INSTALLATION GUIDELINES PREFINISHED SOLID & ENGINEERED WOOD

Size: px
Start display at page:

Download "INSTALLATION GUIDELINES PREFINISHED SOLID & ENGINEERED WOOD"

Transcription

1 Page 1 INSTALLATION GUIDELINES PREFINISHED SOLID & ENGINEERED WOOD Fluent Floors Installation Instructions Prefinished Solid & Engineered Wood Acceptance of Flooring Since wood is a natural product, there will be variations in grain, color and texture. These variations are not to be considered flaws, but a natural characteristic of wood. Inherent in a natural product, there may be imperfections that occur in nature or reveal themselves during the manufacturing process. The accepted standard in the industry allows a defect tolerance and grading variance not to exceed 5%, which may be of manufacturing or natural type. Prior to installation, all floor boards should be inspected. Regardless of if it is a natural or manufacturing defect, boards that have an unacceptable grade, color, finish, texture or grain pattern should not be installed, and should immediately be reported to the seller. The acceptance of the flooring remains the sole and joint responsibility of the installer and end-user. Once the flooring is installed, it has been deemed acceptable by the installer and the enduser. To achieve a uniform appearance across the entire floor, it is critical to blend several cartons of the flooring during installation. Additionally, extra flooring should be retained due to future repairs. It is the responsibility of the installer/end-user to determine if the jobsite subfloor and jobsite conditions are environmentally and structurally acceptable for wood flooring installation (see Minimum Jobsite Requirements). Fluent Floors declines any responsibility for wood floor failure resulting from or connected with sub floor, subsurface, jobsite damage or deficiencies after hardwood flooring has been installed. In addition to the 5% manufacturing defect tolerance, the customer shall order 5%- 7% in addition to the actual square footage needed as allowance for cut-off or waste. For patterned, ornamental or floors with a specific saw grade the cut-off or waste can be higher. Fluent Floors liability shall be solely limited to the replacement of defective products, i.e. materials only in excess of the 5% industry accepted norm, excluding trimming waste allowance. In any case, Fluent Floors shall not be liable for installer s lack of judgement, quality of installation, labor, installation costs or any other consequential losses. Installation guidelines are intended to offer general guidance as it relates to Fluent Floors pre-finished solid or engineered flooring and are NOT a replacement for a professional, certified installer. Fluent Floors wood floors MUST be installed according to the National Wood Flooring Association s (NWFA) installation guidelines in order for Fluent Floors warranty to be valid. The most current publication of the NWFA guidelines are available to all members and a list of local NWFA Certified Professional Installers can be located at Minimum Jobsite Requirements 1. Do not deliver wood flooring to the jobsite or install wood flooring until the building is fully enclosed, heating and air conditioning is in operating condition, and until appropriate required temperature and humidity conditions have been achieved. Appropriate temperature and humidity conditions are defined as those conditions to be experienced in the building after occupancy or those required by wood manufacturer. 2. Wood flooring should be one of the last jobs completed on the construction project. All wet trades including concrete, masonry, plastering, drywall, tile, texturing and painting etc. should be complete. Appropriate required temperature and relative humidity conditions should stabilize before wood flooring is brought in. Limit foot traffic on finished wood flooring.

2 Page 2 3. Evaluate the jobsite for potential problems before installation begins and before wood flooring is delivered to the jobsite. A. Exterior surface drainage should direct water away from the building. B. Basements and crawl spaces must be dry. If power washing is required in the basement, do so before wood flooring is installed and allow subfloor and basement to dry before installing wood flooring. C. Crawl space should be a minimum of 18 (457mm) from ground to underside of joists. Crawl space earth (or thin concrete slab) should be covered 100 percent by a vapor barrier of black polyethylene (minimum 6 mil) or any recommended puncture-resistant membrane, such as Class C, meeting ASTM D1745. Check local codes. See NWFA Installation Guidelines for additional crawl space conditions and follow the local building codes. 4. Note the grade level so that the correct type of flooring and system can be specified for the job. Engineered and floating floors can be appropriate for above-grade, on-grade and below-grade installations. Solid wood flooring can be appropriate for above-grade and on grade installations, but not for below grade installations. If the soil surrounding a structure is three inches or more above the floor of any level, consider that level below grade. This includes walk-out basements. 5. Subfloors (wood or concrete) should be checked by an appropriate method for establishing moisture content. See below for moisture content requirements. 6. After installation, if you choose to protectively cover the floor, cover the floor completely, since some species/ finishes are light-sensitive and uncovered areas may change color. However, covering a glue-down application may not allow some adhesives to properly cure. Follow the flooring and adhesive manufacturer s recommendations. Use a covering material with a vapor permeance (perm rating) of 1 perm or more (tested in accordance with ASTM E96) to avoid trapping moisture/vapor on or within the floor. Any covering should be taped, using a low adhesion tape, to base or shoe moldings (test adherence and verify it will not damage finishes on these surfaces as well). For floor protection use only a brown kraft type paper or Ram-board product that will allow the flooring to breathe. Do not use cardboard as it can leave marks in the finish. Do not tape to finished flooring. When taping paper or sheets together, tape them to each other, not to the floor. As in all installations, at completion of job, inspect flooring from a standing position. Acclimation/ Conditioning 1. Ensure that the building is enclosed. 2. Verify that the building is maintained at the required conditions for temperature and humidity. 3. Heating and/or air conditioning systems should be operating at least five days preceding installation to promote proper acclimation and should be maintained during and after installation. 4. Prior to installation, ensure that wood flooring is within acceptable range of moisture content with the wood subfloor. Moisture content of subflooring should not exceed 12%. For plank solid or engineered flooring (3 or wider), there should be no more than 2 percent difference in moisture content between properly acclimated/conditioned wood flooring and subflooring materials. Moisture content readings should be performed and logged. Forty readings per 1000 square feet, taken from various bundles/ boards throughout. Rule for acclimation/conditioning: Solid Pre-finished Flooring- Acclimate/condition the flooring to the environment. Engineered Flooring- Condition the environment to the wood flooring. For solid and solid pre-finished wood - Acclimation can be facilitated by breaking the floor units into small lots and/or opening the packaging. A common practice is to cross stack the materials with spacers made of a synthetic material such as plastic builder shims. Do not use wood, due to tannin bleed (¾ to 1 sticks) between each layer of flooring to allow air circulation on all sides of all boards.

3 Page 3 For engineered wood Ensure that the temperature and relative humidity of the structure where flooring is to be put into use is within the range tolerance stated by the manufacturer. Check moisture content of flooring and subfloor at time of delivery. No more than 2% variance in moisture content should exist. Packaging should be opened on each end (if applicable) and allowed to condition for a minimum of 72 hours. For wider widths or thicker wear layers, more conditioning time may be necessary but care should be taken that the boards do not begin to swell or shrink and distort due to higher or lower relative humidity. Careful monitoring of moisture content, appearance of flooring and environment should be performed diligently. Acclimate/condition flooring for a minimum of seven days for solid products, and three days for engineered. There is no given maximum in stated time for proper acclimation. While it takes time to acclimate a product, the most important aspect is that the materials reach a moisture content that is in equilibrium with its expected use. When wood is neither gaining nor losing moisture, equilibrium moisture content (EMC) has been reached. Acclimate/ condition the materials as long as necessary to accomplish this task, taking the necessary moisture readings to indicate when the materials have reached the proper moisture content and when no further changes occur. See NWFA Installation Instructions for additional information for acclimating wood flooring. Follow the moisture meter manufacturer s instructions for proper moisture content readings. Supplemental heating/cooling and humidification and/or dehumidification will be required at different times of the year, in nearly every climate in North America. This is especially important for the Mountain West region which is considered a high-altitude, dry climate. There are additional requirements for radiant heat installations. Fluent pre-finished solid flooring and engineered flooring products require temperature to be maintained between 60 and 80 degrees Fahrenheit and 35-55% relative humidity. Failure to comply with these requirements may result in irreversible structural damage to the flooring and void related warranties. Note: Not properly acclimating wood flooring may cause excessive expansion, shrinkage, dimensional distortion or structural damage. The worst case scenario is one in which wood flooring is stored at the jobsite in an uncontrolled environment, then immediately installed. This is especially true when the materials are stored in an area that is subject to excessive moisture and humidity conditions. Acclimation outside of the area in which the wood is to be installed does no good at all; in fact, it is likely harmful to store wood flooring at the jobsite under conditions that don t reflect expected normal or required environmental conditions. Wood Subfloor Specifications 1. Typically both ¾ CD Exposure 1 plywood and OSB Exposure 1 subfloor panels are appropriate subflooring materials, but the proper thickness of the material will be determined by the factors noted in the NWFA Installation Guide. 2. Wood subfloors must be flat, clean, dry, structurally sound, free of squeaks and free of protruding fasteners. See NWFA Installation Guidelines for additional tolerances and requirements. A. Flatness: For nail down installation (1½ or longer fastener) the subfloor should be flat to within ¼ in 10 feet or 3/16 in 6 feet radius. For glue-down installations and installations using mechanical fasteners of less than 1½, the subfloor should be flat to within 3/16 in 10 feet or 1/8 in 6 feet radius. If peaks or valleys in the subfloor exceed the tolerances specified above, sand down the high spots and fill the low spots with a levelling compound or other material approved for use under wood flooring. B. Clean: Ensure all dust, debris and residue (including concrete contaminates that may affect adhesive bond) are properly cleaned and removed from the subfloor. C. Dry: Ensure that the moisture content does not exceed 12%. D. Structurally Sound: Inspect the subfloor carefully. If there is movement or squeaks in the subfloor, refasten the subfloor to the joists in problem areas.

4 Page 4 E. Protruding fasteners are easily remedied by driving those fasteners deeper into the subfloor. Moisture Testing Wood Subfloors Follow the meter manufacturer s recommendations to get an accurate reading from the wood floor. Apply the necessary adjustment tables, conversion charts or settings for various species. Test for moisture at several locations in the room a minimum of 20 per 1,000 square feet and average the results. Document all results. A high reading in one area indicates a problem that must be corrected. Pay special attention to exterior and plumbing walls. Concrete Subfloor Note: All tests give a result at the time the test is done and in general give you the ability to start or not start a job. These tests do not give a permanent condition of your substrate, but merely a at the time the test was performed indication. A. The concrete must be a minimum of 30 days old before testing begins. B. Qualitative Moisture Tests: Electrical Impedance Test and Electrical Resistance Test (Moisture Meter). Follow meter manufacturer s instructions. Use moisture meters designed specifically for concrete moisture testing. Test within the body of the slab (electrical resistance), as well as at the surface (electrical impedance). These testing methods are not recognized by any standard and should not be used for the purpose of accepting or rejecting a floor. These electronic tests are useful survey tools to broadly evaluate the relative moisture conditions of a slab and to select locations for quantitative moisture tests. If the moisture meters indicate the presence of excessive moisture, as per wood flooring or meter manufacturer s recommendations, further (quantitative) testing is required using relative-humidity testing (ASTM F2170), calcium chloride testing (ASTM F1869) or calcium carbide (CM) testing (ASTM D4944 and MilSpec CRD-C154-77). See NWFA Installation Guidelines for additional acceptable quantitative testing methods. Installation Guidelines Solid Pre-finished Installation Methods Nail Down, Nail with Glue Assist 1. Floor preparation: Refasten any loose areas of subfloor and clean the subfloor by sweeping, scraping, etc., as necessary. With frame construction, mark location of joists on perimeter walls so that starting runs and finishing runs, which require face nailing, can be nailed into joists. Marking also locates the joists for plank flooring installation. 2. Unfinished and factory-finished solid strip and solid plank flooring should be installed perpendicular to the joists or on a diagonal for any single layer subfloor. See NWFA Installation Guidelines for exceptions. 3. Before installing wood flooring, use an approved vapor retarder such as Forti-Fiber Aqua Bar B, lapped 2-4 along the edge seams. This retards moisture movement from below. Extend the felt/building paper completely to the walls. It is necessary to fasten the felt to the subfloor. 4. Wall Line Layout Choose a starting wall according to the most aesthetically or architecturally important elements in the room, taking into consideration fireplaces, doors, cabinets and transitions, as well as the squareness of the room. The starting wall will often be the longest unbroken wall in the room. Snap a working line parallel to the starting wall, allowing ¾ expansion space between the starting wall and the edge of the first strip or plank run. As a general rule, a ¾ expansion space must be left around the perimeter and at all vertical obstructions.

5 Page 5 Random-width plank is laid out with alternating courses varying by widths. Start with the widest board, then the next width, etc., and repeat the pattern. Lay one row of strip or plank along the entire length of the working line. Top-nail and blind-nail the first row (hand-nail if necessary), using appropriate fasteners. Denser species may require pre-drilling. Each succeeding row should be blind-nailed with the nailing machine wherever possible. At the finishing wall and other obstructions, it may be necessary to blind-nail by hand until top nailing is required. Racking rule of thumb: Avoid H patterns. Stagger end joints of boards row to row a minimum of 6 for strip flooring, 8-10 for 3 to 5 planks, and for planks wider than 5, stagger as much as possible with minimal or no H joints. To minimize expansion on floors wider than 20 feet, more or less spacing between rows may be needed, depending on geographical area, interior climate control and time of the year. Where spacing is required: Use a washer or removable spacer to leave additional space every few rows and/or start in center of room and work out to both sides. Do not use spacers that may cause damage on factory-finished products. Nailing: Blind-nail through the tongue using 1½ to 2" fasteners. Use 1½ fasteners with ¾ plywood subfloor direct to concrete slab. Face-nail boards where needed using 6d-8d casing or finish nails. Fasteners should be spaced every 6-8 on blind nailing, or every on face-nailing. Blind-nail, face-nail or use wood floor adhesive, as necessary, to complete the final rows. In board widths over 5, Fluent Floors recommends using a nail down with glue assist method. Follow NWFA acceptable nailing schedule and supplement mechanical fastening with Bona R850-T. Bona R580 can be spread by trowel over the entirety of the subfloor to act as a vapor barrier. See for manufacturer s instructions. The use of subfloor or construction adhesive is not recommended. See NWFA Installation Guidelines for additional layout methods. Engineered Installation Methods Nail, Nail with Glue Assist, Full Surface Glue-Down, Float 1. Engineered wood flooring can be installed directly to screeds, provided the engineered flooring is a minimum of ¾ thick. For engineered flooring less than ¾ thick, the screed system must be overlaid with proper subflooring. (See NWFA Installation Guidelines) 2. Fluent Floors pre-finished engineered flooring should be installed perpendicular to the joists or on a diagonal for any single layer subfloor. 3. Random-width plank is laid out with alternating courses varying by widths. Start with the widest board, then the next width, etc., and repeat the pattern. 4. Choose a starting wall according to the most aesthetically or architecturally important elements in the room, taking into consideration fireplaces, doors, cabinets and transitions, as well as the squareness of the room. The starting wall will often be the longest unbroken wall in the room. 5. Glue-down pre-finished engineered plank Test the substrate for moisture. Excessive/elevated moisture should not be present. The subfloor should be within acceptable moisture content before installing. If a moisture barrier sealer is needed, Fluent recommends either a full surface glue down using Bona R851 or nail down with a glue assist using Bona R Bona R580 can be spread by trowel over the entirety of the subfloor to act as a vapor barrier. Follow NWFA acceptable nailing schedule and supplement mechanical fastening with Bona R850-T. Follow the adhesive manufacturer s guidelines for application instructions. Expansion space should be left around the perimeter. The expansion space should be a minimum of the thickness of the product being installed. Snap a working line parallel to the starting wall, the width of the board, plus the tongue and recommended expansion space.

6 Page 6 Install a starter board along the edge of the working line and begin installation. Lay one row of plank in the adhesive along the length of the working line. This will either need face nails to hold in place, or it should be weighted overnight until glue is set before continuing. The tongue side of the flooring faces the direction in which you are installing. Fluent recommends the use of Bona R851 for full surface glue-down applications. See for product details and instructions. Follow the installation procedure recommended by the adhesive manufacturer, which includes subfloor moisture content, spread rate, trowel size, open time, working time and flash time as necessary. Spread the adhesive as instructed up to and along the working line. Distribute lengths, avoiding H patterns and other discernible patterns in adjacent runs. Stagger end joints of boards row to row a minimum of 6 for strip flooring, 8-10 for 3 to 5 plank, and 10 for planks wider than 5. Fluent does not recommend the use of tape at any time to maintain a tight floor. Use straps or tensioners. 6. Mechanically fastened strip and plank. If necessary, add a vapor retarder. Snap a working line parallel to the starting wall, allowing expansion space as specified by the manufacturer. Lay one row of plank along the entire length of the working line. Top-nail and blind-nail the first row (hand-nail if necessary), using appropriate fasteners. Denser species may require pre-drilling. Each succeeding row should be blind-nailed wherever possible. a. Typical: Narrow crowned (under 3/8 ) 1-1½ staples or 1-1¼ hardwood flooring cleats designed for engineered flooring, spaced as recommended by the manufacturer. b. Typical: Every 3-4 with staples, every 4-6 with cleats, and within 1-2 of end joints. Use appropriate size fastener for top nailing first row, last row and any area where blind nailer will not fit. Add each additional row of flooring. Distribute lengths, avoiding H patterns and other discernible patterns in adjacent runs. Stagger end joints at least three times the width of the boards, as product allows. During installation of flooring pieces, push or gently tap boards flush to the previous row. Tap against the tongue; tapping the groove may damage the edge. To prevent damage to the finish, avoid tapping the face of the board with a rubber mallet. In board widths over 5, Fluent recommends using a nail down with glue assist method. Follow the NWFA acceptable nailing schedule and supplement mechanical fastening with Bona R850-T. Bona R580 can be spread by trowel over the entirety of the subfloor to act as a moisture barrier sealer. See for manufacturer s instructions. The use of subfloor or construction adhesive is not recommended. Please note that thinner engineered products may require additional underlayment for wider joist spacing (19 +), along with either a full surface glue down, or a glue down with nail assist method. See NWFA Installation Instructions for underlayment requirements. 7. Floating engineered flooring. Subfloor flatness is critical to the success of a floating floor installation. Test the substrate for moisture. Excessive/elevated moisture should not be present. The subfloor should be within acceptable moisture content before installing. If necessary, add vapor retarder. Expansion space should be left around the perimeter. The expansion space should be a minimum of the thickness of the product being installed. Typical: Subfloors are covered with a resilient material, foam underlayment or cork. Follow manufacturer's instructions for correct materials and thickness. Typical: Floating engineered flooring is edge-glued or edge-attached with a self-locking mechanism. For edge-glued products use a glue such as Tite-Bond Tongue and Groove Flooring Glue. Do not use an expanding wood glue.

7 Page 7 Starter boards should be aligned with the groove side and end against the starting wall. Tapping block should be used against tongue only. Stagger end joints at least three times the width of the boards, as product allows. Chain of Custody Disclaimer It is the responsibility for all parties involved in the acquisition of this flooring material to pass this document along to the installer and the end-user. This includes, but is not limited to retailers, dealers, distributors, designers, architects or other specifiers. THIS DOCUMENT SUPERSEDES ALL PREVIOUSLY DATED INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS SOLID & ENGINEERED UNFINISHED / PRE-FINISHED

INSTALLATION INSTRUCTIONS SOLID & ENGINEERED UNFINISHED / PRE-FINISHED ACCEPTANCE OF FLOORING As wood is a natural product, there will be variations in grain, color and texture. These variations are not to be considered flaws, but a natural characteristic of wood. Inherent

More information

Installation Instructions

Installation Instructions Installation Instructions The Traditional South American Exotic collections by Elof Hansson can be nailed down, on or above grade. Job site preparation: - If necessary, remove furniture and appliances

More information

Section III Installation Guidelines & Methods Page Chapter 7 Parquet Installation 30 Chapter 8 Engineered Wood Flooring Installation 34 Chapter 9

Section III Installation Guidelines & Methods Page Chapter 7 Parquet Installation 30 Chapter 8 Engineered Wood Flooring Installation 34 Chapter 9 Section III Installation Guidelines & Methods Page Chapter 7 Parquet Installation 30 Chapter 8 Engineered Wood Flooring Installation 34 Chapter 9 Solid Strip and Plank Flooring Installation 37 Chapter

More information

SOLID HARDWOOD PLANK. Product Use & Installation Options. Before Installation Product Inspection & Site Preparation. 18mm Solid hardwood flooring

SOLID HARDWOOD PLANK. Product Use & Installation Options. Before Installation Product Inspection & Site Preparation. 18mm Solid hardwood flooring INSTALLATION INSTRUCTIONS SOLID HARDWOOD PLANK 18mm Solid hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION ABODE floors must be installed in accordance with

More information

L.W. Mountain, Inc Dundee Avenue Suite C Elgin, IL Phone: Fax:

L.W. Mountain, Inc Dundee Avenue Suite C Elgin, IL Phone: Fax: L.W. Mountain, Inc. 1615 Dundee Avenue Suite C Elgin, IL. 60120 Phone: 847-888-9966 Fax: 847-888-6699 Engineered Wood Installation Guidelines Wood is a natural product and will vary in shade or pattern

More information

Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6

Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6 Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6 Installing a Subfloor Over Concrete 27 24 National Wood Flooring

More information

The use of wood putty, wood filler and wood stain for enhancement of the flooring should be accepted as normal.

The use of wood putty, wood filler and wood stain for enhancement of the flooring should be accepted as normal. 3/4 SOLID HARDWOOD STRIP AND PLANK FLOORING INSTALLATION INSTRUCTIONS FOR MECHANICALLY FASTENED, STAPLE, NAIL OR CLEAT APPLICATIONS I. GENERAL INFORMATION Owner/Installer Responsibility: Beautiful hardwood

More information

L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only*

L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only* L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only* Inspect the job site carefully before you begin the installation. Some conditions require specific installation

More information

Installation Guidelines

Installation Guidelines Installation Guidelines BoardHouse, in this document, seeks to offer recommendations that assist in the installation of our engineered wood flooring products; the following pages are guidelines only. It

More information

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLER/OWNER RESPONSIBILITY: Inspect all flooring material carefully for correct product and visible defects BEFORE INSTALLALATION. Warranties do not cover visible defects

More information

ANTIQUED SOLID / SOLID HARDWOOD

ANTIQUED SOLID / SOLID HARDWOOD INSTALLATION INSTRUCTIONS ANTIQUED SOLID / SOLID HARDWOOD 18mm solid hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION KENTWOOD floors must be installed in accordance

More information

Installation Guidelines: Magnolia

Installation Guidelines: Magnolia Installation Guidelines: Magnolia 3/8 Engineered Hardwood Staple Down Installation ATTENTION Inspect ALL materials carefully BEFORE Warranties DO NOT cover materials with visible defects once they are

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLER/OWNER RESPONSIBILITY Inspect all flooring material carefully for correct product and visible defects BEFORE INSTALLALATION. Warranties do not cover visible defects once

More information

9.5, 10, 10.5 & 12mm. Product Use & Installation Options. Engineered hardwood flooring INSTALLATION INSTRUCTIONS

9.5, 10, 10.5 & 12mm. Product Use & Installation Options. Engineered hardwood flooring INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 9.5, 10, 10.5 & 12mm Engineered hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION ABODE floors must be installed in accordance with

More information

COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION

COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION! IMPROPER INSTALLATION WILL VOID WARRANTY. STOP! WPC Engineered Vinyl Flooring

More information

Stratos/Gravity/Veneto

Stratos/Gravity/Veneto Stratos/Gravity/Veneto PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION. PurParket floors must be installed in accordance with the following instructions. Failure to do so may

More information

to do so may void the product warranty.

to do so may void the product warranty. INSTALLATION INSTRUCTIONS for ENGINEERED HARDWOOD FLOORS Species: Red Oak, White Oak, Hard Maple, Hickory. These products can be installed using the following methods: MECHANICALLY fastened to an approved

More information

HIGUERA HARDWOODS SOLID STRAND WOVEN FLOORING PRE-INSTALLATION JOBSITE REQUIREMENTS

HIGUERA HARDWOODS SOLID STRAND WOVEN FLOORING PRE-INSTALLATION JOBSITE REQUIREMENTS HIGUERA HARDWOODS SOLID STRAND WOVEN FLOORING PRE-INSTALLATION JOBSITE REQUIREMENTS Carefully examine the wood flooring prior to installation for color, finish and quality. Ensure adequate lighting for

More information

Pry Bar or Pull bar Hammer Spacing Wedges Rubber Mallet Safety Equipment (Goggles and Mask)

Pry Bar or Pull bar Hammer Spacing Wedges Rubber Mallet Safety Equipment (Goggles and Mask) strand at ease installation instructions strand at ease installation instructions: ECOFINISHES RECOMMENDS USING THE SERVICES OF A PROFESSIONAL HARDWOOD FLOORING INSTALLER. READ THESE INSTRUCTIONS THOROUGHLY

More information

SINCE 1995 CONSTRUKT / SUITE LINE INSTALLATION GUIDE

SINCE 1995 CONSTRUKT / SUITE LINE INSTALLATION GUIDE CONSTRUKT / SUITE LINE INSTALLATION GUIDE We strive to offer our customers the highest quality bamboo flooring. Please carefully read this installation guide to ensure satisfactory results from your floor.

More information

Part 1. PRODUCT USE & INSTALLATION OPTIONS

Part 1. PRODUCT USE & INSTALLATION OPTIONS Part 1. PRODUCT USE & INSTALLATION OPTIONS 3 This floor may be installed: On or above grade only With nail down installation Over OSB or plywood subfloor This floor should not be installed: With floating

More information

Part 1. PRODUCT USE & INSTALLATION OPTIONS

Part 1. PRODUCT USE & INSTALLATION OPTIONS Part 1. PRODUCT USE & INSTALLATION OPTIONS 3 This floor may be installed: On or above grade With nail down installation only Over OSB or plywood subfloor This floor may not be installed over radiant heat

More information

WEST FLOORING & DESIGN (WFD)

WEST FLOORING & DESIGN (WFD) READ ALL OF THESE INSTRUCTION THROUGHLY BEFORE BEGININNING INSTALLATION. IN ADDITION TO THESE INSTRUCTIONS, WE RECOMMEND THAT THE INSTALLER FOLLOW ALL INSTALLATION GUIDELINES SET FORTH BY THE NATIONAL

More information

INSTALLATION GUIDELINES Signature Naturals PureForm Solid Strip Bamboo Flooring

INSTALLATION GUIDELINES Signature Naturals PureForm Solid Strip Bamboo Flooring INSTALLATION GUIDELINES Signature Naturals PureForm Solid Strip Bamboo Flooring Important Product Line Notes: Check Teragren.com for the latest updates to our Installation Guidelines Teragren PureForm

More information

INSTALLATION GUIDELINES

INSTALLATION GUIDELINES INSTALLATION GUIDELINES Visions Oil Brushed, Wide plank Xcora Strand Bamboo Flooring Important Product Line Notes: Check Teragren.com for the latest updates to our Installation Guidelines Visions Bamboo

More information

CLICK TOGETHER ENGINEERED LONGSTRIP HARDWOOD FLOORING CLICK TOGETHER CORK FLOORING CLICK TOGETHER BAMBOO FLOORING

CLICK TOGETHER ENGINEERED LONGSTRIP HARDWOOD FLOORING CLICK TOGETHER CORK FLOORING CLICK TOGETHER BAMBOO FLOORING INSTALLATION INSTRUCTIONS CLICK TOGETHER ENGINEERED LONGSTRIP HARDWOOD FLOORING CLICK TOGETHER CORK FLOORING CLICK TOGETHER BAMBOO FLOORING PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE

More information

20mm wide plank engineered hardwood flooring

20mm wide plank engineered hardwood flooring INSTALLATION INSTRUCTIONS CHEVRON HERRINGBONE 20mm wide plank engineered hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION KENTWOOD floors must be installed

More information

MILLTOWN. Product Use & Installation Options. 12mm engineered hardwood flooring INSTALLATION INSTRUCTIONS

MILLTOWN. Product Use & Installation Options. 12mm engineered hardwood flooring INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS MILLTOWN 12mm engineered hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION KENTWOOD floors must be installed in accordance with the

More information

INSTALLATION INSTRUCTIONS for ENGINEERED HARDWOOD FLOORS

INSTALLATION INSTRUCTIONS for ENGINEERED HARDWOOD FLOORS INSTALLATION INSTRUCTIONS for ENGINEERED HARDWOOD FLOORS Species: Red Oak, White Oak, Hard Maple, Hickory. Width: 5 or 6 Thickness: 3/4 Length: Random These products can be installed using the following

More information

CLICK TOGETHER. Click together engineered longstrip hardwood flooring Click together cork flooring Click together bamboo flooring

CLICK TOGETHER. Click together engineered longstrip hardwood flooring Click together cork flooring Click together bamboo flooring CLICK TOGETHER Click together engineered longstrip hardwood flooring Click together cork flooring Click together bamboo flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION

More information

RECOMMENDED FASTENERS & Nailing SCHEDULE... 8 SERPENTINE GLUE-ASSIST... 9 INSTALLATION... 9

RECOMMENDED FASTENERS & Nailing SCHEDULE... 8 SERPENTINE GLUE-ASSIST... 9 INSTALLATION... 9 Product Use & Installation Options...3 Before Installation...4 INSTALLER S / CUSTOMER S RESPONSIBILITY... 4 SITE PREPARATION... 4 CLIMATE CONTROL... 5 MOISTURE CONTENT... 6 SUBFLOOR PREPARATION... 6 RACKING...

More information

CONTENTS MOISTURE REQUIREMENTS AND MOISTURE TESTING SECTION II SUBFLOOR GUIDELINES & SPECIFICATIONS

CONTENTS MOISTURE REQUIREMENTS AND MOISTURE TESTING SECTION II SUBFLOOR GUIDELINES & SPECIFICATIONS CONTENTS SECTION I GENERAL GUIDELINES CHAPTER 1 JOBSITE CONDITIONS CHAPTER 2 ACCLIMATION CHAPTER 3 MOISTURE REQUIREMENTS AND MOISTURE TESTING SECTION II SUBFLOOR GUIDELINES & SPECIFICATIONS CHAPTER 4 WOOD

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! Glueless Hardwood & Bamboo Flooring Installation Instructions ATTENTION! READ BEFORE INSTALLING! COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual

More information

CHEVRON HERRINGBONE. 20mm engineered hardwood flooring INSTALLATION INSTRUCTIONS

CHEVRON HERRINGBONE. 20mm engineered hardwood flooring INSTALLATION INSTRUCTIONS CHEVRON HERRINGBONE 20mm engineered hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION KENTWOOD floors must be installed in accordance with the following instructions.

More information

WPC Vinyl Floor Installation Guide

WPC Vinyl Floor Installation Guide WPC Vinyl Floor Installation Guide Introduction This guide will take you through the necessary steps to install your Bel-Air WPC Vinyl Flooring. Make sure to carefully read through this guide so that you

More information

J.J. Haines & Co., Inc.

J.J. Haines & Co., Inc. Subfloor Guide for Hardwood Ask any quality wood flooring contractor, and he'll tell you that your hardwood installation is only as good as the subfloor you're installing over. Before the wood is delivered

More information

SECTION WOOD STRIP FLOORING

SECTION WOOD STRIP FLOORING SECTION 096429 WOOD STRIP FLOORING PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. 1.2 SECTION

More information

747 North La Brea Avenue Los Angeles, California Tel: Fax:

747 North La Brea Avenue Los Angeles, California Tel: Fax: Installation Information for Wood Concepts Engineered Flooring Attention Inspect all materials carefully before installation. Warranties do not cover materials with visible defects once they are installed.

More information

Soho Series. Soho Series 12.3mm V-Groove Engineered Laminate Flooring GENERAL INSTALLATION GUIDE

Soho Series. Soho Series 12.3mm V-Groove Engineered Laminate Flooring GENERAL INSTALLATION GUIDE Soho Series Soho Series 12.3mm V-Groove Engineered Laminate Flooring GENERAL INSTALLATION GUIDE Wood is hydroscopic, it will absorb and expel moisture based on its environment. A temperature of 60-75 F

More information

INSTALLATION YANCHI BAMBOO FLOORING INSTALLATION GUIDE PLEASE READ BEFORE INSTALLING GENERAL PRECAUTIONS, WHICH FORM PART OF WARRANTY CONDITIONS

INSTALLATION YANCHI BAMBOO FLOORING INSTALLATION GUIDE PLEASE READ BEFORE INSTALLING GENERAL PRECAUTIONS, WHICH FORM PART OF WARRANTY CONDITIONS YANCHI BAMBOO FLOORING INSTALLATION GUIDE PLEASE READ BEFORE INSTALLING INSTALLATION PLEASE READ THOROUGHLY BEFORE BEGINNING INSTALLATION. THESE INSTALLATION INSTRUCTIONS ARE SPECIFICALLY INTENDED FOR

More information

INSTALLATION IMPORTANT INSTALLER/OWNER RESPONSIBILITY TOOLS & EQUIPMENT NEEDED FOR INSTALLATION PRE-INSTALLATION PROCEDURES & JOBSITE CONDITIONS

INSTALLATION IMPORTANT INSTALLER/OWNER RESPONSIBILITY TOOLS & EQUIPMENT NEEDED FOR INSTALLATION PRE-INSTALLATION PROCEDURES & JOBSITE CONDITIONS IMPORTANT INSTALLATION It is important that you read & understand the following information and instructions in their entirety before proceeding with installation. Please thoroughly inspect all Flooring

More information

Important Information Before You Begin

Important Information Before You Begin INSTALLATION GUIDELINES ATTENTION! READ BEFORE INSTALLING. FAILURE TO FOLLOW GUIDELINES WILL RESULT IN PRODUCT DAMAGE AND/OR VOID ALL WARRANTIES. Important Information Before You Begin It is EXTREMELY

More information

Important Information Before You Begin

Important Information Before You Begin INSTALLATION GUIDELINES ATTENTION! READ BEFORE INSTALLING. FAILURE TO FOLLOW GUIDELINES WILL RESULT IN PRODUCT DAMAGE AND/OR VOID ALL WARRANTIES. Important Information Before You Begin It is EXTREMELY

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! ATTENTION! READ BEFORE INSTALLING! Uniclic Glueless Floating Floor Installation Instructions COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual

More information

ENGINEERED. 12mm engineered hardwood flooring INSTALLATION INSTRUCTIONS

ENGINEERED. 12mm engineered hardwood flooring INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS ENGINEERED 12mm engineered hardwood flooring PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION KENTWOOD floors must be installed in accordance with the

More information

Solid Unfurled Bamboo Flooring Installation Instructions

Solid Unfurled Bamboo Flooring Installation Instructions Solid Unfurled Bamboo Flooring Installation Instructions WARRANTY COVERAGE MAY BE LOST DUE TO FAILURE TO STRICTLY ABIDE BY ALL INSTALLATION INSTRUCTIONS AND RECOMMENDATIONS IN THIS MANUAL. THIS INCLUDES

More information

H A R D W O O D F L O O R I N G 1

H A R D W O O D F L O O R I N G 1 HARDWOOD FLOORING 1 HARDWOOD FLOORING Installation Guidelines This document covers the installation of Revival European Oak Engineered Hardwood Flooring. Please read carefully. IMPORTANT: All pre-finished

More information

LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING

LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s

More information

Part 1. PRODUCT USE & INSTALLATION OPTIONS

Part 1. PRODUCT USE & INSTALLATION OPTIONS Part 1. PRODUCT USE & INSTALLATION OPTIONS 3 This floor may be installed: On, above or below grade With glue down, nail down or float installation Over OSB, plywood or concrete subfloor This floor may

More information

SECTION WOOD GYMNASIUM FLOORING

SECTION WOOD GYMNASIUM FLOORING HORNER VARI-CUSHION SYSTEM Page 1 of 3 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general, of

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! ATTENTION! READ BEFORE INSTALLING! Solid Hardwood & Bamboo Flooring Installation Instructions COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual

More information

LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING

LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s satisfaction.

More information

Greenwood Flooring International Engineered Hardwood Flooring Installation Instructions

Greenwood Flooring International Engineered Hardwood Flooring Installation Instructions Greenwood Flooring International Engineered Hardwood Flooring Installation Instructions READ ALL OF THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. IN ADDITION TO THESE INSTRUCTIONS, WE RECOMMEND

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS for Engineered Hardwood Section 1: INSTALLER / OWNER RESPONSIBILITIES Hardwood flooring is a product of nature and its inherent beauty stems from the fact that each piece is unique

More information

Legacy flooring Fitting Instructions

Legacy flooring Fitting Instructions Legacy flooring Fitting Instructions Attention Inspect all materials carefully before installation. Warranties do not cover materials with visible defects once they are installed. The natural characteristics

More information

The use of stain, filler or putty for correction is considered a normal practice and a routine part of installation.

The use of stain, filler or putty for correction is considered a normal practice and a routine part of installation. 3/4 Solid Hardwood Flooring Installation Instructions Solid Hardwood Flooring can be installed over most properly prepared subfloors, making them suitable for installation on or above grade levels where

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! Engineered Hardwood & Bamboo Flooring Installation Instructions ATTENTION! READ BEFORE INSTALLING! COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual

More information

Please read and review installation instructions completely before proceeding with the actual installation.

Please read and review installation instructions completely before proceeding with the actual installation. INSTALLATION INSTRUCTIONS Important / Read First Please read and review installation instructions completely before proceeding with the actual installation. Owner / Installer responsibility The installer

More information

Part 1. PRODUCT USE & INSTALLATION OPTIONS

Part 1. PRODUCT USE & INSTALLATION OPTIONS Part 1. PRODUCT USE & INSTALLATION OPTIONS 3 This floor may be installed: On, above or below grade With glue down, nail down or float installation Over OSB, plywood or concrete subfloor This floor may

More information

Higuera Hardwoods Prefinished Engineered Bamboo Flooring Installation Instructions

Higuera Hardwoods Prefinished Engineered Bamboo Flooring Installation Instructions Higuera Hardwoods Prefinished Engineered Bamboo Flooring Installation Instructions PRE-INSTALLATION JOBSITE REQUIREMENTS Carefully examine the wood flooring prior to installation for color, finish and

More information

For Ideal Living. Installation Instruction. Maintenance Instruction. Product Warranty.

For Ideal Living. Installation Instruction. Maintenance Instruction. Product Warranty. For Ideal Living Installation Instruction Maintenance Instruction Product Warranty www.idealwood.ca Part 1, Pre-installation: A, Responsibility of customers and installers: It is a highly recommendation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLER/OWNER RESPONSIBILITIES Hardwood flooring is a product of nature and its inherent beauty stems from the fact that each piece is unique with no two pieces the same. Due to the fact that this flooring

More information

MEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL

MEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL REVISED 1/24/2017 MEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL PLEASE READ ALL INSTRUCTIONS CAREFULLY, BEFORE YOU BEGIN INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY. Thank you

More information

Covelo Canyon INSTALLATION INSTRUCTIONS

Covelo Canyon INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Covelo Canyon Prior to installation, installer should check material for appropriate grade, color, graining and finish quality. Installer should STOP THE JOB if any defects that

More information

Engineered Flooring Installation Instructions For Unfinished Flooring

Engineered Flooring Installation Instructions For Unfinished Flooring READ ALL OF THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. IN ADDITION TO THESE INSTRUCTIONS, WE RECOMMEND THAT THE INSTALLER FOLLOW ALL INSTALLATION GUIDELINES SET FORTH BY THE NATIONAL

More information

Verify colour and finish before installation. Once the floor is installed, it is deemed to have been inspected, approved and accepted.

Verify colour and finish before installation. Once the floor is installed, it is deemed to have been inspected, approved and accepted. CLICK LAMINATE FLOORING INSTALLATION GUIDELINES Before you start read these Installer/Owner Responsibilities: Relative Humidity (RH) requirements: Laminate floors require a Relative Humidity of 35% - 50%

More information

ENGINEERED HARDWOOD FLOORS Glue, Staple Or Nail Down Installation

ENGINEERED HARDWOOD FLOORS Glue, Staple Or Nail Down Installation ENGINEERED HARDWOOD FLOORS Glue, Staple Or Nail Down Installation Columbia Engineered Hardwood Floors can be installed over most subfloors, and are engineered to be dimensionally stable, making them suitable

More information

WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions

WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION Responsibility for the suitability of this flooring

More information

Tesoro Woods Super-Strand Bamboo by MOSO Flooring Installation Instructions

Tesoro Woods Super-Strand Bamboo by MOSO Flooring Installation Instructions Tesoro Woods Super-Strand Bamboo by MOSO Flooring Installation Instructions Please read thoroughly before beginning installation. These installation instructions are specifically intended for use with

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! INSTALLATION INSTRUCTIONS FOR TONGUE & GROOVE HARDWOOD FLOORING Enclosed you will find installation instructions for the following products: Solid and Engineered Tongue & Groove (T&G) Hardwood ATTENTION!

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! INSTALLATION INSTRUCTIONS FOR TONGUE & GROOVE HARDWOOD FLOORING Enclosed you will find installation instructions for the following products: Solid and Engineered Tongue & Groove (T&G) Hardwood ATTENTION!

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR MIKASA TM REAL WOOD FLOORS These instructions are for all MIKASA TM real wood flooring products made using - - a unique and proven glue - less mechanism

More information

LOOSE LAY INSTALLATION GUIDE PAGE 1 of 6

LOOSE LAY INSTALLATION GUIDE PAGE 1 of 6 INSTALLATION GUIDE PAGE 1 of 6 MATERIALS REQUIRED FOR INSTALLATION: Tape Measurer Square Ruler Utility Knife 100lb Roller (if using adhesive) ACCEPTABLE SUBFLOORS: Happy Feet International will not warrant

More information

HAND-SCRAPED FLOORING INSTALLATION INSTRUCTIONS

HAND-SCRAPED FLOORING INSTALLATION INSTRUCTIONS HAND-SCRAPED FLOORING INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. IN ADDITION TO THESE INSTRUCTIONS, WE RECOMMEND THAT THE INSTALLER FOLLOW ALL INSTALLATION

More information

Royal River Hardwoods Installation

Royal River Hardwoods Installation Page 1 of 7 Installation Instructions INSTRUCCIONES DE COLOCACION - ESPAÑOL IMPORTANT Please read the following information and instructions in their entirety before proceeding with installation. Subfloors

More information

Lock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered

Lock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered Lock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered Please read the following instructions before starting the installation Applications... 1 Pre installation...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Page 1 of 7 Installation Instructions INSTRUCCIONES DE COLOCACION - ESPAÑOL INSTALLATION INSTRUCTIONS IMPORTANT Please read the following information and instructions in their entirety before proceeding

More information

SECTION WOOD GYMNASIUM FLOORING

SECTION WOOD GYMNASIUM FLOORING HORNER SAFE 2 SYSTEM Page 1 of 3 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general, of wood

More information

5G Click Floating Floor Installation Instructions

5G Click Floating Floor Installation Instructions 5G Click Floating Floor Installation Instructions Market Place RPF Can be installed right out of the carton with no acclimation. SUBFLOOR REQUIREMENTS While Market Place RPF is water resistant, it is not

More information

SECTION WOOD GYMNASIUM FLOORING

SECTION WOOD GYMNASIUM FLOORING HORNER MULTISPORT ULTRA SYSTEM Page 1 of 1 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general,

More information

A. This section includes pre-finished Higuera Hardwoods bamboo flooring and accessories for floors and stairs.

A. This section includes pre-finished Higuera Hardwoods bamboo flooring and accessories for floors and stairs. SECTION PART 1 - GENERAL 1.1 SUMMARY A. This section includes pre-finished Higuera Hardwoods bamboo flooring and accessories for floors and stairs. 1.2 RELATED DOCUMENTS A. Related Sections include the

More information

https://na1.salesforce.com/articles/installation/installation-instructions-3...

https://na1.salesforce.com/articles/installation/installation-instructions-3... 1 of 12 3/2/2015 2:58 PM Product Information Product Information Recommended Cleaner: Bruce Hardwood & Laminate Floor Cleaner Recommended Cleaner: Armstrong Hardwood & Laminate Floor Cleaner Robbins -

More information

SHAW SOLID HARDWOOD Installation Instructions Guidelines

SHAW SOLID HARDWOOD Installation Instructions Guidelines PRE-FINISHED, 3/4 & 5/16 SOLIDS, STRIP OR PLANK THE FOLLOWING INSTALLATION INSTRUCTIONS GUIDELINES ARE AN APPENDIX OF THE SHAW HARDWOODS WARRANTY FOR APPLICABLE PRODUCTS. PLEASE READ AND REVIEW THE ENTIRE

More information

Thomas Benjamin Architectural Flooring Hardwood Flooring Installation Instructions

Thomas Benjamin Architectural Flooring Hardwood Flooring Installation Instructions Aug 2016 Rev A Thomas Benjamin Architectural Flooring Hardwood Flooring Installation Instructions Applicable to floors purchased after 8-1-2016 TABLE OF CONTENTS IMPORTANT INFORMATION BEFORE YOU BEGIN

More information

Hill Country Innovations Installation Guide for Engineered Hardwood

Hill Country Innovations Installation Guide for Engineered Hardwood Prior to installation, installer should check material for appropriate grade, color, grain character and finish quality. Installer should STOP THE JOB if any defects that are detected or revealed through

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR This flooring replicates the look of a natural product which has natural variations in color and texture. For best visual

More information

Installation Instructions

Installation Instructions Click-Lock Glueless Floating Floor Installation Instructions ATTENTION! READ BEFORE INSTALLING! COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual

More information

HDWPC Flooring Installation Guidelines

HDWPC Flooring Installation Guidelines HDWPC Flooring Installation Guidelines 02.22.17 The purpose of this manual is to provide general installations recommendations based on certain installation environments. If there are other questions about

More information

ATTENTION! READ BEFORE INSTALLING!

ATTENTION! READ BEFORE INSTALLING! INSTALLATION INSTRUCTIONS FOR TONGUE & GROOVE HARDWOOD FLOORING Enclosed you will find installation instructions for the following products: San Pietro Solid Oak & Maple Collection Estate Solid Birch &

More information

Wellmade. - Installation Guide. General Information. Pre-Installation

Wellmade. - Installation Guide. General Information. Pre-Installation - Installation Guide Wellmade Wellmade WREW is a real wood veneer on a High Density Plastic Composite (HDPC ) flooring with patent pending technology. WREW is a Water Resistant Engineered Wood plank flooring

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS About PROTECH Luxury Vinyl Planks 8.7mm WPC Click Lock Contemporary Collection features patented interlocking planks for easy installation and is installed as a glue less floating floor. The interlocking

More information

VESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE

VESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE VESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE Vesdura Engineered Vinyl Plank features the patented Unilin interlocking planks for easy installation and is installed as a glueless floating floor. The

More information

ENGINEERED AND SOLID FLOORING INSTALLATION GUIDE

ENGINEERED AND SOLID FLOORING INSTALLATION GUIDE ENGINEERED AND SOLID FLOORING INSTALLATION GUIDE Table of Contents Section 1 Important Information Before You Begin... 1 Installer/Owner Responsibility... 2 Jobsite Conditions and Acclimation All Installations...

More information

Installation Instructions

Installation Instructions Installation Instructions Responsibilities of Installer / Owner: IMPORTANT: Solid Flooring Installation Instructions Please read these instructions before installation: To ensure full benefits of warranties,

More information

Yanchi Flooring Installation Guide HDF Engineered Color-blended Strand Woven Bamboo Flooring

Yanchi Flooring Installation Guide HDF Engineered Color-blended Strand Woven Bamboo Flooring Yanchi Flooring Installation Guide HDF Engineered Color-blended Strand Woven Bamboo Flooring PLEASE READ BEFORE INSTALLING INSTALLATION PLEASE READ THOROUGHLY BEFORE BEGINNING INSTALLATION. THESE INSTALLATION

More information

Mohawk SolidTech. SolidTech Installation Guidelines. Preparation

Mohawk SolidTech. SolidTech Installation Guidelines. Preparation 55 85ºF (13 30ºC) Preparation We recommend placing a single order for all cartons required for a commercial flooring project. 1. Always store and transport SolidTech Luxury Vinyl Flooring on a flat surface

More information

IMPEC BAMBOO INSTALLTION MANUAL

IMPEC BAMBOO INSTALLTION MANUAL IMPEC BAMBOO INSTALLTION MANUAL Please Read The Following Instruction Carefully Before Begin To Install Your Floor Thank You For Purchasing IMPEC BAMBOO General Info: The following guidelines and instructions

More information

MFMA Guide Specification for Sleeper and Sleeper with Plywood Floor Systems

MFMA Guide Specification for Sleeper and Sleeper with Plywood Floor Systems Sleeper and Sleeper with Plywood Floor Systems Purpose This Guide Specification is designed to assist in the production of actual architectural specifications for maple athletic flooring installations.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS LAMINATE 12.3MM EUROPEAN OAK COLLECTION Please inspect all flooring prior to installation. Carefully confirm that the color, finish, styling and quality fully meet the owner s expectations. If you determine

More information