SECTION CERAMIC TILE. B. Ceramic tile wall finishes including standard and custom designs.
|
|
- Sybil Walsh
- 6 years ago
- Views:
Transcription
1 SECTION CERAMIC TILE PART 1 GENERAL 1.1 SECTION INCLUDES A. Ceramic tile floor and base finishes. B. Ceramic tile wall finishes including standard and custom designs. 1.2 REFERENCES A. ANSI/TCNA A108 - Ceramic Tile Installation. B. ANSI/TCNA A Installation of Grout in Tilework. C. ANSI/TCNA A Latex-Portland Cement Mortar. D. ANSI/TCNA A Ceramic Tile Grouts. E. ANSI/TCNA A Specifications for Ceramic Tile. F. TCNA (Tile Council of North America) - Handbook for Ceramic Tile Installation. G. ASTM C144 - Aggregate for Masonry Mortar. H. ASTM C150 - Portland Cement. I. ASTM C206 - Lime. 1.3 SUBMITTALS A. Shop Drawings: Indicate color arrangement, perimeter conditions, junctions with dissimilar materials, thresholds, and setting details. Provide layout drawings for signage type tile and custom mural pattern indicating patterns and colors provided. B. Product Data: Indicate material specifications, characteristics, and instructions for using mortars and grouts. C. Samples: Mount tile and apply grout on one plywood panel, to indicate pattern, color variations, and grout joint size variations of each tile type. D. Submit manufacturer's installation instructions. 1.4 QUALITY ASSURANCE A. Conform to ANSI/TCNA A137.1 B. Conform to TCNA Handbook for Ceramic Tile Installation and ANSI/TCNA A QUALIFICATIONS Standard Specifications Page 1 of 6
2 A. Manufacturer: Company specializing in the manufacture of products specified in this Section with minimum five (5) years experience. B. Installer: Company specializing in applying the work of this Section with minimum five (5) years experience. 1.6 ENVIRONMENTAL REQUIREMENTS A. Do not install adhesives in a closed, unventilated environment. B. Maintain 50 degrees F during installation of mortar materials. 1.7 EXTRA MATERIALS A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents. Provide 10% attic stock of field color and 5% accent color. (Review with Owner to verify quantity.) B. Furnish all remaining materials of each type, color, pattern, and size of ceramic tile and grout installed to owner s carpet/tile shop supervisor. 1.8 WARRANTY A. Provide comprehensive (5) year warranty on defects and installation. PART 2 PRODUCTS 2.1 MANUFACTURERS TILE A. Dal Tile Co. B. American Olean Tile Co. C. Summitville. D. Laticrete. E. Innovative Ceramic s Inc. (ICI). F. Approved Equal. 2.2 TILE MATERIAL A. Porcelain Ceramic Floor Tile: ANSI/TCNA A137.1, 8-inch and 12-inch square nominal. 1. Standard floor tile shall be unglazed, in patterns and colors as shown on drawings and schedules. B. Ceramic Wall Tile: ANSI/TCNA A137.1, 4-1/4 inch square nominal, glass with matching 1/4 radius edge trim pieces. 1. Standard wall tile shall be in patterns and colors as shown on drawings and schedules. 2. Custom wall tile shall be same tile type as specified for standard wall tile except design and colors shall conform to Men and Women restroom ID panels, illustrated on the Drawings. Font on restroom is Futura Regular. Tile shall be installed in sequence and pattern shown on Drawings. (See Exhibit A). Standard Specifications Page 2 of 6
3 C. Ceramic Wall Tile - Restroom Accent: ANSI/TCNA A137.1, 4-1/4 inch square nominal, ceramic mosaic, matt glazed, color and pattern as shown on drawings. D. Base: ANSI/TCNA A137.1, 6" x 8", flat top edge, coved internal corner; match floor tile color and finish. 2.3 MORTAR MATERIALS A. Dry-Set Mortar: ANSI A B. Latex-Portland Cement Mortar: ANSI A C. Portland Cement: ASTM C150 Type 1. D. Lime: ASTM C206 Type S. E. Sand: ASTM C144. F. Water: Potable. 2.4 GROUT MATERIALS A. ANSI A118.6, color as shown on drawings and schedules. Unsanded grout for wall ceramic tile. Sanded grout for porcelain floor tile. 2.5 ACCESSORIES A. Waterproofing Membrane: Cold-applied liquid similar to Laticrete No, 9235 waterproofing membrane, SGM Deck Seal 1000 or Hydroment Ultra-Set. Anticrack membrane similar to Laticrete-Blue Anti-Fracture membrane. B. Backing Board: ANSI/TCNA A118.9, high density, cementitious, glass fiber reinforced, ½ inch thick; 2 inch wide coated glass fiber tape for joints and corners. C. Reinforcing mesh: 2 x 2 inch size weave of 16/16 wire size, welded fabric, galvanized. D. Sealer: Approved by tile manufacturer, equal to Summitville SL-15 Seal Penetrating Grout and Tile Sealer. PART 3 EXECUTION 3.1 EXAMINATION A. Verify that surfaces are ready to receive work. Coordinate with work of Section Demolition. B. Beginning of installation means installer accepts condition of existing substrate. 3.2 PREPARATION A. Protect surrounding work from damage or disfiguration. B. Vacuum clean existing substrate and damp clean. Standard Specifications Page 3 of 6
4 C. Seal substrate surface cracks with filler. Level existing substrate surfaces to acceptable flatness tolerances. D. Accurately lay out tile designated for signage type in accordance with drawings. 3.3 CERAMIC FLOOR TILE INSTALLATION - FULL MORTAR BED METHOD A. Provide full mortar bed installation. B. Installation shall be in accordance with TCNA Handbook for Ceramic Tile Installation, Handbook Method Number F with waterproof membrane and reinforcing at mortar bed conditions and Method Number F with waterproof membrane at thin-set conditions. C. Apply mortar bed over surfaces in thickness to allow top of ceramic tile finish to match adjacent floor levels. D. Cut and fit tile tight to penetrations through tile. Form corners and bases neatly. Align floor, base and wall joints. Center in area. E. Place tile joints uniform in width, subject to variance in tolerance allowed in tile size. Make joints watertight without voids, cracks, excess mortar, or excess grout. F. Sound tile after setting. Replace hollow sounding units. G. Keep expansion joints free of mortar or grout. Apply sealant to joints. H. Allow tile to set for a minimum of forty-eight (48) hours prior to grouting. I. Grout tile joints. J. Apply sealant to junction of tile and dissimilar materials and junction of dissimilar lanes. K. Seal grout joints and unglazed tile. Sealer to be applied immediately after tile installation for protection of grout during remainder of construction. L. Where applicable slope tiles to floor drains to provide proper drainage. 3.4 CERAMIC WALL TILE INSTALLATION A. Where installed on masonry construction, installation shall be in accordance with TCA Handbook for Ceramic Tile Installation, Handbook method Number W202, Thin-Set installation with Latex-Portland Cement mortar and Grout. B. Where installed on metal stud and gypsum board construction, installation shall be in accordance with TCNA Handbook for Ceramic Tile Installation, Handbook method Number W244, Thin-Set installation over Backing Board with Latex-Portland Cement mortar and Grout. C. Install backing board in accordance with manufacturer s instructions and TCNA requirements for specified installation. Include 15 lb. felt membrane between studs and backer board. Tape joints and corners with 2" glass fiber mesh tape embedded in skim coat of mortar. Standard Specifications Page 4 of 6
5 D. Lay tile to pattern indicated on drawings. Do not interrupt tile pattern around openings. Align wall, base and floor joints. E. Align wall, base, and floor joints. F. Form internal angles coved and external angles bullnosed. G. Cut and fit tile tight to penetrations through tile. Form corners and bases neatly. H. Place tile joints uniform in width, subject to variance within tolerance allowed in tile size. Make joints watertight, without voids, cracks, excess mortar or excess grout. I. Sound tile after setting. Replace hollow sounding units. J. Keep expansion joints free of mortar or grout. Apply sealant to joints. K. Allow tile to set for a minimum of forty-eight (48) hours prior to grouting. L. Grout tile joints. M. Apply sealant to junction of tile and dissimilar materials and at junction of dissimilar planes. N. Seal grout joints and all unglazed tile. Sealer to be applied immediately after tile installation for protection of grout during remainder of construction. 3.5 PROTECTION A. Do not permit traffic over finished floor surface for seven (7) calendar days. B. Sealer shall be applied to all grout joints and unglazed tile before traffic is allowed over area. END OF SECTION Standard Specifications Page 5 of 6
6 EXHIBIT A Standard Specifications Page 6 of 6
SECTION TILING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS
More informationSECTION CERAMIC and QUARRY TILE
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 30 13 CERAMIC and QUARRY TILE A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 specification
More information1.3 Work shall include all reinforcement and accessories necessary to complete installation.
CERAMIC TILING GENERAL INFORMATION 1.1 Ceramic mosaic tile floors and bases, glazed wall tile wainscots and walls, and marble thresholds. 1.2 Installation will typically be with latex-portland cement mortar
More informationBuildingName The Description of the Project P DOCUMENTS
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
More informationStudent Services & Classroom Addition
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION TILING
SECTION 09 30 00 TILING PART 1 - GENERAL 1.1 SUMMARY A. Section includes tile as indicated on new surfaces and as specified. 1.2 SUBMITTALS A. Samples: 1. Submit samples of colors and sizes of tile. B.
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information***************************************************************************************************************
09330 QUARRY TILE *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number 09 30 16 ***************************************************************************************************************
More informationSECTION CERAMIC TILE
SECTION 09300 CERAMIC TILE PART 1 GENERAL 1.1 SCOPE A. Drawings and general provisions of the Contract, including General and Supplementary General Conditions, Division 00 & 01 Specification Sections,
More informationEditing notes to assist users are separated from specification text by rows of asterisks. Delete these notes prior to final printing.
SECTION 09635 LIMESTONE FLOORING This guide specification has been prepared by TexaStone Quarries LLC to assist design professionals in the preparation of a specification section covering cut limestone
More informationB. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.
SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationDivision 09 Finishes Section Ohio Utilities Protection Service New Office Building Bid Package B TILING
SECTION 09 30 00 TILING PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Porcelain Paver Tile. 2. Mortars and Grouts. 3. Floor Preparation Materials. B. Related Sections: Documents relating to the work
More informationSECTION TILING PART 1 - GENERAL 1.1 SUMMARY. A. Section Includes: 1. Ceramic tile. 2. Waterproof membrane. 3. Metal edge strips.
SECTION 093000 - TILING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ceramic tile. 2. Waterproof membrane. 3. Metal edge strips. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSECTION TILING
SECTION 093000 TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationTILING Lutheran Church of the Holy Spirit
SECTION 093000 - TILING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Porcelain tile. 2. Tile backing panels. 3. Metal edge strips. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSECTION CERAMIC TILING
SECTION 09 3013 CERAMIC TILING PART 1 - GENERAL 1.1 SUMMARY A. Includes But Not Limited To: 1. Furnish and install ceramic tile and tile setting materials and accessories as described in Contract Documents.
More informationDIVISION 9 - FINISHES
Part 1 - General 1.01 Work Included: A. All materials, labor services and incidentals necessary for the completion of this section of the work. 1.02 Quality Assurance: A. Standards: 1. Tile Council of
More information1.6 QUALITY ASSURANCE A. Source Limitations for Tile: Obtain tile of each type and color or finish from one source or producer.
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationA. Product Data: For each type of tile, mortar, grout, and other products specified.
SECTION 09310 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationA. Module Size: Actual tile size (minor facial dimension as measured per ASTM C 499) plus joint width indicated.
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Special Conditions and Division 01 Specification Sections, apply
More informationSECTION QUARRY TILE. A. American National Standards Institute ANSI A108.3.
SECTION 09330 QUARRY TILE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 07900 - Joint Sealers. 3. 09310 - Ceramic Tile. 4. 15421 - Drains and Cleanouts. 1.02 REFERENCES
More informationTILE TILE
09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements
More informationSECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION
SECTION 093000 - SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing, vapor retarder, and crack isolation in conjunction
More informationSECTION PAVER TILE
SECTION 09340 PAVER TILE PART 1 - GENERAL 1.01 DESCRIPTION: A. This section specifies providing paver tiles, typically in patron areas as shown. These tiles are noted on Drawings as: 1. Paver tile. 2.
More informationSECTION BRICK FLOORING
SECTION 09 63 13 BRICK FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brick flooring
More informationBush Elem. Addition & Alterations QUARRY TILE SECTION QUARRY TILE PART 1 - GENERAL
73651.01 QUARRY TILE 093016-1 1.1 RELATED DOCUMENTS: SECTION 093016 - QUARRY TILE PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationConstruction Specification
PART 1 - GENERAL 1.01 SUMMARY A. Furnish all labor, materials, tools and equipment required for completing tile work and related items indicated on the drawings and herein specified. B. Related work specified
More informationSECTION STONE FLOORING
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 63 40 STONE FLOORING SPEC WRITER NOTE: Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and
More informationSECTION ULTRACOMPACT WALL FINISHES - THIN SET
PART 1. GENERAL 1.1 SUMMARY A. Section Includes: 1. Quartz interior wall finishes. 2. Setting materials and accessories. B. Related Sections: 1. Division 01: Administrative, procedural, and temporary work
More informationCSI GUIDE Countertops
CSI GUIDE Countertops Part 1 General 1.0 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply
More informationADDENDUM NO. 6. Acknowledge receipt of this Addendum in the space provided in the Proposal Form. Failure to do so may disqualify the Bidder.
PROJECT: Lovington Fire Station # 2 WDG PROJECT NO: 445-01 DATE: July 120, 2018 ADDENDUM NO. 6 NOTICE TO PROPOSERS: This Addendum forms a part of the Contract Documents and modifies the original Specifications
More informationInstallation of Large Format Tile & Stone
Installation of Large Format Tile & Stone TDS 193 Use of Large Format Tile and Stone Twenty to twenty five years ago choosing tile was simple. Floor tile was typically 8 x 8 (200mm x 200mm) and wall tile
More informationSECTION SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING
SECTION 093000 - SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used for sound reduction, crack isolation
More informationSub-Section Paver Tiling
Section 093019 StonePeak Ceramic Guide Specification 093019-- 1 Division 09 Finishes Section 093000 Tiling Sub-Section 093019 Paver Tiling NOTE TO SPECIFIER: Please review the entire specification before
More informationC. Module Size: Actual tile size plus joint width indicated.
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationRENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11
SECTION 09 29 00 GYPSUM BOARD 05/11 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK ND AND 3 RD FIX FINISHES
CONTENTS 10.1 PLASTERWORK 10.2 2 ND AND 3 RD FIX FINISHES FUNCTIONAL REQUIREMENT 10.1 Plasterwork Workmanship Design Technical Manual TS-011-09-010412 i. All workmanship must be within defined tolerances
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationAcceptable Floor Substrates: Concrete, cured mortar bed, plywood, and backer board.
SECTION 093000 - SHEET MEMBRANE WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing and vapor retarder, in conjunction with tile and dimension stone installations.
More informationfor Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationSECTION SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING
SECTION 093000 - SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used for sound reduction, crack isolation
More informationHAWORTH PORCELAIN FLOORING SYSTEM CSI Specifications 03/29/2017. A. Concrete work and concrete floor sealer is specified in Section
SECTION 09 36 00 Dry-Lay Tile PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Concrete work and concrete floor sealer is specified in Section 03 30 00. B. Tiling as specified in Section 09 30 00. 1.2 SUMMARY
More informationSECTION CERAMIC TILING
SECTION 093013 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
More informationWALL TILE CHARACTERISTICS
DOCKSIDE Glazed porcelain tile is suitable for all interior floor, wall or ceiling ap-plications including wet areas. Exterior flooring application suitability is subject to slip & abrasion resistance
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES. Chapter 10
CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES 283 Chapter 10 FUNCTIONAL REQUIREMENTS FUNCTIONAL REQUIREMENTS 10.1 PLASTERWORK Workmanship i. All workmanship must be within the tolerances
More informationARDEX STONE VENEER INSTALLATION MATERIALS AND SYSTEMS
ARDEX GUIDE SPECIFICATION ARDEX AM 100 TM, ARDEX 8+9, ARDEX X77 TM, ARDEX X5 TM, and ARDEX FH TM Substrate Preparation Materials for Interior Applications to Receive the Installation of Tile and Stone
More informationSECTION UNIT PAVERS
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.
More informationSECTION MORTAR-BED STONE TILING [Interior Applications] [SECTION ]
(Specifier Note: The purpose of this guide specification is to assist the specifier in correctly specifying Porphyry Stone Pavers. The specifier needs to edit these guide specifications to fit the needs
More informationSECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications
More informationCONSOLIDATED EDISON COMPANY OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY DISTRIBUTION ENGINEERING DISTRIBUTION EQUIPMENT
CONSOLIDATED EDISON COMPANY OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY 10003 DISTRIBUTION ENGINEERING DISTRIBUTION EQUIPMENT SPECIFICATION EO-1007 REVISION 13 DECEMBER 2013 EFFECTIVE DATE DECEMBER 16,
More informationNarrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations Narrow Modular Pavers are part of the California Architectural
More informationSECTION LATEX-MODIFIED MEDIUM BED MORTAR
SECTION 09305.24 LATEX-MODIFIED MEDIUM BED MORTAR This product guide specification can be used to specify Hydroment Big Tile & Stone Mortar, a latex-modified, medium bed mortar designed for setting large
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Cast
More informationSECTION GRANITE TILING
SECTION 09 30 33.13 GRANITE TILING This guide specification utilizes recommendations and formats contained in references of the Construction Specifications Institute (CSI), including the CSI Practice Guides
More informationMANUFACTURER S SPECIFICATIONS Section LIMESTONE PLASTER
MANUFACTURER S SPECIFICATIONS Section 09220 LIMESTONE PLASTER LE DÉCOR LIMESTONE PART 1 GENERAL 1.1 General A. This section describes the requirements for furnishing and installing Limestone Plaster. 1.2
More informationCONSTRUCTION STANDARDS PAGE
CONSTRUCTION STANDARDS PAGE 093400-1 SECTION 093400 PART 1 - GENERAL 1.1 M.S.U. ISSUES A. Typical locations for wet area ceramic tile installation include areas such as swimming pools, showers, toilets,
More informationSECTION TILE Rev
PART 1 GENERAL 1.01 SECTION INCLUDES A. Tile. 1. Porcelain ceramic tile. B. Mortar and setting materials. SECTION 09300 TILE Rev 2-12-6-11 C. Grout. D. Membranes, including but not limited to: 1. Waterproofing
More informationEXTERIOR ROOF / DECK FLOORS Roof Deck, Drainage Layer, Mortar Bed Stone Tile
EXTERIOR ROOF / DECK FLOORS Roof Deck, Drainage Layer, Mortar Bed Stone Tile MAPEI: MF103-Stone TCNA: F103-15-Stone TTMAC: 325ED-E Version: 2015 DEPRESS 1" (25 mm)min,. 2" ( 50 mm) RADIUS 1) GROUT STONE
More informationSECTION RESILIENT FLOORING
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 65 00 RESILIENT FLOORING A. Resilient sheet and tile flooring B. Resilient base C. Resilient stair nosing, treads, risers and skirting 1.2 REFERENCES A. ASTM
More informationINTERIOR WALLS OVER SOLID BACKING
INTERIOR WALLS OVER SOLID BACKING Mortar Bed (One-Coat Method) Stone Tile MAPEI: MW222-Stone TCNA: W222-15-Stone TTMAC: N/A Version: 2015 SOLID BACKING: WOOD, PLASTER, MASONRY, OR GYPSUM BOARD STONE TILE
More informationChevy Chase Club June 2, 2008 Bowie Gridley Architects
SECTION 093033 - STONE TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION GYPSUM BOARD & SHEATHING SYSTEMS
PART 1!GENERAL! 1.01! SECTION INCLUDES SECTION 09260 GYPSUM BOARD & SHEATHING SYSTEMS! Metal stud wall framing. Metal channel ceiling framing.! Gypsum board.! Sheathing.! Taped and sanded joint treatment.!
More information2018 Flooring Specification - Tile Set Method TECTURA DESIGNS CEMENT TERRAZZO TILES
2018 Flooring Specification - Tile Set Method 09300 TECTURA DESIGNS CEMENT TERRAZZO TILES PART 1 - GENERAL 1.1 INTRODUCTION A. Tectura Designs, Terrazzo Tiles are to be installed following the tile setting
More informationADDENDUM NO. 1. By: David J. Davenport, AIA Architect
ADDENDUM NO. 1 Date: January 14, 2010 Project No: Pettigrew State Park, SCO ID#: 07-07085-01A Project: New Maintenance Area, Office Improvements & Pocosin Natural Area Improvements The following Addenda
More informationSECTION MANUFACTURED ROOF EXPANSION JOINTS
SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. Section includes cast-in-place concrete, including reinforcement, concrete materials, mixture design, placement procedures, and finishes.
SECTION 033053 - CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX
GlassPLANK GUIDE SPECIFICATION Manufacturer: GLASS RECYCLED LLC 2939 Irving Blvd Suite 305 Dallas TX 75247 (888) 523-7894 toll free voice www.glassrecycled.com SECTION 09 66 18 EPOXY TERRAZZO TILE WITH
More informationSample Specification
Sample Specification Enclosed is a template for you to use in preparing a final, quarry tile specification incorporating products manufactured by Metropolitan Ceramics, by Ironrock Capital, Inc. Quarry
More informationSample Specifications
Sample Specifications Below is a template for you to use in preparing a final, quarry tile specification incorporating products manufactured by Metropolitan Ceramics, by Ironrock Capital, Inc. Quarry tile
More informationFloor Insulation Underlayment Section Sound Control Matting
Floor Insulation Underlayment Section 09618 Sound Control Matting Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in excess of 50 to meet building
More informationSECTION ARDEX TILE AND STONE INSTALLATION MATERIALS AND SYSTEMS
ARDEX GUIDE SPECIFICATION ARDEX DS70 TM Acoustic Mat and ARDEX 8+9 TM Rapid Waterproofing and Crack Isolation Compound Subfloor Preparation Materials for Sound Deadening Applications to Receive the Installation
More informationSECTION CEMENTITIOUS SHEATHING
SECTION 06 16 63 CEMENTITIOUS SHEATHING SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this Section for exterior sheathing as a backup
More informationProduct Guide Specification
Product Guide Specification SECTION 04850 (04 40 00) NATURAL THIN VENEER STONE PART 1 GENERAL 1.1 SECTION INCLUDES Specifier Notes: Edit the following as required. A. Natural thin veneer stone for [exterior]
More informationCOOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No.
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationCalifornia Architectural Pavers for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: California Architectural Pavers for Mortar-Set Concrete Tiling Installations Stepstone, Inc. also manufactures California Architectural
More informationSample Specifications
Sample Specifications Below is a template for you to use in preparing a final, quarry tile specification incorporating products manufactured by Metropolitan Ceramics, by Ironrock Capital, Inc. Quarry tile
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSpec Master 5/7/ For each product requiring color and texture selection, provide full size samples.
SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationENKASONIC FLOOR UNDERLAYMENT 9110
ENKASONIC FLOOR UNDERLAYMENT 9110 GS1197 Section 13080 SECTION 09618 SOUND CONTROL MATTING Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in
More informationSOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA SPECIFICATION FOR CERAMIC TILE FOR 15 th STREET STATION
SOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA 19107 SPECIFICATION FOR CERAMIC TILE FOR 15 th STREET STATION TABLE OF CONTENTS Specification Sections: Division
More informationA. Section includes fluid applied, vapor permeable membrane air barriers.
Master Construction Specifications Insert Project Name SECTION 072726 FLUID APPLIED MEMBRANE AIR BARRIERS PART 1 GENERAL 1.1 SUMMARY A. Section includes fluid applied, vapor permeable membrane air barriers.
More informationSECTION Fiber Reinforced Stucco 1
CSI SECTION 09200 FIBER REINFORCED STUCCO PART 1 GENERAL 1.01 SUMMARY A. Section Description: Provided lath and plaster where shown on the Drawings, as specified herein, and as needed for complete and
More informationSECTION QUARRY TILE
SECTION 09 30 16 QUARRY TILE PART 1 GENERAL 1.1 SECTION REQUIREMENTS A. Provide all labor, materials and equipment required for the installation of quarry tile flooring as shown on drawings and schedules
More informationCTIOA REPORT (Rev )
CERAMIC TILE INSTITUTE OF AMERICA, INC. 12061 Jefferson Blvd., Culver City, CA 90230-6219 Phone (310) 574-7800 * Fax: (310) 821-4655 * Email: ctioa@earthlink.net Fed. I.D. #95-4401962 www.ctioa.org www.thetiledoctor.com
More informationSTEAM SHOWER / ROOM; WOOD OR METAL STUDS Wood or Metal Studs Cement Backer Board Walls, Mortar Bed Floor Ceramic Tile
STEAM SHOWER / ROOM; WOOD OR METAL STUDS Wood or Metal Studs Cement Backer Board Walls, Mortar Bed Floor Ceramic Tile MAPEI: MSR614 TCNA: SR614-13 TTMAC: 321SR-B SLOPED CEILING 2" (50 mm) PER FOOT CEMENT
More informationInstallation Standard For TILE-LINED ROMAN BATH TUBS IAPMO IS (10) Wall Finish. (3) Test Required. (2) Waterproof. Tile. (8) Concrete Shell
Installation Standard For TILE-LINED ROMAN BATH TUBS IAPMO IS 2-2003 (9) Ceramic Tile Floor Set in Portland Cement Mortar Sub-Floor & Building Felt 2 x 6 Floor Furring Wood Floor Joists Deflection of floor
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 09 2116 GYPSUM BOARD ASSEMBLIES A. Performance criteria for gypsum board assemblies. B. Metal channel ceiling framing. C. Backing board. D. Gypsum wallboard.
More informationCertainTeed. GlasRoc. Tile Backer
CertainTeed GlasRoc TM Diamondback GlasRoc Product Overview is a superior tile substrate for walls, ceilings, and countertops, specially designed by CertainTeed to meet the demands of highmoisture areas.
More information327 King Street Exterior Repairs & Interior Renovations Project No. H15-N200-PG
StudioA Architecture ADDENDUM NO. 2 Date: 11 October 2013 Re: 327 King Street Exterior Repairs & Interior Renovations Project No. H15-N200-PG From: Whitney Powers To: Bidders/Planholders This Addendum
More information1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets
SECTION 09 29 00 - GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation
More informationSTANDARD INSTALLATION GUIDELINES
GUIDELINES TOOLS MATERIALS SUBSTRATES PROCESSES TOOLS & MATERIALS PRIMARY INSTALLATION TOOLS NOTCHED EDGE TROWEL Suggested: 1/16 V Notch RUBBER FLOAT SPONGES RAZOR BLADES WATER BUCKETS PAINT BRUSH OR ROLLER
More informationCONCRETE STAIRS Note:
With the increased use of concrete tile and stone over the past decade, there has been an increase in demand for installing concrete tile or stone on stairs. Historically, these types of installations
More informationExterior Walls Wood or Metal Studs Cement Backer Board Ceramic Tile
Exterior Walls Wood or Metal Studs Cement Backer Board Ceramic Tile MAPEI: MW244E TCNA: W244E-13 TTMAC: 305W-A CERAMIC TILE 1). GROUT 2). CEMENTITIOUS BOND COAT 3). BONDED WATERPROOF MEMBRANE CEMENT BACKER
More informationKolorines Glass Mosaic Tiles Project Specification
Kolorines Glass Mosaic Tiles Project Specification SUGGESTED SPECIFICATION Glass Mosaic Tile Installation for Swimming Pools NOTES TO SPECIFIER: 1. Specify PremiumPlus Thin-Set mixed with CustomFlex Additive
More informationSECTION UNIT MASONRY
SECTION 04200 UNIT MASONRY PART 1 GENERAL 1.01 SUMMARY A. Furnish labor, materials, and equipment and perform functions required in the installation and maintenance of the work covered by this Section.
More informationSECTION QUARTZ SURFACING COUNTERTOPS
SECTION 12 3661.19 QUARTZ SURFACING COUNTERTOPS This section includes editing notes to assist the user in editing the section to suit project requirements. These notes are included as hidden text, and
More informationReCote Finish System over Concrete
Part 1 General 1.01 GENERAL A. The Master Wall ReCote Finish System for smooth precast and cast in place concrete consists of an acrylic primer and ReCote acrylic finish. When needed an acrylic modified
More information