1. Section Steel Doors and Frames. 2. Section Flush Wood Doors 3. Section Aluminum Storefront Doors.

Transcription

1 PROPOSED ALTERATIONS FOR REIMS PINECREST 124, LLC PINECREST, FLORIDA SECTION DOOR HARDWARE PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Mechanical door hardware for the following: B. Related Sections a. Swinging doors. 1. Section Steel Doors and Frames. 2. Section Flush Wood Doors 3. Section Aluminum Storefront Doors. 1.2 SUBMITTALS A. GENERAL REQUIREMENTS: Submit manufacturer s product data for each item of hardware. Include whatever information may be necessary to show compliance with requirements, and instructions for installation and maintenance of operating parts and exposed finishes. B. SCHEDULES: Submit six (6) copies of the finish hardware schedule for approval. Schedule format shall be similar to the one included at the end of Part 3 of this section. Submit a Factory Wiring Diagram for ALL electrical hardware components for the approval of the project Electrical Engineer. C. SAMPLES: At the request of the architect, submit samples of products for approval of design, finish, etc. D. TEMPLATES: Whenever required, furnish templates to the necessary fabricators of other related work, which is to receive finish hardware, such as door and steel door frames and or aluminum doors and frames. E. CATALOG CUTS: Submit six (6) copies of catalog cuts of all products listed in the finish hardware schedule. F. KEYING SCHEDULE: The specific keying requirements should be noted DOOR HARDWARE

2 elsewhere in this schedule. If these requirements are not noted then, it is the supplier s responsibility to submit a keying schedule based on the format listed in the DHI annual Keying Procedures, Systems and Nomenclature. 1.3 QUALITY ASSURANCE A. STANDARDS: Manufacturers and model numbers listed are to establish a standard of quality. Similar items by approved manufacturers, unless otherwise noted, that are equal in design, finish and quality will be accepted upon prior approval of the architect and provided required data and physical samples are submitted at least ten (10) days prior to date of bid. B. QUALIFICATIONS: Hardware supplier must be engaged regularly in contracting work and be staffed to expedite work, the firm shall have been furnishing hardware on similar projects for not less than five years. The supplier must have in his employ a certified Architectural Hardware Consultant (AHC) to periodically inspect and direct detailing, setting, applying of all hardware items. C. FIELD INSPECTION: Inspection of existing doors, frames and hardware is required to evaluate compliance to the Americans with Disabilities Act, (ADA). A written report detailing any such deficiencies shall be forwarded to the Architect five (5) business days prior to bid of project. 1.4 REFERENCES A. ANSI/BHMA designations where used in schedules to describe hardware items or to define quality or function are derived from the following standards and requirements specified elsewhere in this section. 1. BHMA A156.1 Butts and Hinges 2. BHMA A156.3 Exit Devices 3. BHMA A156.4 Door Controls and Closers 4. BHMA A156.5 Auxiliary Locks and Associated Products 5. BHMA A156.6 Architectural Door Trim 6. BHMA A156.7 Template Hinge Dimensions 7. BHMA A Mortise Locks 8. BHMA A Auxiliary Hardware 9. BHMA A Materials and Finishes 10. BHMA A Thresholds 11. BHMA A Door Gasketing and Edge Seal Systems 1.5 DELIVERY STORAGE AND HANDLING DOOR HARDWARE

3 A. MARKING & PACKAGING: Hardware should be required to be sent to the job site in the manufacturers original packages marked to correspond with the approved hardware schedule. B. Some items of hardware may have to be delivered to fabricators for factory installation. (i.e.: Aluminum Storefront). C. Storage and protection of the materials is the responsibility of the General Contractor. Proper storage methods are advised as protection of the material and finish as necessary. 1.6 WARRANTIES A. All door closers shall have a ten (10) year warranty against defects in material and workmanship from the date of occupancy of the project. B. All other products shall have a one (1) year warranty against defects in the material and workmanship from the date of occupancy of the project. C. Exit hardware shall be warranted for a period of three (3) years against defects material and workmanship. PART 2 - PRODUCTS 2.1 ACCEPTABLE PRODUCTS A. The following is a list of acceptable products: Products: Specified Manufacturers: Acceptable Manufacturers: HINGES HAGER LAWERENCE, MCKINNEY PIVOTS RIXON LCN FLUSH BOLTS HAGER IVES, ROCKWOOD, TRIMCO EXIT DEVICES VON DUPRIN CORBIN RUSSWIN, YALE CYLINDERS MATCH LOCKS LOCKS SCHLAGE CORBIN RUSSWIN, SARGENT, YALE PUSH-PULLS HAGER ROCKWOOD, TRIMCO DOOR CLOSERS NORTON, YALE CORBIN RUSSWIN Products: Specified Manufacturers: Acceptable Manufacturers: KICK PLATES HAGER ROCKWOOD, TRIMCO DOOR STOPS McKINNEY ROCKWOOD, TRIMCO THRESHOLDS PEMKO NAT. GUARD, REESE W / S SETS PEMKO NAT. GUARD, REESE B. To the greatest extent possible, obtain materials from one manufacturer. Manufacturers listed above are intended to insure quality and design of the project. Other manufacturers submitted will be acceptable, provided they are equal or exceed standard of quality proposed for this project. DOOR HARDWARE

4 2.2 MATERIALS A. SCREWS & FASTENERS: All screws and fasteners required for the hardware items are listed in the individual hardware sets. Any omission of these items should be reflected in the schedule submitted for approval. B. HINGES: Where hinges are specified unless otherwise noted they shall be of types and sizes as required by ANSI A Size hinges at 4-1/2 inches by 4-1/2 inches or according to manufacturers recommendations. C. PIVOTS: All pivots and/or pivot sets shall be the product of one (1) manufacturer. Sets as noted in the hardware groups shall be matching in design for aluminum storefront doors. The doors as noted in the hardware sets are to have intermediate pivots as well as top pivots. All pivot sets are required to meet ANSI Grade One standards as standard listed in ANSI A156.4, D. FLUSH BOLTS: Provide annual and automatic flush bolts as noted in the hardware sets. All flush bolts are required to meet ANSI A E. LOCKSETS & CYLINDERS: Provide lock sets and cylinders as noted in hardware sets. Lock sets shall meet ANSI A156.2, Grade One operational, Grade Two security, UL listed. Lock cases shall be field reversible. Cylinders shall match existing manufacturer, no substitutions will be allowed. Contractor shall field verify existing cylinder type. F. LOCK TRIM: The design for the lock sets shall match the existing hardware sets. G. EXIT DEVICES: Provide the series and type of exit devices as noted in the hardware sets. These exit devices are required to meet ANSI A156.3 Grade One. All exit devices shall be of one manufacturer. H. DOOR CLOSERS: Provide the series and type of door closers as noted in the hardware sets. These door closers are required to meet ANSI A156.4 Grade One. All closers and power actuated closers shall be of one manufacturer. Plated finish door closers shall have plated arms and brackets. Painted finish door closers shall be powder coated. I. DOOR PLATES: Provide the type and size of these plates as noted in the hardware sets. These items are intended for the use and accessibility as protection of the openings indicated in the hardware schedule. J. DOOR STOPS & HOLDERS: Provide the types as noted in the hardware sets. Any variation in the job site conditions could change the type as specified. This should be reflected in the schedule submitted for approval. K. THRESHOLD & WEATHER-STRIPPING: Provide the types as noted in the DOOR HARDWARE

5 hardware sets. All exterior openings and interior fire rated openings shall have the necessary items to meet the local building code standards. Provide stainless steel screws at all locations. L. SILENCERS: Provide the type required to accommodate the hollow metal frames and wood frames fabricated for the project. 2.3 FINISHES A. Provide the finishes as specified in the hardware schedule. Otherwise, provide matching finishes for the hardware items at each door opening to the greatest extent possible. Refer to the ANSI A for the identification of these finishes. 2.4 KEYING A. Review with the Architect and/or Owner s Representative all keying requirements. Submit key schedule in DHI written format for approval by the Architect and the Owner prior to factory order. B. Each key shall be marked and identified as directed by the Architect using the mechanical impact method of transferring the numerical impression to the key bow. Characters shall be consistent and uniform in their placement, alignment and depth of impression. 2.5 KEY CONTROL A. KEY CABINET: Provide a key control system including envelopes, labels tags, with self locking key clips, receipt forms, three-way visible card index, temporary markers and standard metal cabinet. Provide all of this material from one manufacturer and per that manufacturer s system standard. Provide a system with the capacity for 150% of the number of cylinders and lock sets required for the project. PART 3 - EXECUTION 3.1 INSPECTION A. After installation has been completed, the hardware supplier shall have a qualified Architectural Hardware Consultant (AHC); check the job to determine the proper application of hardware according to the approved hardware schedule and keying schedule. AHC shall also check the operation and adjustment of all hardware items. AHC shall submit a written report of specification compliance to the Architect with the close DOOR HARDWARE

6 out documents required in A. 3.2 INSTALLATION A. Refer to the DHI manual publication for Recommended Locations for Builders Hardware. Comply with all ADA requirements for instruction. Also, coordinate with the door suppliers for these locations. Install all hardware in compliance with manufacturer s instruction and recommendations. Drill and countersink all items which are not factory prepared for fasteners. Cut and fit all thresholds and weather-stripping to profile of door frames. Set threshold in accordance with the application condition. 3.3 ADJUSTING & CLEANING A. At final completion all hardware shall be left clean and free from disfigurement. The contractor shall make a final adjustment to all door closers and other items of hardware. Where hardware is found defective, repair, replace or otherwise correct as directed. 3.4 PROTECTION A. The general contractor is responsible for the proper protection of all items of hardware until final acceptance of the project by the owner and the architect. 3.5 HARDWARE SCHEDULE A. Provide hardware for each door as scheduled and indicated in Door Schedule on Drawings. HARDWARE SET NO. 1 Cylinder master keyed to building system for each sliding door leaf. HARDWARE SET NO. 2 1 Set Pivots CO7031 x Intermediate Pivot CO7321 x Exit Device Type 3-08 x Electromagnetic Lock E08571 x 630 (shear lock) 2 Card Readers By Security System Provider 1 Concealed Closer CO5041 x Threshold J36130 x 36 1 Set Weatherstripping ROY 154 x 17 HARDWARE SET-101 DOOR HARDWARE

7 3 Hinges A5112 x Lockset F07 x Closer C02021 x 110 degrees 3 Silencers L03011 HARDWARE SET Hinges A5112 x Lockset F07 x Electric Strike E09321 x Card Reader by Security System provider 1 Closer C Wall Bumper L02101 x Silencers L03011 HARDWARE SET Hinges A5133 x Privacy Lock F02 x Wall Bumper L02101 x Silencers L03011 END OF SECTION DOOR HARDWARE