D Side lap. Side lap screw spacing < 500mm factory-installed seals on side lap. Decoupling tape > 60mm

Transcription

1 25 Side lap screw spacing < 500mm Decoupling tape > 60mm 3 factory-installed seals on side lap Side lap D 201.1

2 SECTION VIEWS Type L Ridge profile Type R Ridge flashing FLOOR PLAN > 200 overlap > 200 overlap L R Laid from left to right Laying direction Laying direction Laid from right to left Prevailing weather Side and end lap D 202.1

3 Construction connection in upper edge possible Minimum overlap depending on roof slope 200mm ~50 PU foam or mineral wool, compressed 3mm spacer strip b 40mm, e.g. type 7 a, 2 x Type 2 (at least 15mm wide) 100mm minimum support width Apply sealing compound to sandwich panel side joint under sealing tape Decoupling tape 60mm End lap D 203.1

4 End overlap Glue to edge a) flexible PE foam strip b) PU foam c) mineral wool, compressed Apply sealing compound to sandwich panel side joint under sealing tape Apply sealing compound to sandwich panel side joint under sealing tape Eaves D 204.1

5 20 / 3-9 Apply sealing compound to sandwich panel side joint under sealing tape 2x type 1A, 20 / 5-9 PU foam or mineral wool, compressed Apply sealing compound to sandwich panel side joint under sealing tape, Eaves D 205.1

6 End overlap Glue to edge max Type 2 30 / 2 PU foam or mineral wool, compressed Roof overhang 100mm Verge D 206.1

7 End overlap Glue to edge Type 2 30 / 2 PU foam or mineral wool, compressed Apply sealing compound to sandwich panel side joint under sealing tape Verge D 207.1

8 Lap formation lower ridge flashing Apply - adhesive to the lap edge 50mm 2x profile filler PU foam or mineral wool, compressed Upper ridge flashing with overlapping 5cm Sealing tape type 1 /1-4 Execute joint on upper edge Turn lower edge up 80mm 80mm Apply sealing compound or sealing tape to side joint Ridge D 208.1

9 Lap formation lower ridge flashing Apply type 1 - adhesive to the lap edge 50mm Profile filler Type 2 15 / 4 Upper ridge flashing with overlapping lap 5cm Sealing tape type 1 /1-4 Execute joint on upper edge PU foam Sprocket profile Turn lower edge up Apply sealing compound or sealing tape to side joint Ridge D 209.1

10 End overlap Glue to edge Turn lower edge up 2x profile filler 80mm a) soft PE foam strip b) PU foam c) mineral wool, compressed 2x Apply sealing compound to sandwich panel side joint under sealing tape Mono ridge D 210.1

11 Apply sealing compound to pitched roof overlap with lap plate Turn lower edge up Profile filler Type 2 15 / 4 Sprocket profile a) soft PE foam strip b) PU foam c) mineral wool, compressed 2x Apply sealing compound to sandwich panel side joint under sealing tape Mono ridge D 211.1

12 Overlapping lap molded part Sealing compound type 4 PU foam or mineral wool, compressed 150mm Turn lower edge up 300mm 80mm Decoupling tape 60mm Vertical wall connection D 212.1

13 PU foam or mineral wool, compressed 150mm Type 2 30 / 2 Horizontal wall connection D 213.1

14 Properties DIN A Type 2 Type 3 Type 4 Type 5 Type 6 Material PUR foam PUR foam Open-cell PUR foam Butyl tape Elasto-plastic bitumen/natural rubber PUR Soft foam, open-cell with polypropylene film Closed-cell PE foam (profile filler) Stress group (SG) SG 1 SG 1 Acrylic polymer impregnation Features Yes Yes Yes No requirement No requirement Yes No requirement Self-adhesive on one side Self-adhesive on one side, delayed decompression Self-adhesive on one side Self-adhesive on both sides, aluminumlaminated as required Self-adhesive Self-adhesive on one side Follows molded part shape Building material class 4102 B1 B1 B2 B2 B2 B2 B2 Vapor diffusion resistance value Thermal conductivity max. W/(m*K) Temperature resistance min. requirement Joint permeability m 3 /[h*m*(dapa) n ] < 100 < 100 < 100 Vapor retarder Vapor retarder - 30 C to + 80 C a < 0.1 a < 0.1 a < 0.1 a = 0 a = 0 a < Driving rain resistance Pa 600Pa 300Pa Weather resistance Compatibility with materials Dimensions in mm Min. tape width / max. joint width Must be fulfilled Must be fulfilled Must be fulfilled Must be fullfilled UV-resistant and aluminum-laminated as required Must be compatible 14/1-3, 10/2-6 14/2-6, 14/3-9 14/5-12, 18/ /3-5 20/5-9 30/2 15/4 Must be fulfilled Must be fulfilled Must be fullfilled UV-resistant and aluminum-laminated as required Profile shape modified min. 30mm Sealing tape types Type 7 Closed-cell PP or PE foam (decoupling tape) and others No requirement Self-adhesive on one side acc. to DIN EN ISO Compression force deflection 10% > 250 kpa, at 25% > 300 kpa B C to + 80 C Must be fulfilled Must be compatible 80/3 60/3 40/3 As of: 09/15