SECTION GYPSUM BOARD ASSEMBLIES
|
|
- Jared Banks
- 6 years ago
- Views:
Transcription
1 SECTION GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Metal stud wall and ceiling framing, 20 gauge. B. Metal channel suspended ceiling framing. C. Gypsum board. D. Gypsum sheathing. E. Taped and sanded joint treatment. F. Edge trim, reveals and moldings. G. Fire rated shaft wall systems with ratings as listed on the drawings. 1.2 RELATED SECTIONS A. Section Cold Formed Metal Framing. B. Section Board Insulation. 1.3 REFERENCES A. ANSI/ASTM C36 - Gypsum Wallboard. B. ANSI/ASTM C79 - Gypsum Sheathing Board. C. ASTM C423 Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method. D. ANSI/ASTM C475 - Joint Treatment Materials for Gypsum Wallboard Construction. E. ANSI/ASTM C630 - Water Resistant Gypsum Backing Board. F. ANSI/ASTM C645 - Non-Load (Axial) Bearing Steel Studs, Runners (Track), and Rigid Furring Channels for Screw Application of Gypsum Board. G. ASTM E795 Standard Practices for Mounting Test Specimens During Sound Absorption Tests. H. USG's Gypsum Construction Handbook. I. IBC, 2012 Edition. 1.4 SUBMITTALS Standard Specifications Page 1 of 6
2 A. Product Data: Include manufacturer's literature on metal framing, ceiling suspension systems, gypsum board, joint tape and compound. Include test data verifying acoustical performance. 1.5 REGULATORY REQUIREMENTS A. Conform to the requirements of IBC except where more restrictive requirements are specified in this section. PART 2 PRODUCTS 2.1 ACCEPTABLE MANUFACTURERS - GYPSUM BOARD SYSTEM A. United States Gypsum Co. B. Celotex. C. Georgia Pacific. D. Pabco. E. James Hardie Gypsum 2.2 FRAMING MATERIALS A. Studs and Tracks: ANSI/ASTM C645; galvanized, sizes and shapes shown on the drawings. Provide 20 gauge C studs unless noted otherwise. Framing shown as 18 gauge or heavier is specified under Section Cold Formed Metal Framing. B. Backing: Galvanized sheet metal, 20 gauge. C. Resilient Channels: 25 ga. hat shaped formed steel. D. Furring Channels: 20 ga., 7/8" hat shaped formed steel. E. Ceiling Channels: 16 ga., 1-1/2" cold rolled galvanized steel. F. Hanger Wire: 8 ga. galvanized steel. G. Ceiling Struts: Pre-manufactured struts, specifically designed for horizontal restraint of suspended ceiling systems, similar to USG'S Donn Compression Posts. H. Galvanized "Z" channels for board insulation attachment are specified in Section Board Insulation. I. Ceiling Edge Reveal: 20 gage sheet metal in size and configuration as shown on drawings. J. Shaft Wall Systems: Materials and methods in accordance with agency rating requirements. 2.3 GYPSUM BOARD MATERIALS A. Gypsum Board: ANSI/ASTM C36; fire resistive type X, UL rated; 5/8 inch, maximum permissible length; ends square cut, tapered edges. Standard Specifications Page 2 of 6
3 B. Moisture Resistant Gypsum Board: ANSI/ASTM C630; 5/8 inch, maximum permissible length; ends square cut, tapered edges. C. Gypsum Sheathing Board: ASTM C79, moisture resistant type, 1/2 inch thick, maximum permissible lengths, square cut ends and edges, water repellent paper faces. D. Gypsum Liner Panels: ANSI/ASTM C36, fire resistive type X, UL rated; 1 inch thick. E. Cement board: ½ inch thick. 2.4 ACCESSORIES A. Acoustical Sealant: Non-hardening, permanently resilient and non-skinning, for use in conjunction with gypsum board. B. Corner Beads: Metal. (No paper) C. Joint Materials: ANSI/ASTM C475; reinforcing tape, joint compound, adhesive, water, and fasteners. D. Control Joint: USG 093. E. Texture Material: Spray-applied, compatible with joint system. Provide "Orange Peel" texture unless noted otherwise. Texture to match existing finish. F. Fasteners: Type S self tapping screws in size and spacing as required by IBC or rating of gypsum board wall system. G. Duct Liner: Manufacturer's standard 2 inch thick black faced duct liner; 1.5 pcf to 3 pcf. Acoustical performance: Minimum NRC 0.95 (ASTM C423) when tested with Type A mount (ASTM E795). H. Outlet Acoustical Box Pad: Self adhesive polybutenebutyl pads by Harry A. Lowry & Associates, or equal. PART 3 EXECUTION 3.1 INSPECTION A. Verify that site conditions are ready to receive work. B. Coordinate with installer of ceramic tile for installation of backing board in lieu of gypsum board as specified in Section Ceramic Tile. C Beginning of installation means acceptance of substrate. 3.2 METAL STUD INSTALLATION A. Accurately layout partition and wall lines from the dimensions shown on the Drawings. B. Install metal studs and accessories in accordance with the manufacturer's recommendations and recommended industry practices included in USG's Gypsum Standard Specifications Page 3 of 6
4 Construction Handbook, anchoring all components firmly into position. Minimum 20 gauge 3 5/8 inch studs for wall construction. C. Align partition and wall assemblies to a tolerance of one in 200 horizontally and one in 500 vertically. D. Space studs as required for compliance with pertinent regulations and as noted on drawings. Space studs at 16" O.C. and 24 O.C. for C-H studs. E. Provide minimum three studs at all corners and provide double studs at all wall openings, door and window jambs. F. Provide sheet metal backing/blocking for support of all wall mounted equipment and fixtures including, but not limited to, plumbing fixtures, toilet partitions, wall cabinets, toilet accessories, hardware, handrails, grab bars, mirrors, marker and tack boards, draperies, base boards, monitors and other wall mounted items. G. Coordinate with other trades for proper size, spacing, thickness and attachment requirements of backing/blocking. Provide 20 gauge sheet metal unless otherwise shown on the drawings or required by a specific item. H. Coordinate requirements for pipes, ducts, conduits and other items required to be enclosed within the partition and wall system. I. Shaft wall systems shall be installed in strict accordance with the requirements of the rating agency. J. Provide double studs, back to back, for location of expansion joints in gypsum board. 3.3 CEILING INSTALLATION A. Install system capable of supporting imposed loads to a deflection of 1/360 maximum. B. Install after major above ceiling work is complete. Coordinate the location of hangers with other work. C. Hang suspension system independent of walls, columns, ducts, pipes and conduit. Where carrying members are spliced, avoid visible displacement of face plane of adjacent members. D. Where ducts or other equipment prevent the regular spacing of hangers, reinforce the nearest affected hangers and related carrying channels to span the extra distance. E. Space hanger wires as required by IBC for carrying channel spacing and within 6" of ends. F. Install carrying channels at 36" O.C. and within 6" of walls. Provide 1" clearance between channels and abutting walls. G. Lap channels 12" at splices. H. Install furring channels at right angles to carrying channels at 16" O.C. and within 6" of walls and maintain 1" clearance to walls. I. Secure channels and splices with 18 ga. tie wire. Standard Specifications Page 4 of 6
5 J. Reinforce openings in ceiling which interrupt carrying or furring channels with lateral channel bracing. K. Install perimeter edge reveal sheet metal per manufacturer s recommendations. L. Provide horizontal restraint consisting of: 1. Four No. 12 gauge wires secured to main runners within 2 inches of cross runner intersection and splayed 90 degrees from each other at an angle not exceeding 45 degrees from the plane of the ceiling. 2. Struts fastened to the main runner extending to and fastening to structure above. Place struts 12 feet on center in both directions with the first point within 6 feet from each wall. M. Shaft wall ceiling systems shall be installed in strict accordance with the requirements of the rating agency. N. Install to meet IBC Seismic Requirements and Clark County amended codes. O. When ceiling is open on edges or you can visually see above the ceiling, the area visable is to be painted black (blacked out). 3.4 ACOUSTICAL ACCESSORIES INSTALLATION A. Install resilient channels at maximum 24 inches on center. Locate joints over framing members. B. Install acoustical sealant within partitions in accordance with manufacturer's instructions. C. Install duct liner board with manufacturer's recommended adhesive and mechanical fasteners where appropriate. Boards to be placed tight to each other and to perimeter. Touch-up any damaged or abraded areas with flat black paint to provide a solid black surface. D. Outlet Acoustical Box Pads: Wrap around sides and back of electrical boxes. Leave no gaps. 3.5 GYPSUM BOARD INSTALLATION A. Install gypsum board in accordance with manufacturer's instructions, recommended industry practices included in USG's Gypsum Construction Handbook and in accordance with requirements of assembly rating where rated construction is called for. B. Erect single layer board in either horizontal or vertical direction, with ends and edges occurring over firm bearing except where treated joints occur at right angles to framing or furring. C. Use screws when fastening gypsum board to metal furring or framing. D. Double Layer Applications: Use gypsum backing board for first layer, placed perpendicular to framing or furring members. Place second layer perpendicular to first layer. Offset joints of second layer from joints of first layer. E. Double Layer Applications: Secure second layer to first in manufacturer's instructions. Standard Specifications Page 5 of 6
6 F. Treat cut edges and holes in moisture resistant gypsum board and exterior gypsum ceiling board with sealant. G. Place control joints consistent with lines of building spaces, and at a maximum of 30 feet center to center. Also place control joints where base wall construction contains building control or expansion joints. Where joint is in rated wall add additional layer of board to maintain fire rating. H. Place corner beads at external corners. Use longest practical length. Place edge trim gypsum board abuts dissimilar materials as indicated I. Erect exterior gypsum sheathing horizontally, with edges butted tight and ends occurring over firm bearing. J. Install reveals and trim in accordance with details on drawings. 3.6 JOINT TREATMENT A. Provide tape and joint compound finish at all exposed joints edges and corners to smooth surface ready to receive finishes. B. Apply tape pressed into joint compound or by mechanical tool designed for this process. C. Apply second coat of joint compound to extend beyond joint center approximately 3-1/2 inches. Apply to a smooth even plane. After drying or setting sand or smooth as needed to eliminate high spots or excessive compound. D. Apply third coat of joint compound except at concealed locations not subject to view. Third coat shall be applied to feather edges approximately 6 inches from center of joint. After drying, lightly sand to leave a smooth even surface. E. Provide spray-applied texture at all gypsum board exposed to view. Provide sample panel of texture for approval of Owner prior to start of texture application. 3.7 TOLERANCES A. Maximum Variation from True Flatness: 1/8 inch in 10 feet in any direction. END OF SECTION Standard Specifications Page 6 of 6
SECTION GYPSUM BOARD & SHEATHING SYSTEMS
PART 1!GENERAL! 1.01! SECTION INCLUDES SECTION 09260 GYPSUM BOARD & SHEATHING SYSTEMS! Metal stud wall framing. Metal channel ceiling framing.! Gypsum board.! Sheathing.! Taped and sanded joint treatment.!
More informationSECTION GYPSUM BOARD
SECTION 09250 GYPSUM BOARD PART 1GENERAL 1.1 SUMMARY A. Related Documents: General and Supplementary Conditions of the Contract, Division 1 - General Requirements, and Drawings are collectively applicable
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 09260 - A. Metal stud wall framing. Denoted on drawings as "metal studs". B. Metal channel ceiling framing. C. Acoustic insulation and sealant. D. Cementitious
More informationSECTION GYPSUM BOARD
SECTION 09260 - GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established in General and Supplementary Conditions of the Contract, Division 1 General Requirements, and the
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationEXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION GYPSUM BOARD PART 1 - GENERAL
SECTION 09250 - GYPSUM BOARD PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationSECTION GYPSUM BOARD ASSEMBLIES
1 PART ONE - GENERAL 1.1 COORDINATION SECTION 09260 GYPSUM BOARD ASSEMBLIES A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 - GENERAL 1.1 SUMMARY SECTION 09 21 16 A. Provide gypsum board assemblies as shown and specified. Work includes: 1. Walls, partitions, and soffits, including metal framing systems. 2. Acoustical
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 092216 - COLD FORMED STEEL FRAMING - NON-STRUCTURAL (CFSF-NS) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ACTION
More informationSECTION GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 09 2116 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance criteria for gypsum board assemblies. B. Acoustic insulation. C. Gypsum sheathing. D. Cementitious backing board. E. Gypsum wallboard.
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 6
DECEMBER, 2016 Page 1 of 6 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 07 21 16 - Batt and Blanket Insulation..3 Section 07 92 10 - Sealants..4 Section 09 91 00
More informationSECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board
SECTION 09260 GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard
More informationHome Depot Page 1 of 5 HDPB Humacao, PR 10/19/09
PART 1 - GENERAL 1.01 SUMMARY A. Types of cold-formed metal framing units include the following: 1. C-shaped steel studs B. Related work specified elsewhere includes but may not be limited to: 1. Section
More information1. Non-load-bearing steel framing systems for interior gypsum board assemblies. 2. Suspension systems for interior gypsum ceilings and soffits.
SECTION 09 2216 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Non-load-bearing steel framing systems for interior gypsum board assemblies. 2. Suspension systems for interior gypsum ceilings and
More informationDIVISION 5 METALS SECTION COLD-FORMED METAL FRAMING
DIVISION 5 METALS SECTION 05 40 00 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationSECTION NON-STRUCTURAL METAL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 22 16 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Gypsum board screw attached to wood framing and furring members, joint treatment, and accessories. 2. Installation of
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. SECTION GYPSUM BOARD ASSEMBLIES
SAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. Specifications, Quality Assurance, Inspections & Investigations for Your Construction Projects 2231 ROUTE 50 P.O. BOX 248 TUCKAHOE, NJ 08250 p: 609.628.2390
More informationSECTION COMPOSITE CORE ACOUSTICAL PANEL CEILINGS. Sound-Rite Inc. #9, rd Avenue NE Calgary, AB T2A 7P3
SECTION 09510 COMPOSITE CORE ACOUSTICAL PANEL CEILINGS Sound-Rite Inc. #9, 2821 3rd Avenue NE Calgary, AB T2A 7P3 Tel 403-296-0505 Fax 403-296-0511 Email info@sound-rite.com Web www.sound-rite.com Techstyle
More informationStudent Services & Classroom Addition
SECTION 095133 - ACOUSTICAL METAL PAN CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationStore No MAY 13 Addendum No. 1 SECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationCOOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No.
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationTechnical Services Information Bureau
Technical Services Information Bureau INSTALLING ACOUSTICAL LAY-IN TYPE CEILINGS IN SEISMIC REGIONS AUGUST 2009 UPDATED MAY 2017 TECHNICAL BULLETIN This document covers the installation practices recognized
More informationA. Product Data: For each type of product specified.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION NON--STRUCTURAL METAL FRAMING
The Collective Voice of America s Steel Framing Industry The Steel Framing Industry Association (SFIA) is dedicated to expanding the market for cold-formed steel in construction through programs and initiatives
More informationConstruction Standards PAGE
Construction Standards PAGE 092613-1 SECTION 092613 - PART 1 - GENERAL 1.1 M.S.U. ISSUES A. It is the intent of MSU that all gypsum veneer plaster used on its projects will comply with LEED NC 3 Credit
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 095113 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationConstruction Standards PAGE
Construction Standards PAGE 095113-1 SECTION 095113 - PART 1 - GENERAL 1.1 M.S.U. ISSUES 1. It the intent of MSU that all joint sealants used on its projects will comply with LEED NC 3 Credit Requirements
More informationBEARING METAL STUD FRAMING
L-1 Section 05410 Long Form Specification LOAD BEARING METAL STUD FRAMING This section includes axially loaded steel studs, with unique slotted top channels, usually of 0.91, 1.2 and 1.5 mm (16, 18, or
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Interior gypsum wallboard. 2. Tile backing panels. B. Related Sections: 1. Section 012300 Alternates. 1.2 SUBMITTALS A.
More informationSECTION GYPSUM BOARD
SECTION 09 2900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Includes But Not Limited To: 1. Furnish and install gypsum board as described in Contract Documents, except behind ceramic tile. 2. Furnish
More informationA. This Section includes acoustical panel ceilings installed with exposed suspension systems.
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO. 2700
SECTION 09 5113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION GYPSUM WALLBOARD. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 092116 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2116 - NON-LOAD-BEARING STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationONE SCHOOL STREET SEPTEMBER 18, 2008 GOWANDA, NEW YORK ARCH PROJECT NO
SECTION 09265 - GYPSUM BOARD SHAFT-WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationProduct Specification
General Specification Notes: SECTION 09210 / 09 21 00\ Finish Coat Plasters References in blue are general indicators to the specifier. References in red relate to fire-rated assemblies and/or code related
More informationA. Extent of each type of gypsum drywall construction required is indicated on the Drawings.
09250 GYPSUM WALLBOARD PART 1 - GENERAL 1.1 STIPULATIONS A. The specifications sections " General Conditions of the Construction Contract ", "Special Conditions", and "Division 1 - General Requirements"
More informationMETAL SUSPENSION SYSTEMS FOR LAY-IN PANEL CEILINGS: 2001 CBC IR
California Department of General Services. Division of the State Architect. Interpretation of Regulations Document METAL SUSPENSION SYSTEMS FOR LAY-IN PANEL CEILINGS: 2001 CBC IR 25-2.01 References: 2001
More informationSECTION NON-LOAD BEARING WALL FRAMING. B. Section Furring and Lathing: Lath and furring for interior plaster applications.
SECTION 09.22.16 NON-LOAD BEARING WALL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Non-load bearing metal studs for wall assemblies. B. Area Separation and shaft wall framing products. 1.2 RELATED SECTIONS
More informationSECTION LINEAR METAL CEILINGS
SECTION 09 5423 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More informationSECTION (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 09 21 16.23 (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Shaft Enclosures 2. Chase Enclosures 3. Stair Enclosures B. Related Sections: 1.02 DEFINITIONS
More informationUniSpec II - Store Planning
UniSpec II - Store Planning 072613 SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Suspended metal grid ceiling system. 2. Acoustical panels. 3. Perimeter
More informationDIVISION 5 - STRUCTURAL STEEL AND IRON WORK
DIVISION 5 - STRUCTURAL STEEL AND IRON WORK SECTION 05100 STRUCTURAL METAL FRAMING PART 1.00 GENERAL 1.01 SCOPE OF WORK A. Work Included: 1. 2. Structural steel complete in place. Steel joists complete
More informationShaftwall & Stairwell Systems Fire protection & sound isolation for shafts & stairwells
Shaftwall & Stairwell Systems Fire protection & sound isolation f shafts & stairwells what the job demands Shaftwall & Stairwell Systems Fire protection & sound isolation systems f elevat shafts, stairwells
More informationSECTION GYPSUM BOARD
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 29 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. AC: Articulation
More informationGYPSUM BOARD
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationGYPSUM BOARD SECTION GYPSUM BOARD PART 1 - GENERAL
13686.00 GYPSUM BOARD 092116-1 1.1 RELATED DOCUMENTS: SECTION 092116 - GYPSUM BOARD PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationCONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008
SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough
More informationSECTION COLD-FORMED METAL FRAMING
SECTION 05.40.00 COLD-FORMED METAL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Cold-formed metal framing for: B. Exterior load-bearing steel stud walls. 1. Interior load-bearing steel stud walls. 2.
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION COLD-FORMED METAL FRAMING
SECTION 05.40.00 COLD-FORMED METAL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Cold-formed metal framing for: B. Exterior load-bearing steel stud walls. 1. Interior load-bearing steel stud walls. 2.
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095423 - LINEAR METAL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2013 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2013 Application and Finishing of Gypsum Panel Products. Each
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2016 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2016 Application and Finishing of Gypsum Panel Products. Each
More informationSECTION ACOUSTICAL CEILINGS
PART 1- GENERAL 1.1 DESCRIPTION SECTION 09 51 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationA. Types of lightgauge metal framing units include the following: 1. C-shaped structural steel studs Uniform Building Code.
SECTION 05400 COLD-FORMED METAL FRAMING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationI-STUD Shaftwall System
I-STUD Shaftwall System Summit Tower I-Stud and CertainTeed Shaftliner TM MILL CERTIFIED Steel-Con 00% GALVANIZED Steel Construction Systems UL Evaluation Report No. ER3660-02 Intertek The I-Stud is approved
More informationInstruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
SOUND ISOLATION CLIPS Installation Manual Instruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationStudent Services & Classroom Addition
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationAND ACCESSORIES FOR DRYWALL CONSTRUCTION
STEEL TRIMS AND ACCESSORIES FOR DRYWALL CONSTRUCTION Quality in your corner. THE STRENGTH WITHIN MONTREAL TORONTO CALGARY EDMONTON VANCOUVER STEEL TRIMS AND ACCESSORIES for Construction BAILEY HAS YOUR
More informationRAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationInstallation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
Installation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86 inch Weight....025 lbs Max Spacing...48
More informationGA APPLICATION OF GYPSUM SHEATHING
1. Scope 1.1 This specification describes the minimum requirements for, and the methods of handling, storage, and application of, gypsum sheathing for use as a substrate for exterior claddings. 1.1.1 Exterior
More informationMETALWorkS. RH200 Custom Hook-on Panels. General Installation Instructions. Ceiling 1.0 GENERAL Site Conditions Product Description
Ceiling Systems Between us, ideas become reality METALWorkS General Installation Instructions RH200 Custom Hook-on Panels 1.0 GENERAL 1.1. Product Description RH200 system is a downward accessible, metal
More informationSAN DIEGO STATE UNIVERSITY PACIFIC CORNERSTONE ARCHITECTS TENOCHCA HALL PROJECT NO FAN COIL UNITS, RESTROOM AND FINISH RENOVATION
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Various gypsum board panels types. 2. Joint treatment materials. 3. Panel trim. 4. Supplementary components and accessories
More informationSECTION ACOUSTICAL CEILING SYSTEMS
SECTION 09 51 13 PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following: 1. Ceilings consisting of acoustical panels and exposed suspension systems. 2. T-Bar mounted light fixture support
More informationSECTION STEEL DECKING
SECTION 05 31 00 STEEL DECKING SPEC WRITER NOTE: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Refer to Section 05 36 00, COMPOSITE METAL DECKING for floor
More informationSECTION LINEAR METAL CEILINGS
PART 1 - GENERAL 1.1 DESCRIPTION: A. This Section Includes: SECTION 09 54 23 LINEAR METAL CEILINGS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or
More informationSubmittal Review A
Submittal Review TO: Pavilion Construction DATE: 07.20.2015 JOB NO.: 1484P 4700 SW Macadam Ave Suite 200 ATTENTION: Riley Tobin Portland, OR 97239 RE: BSD Sunset High School Concession Stand/Interior Renovations
More informationThe fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general specifications:
Query No.1 ; we need more specs. about fire resistant doors Answer to Query No. 1: The fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general
More informationSuspension Systems for Acoustical Lay-in Ceilings Seismic Design Categories D, E & F
NWCB Technical Document SUSPENDED CEILINGS 401 Suspension Systems for Acoustical Lay-in Ceilings Seismic Design Categories D, E & F 10/09 This document has been revised based on current Building Code standards.
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationA. Product Data: Submit manufacturer's descriptive literature, and recommendations and instructions for installation.
SECTION 09512 - ACOUSTICAL TILECEILINGS (ACT-01 and ACT-02) PART 1 - GENERAL 1.01 SUMMARY A. Section includes ceilings consisting of acoustical panels and exposed suspension systems. This ceiling system
More informationLINEAR METAL CEILINGS Section
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationAssemblies Evaluated For 1. Non Axial Load Bearing Wall 2. Transverse Load Capacity 3. Fire Resistance 4. Abuse Resistance
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Assembly Evaluation Report represents a product that Pei ES has Evaluated. This Assembly Evaluation
More informationA. This Section includes ceilings consisting of acoustical panels and exposed suspension systems.
SECTION 09 51 13 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More information1. Interior gypsum wallboard. 2. Exterior gypsum board panels for ceilings and soffits. 3. Tile backing panels.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationTHIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS. Though Rockfon Planostile Snap-In Metal Ceiling Panels are meant for interior and exterior applications, Specifications
More informationI-STUD Shaftwall System
I-STUD Shaftwall System Summit Tower Spokane, WA I-Stud and CertainTeed Shaftliner MILL CERTIFIED 00% GALVANIZED UL Evaluation Report No. ER3660-02 Intertek SCAFCO I-Stud is approved with the following
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationLather/Interior Systems Mechanic (ISM) Level 3
Level 3 B3 Blueprint Reading and Specifications 3 Duration: 35 hours 20 hours 15 hours This unit is designed to provide the apprentice with the knowledge and skills of blueprint reading and specifications.
More informationTHIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS. Rockfon CurvGrid One-Directional Curved Metal Ceiling Panels are meant for interior applications, specifications
More informationAssemblies Evaluated For 1. Non Axial Load Bearing Wall 2. Transverse Load Capacity 3. Fire Resistance 4. Abuse Resistance
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Assembly Evaluation Report represents a product that Pei ES has Evaluated. This Assembly Evaluation
More information1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets
SECTION 09 29 00 - GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation
More information