SECTION ORNAMENTAL HANDRAILS AND RAILINGS
|
|
- Posy Lester
- 6 years ago
- Views:
Transcription
1 SECTION PART 1 - GENERAL ORNAMENTAL HANDRAILS AND RAILINGS 1.1 SUMMARY A. Section Includes: 1. Ornamental Handrails and Railings. 2. Glazed Panel Railings. 1.2 DEFINITIONS A. Guardrail: System of building components located near open sides of elevated walking surfaces for purpose of minimizing possibility of accidental fall from walking surface to lower level. B. Handrail: Horizontal or sloping rail grasped by hand for guidance or support, and for purpose of minimizing possibility of accidental falls on adjacent walking surface. 1.3 SYSTEM REQUIREMENTS A. Design Requirements: Drawings are diagrammatic and are intended to establish basic dimension of units, sight lines, and profiles of units. 1. Fabricator: Responsible for designing system, including anchorage to structural system and necessary modifications to meet specified requirements and maintain visual design concepts. 2. Employ registered professional engineer, licensed to practice structural engineering in jurisdiction where Project is located, to engineer each component of handrail and railing systems. 3. Provide concealed fastening wherever possible. 4. Extend railings 12 inches beyond top riser and 12 inches beyond plus one tread beyond bottom riser where not continuous. 5. Make clear distance between components of guardrail infill such that 4 inch diameter sphere cannot pass through opening. B. Structural Requirements: 1. Handrails: capable of withstanding following loads applied as indicated. 2. Uniform load of 50 PLF applied in any direction. 3. Concentrated and uniform loads above need not be applies simultaneously. C. Guardrail System: Capable of withstanding following loads applied as directed. 1. Concentrated load of 200 pounds applied at any point and in any direction at top of guardrail system. 2. Uniform load of 50 PLF applied horizontally perpendicular to plane of guardrail and vertically, simultaneously, at top of guardrail system to transmit load to supports. 3. Concentrated and uniform loads above need not be applies simultaneously. D. Infill Area of Guardrail System: Intermediate rails, baluster, pickets and panel fillers shall withstand horizontal load of 50 pounds on area not to exceed 1 square foot at any point. Above load need not be assumed to be acting concurrently with horizontal loads on railing system. E. Interface with Adjacent Systems: Integrate design and connections with adjacent construction. Accommodate allowable tolerances and deflections for structural members in installation. 1.4 SUBMITTALS A. General: Submit in accordance with Section B. Product Data: Submit for grout, glass, primer, and finishes. 1. Color Charts: Items requiring color selection. C. Shop Drawings: Indicate locations and complete fabrication details, materials, finishes, and installation details. BOKA Powell Project No February 2007
2 1. Stamp with seal and signature of professional engineer responsible for design. D. Changed Condition Drawings: Submit in accordance with Section E. Samples: Submit each type of metal finish and color and glass, where normal color and texture variations are to be expected, include two or more samples, showing limits of variation. F. Calculations: Submit for handrails and railings. 1. Calculations: Prepared by and bear seal and signature of registered Professional Engineer. G. Informational Submittals: Submit following packaged separately from other submittals: 1. Support Reactions Design Data: Submit in accordance with Section Certifications specified in Quality Assurance article. 3. Manufacturer's instructions. 1.5 QUALITY ASSURANCE A. Engineer Qualifications: Registered professional engineer licensed to practice structural engineering in jurisdiction where Project is located, with minimum of five years [documented] experience in design of handrail and railing systems. B. Fabricator Qualifications: Company specializing in fabricating work specified in this Section with minimum five years experience. C. Welder Qualifications: AWS certified within past 12 months for each type of weld required. Maintain current certification for duration of Project. D. Regulatory Requirements: Conform to ADA Accessibility Guidelines for Buildings and Facilities (ADAAG) or local code if more stringent requirements are applicable for installing work for accessibility to handicapped. E. Regulatory Requirements: Conform to requirements of local building codes and authorities having jurisdiction over Project. F. Certifications: 1. Certificates verifying AWS qualifications for each welder employed on Project. 2. Fabricator's certification that products furnished for Project meet or exceed specified requirements. 3. Engineering certifications. 1.6 FIELD SAMPLES A. General: Comply with Section Construct field sample 10 feet long by 42 inches wide as indicated. 2. Locate where directed. 3. Accepted sample may remain as part of Work. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Pre-Engineered Glazed Panel Railings: 1. Exterior Aluminum and Glass Railings: [ ]. 2. Accepted Substitute in accordance with Section MATERIALS A. Aluminum: 1. Extruded Bar and Shape: ASTM B221, 6063-T6 2. Extruded Pipe and Tube: ASTM B429, 6063-T6 3. Sheet: ASTM B209, 3003 or Castings: B26/B26M Alloy Handrail Connectors: Julius Blum and Co., Inc., Carlstadt, NJ. 6. B. Glass: Type: Tempered Safety Glass a. 1. Standard: ASTM C1048, Kind FT, Condition A, Type I. 2. Color: Clear-Class 1. BOKA Powell Project No February 2007
3 3. Thickness: ½ inch minimum. B. Bituminous Paint: Cold-applied asphalt mastic, comply with SSPC Paint 12, for aluminum railings. C. E. Non-Shrink Grout: Premixed, factory packaged, non-ferrous aggregate, non-staining, shrinkage-resistant, non-corrosive, non-gaseous, ASTM C Minimum Strength at 28 Days: 5000 PSI. 2. Acceptable Products: a. Masterflow 713, Master Builders, Cleveland, OH. b. Euco N.S., Euclid Chemical Co., Cleveland, OH. c. Crystex, L&M Construction Chemicals, Omaha, NE. d. SikaGrout 212, Sika Corporation, Lyndhurst, NJ. e. Sonogrout 10K, Sonneborn Building Products, Minneapolis, MN. f. Five Star Grout by US Grout Corp, Fairfield, CT. g. Accepted Substitute in accordance with Section D. Fasteners: Provide zinc-coated for exterior use 1. Bolts and Nuts: Regular hexagon head type, ASTM A307, Grade A. 2. Lag Bolts: Square head type, FS FF-B Machine Screws: Cadmium plated steel, FS FF-S Wood Screws: Flat head carbon steel, FS FF Plain Washers: Round, carbon steel, FS FF-W Masonry Anchorage Devices: Expansion shields, FS FF-S Toggle Bolts: Tumble-Wing Type FS FF-B-588, type class and style required. 8. Lock Washers: Helical spring type, carbon steel, FS FF-W ORNAMENTAL HANDRAILS AND RAILINGS FABRICATION A. General: Verify dimensions on site prior to fabrication. 1. Comply with ADAAG requirements. Maximum handrail size: [1-1/2 inches OD. 2. Fabricate to support design loads specified. 3. Fit and shop assemble in largest practical sizes. 4. Fabricate materials straight and true, without scratches, grind marks, scars, creases, buckles, ripples, or chatter marks, free from surface blemishes. 5. Fabricate panels to appear visually flat. B. Connections: 1. Pre-Engineered Glazed Panel Railings: Provide inside profile sleeves at railing, butt joints; exposed fasteners are not permitted. C. Brackets, Flanges, Fittings, and Anchors: Provide manufacturer's standard wall brackets, flanges, miscellaneous fittings and anchors for interconnection of handrail and railing members to other work. 1. For railing posts set in concrete, provide blocked out opening, not less than 6 inches deep and with inside dimensions not less than 1/2 inch greater than outside dimension of post. 2. Railing Brackets: Comply with ADA requirements. D. Joints: Mill to tight, hairline fit: Form joints exposed to weather to exclude water penetration. E. Ends: Capped. F. Inserts: Embedded in concrete or masonry work. Provide galvanized or cadmium-coated inserts for exterior work. G. Anchors: Provide toothed steel or lead-shield expansion bolt devices for drilled-in-place anchors. H. H. Glass Panels: Provide proper clearance and bite on glass. I. I. Clear distance between intermediate rails or balusters shall be such that sphere with diameter of 4 inches cannot pass through any opening. J. J. Removable Railing Socket: Cast into concrete to receive removable railing posts. Socket: Galvanized malleable iron: No. 66 ground socket by R & B Wagner, Inc., Milwaukee, WI. BOKA Powell Project No February 2007
4 K. K. Bends: Form by prefabricated elbow fittings and radius bends, except where configuration requires bending of railing members. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine conditions and proceed with Work in accordance with Section Coordinate setting drawings, templates, and instructions for installation of concrete, inserts, and anchor bolts embedded in concrete or masonry. 3.2 ORNAMENTAL HANDRAILS AND RAILINGS INSTALLATION A. A. Fit exposed connections to form tight, hairline joints. 1. Set work accurately in location, set posts and align to within 1/4 inch in 12 feet. Set rails horizontally or parallel to rake of steps or ramp to within 1/4 inch in 12 feet. 2. Do not weld, cut or abrade railings which have been finished after fabrication and are to be field connected by mechanical means. 3. Do not place masking tape or other similar materials to faces of glass or metal. B. Coat concealed surfaces of aluminum, which will be in contact with grout, concrete, masonry, wood, or dissimilar metals, with heavy coat of bituminous paint. C. C. Posts: Anchor posts by grouting into concrete. 1. Locate posts not less than 6 inches from control and expansion joints and from openings in concrete. 2. Non-Shrink Grout: Fill annular space solid with grout between posts and edges of openings to receive post. a. Leave anchorage joint exposed; wipe off excess grout and leave 1/8 inch build-up; slope away from post. 3. Anchor posts to metal base plates by a continuous weld. D. D. Anchoring Railing Ends: 1. Anchor railing ends into concrete or masonry with manufacturer's standard fittings. 2. Anchor railing ends to metal surfaces with manufacturer's standard fittings using concealed fasteners. E. E. Ornamental Handrails: Secure to walls with manufacturer's standard wall brackets. Cap ends. 1. Concrete or Solid Masonry: Use drilled-in expansion shields and concealed hanger bolts. 2. Hollow Masonry: Use toggle bolts with square heads. 3. Metal Stud Partitions: Attach to metal grounds with toggle bolts, or to wood blocking with lag bolts. F. F. Infill: 1. Glass Panels: Typically, position glass infill in relation to adjacent surfaces to prevent passage of sphere with outside diameter of not more than 4 inches unless more stringent requirement by Code. G. Installation of Glass Panels: 1. Glazed Panel Railings: Install to comply with railing manufacturer's instructions, beginning with erection of posts and other metal railing components, followed by setting of factory-cut glass panels H. Expansion Joints: At exterior applications, provide slip joint with internal sleeve extending 2 inches beyond joint on each side. 1. Fasten sleeve to one side only. 2. Locate expansion joints within 6 inches of post. 3. Provide at intervals of maximum 20 feet on center. 3.3 ADJUSTING, CLEANING AND PROTECTION BOKA Powell Project No February 2007
5 A. Protection: Comply with Section Protect finishes of railings and handrails from damage during construction by use of temporary protective coverings approved by railing manufacturer. Remove protective covering at project completion. Restore finishes damaged during installation and construction period. B. Protect finished installation under provisions of Section END OF SECTION BOKA Powell Project No February 2007
SECTION PART 1 - GENERAL
SECTION 05520 HANDRAILS AND RAILINGS (STEEL) PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Handrails: Round steel. 2. Guardrail System: Round steel. B. Related Sections: 1. Section 05120 - Structural
More informationNorthpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDECORATIVE METAL RAILINGS
SECTION 057300 - DECORATIVE METAL RAILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Steel and iron decorative railings. 1.2 PERFORMANCE REQUIREMENTS A. Delegated Design: Design railings, including
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationSECTION METAL STAIRS
SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B
SECTION 05 5213 - PIPE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationPIPE AND TUBE RAILINGS. Evansville Christian High School RELATED DOCUMENTS 1.1
SECTION 055213 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationSECTION 2 DIVISION 05 METALS
SECTION 2 DIVISION 05 METALS DIVISION 5 - METALS Note: This is a guide for Designers only. Contents shall not be used in lieu of specifications as part of the Designer s Contract Documents. GENERAL DESIGN:
More informationA. This Section includes the following: 1. Aluminum pipe and tube handrails and railings.
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationStudent Services & Classroom Addition
SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPIPE AND TUBE RAILINGS
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION ALUMINUM RAILINGS
SECTION 05522 ALUMINUM RAILINGS PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Aluminum pipe and tube railings. B. Related Sections include the following: 1. Division 5 Section "Ornamental
More informationSECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Welded stainless steel railing systems. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete; coordination with substrate.
More informationSECTION METAL STAIRS
SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. Stairs with concrete treads. B. Stairs with metal treads. C. Structural steel stair framing and supports. D. Handrails and guards. 1.02
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTrex Commercial Products page Metal Railing
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post Rail (Glass). D. Tensiline Railings (Cable). E. Track Rail (Glass).
More informationSECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post
More informationSECTION PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY 1.3 PERFORMANCE REQUIREMENTS
SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American Architectural Manufacturers
More informationAluminum Component Pipe Railings
1 SECTION 05 7360 ALUMINUM COMPONENT PIPE RAILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum component pipe handrails and railings. 1.02 RELATED REQUIREMENTS A. Section 02 9000: Landscaping: Installation
More informationStudent Services & Classroom Addition
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMASTERSPEC - SHORT FORM. B. See Division 5 Section "Metal Stairs" for steel tube railings associated with metal stairs.
SECTION 05721 - ORNAMENTAL RAILINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Glass supported railings. B. See Division 5 Section "Metal Stairs" for steel tube railings associated
More informationPIPE AND TUBE RAILINGS
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.01 DESCRIPTION A. Work of this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary
More informationSECTION ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH GLASS INFILLS
1 SECTION 05 7310 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH GLASS INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationPreassembled steel stairs with concrete-filled treads.
SECTION 055113 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec PART 1 - GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American
More informationSECTION METAL FLOOR PLATE STAIRS
SECTION 05513 - METAL FLOOR PLATE STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS
Page 1 of 17 SECTION 11 4600 FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationSECTION PRE-ENGINEERED ALUMINUM STAIRS AND RAILINGS
SECTION 05 51 20 - PRE-ENGINEERED ALUMINUM STAIRS AND RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION PIPE AND TUBE RAILINGS
SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Invisirail
More informationSECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Handrails and guardrails. 1.2 PERFORMANCE REQUIREMENTS A. General: In engineering railings to withstand structural loads indicated, determine
More information1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMETAL HANDRAILS AND RAILINGS. A. Properly identified manufacturer's literature, including shop and erection drawings before starting work.
SECTION 05520 METAL HANDRAILS AND RAILINGS PART 1 GENERAL 1.01 SUBMITTALS A. Properly identified manufacturer's literature, including shop and erection drawings before starting work. B. Railing Assemblies
More informationKeuka Studios May 2008 SECTION {05720} CABLE RAILING SYSTEM {CABLE RAILING SYSTEM} Display hidden text for Specifier Notes.
SECTION 05 73 16 {05720} CABLE RAILING SYSTEM {CABLE RAILING SYSTEM} Display hidden text for Specifier Notes. PART 1 GENERAL 1.1 SUMMARY A. Section includes cable railing system, with architectural metal
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 05511 - METAL STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSECTION METAL STAIRS
Tender SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. This section includes internal and external shop fabricated pre assembled steel stairs with integral handrails and ballustrades
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPART 1 GENERAL METAL RAILINGS
SECTION 05 52 00 (05520) PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Interior Railings a. Steel Pipe Railings. 1.2 REFERENCES A. ASTM International Publications: 1. A36 "Standard Specification for
More informationSECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Summit tm Modular Railing System
SECTION 05720 ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Summit tm Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install supported glass stainless steel railings, glass
More information.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC
05 12 00 STRUCTURAL STEEL FRAMING Page 1 of 3 1 General 1.1 SECTION INCLUDES.1 Structural steel framing and support members 1.2 RELATED SECTIONS.1 Section 05 50 00 Metal Fabrications 1.3 REFERENCES.1 American
More informationSECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Monaco tm Modular Railing System
SECTION 05720 ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Monaco tm Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install supported glass stainless steel railings, glass
More informationa. Uniform load of 50 lbf/ ft. applied horizontally and concurrently with 100 lbf/ ft. applied vertically downward.
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSuperior Aluminum Guide Specification 10/4/2016 Non-Welded Aluminum Pipe Railing
The following specification has been developed by: Superior Aluminum Products 555 East Main Street Russia, Ohio 45363-0430 to assist Architects and Designers in the specification of Non Welded Concealed
More informationSECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Glenlake Modular Railing System
SECTION 05 5200 ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Glenlake Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install post supported stainless steel railings and components.
More informationB. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work.
SECTION 055116 - METAL FLOOR PLATE STAIRS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ORNAMENTAL ALUMINUM RAILING
SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Decorative Wire Rope Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in
More informationSECTION ORNAMENTAL ALUMINUM RAILING
SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Pipe Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in concrete.
More informationSECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Casino Modular Railing System
SECTION 05 5200 ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Casino Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install stainless steel railings and components. 1.02 REFERENCE
More informationA. American Society for Testing and Materials (ASTM):
SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 03420 - Precast, Prestress Concrete Sections. 3. 04420 - Concrete Unit Masonry. 4.
More informationTrex Commercial Products page Decorative Metal Railing
SECTION 05 73 00 DECORATIVE METAL RAILINGS TREX COMMERCIAL PRODUCTS Monaco Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install supported glass stainless steel railings, glass
More informationSTRUCTURAL STEEL FRAMING
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 SUMMARY A. Section includes 1. Structural steel framing 2. Structural steel framing required for support and framing of rooftop mechanical
More informationSECTION (10705) EXTERIOR SUN CONTROL DEVICES
10 71 13 SECTION (10705) EXTERIOR SUN CONTROL DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationB. Shop Drawings: Include plans, elevations, sections, details, and attachments.
SECTION 055119 - METAL GRATING STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationGUIDE SPECIFICATION (formerly 05521) - CONNECTORAIL
SECTION 05521--CONNECTORAIL NON-WELDED PIPE GUIDE SPECIFICATIONS: These guide specifications are intended to be used as the basis for developing job specifications and must be edited to fit specific job
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationSECTION METAL FABRICATIONS
SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 03420 - Precast, Prestress Concrete Sections. 3. 04420 - Concrete Unit Masonry. 4.
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 05 5117 ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationA. Atlantic Railing Series with Mushroom Top and Square Pickets
100 Series-A1-A10 PART 1 General 1.1 SECTION INCLUDES A. Atlantic Railing Series with Mushroom Top and Square Pickets 1.2 RELATED SECTIONS A. Section 05510-Metal Stairs: Metal Handrails other than those
More informationSECTION GLASS BALUSTRADE RAILING SYSTEMS
SECTION 05 73 13 GLASS BALUSTRADE RAILING SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Division 01 - General Requirements,
More informationSECTION ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck)
SECTION 13125 ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck) PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationAmerican Metal Specialties, Inc.
American Metal Specialties, Inc. www.cablerailings.com (253) 272-9344 (253) 627-3843 Fax PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 05 73 00 STAINLESS STEEL ORNAMENTAL HANDRAILS AND RAILINGS For best
More informationSECTION FABRICATED ENGINEERED STRUCTURES. A. Pre-engineered, shop-fabricated structural steel building with formed purlin framing.
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 13 34 00 FABRICATED ENGINEERED STRUCTURES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION STRUCTURE MOUNT RAILING SYSTEM
SECTION 05520 STRUCTURE MOUNT RAILING SYSTEM Peak Fall Protection specializes in the design, engineering, fabrication, installation, and certification of fall protection safety systems. Our team of safety
More informationSECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM
Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING
More informationSECTION HANDRAILS AND RAILINGS. A. Section Metal Fabrications: Associated metal supports.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Handrails and guardrails B. Guardrails for hatches and openings. C. Safety barriers. D. Roof edge protection. 1.2 RELATED SECTIONS
More informationSPECIFICATIONS: Architectural Aluminum Railings
PART ONE: GENERAL 1.1 SUMMARY SPECIFICATIONS: Architectural Aluminum Railings A. Work in this section includes custom and standard Interior and Exterior aluminum railings and guardrails. 1.2 PERFORMANCE
More information4621 East 75 th Terr. Kansas City, MO Phone (816) l Fax (816) LiversBronze.com l
4621 East 75 th Terr. Kansas City, MO 64132 Phone (816) 300 2828 l Fax (816) 300 0864 LiversBronze.com l Livers@LiversBronze.com SECTION 05 73 13 [ILLUME LED LIGHTED RAILING] [LIVERS BRONZE RAILING SYSTEM]
More informationSECTION DECORATIVE METAL AND GLASS RAILING
SECTION 05 73 00 DECORATIVE METAL AND GLASS RAILING PART 1 GENERAL 1.1 SUMMARY A) This section includes both standard and custom handrails as shown in the contract drawings. B) These include aluminum,
More informationSECTION STRUCTURAL STEEL
SECTION 05120 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this
More information1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.
PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationA. Glass Railing Series with Mushroom Top Cap with Glass Panel Infill.
100 Series Bayview ( Two-Line) Glass Rail-A1 Top Cap PART 1 General 1.1 SECTION INCLUDES A. Glass Railing Series with Mushroom Top Cap with Glass Panel Infill. 1.2 RELATED SECTIONS A. Section 03300 Cast-
More informationSPECIFICATION FOR PERMANENT BEAM GRANDSTAND WITH INTERLOCK WELDED DECK SYSTEM
E & D SPECIALTY STANDS, INC. MANUFACTURERS OF QUALITY STANDS AND SEATING 2081 FRANKLIN STREET - P.O. BOX 700 - NORTH COLLINS, NEW YORK 14111 716-337-0161-1-800-525-8515 FAX 716-337-2903 - SALES FAX 716-337-3436
More informationMETALS Commissioning of Metals Structural Steel Framing Steel Studs... 2
~ 05-1 ~ 05 00 00 Metals 05 00 00 METALS... 2 05 08 00 Commissioning of Metals... 2 05 12 00 Structural Steel Framing... 2 05 12 30 Steel Studs... 2 05 45 00 METAL SUPPORT ASSEMBLIES... 2 05 50 00 METAL
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More informationSECTION METAL PLATE CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 06192 - PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationSECTION COLD-FORMED METAL TRUSSES
SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationNorth Hanover Township School District North Hanover Township, New Jersey
SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION STRUCTURAL STEEL
SECTION 051200 STRUCTURAL STEEL PART 1 GENERAL 1.01 SECTION INCLUDES A. Structural steel framing members and support members. B. Base plates, shear stud connectors. C. Grouting under base plates. 1.02
More informationCommission No Section
Commission No. 1511 Section 05120-1 PART ONE - GENERAL 1.1 DESCRIPTION A. Work Included: Structural steel and grout. Furnish, fabricate, mark for erection identification, pack, crate, or otherwise properly
More information# DAYTONA BEACH PIER BUILDING RESTORATION 06/10
SECTION 055000 - METAL FABRICATIONS PART 1 - PRODUCTS 1.1 METALS A. Ferrous Metals: 1. Steel Plates, Shapes, and Bars: ASTM A 36/A 36M. 2. Stainless-Steel Bars and Shapes: ASTM A 276, Type 304. 3. Rolled-Steel
More informationSECTION ORNAMENTAL WELDED STEEL FENCING
SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Fusion welded and rackable ornamental steel picket fence system. B. Related sections: 1. Section 03310 Concrete Work for post support. 2. Section 09960
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions apply to this Section. 1.2
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More information1. Manufacturer's product lines of railings assembled from standard components.
SECTION 057300- DECORATIVE METAL RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementmy Conditions and Division 01 Specification
More informationNational Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 [ ].
National Master Specification (NMS) Section 05 50 00 METAL FABRICATIONS Publisher: Spex.ca Page 1 Approved: 2010-06-30 Part 1 General 1.1 RELATED REQUIREMENTS.1 [ ]. 1.2 REFERENCES.1 CSA International.1
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220529 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
Page 230548-1 SECTION 230548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationDIVISION 5 METALS COLD FORMED METAL FRAMING Structural Metal Stud Framing
05 40 00 COLD FORMED METAL FRAMING 05 41 00 Structural Metal Stud Framing 05 50 00 METAL FABRICATIONS 05 51 00 Metal Stairs 05 51 13 Metal Pan Stairs 05 52 00 Metal Railings 05 52 13 Pipe and Tube Railings
More informationSECTION ALUMINUM HANDRAILS AND RAILINGS
SECTION 05 52 00 ALUMINUM HANDRAILS AND RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Division 01 - General Requirements,
More informationSECTION DECORATIVE METAL RAILINGS
SECTION 05 73 00 DECORATIVE METAL RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Vertical Stainless Steel Cable Railing System. B. Horizontal Stainless Steel Cable Railing System. 1.2 RELATED SECTIONS
More informationHANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT SECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
13686.00 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT 230529-1 SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT 1.1 SUMMARY A. Section Includes: 1. Metal pipe hangers and supports.
More informationCode Compliance Research Report CCRR-0238
Code Compliance Research Report CCRR-0238 Issue Date: 11-09-2016 Revision Date: 11-29-2018 Renewal Date: 11-09-2019 DIVISION: 05 00 00 METALS Section: 05 52 00 Metal Railings CPG Building Products LLC
More informationSTRUCTURAL PRECAST CONCRETE RAMP, STEP, AND ELEVATED PLATFORM UNITS
Section 03412 Page 1 PART 1: General 1.1 Summary STRUCTURAL PRECAST CONCRETE RAMP, STEP, AND ELEVATED PLATFORM UNITS A. Provide pre-cast concrete ramp, step and elevated platform units for handicapped
More informationSECTION COILING COUNTER DOORS
SECTION 08 33 13 COILING COUNTER DOORS SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use overhead coiling counter shutters as closures
More informationSECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN
SECTION 08350 MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION VIBRATION CONTROLS FOR PLUMBING PIPING AND EQUIPMENT
Page 220548-1 SECTION 220548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION HANGERS AND SUPPORTS PART 1 - GENERAL. A. Drawings and Division 1 Specification Sections, apply to this Section.
1.01 RELATED DOCUMENTS SECTION 15060 HANGERS AND SUPPORTS PART 1 - GENERAL A. Drawings and Division 1 Specification Sections, apply to this Section. 1.02 SUMMARY A. This Section includes hangers and supports
More information