DIVISION 3 HEAVY DUTY CONCRETE FLOOR TOPPING SECTION 03340

Size: px
Start display at page:

Download "DIVISION 3 HEAVY DUTY CONCRETE FLOOR TOPPING SECTION 03340"

Transcription

1 DIVISION 3 HEAVY DUTY CONCRETE FLOOR TOPPING SECTION PART 1 - GENERAL 1.01 GENERAL REQUIREMENTS A. The General provisions of the contract, including GENERAL CONDITIONS, SUPPLEMENTARY CONDITIONS AND DIVISION I, GENERAL REQUIREMENTS apply to the work specified in this section. B. DEFINITIONS 1.02 DESCRIPTIONS 1. Heavy Duty Concrete Floor Manufacturer: A-H EMERY Aggregate Topping as manufactured by Anti-Hydro International, Flemington, NJ, 08822, (908) A. Work includes: Furnish all necessary materials, labor and equipment required to install heavy duty topping. B. Related work specified elsewhere: 1. Cast-in-Place Concrete, see Section Reinforcing steel, see Section Integral Hardener, see Section Concrete Finishing, see Section Concrete Curing, see Section Joint Sealants, see Section QUALITY ASSURANCE A. Manufacturer's Qualifications 1. Obtain heavy duty floor topping materials from a single manufacturer with a minimum of twenty-five (25) years of experience providing materials of the type specified in this section. 1

2 2. The heavy duty floor topping manufacturer shall provide a representative who will instruct the applicator's crew on the proper techniques of applying the heavy duty floor topping. B. Applicator's Qualifications 1.04 GUARANTEE 1. Installation shall be performed by a concrete contractor with not less than years of satisfactory experience in the application of the type of system as specified in this section, and shall be approved by the manufacturer of the heavy duty floor topping. A. The contractor shall furnish the manufacturer's standard maintenance guarantee of the heavy duty concrete floor topping for a period of five years after installation. This maintenance guarantee includes the bond and hard, non-dusting qualities of the floor. Not included are damage due to Acts of God or other elements beyond the scope of protection of this system. B. The integral hardening manufacturer shall review the proposed concrete mix design for all concrete containing integral hardening admixture and shall submit, in writing, acceptance of proposed mix. C. The contractor shall notify the heavy duty concrete floor topping manufacturer seven working days prior to system placement. D. Anti-Hydro International shall furnish daily inspections and reports of each day's placement furnished to the architect and/or engineer. The cost of the inspections is to be borne by the contractor SUBMITTALS A. Product Data 1. Submit manufacturer's technical data on specified products of the heavy duty concrete floor topping. 2

3 2. Submit a letter from the manufacturer certifying compliance with the requirements of sections 2.01.B and 2.01.C of this specification. 3. Submit independent test data using X-ray diffraction or other accepted method on EMERY aluminum oxide and ferric oxide contents. 4. Submit a list of three installations where this system has been in use for five years or greater. 5. Submit a specimen copy of the Daily Inspection Report and Five Year Maintenance Guarantee MATERIAL DELIVERY, HANDLING AND STORAGE A. Primary system materials shall be delivered in the manufacturer's undamaged, unopened containers. Each container shall be clearly marked with the following: 1. Product name 2. Manufacturer's name 3. Lot/Batch numbers B. Provide equipment and personnel to handle the materials by methods which prevent damage. C. The contractor shall promptly inspect all direct jobsite deliveries to assure that quantities are correct and that materials comply with requirements and are not damaged. D. The contractor shall be responsible for all materials furnished by him, and he shall replace, at his own expense, all such material that is found to be defective in manufacture or that has become damaged in transit, handling or storage. E. Store materials in accordance with manufacturer's instructions, with seals and labels intact and legible. Maintain temperatures within the required range. Do not use materials which have been stored for a longer period of time than the manufacturer's maximum recommended shelf life. All materials containing portland cement or 3

4 1.07 JOB CONDITIONS other hydrating powders are to be kept dry until use to prevent damage. A. During material application, care should be exercised to comply with the temperature and humidity limitations of the materials used as defined by the manufacturer. PART 2 - MATERIALS 2.01 PRODUCTS A. Concrete Base Slab: For concrete materials, see Section 03300, Cast-In-Place Concrete and provide additional items as required by this section. 1. Concrete base shall have a maximum of 3% air content. Do not use air entraining admixtures. 2. Concrete mix shall contain a minimum of 5.6 bags of Type I portland cement per cubic yard and not more than 32 gallons of total liquid. Add "ANTI-HYDRO" Integral Admixture at the rate of 1.5 gallons per cubic yard. 3. Do not use fly ash, cement substitutes or slag cement in mix design. B. Integral Hardening Admixture: "ANTI-HYDRO" Integral Hardening Admixture. The integral hardening admixture shall conform to the following requirements: 1. The admixture shall have a twenty year history of successful use in similar applications. 2. The admixture shall have been tested by an independent testing laboratory according to ASTM C-501 and shown to increase abrasion resistance of a 4000 psi concrete by 75%, minimum over a control mix without the admixture. 3. The admixture shall increase compressive strength of the concrete mix design at 28 days by 5%, 4

5 minimum a control mix of the same design without the admixture. 4. The admixture shall have been tested by an independent testing laboratory in accordance with ASTM E and shown to reduce water vapor transmission by one-half, minimum, over a control mix without the admixture and shall produce concrete with a perm rating of 0.04, minimum. C. Topping Aggregate: A-H EMERY, size A1, as manufactured by Anti-Hydro International, conforming to the following requirements: 1. Emery aggregate shall conform to Corps of Engineers CE-204 and shall consist of not less than 58% aluminum oxide and 24% ferric oxide. 2. Emery aggregate shall not be effected by freezing, moisture or cleaning compounds. 3. Emery aggregate shall be tested for conductivity and shall have a value of not more than 6.0 x 10-5 ohm-cm at room temperature. 4. Emery aggregate shall be crushed, factory graded, polyhedral in form and shall conform to the following gradation: Sieve Size %Retained 3/8 2-3 # # # # # #100 Trace D. A-H EMERY A1 PREMIX 1. A-H EMERY Aggregate shall be supplied "premixed", proportioned at the rate of 300 pounds of A-H EMERY 5

6 aggregate, 94 pounds of Type I portland cement, and workability agents. 2. A-H EMERY A1 PREMIX shall be mixed using clean equipment. Mixing liquid shall consist of "ANTI- HYDRO" integral floor hardener added with the mixing water. Use in accordance with the manufacturers' recommendations. NOTE TO SPECIFIER: SECTION 2.01 E.1. / Optional System E. A-H EMERY A1 AGGREGATE END OF NOTE. 1. A-H EMERY Aggregate shall be mixed at the site at the rate of 300 pounds of A-H EMERY Aggregate to 94 pounds of Type I portland cement. Mixing liquid shall consist of 1 quart "ANTI-HYDRO" Integral Hardening Admixture and not more than 4 gallons of total mixing liquid per bag of cement. 2. Compressive strength shall be tested in accordance with ASTM C-109 and shall produce minimum compressive strengths as below: 1 Day 6,000 psi 3 Days 8,000 psi 28 Days 14,000 psi 3. Flexural strength shall be tested in accordance with ASTM C-293 and shall produce minimum flexural strengths as follows: Flexural Strength: 7 Days 1,000 psi 28 Days 1,600 psi F. Bonding Agent: A-H EPOXY BONDING #125 or "ANTI-HYDRO" SLUSH COAT admixture, as manufactured by Anti-Hydro International. 6

7 G. Curing: A-H 3 WAY SEALER AIM as manufactured by Anti- Hydro International, consisting of a liquid type membrane-forming curing compound complying with ASTM-C- 309, Type I, Class A. Moisture loss not more than grams per square centimeter when applied at 200 square feet per gallon. H. Joint Sealant: Saw cut joints shall be filled with A-H GROOVE & CRACK FILLER #250, elastic type modified epoxy filler, per Section. I. Materials for this specification are based on products of Anti-Hydro International and terminology used may include reference to manufacturer's proprietary product. Such reference shall be construed only as establishing the quality of material and workmanship to be used under this section and shall not be construed as limiting competition. PART 3 - EXECUTION 3.01 CONCRETE PLACEMENT A. For concrete base slab placement, see Section 03300, and provide additional items required by this section SLAB SUB-BASE 1. Concrete base shall be placed at 3" maximum slump. 2. Add integral hardening admixture to the mixing water or to the partially mixed concrete and continue mixing for an additional 30 revolutions at mixing speed. A. The base to receive the concrete slab for the heavy duty concrete floor finish shall be well drained, uniformly well compacted and free of frost and foreign materials. The base shall be damp but free of standing water. B. No concrete shall be placed on wet or soggy ground without first laying and compacting a bed of broken stone or gravel of adequate thickness to prevent the mud from mixing with the concrete. 7

8 3.03 CONCRETE BASE SLAB A. NEW CONCRETE BASE SLAB 1. Place concrete base slab between screed points to minimize handling. Concrete shall be placed and screeded using proper tools and equipment to prevent segregation. Use square tipped shovels to move concrete into place; do not use rakes. 2. Surface of base must be textured before concrete achieves final set. Texturing is done by cutting ribs in the surface with a coarse wire broom. The presence of laitance on the hardened base slab shall not be permitted. Water cure only. B. EXISTING CONCRETE BASE SLAB 1. Clean, and prepare existing concrete floor slabs with scarifying, shotblast, or waterblast equipment to a sufficient depth beyond the point of any contamination and loose materials. 2. Remove debris from jobsite. Powerwash the prepared surface to remove loose material. Cover base slab with polyethylene sheets if the topping application is delayed for more than 48 hours or the base slab is subject to debris or contamination from other trades APPLICATION OF TOPPING A. Surface Preparation: The concrete base slab shall be cleaned, dampened and treated with a slush coat consisting of 1 part "ANTI-HYDRO" Admixture, 3 parts water and enough Type I portland cement to make a creamy slurry. 1. Scrub slush coat into base surface with a stiff broom and place topping while slush coat is still wet. 8

9 B. Follow manufacturers instructions for epoxy bonding application. C. Topping: Mix topping as specified under section , and in accordance with manufacturer's instructions. D. Emery topping shall be straight edged or rolled level, immediately followed by bull floating or "darbying" for secondary leveling and compaction FINISHING A. After the topping has been allowed to stiffen (sustain foot pressure with no greater than 1/4" indentation), the first floating operation shall start. After completion of this operation, the topping shall be allowed to stiffen further. A second floating operation shall be done perpendicular to the first float. B. For subsequent trowelings, the blades of the power trowel shall be slightly tilted to produce a hard, smooth, finished surface free from chatter marks or blemishes. For further burnishing, continue troweling operation JOINTS A. Control Joints 1. Control joints shall be spaced in accordance with ACI Standard Concrete Floor and Slab Construction. All joints in base concrete must be carried through the topping. 2. Control joints shall be saw cut a minimum of 1/4 of the thickness of the concrete base slab and 2/3 the thickness of the A-H EMERY Topping. Cuts must be made as soon as the concrete or topping can be cut without raveling the edge, but not more than 24 hours after finishing. 3. Joints shall be filled with A-H GROOVE & CRACK FILLER #250, elastic type modified epoxy joint 9

10 filler per Section, at a minimum of 28 days after concrete placement. B. Construction Joints 1. Construction joints shall be keyed or doweled for load transfer as shown on the drawings. Construction joint edges in the topping should be compacted with a small radius edging tool. 2. Joints shall be filled with A-H GROOVE & CRACK FILLER #250, elastic type modified epoxy joint filler per Section, at a minimum of 28 days after concrete placement CURING AND PROTECTION A. The base Concrete and topping should be wet cured for a minimum of seven days in accordance with the provisions of ACI 302.1R-30, Section 8.1. B. As soon as the topping has been finished according to the provisions of section 3.05 of this specification, apply A-H 3 WAY SEALER AIM at the rate of square feet per gallon. Allow to dry and immediately flood the topping with water. Cover with wet burlap and polyethylene. Maintain wet cure for a period of 7 days, minimum. C. Concrete base and topping shall not be placed in temperatures over 80 deg. F, in the direct rays of the sun, or are exposed to drying winds. Care should be taken to prevent water loss. Erect wind barriers, finish the concrete promptly and start wet curing immediately. D. Floor topping should not be subjected to traffic during the 7 day water curing period. If the slab is to be subjected to heavy traffic during the first two weeks, it should be protected by plywood sheets or planking QUALITY CONTROL TESTING DURING CONSTRUCTION 10

11 A. Quality control testing of base concrete shall conform to the requirements of Section 03300, "Cast In Place Concrete," section B. Quality control testing of EMERY aggregate topping shall conform to the requirements of this section. C. The Owner will employ an inspector and testing laboratory approved by the Architect/Engineer to perform tests and to submit test reports to the local authorities, Owner, Architect, Engineer and Contractor. D. Sampling and testing for quality control during placement of topping may include the following, as directed by Owner's inspector. E. Compressive Strength of Hydraulic Cement Mortars: ASTM C Emery Aggregate Topping Temperature: Test hourly when air temperature is 50 degrees Fahrenheit and below, and when 80 degrees Fahrenheit and above; and each time a set of compression test specimens are made. 2. Compressive Strength Tests: ASTM C , one set (6 cubes 2" x 2" x 2") for each 3 cubic yards of EMERY aggregate topping placed for each day's pour; two specimens tested at 3 days, two specimens tested at 7 days, and two specimens tested at 28 days. Mold and store cubes for laboratory cured test specimens. 3. Strength level of cubes will be considered satisfactory if averages of sets of strength test results equal or exceed specified compressive strength, and no individual strength test result falls below specified compressive strength by more than 85%. F. Test results will be reported in writing to Architect, Structural Engineer and Contractor within 24 hours after tests. Reports of compressive strength tests shall contain the project identification name and number, date 11

12 3.09 JOB COMPLETION REV.8/14 HDCFT.DOC of topping placement, name of concrete testing service, location of topping batch in structure, and design compressive strength at 28 days. A. The Heavy Duty Floor Topping manufacturer shall inspect the completed hardened floor according to the manufacturer's guarantee provisions. The contractor shall correct all defects to meet this specification and those of the EMERY topping manufacturer. B. Clean up all debris, excess materials and equipment and remove from site. C. Guarantee paperwork must be processed within 60 days from the date of substantial completion. END OF SECTION 12

SECTION SITE CONCRETE

SECTION SITE CONCRETE SECTION 321313 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS SECTION 09699 MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS PART 1 GENERAL 1.1 SECTION INCLUDES A. Testing and application of systems for the reduction of moisture resistant or water-proof

More information

PART 1 - GENERAL. Section Cast-in-Place Concrete 1.3 REFERENCES

PART 1 - GENERAL. Section Cast-in-Place Concrete 1.3 REFERENCES CSI SECTION 32 13 13 CONCRETE PAVING 32 01 26 RIGID PAVING REHABILITATION DOT APPROVED PRODUCTS LIST OR SPECIAL PROVISIONS Very Early High Strength, Low Shrinkage, Powder Polymer-Modified Concrete Overlay

More information

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING

More information

1.1 Related Work Specified in Other Sections (Delete if Not Applicable):

1.1 Related Work Specified in Other Sections (Delete if Not Applicable): NOTE TO SPECIFIER: Concrete Resurfacing (Broom Finish) System provides an economical alternative to the removal and replacement of existing concrete. This system creates a flexible and durable finish that

More information

KOSTER AMERICAN CORPORATION

KOSTER AMERICAN CORPORATION Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General

More information

SECTION CAST-IN-PLACE CONCRETE

SECTION CAST-IN-PLACE CONCRETE SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. The Contractor shall furnish all work and materials, including cement, sand and coarse aggregate, water, admixtures, curing

More information

SPECIFICATIONS FOR CAST-IN-PLACE CONCRETE SLAB DUNN COUNTY TRANSFER STATION MENOMONIE, WISCONSIN

SPECIFICATIONS FOR CAST-IN-PLACE CONCRETE SLAB DUNN COUNTY TRANSFER STATION MENOMONIE, WISCONSIN SPECIFICATIONS FOR CAST-IN-PLACE CONCRETE SLAB DUNN COUNTY TRANSFER STATION MENOMONIE, WISCONSIN 1. SUMMARY A. Work includes: 1. Pavement removal, topsoil stripping, and site grading for concrete slab.

More information

Fundamentals of Concrete

Fundamentals of Concrete Components Cement Water Fine Aggregate Coarse Aggregate Fundamentals of Range in Proportions Advantages of Reducing Water Content: Increased strength Lower permeability Fundamentals of Increased resistance

More information

A. Drawings and general provisions of the contract, including General and Supplementary Conditions, apply to this section.

A. Drawings and general provisions of the contract, including General and Supplementary Conditions, apply to this section. SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE SECTION 03 01 40 MAINTENANCE OF PRECAST CONCRETE SECTION 03 01 50 MAINTENANCE OF CAST DECKS AND UNDERLAYMENT SECTION 03 01 60 MAINTENANCE OF GROUTING

More information

INDUSTRY RECOMMENDATION EXTERIOR CONCRETE FLATWORK

INDUSTRY RECOMMENDATION EXTERIOR CONCRETE FLATWORK INDUSTRY RECOMMENDATION for EXTERIOR CONCRETE FLATWORK Prepared by Ohio Concrete Inquires regarding this document may be addressed to: Ohio Concrete 2600 Corporate Exchange Dr., Ste. 165 Columbus, OH 43231

More information

By CTS Cement Manufacturing Corp.

By CTS Cement Manufacturing Corp. CSI SECTION 03 60 00 GROUTING 03 62 00 NON-SHRINK GROUTING 03 62 13 NON-METALLIC NON-SHRINK GROUTING High Flow, Non-Metallic, Multi-Purpose, Cementitious, Non-Shrink Grout EDITOR NOTE: The following guideline

More information

Narrow Modular Pavers (NMP) for Sand-Set Installations

Narrow Modular Pavers (NMP) for Sand-Set Installations The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Sand-Set Installations Narrow Modular Pavers are part of the California Architectural Paver line

More information

SECTION CONCRETE PAVING SLABS SET IN MORTAR

SECTION CONCRETE PAVING SLABS SET IN MORTAR SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints

More information

BIO-AQUIFER STORM SYSTEM

BIO-AQUIFER STORM SYSTEM BIO-AQUIFER STORM SYSTEM Specifications for Construction PART 1 GENERAL 1.01 SECTION INCLUDES A. Providing labor, materials, tools and equipment to furnish and install a permeable concrete paving stone

More information

SECTION EPOXY FLOORING SYSTEMS

SECTION EPOXY FLOORING SYSTEMS SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

A. ASTM C 150 Standard Specification for Portland Cement. B. ASTM C 595 Standard Specification for Blended Hydraulic Cements.

A. ASTM C 150 Standard Specification for Portland Cement. B. ASTM C 595 Standard Specification for Blended Hydraulic Cements. TECHNICAL SPECIFICATIONS SEWER MANHOLE REHABILITATION SYSTEM WITH A PROTECTIVE CEMENT LINER AND HIGH BUILD EPOXY COATING (As Provided by Standard Cement Materials) FOREWORD The following specification

More information

CELCORE CELLULAR INSULATING CONCRETE SPECIFICATION FOR RETROFIT PLACEMENT OVER EXISTING ROOF MEMBRANES

CELCORE CELLULAR INSULATING CONCRETE SPECIFICATION FOR RETROFIT PLACEMENT OVER EXISTING ROOF MEMBRANES PART 1: SCOPE CELCORE CELLULAR INSULATING CONCRETE SPECIFICATION FOR RETROFIT PLACEMENT OVER EXISTING ROOF MEMBRANES 1.1 An Approved Celcore Applicator shall furnish all labor, materials and supervision

More information

A. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT).

A. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT). SECTION 32 01 16 ASPHALT OVERLAY PART 1 - GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for scarifying, grinding, sweeping and repair of existing asphalt concrete pavement to establish

More information

for Mortar-Set Concrete Tiling Installations

for Mortar-Set Concrete Tiling Installations The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural

More information

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS SECTION 03 05 00 COMMON WORK RESULTS FOR CONCRETE 09 97 00 SSPECIALTY COATINGS Weld Crete ************************************************************************************************************************

More information

CRUSHED AGGREGATE BLENDED WITH GRANITECRETE ADMIXTURE SURFACING

CRUSHED AGGREGATE BLENDED WITH GRANITECRETE ADMIXTURE SURFACING Guide Specification CRUSHED AGGREGATE BLENDED WITH GRANITECRETE ADMIXTURE SURFACING COORDINATE WITH DRAWINGS: Show location and extent of stabilized aggregate surfacing. Show details required at adjoining

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,

More information

ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS

ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS 6.1 DESCRIPTION This work shall consist of constructing curbs, gutters, sidewalks, ramps, local depressions and driveways of the form and dimensions shown

More information

Kolorines Glass Mosaic Tiles Project Specification

Kolorines Glass Mosaic Tiles Project Specification Kolorines Glass Mosaic Tiles Project Specification SUGGESTED SPECIFICATION Glass Mosaic Tile Installation for Swimming Pools NOTES TO SPECIFIER: 1. Specify PremiumPlus Thin-Set mixed with CustomFlex Additive

More information

PAVING SLABS ON A CONCRETE BASE

PAVING SLABS ON A CONCRETE BASE SECTION 32 14 13.16 PAVING SLABS ON A CONCRETE BASE (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs on a sand bed over concrete for pedestrian applications.

More information

UFGS (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS

UFGS (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-07 16 19 (January 2007) ---------------------------- Preparing Activity: NAVFAC Replacing without change UFGS-07 16 19 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS

More information

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3

More information

DIVISION 03 CONCRETE CONCRETE Maintenance of Concrete

DIVISION 03 CONCRETE CONCRETE Maintenance of Concrete DIVISION 03 CONCRETE 03 00 00 CONCRETE 03 01 00 Maintenance of Concrete 03 01 10 Maintenance of Concrete Forming and Accessories 03 01 20 Maintenance of Concrete Reinforcing 03 01 23 Maintenance of Stressing

More information

B. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.

B. Related Sections: 1. Division 07 Section Joint Sealants for sealing of expansion, contraction, control, and isolation joints in tile surfaces. SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Engine Bay Floors Floor Resurfacing 4000

Engine Bay Floors Floor Resurfacing 4000 Engine Bay Floors Floor Resurfacing 4000 P.O. Box 341 Macungie, PA 18062 610.530.7710 800.573.9198 www.enginebayfloors.com 1.1 SUBMITTALS Flooring Specification SECTION 1 GENERAL A. Product Data: Submit

More information

SECTION TILING

SECTION TILING SECTION 09 30 00 TILING PART 1 - GENERAL 1.1 SUMMARY A. Section includes tile as indicated on new surfaces and as specified. 1.2 SUBMITTALS A. Samples: 1. Submit samples of colors and sizes of tile. B.

More information

September 1, 2003 CONCRETE MANUAL SPECIAL TYPES OF CONCRETE

September 1, 2003 CONCRETE MANUAL SPECIAL TYPES OF CONCRETE September 1, 2003 CONCRETE MANUAL 5-694.800 5-694.810 GENERAL SPECIAL TYPES OF CONCRETE 5-694.800 In the general use of the word concrete, the idea implied is the conventional placement of the material

More information

Construction Standard Specification Section Exposed Aggregate Concrete. Exposed Aggregate Concrete

Construction Standard Specification Section Exposed Aggregate Concrete. Exposed Aggregate Concrete Construction Standard Specification Section 03351 Exposed Aggregate Concrete Exposed Aggregate Concrete Part 1 GENERAL 1.01 Summary A. Section includes: Exposed Aggregate Concrete produced through the

More information

A. Section includes cast-in-place concrete, including formwork, reinforcement, concrete materials, mixture design, placement procedures, and finishes.

A. Section includes cast-in-place concrete, including formwork, reinforcement, concrete materials, mixture design, placement procedures, and finishes. SECTION 033000 - PART 1 - GENERAL 1.1 SUMMARY A. Section includes cast-in-place concrete, including formwork, reinforcement, concrete materials, mixture design, placement procedures, and finishes. B. Related

More information

SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS ; /19; ;

SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS ; /19; ; SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS 01 71 16; 02 25 16/19; 03 01 30; 0716 16 SUPER-KRETE International, Inc. This product guide specification is written according

More information

SECTION ARCHITECTURAL CAST STONE

SECTION ARCHITECTURAL CAST STONE PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 047200 ARCHITECTURAL CAST STONE A. RELATED DRAWINGS All drawings, to include supplemental drawings, instructions and conditions of this contract. B. RELATED

More information

B. All work of the section shall comply with the conditions of the contract, the drawings and any special conditions forming a part of the contract.

B. All work of the section shall comply with the conditions of the contract, the drawings and any special conditions forming a part of the contract. SPECIFICATIONS PART ONE - GENERAL ------------------------------------------------------------------------ 1.01 General Description A. The Cementitious capillary waterproofing materials specified herein

More information

PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960

PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary

More information

SECTION UTILITY MANHOLES AND STRUCTURES

SECTION UTILITY MANHOLES AND STRUCTURES SECTION 33 05 14 UTILITY MANHOLES AND STRUCTURES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Precast reinforced concrete manholes and structures with tongue-and-groove joints with masonry transition

More information

A. The scope of this standard includes recommendations for the specification of cast-in-place concrete.

A. The scope of this standard includes recommendations for the specification of cast-in-place concrete. PART 1: GENERAL 1.01 Scope of Standard A. The scope of this standard includes recommendations for the specification of cast-in-place concrete. 1.02 Related Standards A. Structural Systems (currently The

More information

TILE TILE

TILE TILE 09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements

More information

prospec.com Concrete Repair & Restoration

prospec.com Concrete Repair & Restoration prospec.com Concrete Repair & Restoration Table of Contents Product Portfolio 3 Product Enhancements 4 Product Selection Matrices 5 Construction Grout & Precast Non-shrink grouts C-1107 Construction Grout

More information

Construction Standard Specification Section Exposed Aggregate Concrete

Construction Standard Specification Section Exposed Aggregate Concrete Construction Standard Specification Section 03351 Exposed Aggregate Concrete Part 1 GENERAL 1.01 Summary A. Section includes: Exposed Aggregate Concrete produced through the use of a chemical surface retarder

More information

1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.

1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU. 1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate

More information

TECHNICAL SPECIAL PROVISION FOR CONCRETE REPAIRS. Financial Project ID , &

TECHNICAL SPECIAL PROVISION FOR CONCRETE REPAIRS. Financial Project ID , & TECHNICAL SPECIAL PROVISION FOR CONCRETE REPAIRS Financial Project ID 429140-1-52-01, 429140-2-52-01 & 428267-1-52-01 The official record of this Technical Special Provision is the electronic file signed

More information

SECTION HYDRAULIC CEMENT UNDERLAYMENT

SECTION HYDRAULIC CEMENT UNDERLAYMENT ARDEX GUIDE SPECIFICATION ARDEX Underlayment HC 100 High-Capacity Self-Leveling and V1200 Self-Leveling Flooring Underlayment Cement-based Self-Leveling Underlayment for use with ARDEX ARDIFLO System SECTION

More information

ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED)

ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED) ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED) 275.1. Description. This Item shall govern for treating subgrade, new and/or existing base [with or without asphaltic concrete pavement (ACP)], or

More information

FIVE STAR PRODUCTS, INC. (800)

FIVE STAR PRODUCTS, INC.  (800) FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 11 DESIGN-A-SPEC GUIDELINES FIVE STAR RS ANCHOR GEL CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS PART

More information

Best Management Standards / Specifications. For Concrete Slab Raising. Prepared in conjunction with the Concrete Repair Association

Best Management Standards / Specifications. For Concrete Slab Raising. Prepared in conjunction with the Concrete Repair Association For Concrete Slab Raising Prepared in conjunction with the Concrete Repair Association DETAILED SPECIFICATIONS 1. Description: 2. Slab Raising: These specifications cover the furnishing, boring, drilling,

More information

It s in the Pour Gla-Zit does so much for all types of new concrete projects no Pour should be without it. Gla-Zit.com

It s in the Pour Gla-Zit does so much for all types of new concrete projects no Pour should be without it. Gla-Zit.com It s in the Pour Gla-Zit is a unique liquid, added to cement for waterproofing/densifying concrete masonry and Ready-Mix product. Add Gla-Zit as the last material, mix for three (3) minutes and Pour. Gla-Zit

More information

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE

More information

CEMENTITIOUS CRYSTALLIZING WATERPROOFING PART 1 GENERAL

CEMENTITIOUS CRYSTALLIZING WATERPROOFING PART 1 GENERAL CEMENTITIOUS CRYSTALLIZING WATERPROOFING PART 1 GENERAL 1.1 SECTION INCLUDES A. Cementitious crystallizing waterproofing for interior/exterior walls and floor slabs with nonactive leaks. B. Cementitious

More information

PRODUCT SPECIFICATIONS

PRODUCT SPECIFICATIONS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below

More information

SECTION 3300 CAST-IN-PLACE CONCRETE

SECTION 3300 CAST-IN-PLACE CONCRETE SECTION 3300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 DESCRIPTION A. This Section includes furnishing materials and installation of cast-in-place concrete as indicated on the Drawings and/or specified

More information

Editing notes to assist users are separated from specification text by rows of asterisks. Delete these notes prior to final printing.

Editing notes to assist users are separated from specification text by rows of asterisks. Delete these notes prior to final printing. SECTION 09635 LIMESTONE FLOORING This guide specification has been prepared by TexaStone Quarries LLC to assist design professionals in the preparation of a specification section covering cut limestone

More information

Section Polished Concrete Finishing. Vexcon

Section Polished Concrete Finishing. Vexcon SS 105 5-16 Section 03 35 43 Polished Concrete Finishing Specifier Note: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-part format. This section

More information

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings. SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

STANDARD SPECIFICATION FOR CRIBLOCK CONCRETE CRIBWALL

STANDARD SPECIFICATION FOR CRIBLOCK CONCRETE CRIBWALL STANDARD SPECIFICATION FOR CRIBLOCK CONCRETE CRIBWALL 1. SCOPE 2. DESIGN 3. MATERIALS 4. CONSTRUCTION 5. METHOD OF MEASUREMENT AND PAYMENT SCOPE This Specification sets out requirements for the design,

More information

Concrete. Chapter 10 Properties of Fresh Concrete. Materials of Construction-Concrete 1. Wikipedia.org

Concrete. Chapter 10 Properties of Fresh Concrete. Materials of Construction-Concrete 1. Wikipedia.org Wikipedia.org Concrete Chapter 10 Properties of Fresh Concrete Materials of Construction-Concrete 1 What is Concrete? Concrete is a composite material that consists of a cement paste within which various

More information

SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE. Product. Scope. Appraisal No. 811 [2013] Appraisal No. 811 (2013) Amended 28 August 2017

SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE. Product. Scope. Appraisal No. 811 [2013] Appraisal No. 811 (2013) Amended 28 August 2017 SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE Amended 28 August 2017 BRANZ Appraisals Technical Assessments of products for building and construction. Sika (NZ) Ltd PO Box 19 192 Avondale Auckland 1746

More information

Coloured Mineral Dry Shake Floor Hardener

Coloured Mineral Dry Shake Floor Hardener Construction Product Data Sheet Edition: 27/02/2013 Identification no: 02 08 03 04 001 0 000013 Version: GCC Coloured Mineral Dry Shake Floor Hardener Product Description is a one part, pre-blended, coloured

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-03 37 13 (November 2009) ----------------------------- Preparing Activity: USACE Superseding UFGS-03 37 13 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

SECTION Pedestrian Traffic Coatings{PRIVATE } 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary)

SECTION Pedestrian Traffic Coatings{PRIVATE } 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) Guide Specification MiraFlex II For Plywood Decks Pedestrian Deck and Waterproofing System (Specification writer shall choose the most appropriate section that applies to a given scope of work, including

More information

SPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 5/8/7)

SPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 5/8/7) Page 1 of 7 STONE STRONG SYSTEMS SPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 5/8/7) PART 1: GENERAL 1.01 Description A. Work includes furnishing and installing precast modular

More information

2018 Flooring Specification - Tile Set Method TECTURA DESIGNS CEMENT TERRAZZO TILES

2018 Flooring Specification - Tile Set Method TECTURA DESIGNS CEMENT TERRAZZO TILES 2018 Flooring Specification - Tile Set Method 09300 TECTURA DESIGNS CEMENT TERRAZZO TILES PART 1 - GENERAL 1.1 INTRODUCTION A. Tectura Designs, Terrazzo Tiles are to be installed following the tile setting

More information

GUIDE SPECIFICATION

GUIDE SPECIFICATION GUIDE SPECIFICATION 09 64 33.01 940 Centre Circle, Suite 1000 Altamonte Springs, FL 32714 Telephone: 407-260-9910 Fax: 407-260-9933 Toll Free: 800-800-5247 Web Site: http://www.kahrs.com This Guide Specification

More information

Pacific Polymers Elasto-Deck BT Guide Specification

Pacific Polymers Elasto-Deck BT Guide Specification 1 07141-1 August 2016 Pacific Polymers Elasto-Deck BT Guide Specification SECTION 07141 FLUID APPLIED WATERPROOFING 2 07141-2 August 2016 Pacific Polymers Elasto-Deck BT Guide Specification SECTION 07141

More information

PRODUCT GUIDE SPECIFICATION

PRODUCT GUIDE SPECIFICATION PRODUCT GUIDE SPECIFICATION Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,

More information

SPECIFICATION GUIDELINE

SPECIFICATION GUIDELINE SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification

More information

Guide to Improving Specifications for Ready Mixed Concrete

Guide to Improving Specifications for Ready Mixed Concrete NRMCA Publication 2PE004 Guide to Improving Specifications for Ready Mixed Concrete 2015 National Ready Mixed Concrete Association All rights reserved NRMCA Publication 2PE004 Guide to Improving Specifications

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09 66 23.16 EPOXY TERRAZZO THIS GUIDE SPECIFICATION HAS BEEN PREPARED BY THE NATIONAL TERRAZZO AND MOSAIC ASSOCIATION, INC., AND IS DISTRIBUTED FOR USE BY ITS MEMBERS AND DESIGN PROFESSIONALS.

More information

Tolerances- Section

Tolerances- Section Tolerances- Section 346-6.4 Do not add water to delivered concrete when it is within the target Range for slump 1 346-6.4 Tolerances: Meet the following tolerances from target values for plastic concrete

More information

SECTION RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 09 66 23 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION ROOF PEDESTAL PAVER SYSTEM

SECTION ROOF PEDESTAL PAVER SYSTEM SECTION 07 76 00 ROOF PEDESTAL PAVER SYSTEM ************************************************************************************************************************ Edit entire master to suit project requirements.

More information

Technical Memorandum No. MERL Quality Management Plan Guidance for Concrete used for Construction of Significant Features

Technical Memorandum No. MERL Quality Management Plan Guidance for Concrete used for Construction of Significant Features Quality Management Plan Guidance for Concrete used for Construction of Significant Features 1. 2. U.S. Department of the Interior Bureau of Reclamation Technical Service Center Denver, Colorado August

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell WB 50 Product Specification GUIDE SPECIFICATION SECTION 09725

More information

GUIDE SPECIFICATIONS For STRUCTURAL PRECAST HOLLOW CORE SLABS SECTION 03410

GUIDE SPECIFICATIONS For STRUCTURAL PRECAST HOLLOW CORE SLABS SECTION 03410 GUIDE SPECIFICATIONS For STRUCTURAL PRECAST HOLLOW CORE SLABS SECTION 03410 Note to user: These guide specifications are provided by Mid- States Concrete Products as a service to you; they are NOT specific

More information

A. Texas Department Transportation 2004 Standard Specifications for Construction of Highways, Streets and Bridges (TxDOT):

A. Texas Department Transportation 2004 Standard Specifications for Construction of Highways, Streets and Bridges (TxDOT): SECTION 31 32 13.16 CEMENT STABILIZATION PART 1 GENERAL 1.1 SCOPE OF WORK A. This Section pertains to the specifications for cement stabilization of sandy or silty soil and consists of pulverizing, addition

More information

ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT

ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 9/30/2009 AC 150/5370-10E ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 631-1.1 GENERAL. This item shall consist of a mixture of refined coal tar emulsion, mineral

More information

LS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION

LS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION LS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION A. Section Includes B. References C. Quality Assurance D. Submittals E. Delivery, Storage and Handling F. Environmental Conditions G. Summary H. Concrete

More information

SECTION INTERLOCKING CONCRETE PAVERS

SECTION INTERLOCKING CONCRETE PAVERS SECTION 23 14 13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for concrete paver applications in the U.S. for concrete pavers and bedding sand over a compacted

More information

Application Instructions for Keystone Kool Deck on Existing Concrete

Application Instructions for Keystone Kool Deck on Existing Concrete Application Instructions for Keystone Kool Deck on Existing Concrete REQUIRED MATERIALS Keystone Kool Deck PTA Bonding Agent Water 20 Mesh Marble Sand White Portland Cement OPTIONAL TOOLS Mortex Pattern

More information

DECORATIVE EXTERIOR FINISHING

DECORATIVE EXTERIOR FINISHING System Guide Specification for Super-Krete Stain and Seal System S-9550 SECTION 03 35 00 Concrete Finishing and SECTION 09 93 13 Exterior Staining and Transparent Finishing DECORATIVE EXTERIOR FINISHING

More information

Construction. SikaTop 111 Plus. Application Instructions. Sika Corporation

Construction. SikaTop 111 Plus. Application Instructions. Sika Corporation SikaTop 111 Plus Application Instructions SikaTop 111 Plus Two-component, polymer-modified, portland cement based. Fast-setting, screed mortar. Performance repair mortar for horizontal repairs and form

More information

International Polished Concrete Institute November 2006 Toll Free (866) Website

International Polished Concrete Institute November 2006 Toll Free (866) Website International Polished Concrete Institute November 2006 Toll Free (866) 421-9550 Website www.ipcionline.org E-mail info@ipcionline.org SECTION 03365 POLISHED CONCRETE FLOOR SYSTEM PART 1 GENERAL 1.1 SECTION

More information

Kinds of Mortars. Mortar. Specifying Mortar. Proportion Specifications. M a S o N w O r K. Specification for Mortar Cement

Kinds of Mortars. Mortar. Specifying Mortar. Proportion Specifications. M a S o N w O r K. Specification for Mortar Cement ASTM C9 ASTM C44 ASTM C270 ASTM C780 ASTM C329 ASTM C586 Mortar Specification for Masonry Specification for Aggregate for Masonry Mortar Specification for Mortar for Unit Masonry Method for Preconstruction

More information

CITY OF FARGO SPECIFICATIONS CONCRETE SIDEWALKS AND DRIVEWAYS

CITY OF FARGO SPECIFICATIONS CONCRETE SIDEWALKS AND DRIVEWAYS CONCRETE SIDEWALKS AND DRIVEWAYS PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of all labor, material, and equipment necessary

More information

***********************************************************************************

*********************************************************************************** AQUAFIN-2K/M Two-Component Cement-based Acrylic-based Waterproofing GUIDE AQUAFIN, Inc. SPECIFICATION PART 1 - GENERAL 1.1 SECTION INCLUDES SECTION 07 16 14 ACRYLIC MODIFIED (FLEXIBLE) CEMENTITIOUS WATERPROOFING

More information

Fiber Reinforced Tile and Stone Mortar

Fiber Reinforced Tile and Stone Mortar , ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or

More information

CW 3615 RIPRAP TABLE OF CONTENTS

CW 3615 RIPRAP TABLE OF CONTENTS December 2014 SPECIFICATION CW 3615 R4 CW 3615 RIPRAP TABLE OF CONTENTS 1. GENERAL CONDITIONS... 1 3. DESCRIPTION... 1 5. MATERIALS... 1 5.1 General... 1 5.2 Rock... 1 5.3 Random Stone Riprap... 1 5.4

More information

Project Address: Name of Person Completing Form:

Project Address: Name of Person Completing Form: Statement of Inspections This form is provided as a way to list aspects of the project that require special inspection and testing in accordance with IBC Sections 107.1, 1704, and 1705 and define duties

More information

1. Cast-in-place concrete is specified in Section

1. Cast-in-place concrete is specified in Section SECTION 03 38 00 PART 1 - GENERAL 1.01 DESCRIPTION A. This Section describes the requirements for furnishing and installing post-tensioned slabs, jacks, jacking and anchors at Parking Structure, and record

More information

Application Specification:

Application Specification: Application Specification: GW-15-UBU-HD April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR VEHICULAR TRAFFIC DECKS AND RAMPS

More information

Municipality of Waterville Public Sidewalk Repair Policy

Municipality of Waterville Public Sidewalk Repair Policy Municipality of Waterville Public Sidewalk Repair Policy Purpose - The purpose of this policy is to protect the public health, safety and welfare of the citizens and inhabitants of the Municipality by

More information

1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards

1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards SECTION 07185 TRAFFIC MEMBRANE PART 1 GENERAL 1.1 SECTION INCLUDES A. Traffic membrane, consisting of welded seam PVC waterproofing, over f following surfaces: 1. Decks, balconies, and sun porches 2. Walkways,

More information

INSULATED CONCRETE MASONRY UNITS Section 04220

INSULATED CONCRETE MASONRY UNITS Section 04220 INSULATED CONCRETE MASONRY UNITS Section 04220 PART 1 GENERAL 1.01 Summary A. Section Includes 1. Insulated masonry wall units (CMU's) 2. Decorative insulated masonry wall units 1.02 SUBMITTALS A. Samples:

More information

CHATTANOOGA, TN Last Updated: 04/12/17. NOTE TO SPECIFIER: Be sure to obtain the latest version of this Guide Specification.

CHATTANOOGA, TN Last Updated: 04/12/17. NOTE TO SPECIFIER: Be sure to obtain the latest version of this Guide Specification. NOTE TO SPECIFIER: Be sure to obtain the latest version of this Guide Specification. This Guide Specification is not a completed document ready for use. It must be edited (i.e., deleting, adding, or modifying

More information