8120] PART 1 GENERAL
Aluminum Flush Doors and Frames SPECIFICATIONS Section 081116 [8120] Cline Aluminum Doors, Inc. 112 32nd Avenue West Bradenton, FL 34205-8907 Toll-Free (800) 648-6736 Office (941) 746-4104 Fax (941) 746-5153
More informationSECTION DETAILS (MECHANICALLY ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationPROJECT IN SERIES 1300 NARROW SIGHT LINE AAMA/WDMA/CSA 101/I.S.2/A Structural Performance:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT IN SERIES 1300 NARROW SIGHT
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationSERIES /8 HORIZONTAL SLIDING WINDOW (CW30)
SERIES 525 2-5/8 HORIZONTAL SLIDING WINDOW (CW30) I. GENERAL: SPECIFICATIONS Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this
More informationSECTION U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR
Page 1 of 6 SECTION 08 39 80 U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR U.S. Aluminum has designed one of the most demanding air and water protection products, the BAL- 350 Small
More informationSECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS [OR WOOD] PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationImpact-Resistant Entrances Series
ARCHITECTURAL PRODUCTS Impact-Resistant Entrances Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES
More informationSECTION STRUCTURE MOUNT RAILING SYSTEM
SECTION 05520 STRUCTURE MOUNT RAILING SYSTEM Peak Fall Protection specializes in the design, engineering, fabrication, installation, and certification of fall protection safety systems. Our team of safety
More informationSECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
More informationB. Polyethylene samples shall be submitted for Owner approval of color and quality.
Glass Rail ENGINEERED DASHERBOARD SPECIFICATIONS PART 1 - GENERAL 1.01 PROJECT SCOPE A. Contractor shall furnish and install one complete set of steel framed dasherboards as indicated on the drawings and
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel Windows
More informationModel 8000 Double Hung H-C x 2311 (56 x 91 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationAluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS
Aluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS This suggested guide specification has been developed using the current edition
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Horizontal Slider (900) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Horizontal Slider (900) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel
More informationSECTION SERIES ALL GLASS ENTRANCES
1 SECTION 08 4210 1200 SERIES ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1.
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationSERIES /8 SINGLE HUNG (CW50)
SERIES 515 2-5/8 SINGLE HUNG (CW50) SPECIFICATIONS I. GENERAL: Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this project as
More informationSpecifications for FL-100 Soffit Panel
Union Corrugating Company Specifications for FL-100 Soffit Panel SECTION 07410 METAL SOFFIT PANELS PART 1 GENERAL 1.1 DESCRIPTON A. Section Includes: 1. Preformed metal soffit panel system 2. Associated
More informationSECTION ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY
3-PART SPEC ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY SECTION 05720 A. Section Includes: a. Solutions aluminum extruded shape top rail, square or round balustrade & rectangular bottom
More informationSECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System
SECTION 13096 RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13096-1 RF MODULAR PAN SYSTEM PART 1 GENERAL 1.1
More informationModel 2000 Single Hung H-HC x 2515 (60 x 99 )
Architect to edit the items in red. PART 1 - GENERAL 1.01 GENERAL PROVISIONS: A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work
More informationSeries 8100 Horizontal Slider HS-C x 1524 ( 71 x 60 )
1.01 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract, and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
More informationC. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American Architectural Manufacturers
More informationSPECIFICATIONS: Architectural Aluminum Railings
PART ONE: GENERAL 1.1 SUMMARY SPECIFICATIONS: Architectural Aluminum Railings A. Work in this section includes custom and standard Interior and Exterior aluminum railings and guardrails. 1.2 PERFORMANCE
More informationSpecification Section Storefront Systems has been revised. Omit previously issued Storefront section.
December 28, 2018 ADDENDUM NO. 2 To: Re: Bidders Corey Pitts, NewQuest Properties This Addendum forms a part of the contract documents identified above. Acknowledge the receipt of this Addendum on the
More informationSECTION PASS WINDOWS. 1.1 SUMMARY A. Section Includes: 1. Factory finished sliding glass, counter mounted pass windows.
SECTION 08 56 19 PASS WINDOWS SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Factory finished
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationFL550 21/2 x5 GUIDE SPECIFICATION. Impact-Resistant Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More informationRAOUL WALLENBERG HIGH SCHOOL SECURITY COILING GRILLE SFUSD PROJECT NO SAN FRANCISCO UNIFIED SCHOOL DISTRICT SECTION 08330
SECTION 08330 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: Provide all labor, materials, necessary equipment, services and included but limited to all related work to complete security coiling grille
More informationSECTION EXTERIOR SUN SHADES
SECTION 10 71 13 EXTERIOR SUN SHADES USE THIS SECTION WHEN SPECIFYING C.R. LAURENCE 7700 SERIES ALUMINUM SUN SHADE SYSTEMS. THE CRL 7700 SERIES SUN SHADE SYSTEM IS A FIXED BAR GRILLE STYLE WITH A TAPERED
More informationHORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA
More informationHORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA
More informationSECTION Coiling Doors and Grilles Model 4320
SECTION Coiling Doors and Grilles Model 4320 PART 1 GENERAL 1.1 SECTION INCLUDES A. Rolling Steel Grilles B. Guides and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel Windows
More informationCASEMENT PROJECT OUT SERIES 2400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 2 3/8
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 2400
More informationCASEMENT PROJECT OUT SERIES 6400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 6400
More informationSECTION SECURITY GRILLES 670 SERIES UPCOILING SECURITY GRILLE
SECTION 08 33 00 SECURITY GRILLES 670 SERIES UPCOILING SECURITY GRILLE Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on round
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationSECTION METAL EQUIPMENT LOCKERS
SECTION 10 51 13 - METAL EQUIPMENT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationModel STORM GRILLE Brick or Straight Pattern High Stress Rolling Grilles
Model STORM GRILLE Brick or Straight Pattern High Stress Rolling Grilles NOTE: For specifications, architects must choose from a variety of options. The standard choice will be shown first in plain text
More informationHORIZONTAL SLIDER SERIES 600 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 600 AAMA/WDMA/CSA
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS. A. This Section includes fixed and operable aluminum-framed windows.
SECTION 085113 - ALUMINUM WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes fixed and operable aluminum-framed windows. 1.2 PERFORMANCE REQUIREMENTS A. General: Provide aluminum windows capable
More information2000/2100/2200 Series Heavy Commercial Sliding Patio Doors
2000/2100/2200 Series Heavy Commercial Sliding Patio Doors MANKO WINDOW SYSTEMS, INC. 800 HAYES DRIVE MANHATTAN, KANSAS 66502 PHONE: (800) 642-1488 (785) 776-9643 FAX: (800) 576-2656 (785) 776-9644 MANKO
More informationCOLLEGE OF STATEN ISLAND
SECTION 07415 ALUMINUM PLATE CEILING PANELS PART 1 GENERAL 1.01 SUMMARY A. Section Includes 1. The extent of panel system work is indicated on the drawings and in these specifications. The following specification
More informationSECTION ORNAMENTAL ALUMINUM RAILING
SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Decorative Wire Rope Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in
More informationPW251 21/2 x7 GUIDE SPECIFICATION. Curtain Wall
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08900 ALUMINUM CURTAIN WALL This suggested guide specification has
More informationDOUBLE HUNG SERIES 860 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F. 50. Thermal U Value:.61. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com DOUBLE HUNG SERIES 860 AAMA/WDMA/CSA
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
More informationSPECIFICATION SECTION PART 1 GENERAL
PART 1 GENERAL 1.01 Summary A. Furnish and install louvers, bird screens, blank-off panels, structural supports and attachment brackets as shown on the drawings, as specified, and as needed for a complete
More informationSECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM
Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING
More informationSECTION OVERHEAD COILING FIRE DOORS MODEL 662 OVERHEAD COILING COUNTER FIRE DOORS WITH INTEGRAL FRAME
SECTION 08331 OVERHEAD COILING FIRE DOORS MODEL 662 OVERHEAD COILING COUNTER FIRE DOORS WITH INTEGRAL FRAME Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES
More informationCASEMENT PROJECT OUT SERIES 4400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 4400
More information