SECTION PREFABRICATED PIPE BRIDGE(s)

Size: px
Start display at page:

Download "SECTION PREFABRICATED PIPE BRIDGE(s)"

Transcription

1 SECTION PREFABRICATED PIPE BRIDGE(s) PART 1 - GENERAL 1.01 Scope A. The Contractor is responsible for all engineering design, detailing, fabricating, installation including foundations for the pipe bridge(s). All components and anchor bolts shall be provided by the fabricator/supplier. The design and detailing shall conform to the Applicable Codes and Standards listed in the section 2 of this document and shall comply with structural drawings/plans and this document. B. Pipe bridge(s) and its attachments shall be fully fabricated by a qualified supplier as outlined in this document. C. Pipe bridge supplier/fabricator shall be responsible for the delivery of all bridge materials including anchor bolts and foundation requirements. Contractor shall construct foundations using the supplier s requirements. D. These specifications are for fully engineered, pre-fabricated pipe bridges(s) of steel construction and shall be regarded as minimum standards for design and construction. E. Fabricator/supplier must meet or exceed all the following specifications. F. The pipe bridge manufacturer shall have been in the design and fabrication of steel bridge or support structures for a minimum of five (5) years Suppliers Documentation to ensure supplier/fabricator shall be in compliance with these specifications must be provided and shall include the following minimum criteria to be considered: Representative Design Calculations Representative Drawings Splicing and Erection Procedures Warranty Information Inspection and Maintenance Procedures Welder Qualifications PART 2 - APPLICABLE CODES AND STANDARDS A. Governing Codes and Standards 1. Bridge(s) shall be designed in accordance with the American Institute of Steel Construction, latest edition 2. Kentucky Building Code, latest edition B. Reference Codes and Standards 1. AASHTO Guide Specifications for the Design of Pedestrian Bridges 2. American Welding Society, Structural Welding Code, D1.1, latest edition C. Truss Design Option Truss design shall maintain the overall dimensions and clearances shown on the plans. Design shall accommodate the proposed utility lines to be attached including weight of contents. PART 3 - GENERAL FEATURES OF DESIGN A. Span Bridge span(s) are variable and are as shown on the plans. A minimum clearance of 18'-0 shall be maintained over roadways or drives. Location of other overhead or adjacent power lines or structures shall be verified to maintain code mandated clearances and avoidance of conflicts

2 B. W idth Inside clear width of the bridge shall be as shown on the plans. C. Bridge Type 1. Bridge(s) shall be a simple supported, multiple span steel truss, as defined in the structural drawings and this specification, or similar in look and function. Style must be approved in accordance with section 1.1 of this specification. 2. Bridge(s) shall be fabricated and delivered as continuous and pre-assembled structures unless mid-span splices are required for shipping purposes. 3. Bridge(s) shall be designed utilizing lateral and transverse bracing to resist deflection and twisting and increase stability without impeding the ability to attach utility conduits. D. Slope Bridge(s) shall be designed for abutments and/or piers constructed at the same elevation as indicated in the structural drawings/plans. E. Bearing Pads Bridge shall include bearing pads, which shall allow the bridge to expand and contract as needed without binding, in accordance with section 5.3 of this document. F. Bolted Slices Bolted splice design shall be in accordance with Section J3 of the Manual of Steel Construction. Splices shall be designed for the actual load in the member. PART 4 - ENGINEERING 4.01 Design Loads A. Dead Load The bridge shall be designed considering its own dead load including structure and fully loaded attached utility lines. In addition, ice loads shall be considered. B. Point Load The pipe bridge shall be designed for an occasional 1,000 lb point loading. C. Wind Loads 1. Horizontal Wind Load The bridge shall be designed for a horizontal wind load of 90 mph, applied to the full vertical projected area of the bridge as if enclosed, at right angles to the longitudinal axis of the structure. Wind loads shall be proportionally distributed across all exposed primary member surfaces including chords, vertical posts, and truss diagonals on the windward side. Fatigue effects shall be considered for all load combinations incorporating wind loads, where n=100,000 cycles. 2. Overturning Wind Load The effect of forces tending to overturn the structure shall be calculated assuming that the wind direction is at right angles to the longitudinal axis of the structure. In addition, an upward force shall be applied at the windward quarter point of the transverse superstructure width. This force shall be 20 pounds per square foot of projected surface area including pipes. D. Top Chord/Rail Load The top chord, top rail, and vertical posts shall be designed for a simultaneous vertical and horizontal load of 50 pounds per linear foot or a 200 pound point load, whichever is greater, positioned to produce the maximum load effect

3 4.02 Design Limitations A. Deflection The vertical deflection of the main truss due to any load combination shall not exceed L/500, where L is the length of the unsupported span. The horizontal deflection of the structure due to any load combination shall not exceed L/500, where L is the length of the unsupported span. B. Allowable Stresses All allowable stresses for steel shall be determined in accordance with the AISC Manual of Steel Construction related to design requirements and allowable stresses. C. Frame Stability The buckling load factor for the bridge structure shall be no less than 4 for any combination of applied loads, to ensure adequate overall stability and stiffness. D. Vibration The fundamental frequency of the unloaded bridge shall be no less than 3.0 Hz to avoid the first harmonic. E. Drain Holes W hen the collection of water inside a structural tube is a possibility, the tube shall be provided with a drain hole at its lowest point to let water out Analysis All analysis and results necessary to determine the structural adequacy of the catwalk shall be reported. The following analyses are required: A. Stress and Deflection Analysis shall be completed to determine that all bridge members, critical connections, and bridge configurations are sufficient to adequately resist the possible load combinations B. Frame Stability Buckling analysis shall be completed to determine that the bridge frame is adequately stable and sufficient to resist forces causing it to buckle. C. Frequency Frequency analysis shall be completed to determine that the catwalk frame is sufficient to avoid resonance due to frequencies likely encountered under normal use and when utility lines are empty. PART 5 - MATERIALS 5.01 Structural Members All primary structural members are to be ASTM A36 or A572. Tubular sections to be ASTM A500 Tube steel minimum thickness ¼ Steel shapes minimum thickness 5/16" Stainless Steel U-Bolts ASTM A 276 Chromium-Nickel Grade, min. yield 30,000 psi Steel Bolts, Nuts, Screws and Washers, High Strength ASTM A325 or A490 Structural Steel Welding Electrodes E70 or E80 Series 5.02 Bearing Pads All bearing pads shall be 1/8 thick UHMW adequately dimensioned to provide support to the structure over the full travel resulting from expansion and contraction

4 5.03 Anchor Bolts Anchor bolt assemblies shall be designed and supplied by the manufacturer in accordance with ASTM A 687. They shall be hot dip galvanized per ASTM A153. Washers shall conform to ASTM F436. PART 6 - FABRICATION & QUALITY ASSURANCE 6.01 Welding All members shall be welded using filler metal in accordance with AWS A5.28 for the GMAW process. W elding and weld procedure qualifications tests shall conform to AW S D Quality Requirements All welds shall be inspected by the fabricator to verify the reliability of production as follows: (a) Visual inspection of all welds, proof testing of welds, and sufficient destructive testing of weld samples fabricated during the production welding. (b) Poor welding workmanship noted by visual inspection will be sufficient cause for rejection CW I Welding Inspector Requirements Each bridge shall be inspected by a Certified Welding Inspector that is qualified under the AWS QC-1 program. This inspection shall include as a minimum requirement the following: review of shop drawings, weld procedures, welder qualifications, and weld testing reports, visual inspection of welds and verification of overall dimensions and geometry of the bridge. A report shall be produced indicating the above items were reviewed and shall be signed and sealed by the CW I signifying compliance with AW S D1.1 codes Welder Qualifications Before starting fabrication of structural steel, all welders shall be qualified in accordance with the latest edition of ANSI/AW S D1.1 Structural W elding Code. W elders shall have a minimum of 6 months experience in welding bridge structures. Requalification may be required any time there is specific reason to question the welder's ability Bridge shall be sandblasted in accordance with SSPC SPC-6 Commercial Blast Cleaning. The bridge will then be painted with an epoxy primer followed by an Aliphatic Urethane Gloss Enamel topcoat. Bridge shall be supplied paint for touch-up after field erection. Primer to be Devoe, Devguard 4160, multipurpose tank and structural primer and finish coat to be Devoe, DTM Urethane - Alkyd Gloss Enamel (3.0 mils dry) or approved equal. PART 7 - SUBMITTALS AND WARRANTY INFORMATION 7.01 Fabrication drawings Fabrication drawings and calculations shall be prepared and submitted for review after receipt of the order. Submittal drawings shall be unique drawings to this project, prepared to illustrate the specific portion of the bridge(s) being fabricated. All relative design information such as member size, material specification, dimensions, and required critical welds shall be clearly shown on the drawings. Drawings shall have cross referenced details and sheet numbers. All drawings shall be stamped, and signed by a Professional Engineer registered in the state of Kentucky. At minimum the following criteria must be included for approval: All Relevant bridge Dimensions Bridge Cross sections Sufficient Detailing Member Cross sections

5 General Notes indicating material specifications and design loads W eld Details Detail of Bolted Splices (if applicable) Foundation Design Signature and Seal of PE licensed in accordance with this specification 7.02 Calculations & Results Structural analysis results and calculations shall be prepared and submitted for review after receipt of the order. All analysis and results necessary to determine the structural adequacy of the bridge shall be shown W arranty The bridge supplier shall warrant the completed structure(s) to be free of design, material and workmanship defects for a period of 10 years from the date of delivery. PART 8 - DELIVERY AND ERECTION 8.01 Owner Information The owner will provide all necessary information about the site and soil conditions. Soil tests shall be procured by the owner. Foundations shall be designed for a soil bearing capacity of 3,500 psf. The engineering design and construction of the bridge abutments, piers and/or footing shall be by the bridge supplier. The Contractor shall install the anchor bolts in accordance with the supplier s anchor bolt spacing dimensions. All grounding and lightning protection shall be the responsibility of the Contractors and shall comply with 2008 National Electrical Code, Chapter Care A. Contractor shall take precautions to avoid scarring or marring steel surfaces. Any such damage causing objectionable appearance or contributing to weakness of the structure will be cause for rejection. B. Contractor to remove all milling irregularities. C. Tubing shall be seamless, clean, smooth and free from defects. D. Field check all dimensions before fabrication W eld Quality Regardless of the method of inspection, the acceptance or rejection of welds shall be determined by the following conditions: A. Cracks in welds or adjacent base metal are not acceptable. B. Excess porosity is not acceptable. C. Lack of fusion, incomplete penetration or oxide inclusions are acceptable only if small and well dispersed. End of Section

PREFABRICATED STEEL TRUSS SPECIFICATIONS

PREFABRICATED STEEL TRUSS SPECIFICATIONS PREFABRICATED STEEL TRUSS SPECIFICATIONS 1. GENERAL 1.1 Scope All engineering design and related detailing of the bridge(s) shall be provided by the supplier. The design and detailing shall conform to

More information

PEDESTRIAN BRIDGE 866/

PEDESTRIAN BRIDGE 866/ 866/258-3401 WWW.BRIDGEBROTHERSINC.COM 1 Purpose and Scope These specifications are for a fully engineered clear span bridge of welded steel construction and shall be regarded as minimum standards for

More information

STRUCTURAL STEEL FRAMING

STRUCTURAL STEEL FRAMING SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 SUMMARY A. Section includes 1. Structural steel framing 2. Structural steel framing required for support and framing of rooftop mechanical

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 1

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 1 MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 1 OFS:MJF 1 of 10 APPR:JAB:POJ:09-29-18 FHWA:APPR:10-01-18 a. Description. This work consists of

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2 MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2 OFS:MJF 1 of 10 APPR:JAB:POJ:09-29-18 FHWA:APPR:10-01-18 a. Description. This work consists of

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2 MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PREFABRICATED STEEL PEDESTRIAN BRIDGE, TYPE 2 OFS:MJF 1 of 10 APPR:JAB:POJ:07-07-17 FHWA:APPR:07-11-17 a. Description. This work consists of

More information

ADDENDUM NO. 3. A. Attached is the updated Revision of Section 509 Prefabricated Structural Steel Bridge.

ADDENDUM NO. 3. A. Attached is the updated Revision of Section 509 Prefabricated Structural Steel Bridge. Purchasing Division ADDENDUM NO. 3 DATE: March 26, 2019 FROM: City of Grand Junction Purchasing Division TO: All Offerors RE: 2019 Monument Road Bicycle Path Trail IFB-4618-19-DH Offerors responding to

More information

DIVISION 5 - STRUCTURAL STEEL AND IRON WORK

DIVISION 5 - STRUCTURAL STEEL AND IRON WORK DIVISION 5 - STRUCTURAL STEEL AND IRON WORK SECTION 05100 STRUCTURAL METAL FRAMING PART 1.00 GENERAL 1.01 SCOPE OF WORK A. Work Included: 1. 2. Structural steel complete in place. Steel joists complete

More information

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011. DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:

More information

SECTION COLD-FORMED METAL TRUSSES

SECTION COLD-FORMED METAL TRUSSES SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DIVISION 5 METALS SECTION STRUCTURAL STEEL

DIVISION 5 METALS SECTION STRUCTURAL STEEL DIVISION 5 METALS SECTION 05 12 00 PART 1 GENERAL 1.01 SUMMARY A. Section Includes: All labor and materials required to furnish and install the structural steel shown on the Drawings and required by these

More information

1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.

1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns. PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,

More information

STRUCTURAL STEEL FRAMING Section

STRUCTURAL STEEL FRAMING Section PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Structural steel. 2. Grout. 1.2 DEFINITIONS A. Structural Steel: Elements of the structural frame indicated on Drawings and as described in AISC 303,

More information

SECTION STRUCTURAL METAL FRAMING

SECTION STRUCTURAL METAL FRAMING SECTION 05100 STRUCTURAL METAL FRAMING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Structural steel framing including lintels, shelf angles, bearing plates, anchor bolts and other items as shown on

More information

STANDARD SPECIFICATION FOR ALUMINUM FRAMING FOR RAILROAD PASSENGER SHELTERS

STANDARD SPECIFICATION FOR ALUMINUM FRAMING FOR RAILROAD PASSENGER SHELTERS SOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA 19107 STANDARD SPECIFICATION FOR ALUMINUM FRAMING FOR RAILROAD PASSENGER SHELTERS REVISION DATE SPECIFICATION # F-S-304_

More information

Insulating Cellular Concrete Steel Joists Painting. A. America Society for Testing and Materials (ASTM):

Insulating Cellular Concrete Steel Joists Painting. A. America Society for Testing and Materials (ASTM): SECTION 05120 STRUCTURAL STEEL PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03342 - Insulating Cellular Concrete. 2. 05210 - Steel Joists. 3. 09900 - Painting. 1.02 REFERENCES A. America Society

More information

SECTION STEEL JOIST FRAMING

SECTION STEEL JOIST FRAMING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 05 21 00 1. Use this section only for NCA projects. 2. Delete between //---// if not applicable to project. Also delete any other item or paragraph not applicable

More information

SECTION STRUCTURAL STEEL

SECTION STRUCTURAL STEEL SECTION 051200 STRUCTURAL STEEL PART 1 GENERAL 1.01 SECTION INCLUDES A. Structural steel framing members and support members. B. Base plates, shear stud connectors. C. Grouting under base plates. 1.02

More information

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II SECTION 052100 - STEEL JOISTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections

More information

PLUMAS COUNTY DEPARTMENT OF PUBLIC WORKS

PLUMAS COUNTY DEPARTMENT OF PUBLIC WORKS PLUMAS COUNTY DEPARTMENT OF PUBLIC WORKS 1834 East Main Street, Quincy, CA 95971 Telephone (530) 283-6268 Facsimile (530) 283-6323 Robert A. Perreault Jr., P.E., Director John Mannle, P.E., Asst. Director

More information

C. Miscellaneous Metal Fabricators are specified elsewhere in Division 5.

C. Miscellaneous Metal Fabricators are specified elsewhere in Division 5. SECTION 05 1200 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.01 SUMMARY A. Extent of structural steel work is shown on drawings, including schedules, notes and details to show size and location of members,

More information

SECTION PLATE CONNECTED WOOD TRUSSES

SECTION PLATE CONNECTED WOOD TRUSSES SECTION 06173 PLATE CONNECTED WOOD TRUSSES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Shop fabricated wood trusses for roof and floor framing. 2. Bridging, bracing, and anchorage. B. Related Sections:

More information

SECTION MISCELLANEOUS METALS

SECTION MISCELLANEOUS METALS PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications

More information

DIVISION XIII - SPECIAL CONSTRUCTION

DIVISION XIII - SPECIAL CONSTRUCTION DIVISION XIII - SPECIAL CONSTRUCTION SECTION 13120 - PRE-ENGINEERED METAL BUILDING SYSTEM (RAILROAD EQUIPMENT ENCLOSURE BUILDING) PART 1 - GENERAL 1.01 WORK INCLUDED A. Work of this section covers the

More information

SECTION ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck)

SECTION ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck) SECTION 13125 ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck) PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

Special Provision No. 915S03 December References, Materials, Construction, and Quality Assurance for Sign Support Structures

Special Provision No. 915S03 December References, Materials, Construction, and Quality Assurance for Sign Support Structures STEEL MONOTUBE OVERHEAD SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN NON-BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. CANTILEVER STATIC SIGN

More information

.2 Section Waste Management and Disposal.

.2 Section Waste Management and Disposal. Issued 2006/08/01 Section 05121 Structural Steel for Buildings Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal..3 Section

More information

METAL FABRICATION..1 General Conditions and Division 1 shall govern Work of this section.

METAL FABRICATION..1 General Conditions and Division 1 shall govern Work of this section. CITY OF BRAMPTON LANDSCAPE SPECIFICATIONS SECTION 05500-1 PART 1 GENERAL 1.1 Description of Work.1 General Conditions and Division 1 shall govern Work of this section. 1.2 Quality Assurance.1 Personnel:.1

More information

A. The work under this section consists of furnishing and installing gauge steel framing and bracing as indicated on the drawings and as specified.

A. The work under this section consists of furnishing and installing gauge steel framing and bracing as indicated on the drawings and as specified. SECTION 05450 LIGHT GAUGE STEEL FRAMING SYSTEM PART 1 GENERAL 1.1 SUMMARY A. The work under this section consists of furnishing and installing gauge steel framing and bracing as indicated on the drawings

More information

SO-DEEP, 9/2015 (703) VA. Group I-DL. Group I-DL

SO-DEEP, 9/2015 (703) VA. Group I-DL. Group I-DL LIMITED ACCESS HIGHWAY By Resolution of Commonwealth Transportation Board dated January 18, 2001 PROJECT MANAGER: SURVEYED BY, DATE: TIMOTHY HARTZELL, P.E. (703) 259-2749 (NOVA District) PRECISION MEASUREMENTS,

More information

SECTION PRE-ENGINEERED COLD-FORMED METAL ROOF AND FLOOR TRUSSES

SECTION PRE-ENGINEERED COLD-FORMED METAL ROOF AND FLOOR TRUSSES SECTION 05440- PRE-ENGINEERED COLD-FORMED METAL ROOF AND FLOOR TRUSSES PART 1 GENERAL 1.01 SUMMARY A. Section includes pre-engineered, pre-fabricated cold formed steel framing elements. Work includes:

More information

SECTION METAL FABRICATIONS FOR STEAM UTILITY DISTRIBUTION

SECTION METAL FABRICATIONS FOR STEAM UTILITY DISTRIBUTION PAGE 055015-1 SECTION 055015 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,

More information

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces. SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DUGOUT MODEL (4 POST) 10 x 24 SPECIFICATIONS

DUGOUT MODEL (4 POST) 10 x 24 SPECIFICATIONS DUGOUT MODEL (4 POST) 10 x 24 SPECIFICATIONS Dimensions: Roof Dimensions 10-0 x 24 Column Dimensions (center to center) 6-7 x 22-9 Minimum Clearance 7-6 Minimum Clearance @ Front ±9-2 Roof Pitch 2:12 pitch

More information

SECTION METAL PLATE CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.01 RELATED DOCUMENTS

SECTION METAL PLATE CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.01 RELATED DOCUMENTS SECTION 06192 - PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

SECTION METAL WELDING

SECTION METAL WELDING SECTION 05222 - METAL WELDING PART 1 - GENERAL 1.01 SECTION INCLUDES A. Welding Rod/Electrodes B. Stud Shear Connectors C. Shop Welding D. Inspections and Tests by the Contractor E. Inspections and Test

More information

05510: TAPERED STEEL TROLLEY POLES AND ACCESSORIES

05510: TAPERED STEEL TROLLEY POLES AND ACCESSORIES PART 1 GENERAL 1.01 DESCRIPTION A. The Vendor shall fabricate, furnish, test and deliver tapered steel trolley poles, including base plates, reinforced hand holes, anchor bolts, nuts and washers, and accessories

More information

SIERRA MODEL 12 X 24 SPECIFICATIONS

SIERRA MODEL 12 X 24 SPECIFICATIONS SIERRA MODEL 12 X 24 SPECIFICATIONS Dimensions: Roof Dimensions 12-0 x 24-0 Column Dimensions (center to center) 9-0 x 21-0 Minimum Clearance 8-0 Shed Roof 1:12 pitch Square Feet Under Roof 288 Columns

More information

MAST ARMS: ALUMINUM, TRUSS TYPE AND DAVIT TYPE

MAST ARMS: ALUMINUM, TRUSS TYPE AND DAVIT TYPE ELECTRICAL SPECIFICATION 1453 DIVISION OF ENGINEERING DEPARTMENT OF TRANSPORTATION CITY OF CHICAGO REVISED MARCH 14, 2013 MAST ARMS: ALUMINUM, TRUSS TYPE AND DAVIT TYPE SUBJECT 1. This specification covers

More information

SECTION STRUCTURAL STEEL

SECTION STRUCTURAL STEEL PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide structural steel shown on the Contract Drawings and as

More information

JONES AIRWAY, LLC CLEVELAND REGIONAL JETPORT SECTION STRUCTURAL STEEL

JONES AIRWAY, LLC CLEVELAND REGIONAL JETPORT SECTION STRUCTURAL STEEL CLEVELAND REGIONAL JETPORT 05 1200-1 PART 1 - GENERAL SECTION 05 1200 STRUCTURAL STEEL 1.1 RELATED SPECIFICATION SECTIONS: A. Bolting of wood to steel, steel anchors for work of other trades, concrete

More information

SECTION TIMBER FLOATS

SECTION TIMBER FLOATS SECTION 06210 PART 1 - GENERAL 1.01 SUMMARY A. This section covers furnishing and installing the timber float framing for the pile guide area, and all other components not specifically mentioned, necessary

More information

02800 SHADE STRUCTURES

02800 SHADE STRUCTURES 02800 SHADE STRUCTURES for PLAY AREAS ****************************************** SPECIFIER: The shade structure shall utilize a four point hypar system with four columns located a minimum of 10 feet from

More information

SECTION METAL STAIRS

SECTION METAL STAIRS SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. Stairs with concrete treads. B. Stairs with metal treads. C. Structural steel stair framing and supports. D. Handrails and guards. 1.02

More information

Commission No Section

Commission No Section Commission No. 1511 Section 05120-1 PART ONE - GENERAL 1.1 DESCRIPTION A. Work Included: Structural steel and grout. Furnish, fabricate, mark for erection identification, pack, crate, or otherwise properly

More information

STANDARD PLAN SYMBOLS & STANDARD LEGEND

STANDARD PLAN SYMBOLS & STANDARD LEGEND EXISTING NEW STANDARD PLAN SYMBOLS & STANDARD LEGEND GENERAL NOTES: DRAINAGE AND EROSION CONTROL NOTES: DRAINAGE AND EROSION CONTROL NOTES (CONTINUED): UTILITY NOTES: STANDARD NOTES - 1 LANDSCAPE NOTES:

More information

SECTION STRUCTURAL STEEL FRAMING

SECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 05 12 00 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // ---// if not applicable to project. Also delete any other item or paragraph

More information

GUIDE SPECIFICATIONS CURA ADJUSTABLE REROOF FRAMING SYSTEMS SECTION REROOFING ADJUSTABLE FRAMING SYSTEM

GUIDE SPECIFICATIONS CURA ADJUSTABLE REROOF FRAMING SYSTEMS SECTION REROOFING ADJUSTABLE FRAMING SYSTEM - --- -- ----..-------~------------------------------------ GUIDE SPECIFICATIONS CURA ADJUSTABLE REROOF FRAMING SYSTEMS SECTION 07415 REROOFING ADJUSTABLE FRAMING SYSTEM PART 1 - GENERAL 1.01 SCOPE A.

More information

SECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT

SECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT SECTION 230548 - VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

SECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system.

SECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system. PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Fusion welded and rackable ornamental steel picket fence system. B. Related sections: 1. Section 03310 Concrete Work for post support. 2. Section 09960

More information

NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS

NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS PART 1 GENERAL 1.01 SUMMARY Section 15140 PIPE HANGERS, This Section includes the furnishing and subsequent installation of: A. Pipe and equipment hangers, supports, and associated anchors B. Equipment

More information

SECTION Permanent Grandstands PART 1 GENERAL 1.1 RELATED DOCUMENTS

SECTION Permanent Grandstands PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 13125 Permanent Grandstands PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification sections,

More information

Division MEDICAL EQUIPMENT SUPPORT SYSTEMS PART 1 GENERAL

Division MEDICAL EQUIPMENT SUPPORT SYSTEMS PART 1 GENERAL Division 11-7010 MEDICAL EQUIPMENT SUPPORT SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. Contractor shall provide medical equipment support systems as indicated on the drawings. Support systems shall be as required

More information

STATE UNIVERSITY CONSTRUCTION FUND. UNIVERSITY CON DIRECTIVE 5-1 Issue date: October 2014

STATE UNIVERSITY CONSTRUCTION FUND. UNIVERSITY CON DIRECTIVE 5-1 Issue date: October 2014 STATE STRUCTION FUND DIRECTIVE 5-1 Issue date: October 2014 STRUCTURAL STEEL 1. General: It is the Fund's policy that the design of the structural steel is the prime responsibility of the project's Structural

More information

SECTION STAINLESS STEEL WALL PANELS

SECTION STAINLESS STEEL WALL PANELS SECTION 07400 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Dry joint, Rainscreen stainless steel wall panel system. 2. Accessories including attachments, clips, sub girts, shims, and fasteners 3.

More information

C. Delegated-Design Submittal: For metal-plate-connected wood trusses indicated to comply with

C. Delegated-Design Submittal: For metal-plate-connected wood trusses indicated to comply with SECTION 06 17 53 PART1 - GENERAL 1.01 A. SUMMARY Section Includes installation of the following products which have been purchased and delivered to the project site under a separate contract: 1. Wood roof

More information

Facility Repairs - MCAS Cherry Point - Tank Farm A SECTION STRUCTURAL STEEL 05/14

Facility Repairs - MCAS Cherry Point - Tank Farm A SECTION STRUCTURAL STEEL 05/14 SECTION 05 12 00 STRUCTURAL STEEL 05/14 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the

More information

Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel ASTM A36, Fy = 36 ksi

Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel ASTM A36, Fy = 36 ksi STRUCTURAL NOTES MATERIAL STRENGTHS Structural Steel Reinforcing Steel Concrete Masonry Structural Lumber Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel

More information

CONTRACT SPECIFICATIONS DISK BEARINGS

CONTRACT SPECIFICATIONS DISK BEARINGS 1.0 DESIGN CONTRACT SPECIFICATIONS DISK BEARINGS 1.1 Scope of Work 1.1.1 This work shall consist of furnishing Multi-Rotational, High Load Disk Bearings and installing Disk Bearing Assemblies at the locations

More information

.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC

.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC 05 12 00 STRUCTURAL STEEL FRAMING Page 1 of 3 1 General 1.1 SECTION INCLUDES.1 Structural steel framing and support members 1.2 RELATED SECTIONS.1 Section 05 50 00 Metal Fabrications 1.3 REFERENCES.1 American

More information

SECTION PRE-ENGINEERED METAL BUILDING

SECTION PRE-ENGINEERED METAL BUILDING SECTION 13121 PRE-ENGINEERED METAL BUILDING PART 1 GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required to design, fabricate, deliver to project site, and erect

More information

SECTION ORNAMENTAL WELDED STEEL FENCING

SECTION ORNAMENTAL WELDED STEEL FENCING SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

A. Section Metal Decking. (05300 in MF95) B. Section Cold Formed Metal Framing. (05400 in MF95)

A. Section Metal Decking. (05300 in MF95) B. Section Cold Formed Metal Framing. (05400 in MF95) SECTION 05 44 00 - PRE-ENGINEERED PRE-FABRICATED COLD-FORMED STEEL TRUSSES (Section 05425 in MasterFormat 1995) PART 1 GENERAL 1.1 SECTION INCLUDES A. Pre-engineered cold-formed steel trusses. B. Cold-formed

More information

A. Provide all wood trusses as indicated on the drawings or as required to do a complete job.

A. Provide all wood trusses as indicated on the drawings or as required to do a complete job. SECTION 06100 - PART ONE GENERAL 1.1 SECTION INCLUDES A. Provide all wood trusses as indicated on the drawings or as required to do a complete job. 1.2 QUALITY ASSURANCE A. Engineering drawings conforming

More information

SECTION ALUMINUM WALKWAY COVERS. A. The requirements of Division 1 specifications shall apply to work specified in the section.

SECTION ALUMINUM WALKWAY COVERS. A. The requirements of Division 1 specifications shall apply to work specified in the section. SECTION 10 5300 ALUMINUM WALKWAY COVERS Part 1 General 1.01 Related Documents A. The requirements of Division 1 specifications shall apply to work specified in the section. 1.02 References A. International

More information

SPECIFICATION FOR PERMANENT BEAM GRANDSTAND WITH INTERLOCK WELDED DECK SYSTEM

SPECIFICATION FOR PERMANENT BEAM GRANDSTAND WITH INTERLOCK WELDED DECK SYSTEM E & D SPECIALTY STANDS, INC. MANUFACTURERS OF QUALITY STANDS AND SEATING 2081 FRANKLIN STREET - P.O. BOX 700 - NORTH COLLINS, NEW YORK 14111 716-337-0161-1-800-525-8515 FAX 716-337-2903 - SALES FAX 716-337-3436

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-05 21 00 (May 2015) --------------------------- Preparing Activity: USACE Superseding UFGS-05 21 13 (August 2009) UFGS-05 21 16 (August 2009) UFGS-05 21 19 (July 2007)

More information

Do not place bundles of deck so as to overload the supporting structure.

Do not place bundles of deck so as to overload the supporting structure. 1/5 1.0 PURPOSE This specification describes the minimum requirements for the design, supply, fabrication and installation of steel roof decking complete with all accessories conforming to the roof system

More information

SECTION ALUMINUM GATES

SECTION ALUMINUM GATES P.O. Box 1058 370 South Athol Rd. Athol, Massachusetts 01331 Phone: (978) 249-7924 Fax: (978) 249-3072 SECTION ALUMINUM GATES PART 1 GENERAL 1.01 SCOPE OF WORK A. The CONTRACTOR shall furnish all labor,

More information

DOUGLAS ELEMENTARY SCHOOL STRUCTURAL STEEL FRAMING

DOUGLAS ELEMENTARY SCHOOL STRUCTURAL STEEL FRAMING SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

2. Clarification: The notice to proceed construction period of 60 days will begin after the Contractor receives all materials and equipment.

2. Clarification: The notice to proceed construction period of 60 days will begin after the Contractor receives all materials and equipment. East Energy Chiller 1 Cooling Tower Addition State Project Number H27-1969 Addendum One June 28, 2012 NOTE: The following amendments, additions, and deletions shall be made to the Construction Documents

More information

SECTION (formerly 05425) PRE-ENGINEERED, PRE-FABRICATED COLD-FORMED STEEL ROOF & FLOOR TRUSSES

SECTION (formerly 05425) PRE-ENGINEERED, PRE-FABRICATED COLD-FORMED STEEL ROOF & FLOOR TRUSSES SECTION 05 44 00 (formerly 05425) PRE-ENGINEERED, PRE-FABRICATED COLD-FORMED STEEL ROOF & FLOOR TRUSSES PART 1 GENERAL 1.1 SUMMARY A. Section includes pre-engineered, pre-fabricated cold-formed steel framing

More information

Park Hill School District South HS Football Venue & Park Hill HS Soccer Venue

Park Hill School District South HS Football Venue & Park Hill HS Soccer Venue SECTION 03 26 14 Permanent Grandstands- Factory computerized welded decking system PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of Contract, including General and Supplementary

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work.

B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work. SECTION 055116 - METAL FLOOR PLATE STAIRS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

BEARING METAL STUD FRAMING

BEARING METAL STUD FRAMING L-1 Section 05410 Long Form Specification LOAD BEARING METAL STUD FRAMING This section includes axially loaded steel studs, with unique slotted top channels, usually of 0.91, 1.2 and 1.5 mm (16, 18, or

More information

1.02 RELATED SECTIONS: Water supply piping, water use piping, electrical, irrigation, foundations, site plans.

1.02 RELATED SECTIONS: Water supply piping, water use piping, electrical, irrigation, foundations, site plans. INC. ENGINEERING/CONSTRUCTION/MANUFACTURING /WWW.CONTAINWATER.COM SPRINGS, TEXAS. 78620 MODEL SPECIFICATION FOR CONTAIN WATER INC. DOME ROOF CORRUGATED STEEL WATER STORAGE TANKS. Part 1 GENERAL 1.01 SECTION

More information

SECTION INDUSTRIAL ACCESS / INSPECTION HATCH. A. Industrial Access / Inspection Hatch: Model AH-710

SECTION INDUSTRIAL ACCESS / INSPECTION HATCH. A. Industrial Access / Inspection Hatch: Model AH-710 Page 1 of 6 PART 1 - GENERAL SECTION 08370 INDUSTRIAL ACCESS / INSPECTION HATCH 1.1 SECTION INCLUDES A. Industrial Access / Inspection Hatch: Model AH-710 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry

More information

SECTION STRUCTURAL STEEL

SECTION STRUCTURAL STEEL SECTION 05120 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this

More information

Northpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017

Northpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017 SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces.

SECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces. PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Handrails and guardrails. 1.2 PERFORMANCE REQUIREMENTS A. General: In engineering railings to withstand structural loads indicated, determine

More information

A. OSHA 1910, Subpart D, Fixed Industrial Ladders. C. ANSI A14.3, Safety requirements for Fixed Ladders

A. OSHA 1910, Subpart D, Fixed Industrial Ladders. C. ANSI A14.3, Safety requirements for Fixed Ladders Page 1 of 5 SECTION 055133 METAL LADDERS (GRABSAFE Ladder Rung Continuation Grips) Part 1. GENERAL 1.1 SECTION INCLUDES A. Specialty custom designed GRABSAFE Ladder Rung Continuation Grips (Patent Numbers

More information

SECTION DECORATIVE METAL FENCES AND GATES

SECTION DECORATIVE METAL FENCES AND GATES SECTION 32 31 19 SPEC WRITER NOTE: Use this section only for NCA projects. Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section

More information

SECTION FABRICATED ENGINEERED STRUCTURES. A. Pre-engineered, shop-fabricated structural steel building with formed purlin framing.

SECTION FABRICATED ENGINEERED STRUCTURES. A. Pre-engineered, shop-fabricated structural steel building with formed purlin framing. PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 13 34 00 FABRICATED ENGINEERED STRUCTURES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1

More information

SECTION STRUCTURE MOUNT RAILING SYSTEM

SECTION STRUCTURE MOUNT RAILING SYSTEM SECTION 05520 STRUCTURE MOUNT RAILING SYSTEM Peak Fall Protection specializes in the design, engineering, fabrication, installation, and certification of fall protection safety systems. Our team of safety

More information

Flotation Docking Systems, Inc.

Flotation Docking Systems, Inc. GENERAL SPECIFICATIONS The following data outlines the design calculations and specifications around which Flotation Docking Systems, Inc. products are constructed. The use of such information for contract

More information

SECTION COLD-FORMED METAL FRAMING

SECTION COLD-FORMED METAL FRAMING SECTION 05.40.00 COLD-FORMED METAL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Cold-formed metal framing for: B. Exterior load-bearing steel stud walls. 1. Interior load-bearing steel stud walls. 2.

More information

SECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Welded System

SECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Welded System SECTION 13096 RADIO FREQUENCY SHIELDING ENCLOSURE RF Welded System Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13096-1 RF WELDED SYSTEM PART 1 GENERAL 1.1 SECTION

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 22 0548 - PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

603 Summit Avenue, Suite 102 Greensboro, N.C Voice/FAX (336)

603 Summit Avenue, Suite 102 Greensboro, N.C Voice/FAX (336) Ricky L. Loman, AIA Architect 603 Summit Avenue, Suite 102 Greensboro, N.C. 27405-7700 Voice/FAX (336) 273-7999 ADDENDUM: Number 1 ISSUED: March 14, 2017 SUBJECT: New Agriculture & Equipment Storage Barn

More information

SECTION 716 SIGN MATERIALS SCOPE

SECTION 716 SIGN MATERIALS SCOPE 716 716.01.01 MATERIALS COVERED SECTION 716 SIGN MATERIALS SCOPE A. This specification covers the kind and quality of materials used in the construction and fabrication of traffic control devices used

More information

PROJECT: 4/30/14 DATE: REVISIONS: 6/10/14 7/28/14 11/3/14 11/12/14 11/14/14 OF 6

PROJECT: 4/30/14 DATE: REVISIONS: 6/10/14 7/28/14 11/3/14 11/12/14 11/14/14 OF 6 4/30/14 C 7/31/2014 4'-6" RAMP TO EXISTING GRADE DRAWN: JW 11/12/2014 AS REQ'D 7'-10 1/2" 7'-10 1/2" 7'-10 1/2" 7'-10 1/2" 2'-0 1/2" 4'-10 1/2" 6" 3'-10" 3'-8" L2X2X1/8 @ 16" OC (TYP) L2X2X1/8 @ 16"

More information

STATEMENT OF SPECIAL INSPECTION FORM

STATEMENT OF SPECIAL INSPECTION FORM Project Title: Permit #: Project Address: STATEMENT OF SPECIAL INSPECTION FORM This Statement of Special Inspections is submitted in fulfillment of the requirements of CBC Sections 1704 and 1705. Special

More information

SECTION 1043 FENCE MATERIAL

SECTION 1043 FENCE MATERIAL SECTION 1043 FENCE MATERIAL 1043.1 Scope. This specification covers the material required in the construction of chainlink fence and woven wire fence. 1043.2 Basis of Acceptance. The basis of acceptance

More information

Sport Systems Canada Inc. Section Angle Framed Bleachers Page 1

Sport Systems Canada Inc. Section Angle Framed Bleachers Page 1 Page 1 Part 1 GENERAL.1.1 Section Includes.1 Design, fabrication, engineering, and installation of continuous angle framed bleacher assembly, including the following:.1 Foundations.2 Galvanized steel framing

More information

SECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS

SECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 SECTION 08 32 20 CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS [OR WOOD] PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,

More information

PRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B

PRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B SECTION 05 5213 - PIPE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

A. Structural Steel: Elements of structural-steel frame, as classified by AISC 303, "Code of Standard Practice for Steel Buildings and Bridges.

A. Structural Steel: Elements of structural-steel frame, as classified by AISC 303, Code of Standard Practice for Steel Buildings and Bridges. SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION ALTERNATING TREAD STEEL STAIRS

SECTION ALTERNATING TREAD STEEL STAIRS SECTION 05 51 33.23 - ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 SCOPE OF WORK Fabricate and Install metal alternating tread stair assemblies in accordance with the requirements set forth in this

More information

1.02 RELATED SECTIONS: Water supply piping, water use piping, electrical, irrigation, foundations, site plans.

1.02 RELATED SECTIONS: Water supply piping, water use piping, electrical, irrigation, foundations, site plans. INC. ENGINEERING/CONSTRUCTION/MANUFACTURING /WWW.CONTAINWATER.COM SPRINGS, TEXAS. 78620 MODEL SPECIFICATION FOR CONTAIN WATER INC. 30 DEGREE ROOF CORRUGATED STEEL WATER STORAGE Part 1 GENERAL 1.01 SECTION

More information