SECTION ELASTOMERIC MEMBRANE ROOFING
|
|
- Hillary O’Neal’
- 6 years ago
- Views:
Transcription
1 SECTION PART 1 GENERAL 1.01 SECTION INCLUDES A. Elastomeric roofing membrane, mechanically fastened conventional application. B. Insulation, flat and tapered. C. Flashings. D. Roofing cant strips, stack boots, roofing expansion joints, and walkway pads RELATED REQUIREMENTS A. Section Rough Carpentry: Wood nailers and curbs. B. Section Sheet Metal Flashing and Trim: Counterflashings, reglets,. C. Section Roof Accessories: Roof-mounted units; prefabricated curbs REFERENCE STANDARDS A. ASTM C Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board; B. ASTM D412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers- Tension; 2006a (Reapproved 2013). C. ASTM D624 - Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers; 2000 (Reapproved 2012). D. ASTM D746 - Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact; E. ASTM D Standard Test Method for Rubber Property--Durometer Hardness; 2005 (Reapproved 2010). F. ASTM D4637/D4637M - Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane; G. ASTM E96/E96M - Standard Test Methods for Water Vapor Transmission of Materials; H. FM DS Wind Design; Factory Mutual Research Corporation; I. NRCA ML104 - The NRCA Roofing and Waterproofing Manual; National Roofing Contractors Association; Fifth Edition, with interim updates. J. UL (RMSD) - Roofing Materials and Systems Directory; Underwriters Laboratories Inc.; current edition SUBMITTALS A. See Section Administrative Requirements, for submittal procedures. Edison Elementary Addition - Bid Package
2 B. Product Data: Provide data indicating membrane materials, flashing materials, insulation, and fasteners. C. Shop Drawings: Indicate joint or termination detail conditions, conditions of interface with other materials, setting plan for tapered insulation, and paver layout. D. Warranty: Submit manufacturer warranty and ensure forms have been completed in Owner's name and registered with manufacturer QUALITY ASSURANCE A. Perform work in accordance with NRCA Roofing and Waterproofing Manual and manufacturer's instructions. B. Manufacturer Qualifications: Company specializing in manufacturing the products specified in this section with minimum three years of documented experience. C. Installer Qualifications: Company specializing in performing the work of this section with minimum three years documented experience, and approved by manufacturer DELIVERY, STORAGE, AND HANDLING A. Deliver products in manufacturer's original containers, dry, undamaged, with seals and labels intact. B. Store products in weather protected environment, clear of ground and moisture. C. Protect foam insulation from direct exposure to sunlight FIELD CONDITIONS A. Do not apply roofing membrane during unsuitable weather. B. Do not apply roofing membrane when ambient temperature is below 40 degrees F (5 degrees C) or above 100 degrees F (38 degrees C). C. Do not apply roofing membrane to damp or frozen deck surface or when precipitation is expected or occurring. D. Do not expose materials vulnerable to water or sun damage in quantities greater than can be weatherproofed the same day WARRANTY A. See Section Closeout Submittals, for additional warranty requirements. B. Correct defective Work within a two year period after Date of Substantial Completion. C. General Warranty: The warranties specified in this Article shall not deprive the Owner of other rights the Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by the Contractor under requirements of the Contract Documents. D. Provide 20 year manufacturer's material and labor warranty to cover failure to prevent penetration of water. Edison Elementary Addition - Bid Package
3 PART 2 PRODUCTS 2.01 MANUFACTURERS A. EPDM Membrane Materials: 1. Carlisle Roofing Systems, Inc; Sure-Seal EPDM: 2. Firestone Building Products, LLC: 3. GenFlex Roofing Systems, LLC: 4. Versico Roofing Systems: 5. Substitutions: See Section Product Requirements. B. Insulation: 1. Atlas Roofing Corporation: 2. GAF: 3. Dow Chemical Co: 4. Owens Corning Corp: 5. Insulation manufactured by the membrane manufacturer is approved ROOFING - UNBALLASTED APPLICATIONS A. Elastomeric Membrane Roofing <EPDM-2>: One ply membrane, mechanically fastened, over insulation. B. Roofing Assembly Requirements: 1. Roof Covering External Fire-Resistance Classification: UL Class A. 2. Factory Mutual Classification: Class I and windstorm resistance of I-75, in accordance with FM DS C. Acceptable Insulation Types - Constant Thickness Application: Any of the types specified. 1. Minimum 2 layers of polyisocyanurate board. D. Acceptable Insulation Types - Tapered Application: Any of the types specified. 1. Tapered polyisocyanurate board ROOFING MEMBRANE AND ASSOCIATED MATERIALS A. Membrane: Ethylene-propylene-diene-terpolymer (EPDM); externally reinforced with fabric; complying with minimum properties of ASTM D Thickness: inch (1.5 mm). 2. Color: Black. 3. Tensile Strength: 1,400 psi (9,652 MPa), measured in accordance with ASTM D Ultimate Elongation: 300 percent, measured in accordance with ASTM D Hardness: 60+10, measured in accordance with ASTM D2240, using Type A durometer. 6. Tear Strength: 150 lbf/in (26.3 kn/m), measured in accordance with ASTM D Water Vapor Permeability: 0.5 perm inch (0.33 ng/(pa s m)), measured in accordance with ASTM E96/E96M. 8. Brittleness Temperature: -60 deg F. (-51 deg C), measured in accordance with ASTM D746. B. Seaming Materials: As recommended by membrane manufacturer. C. Membrane Fasteners: As recommended by and approved by membrane manufacturer. D. Flexible Flashing Material: Same material as membrane; conforming to the following: Edison Elementary Addition - Bid Package
4 2.04 INSULATION 1. Thickness: 60 mil (1.5 mm). 2. Color: Black. A. Polyisocyanurate Board Insulation <INSUL-51>: Rigid cellular foam, complying with ASTM C1289, Type II, Class 1, cellulose felt or glass fiber mat both faces; Grade 2 and with the following characteristics: 1. Compressive Strength: 20 psi (138 kpa) 2. Board Edges: Square ACCESSORIES A. Prefabricated Roofing Expansion Joint Flashing: Sheet butyl over closed-cell foam backing seamed to galvanized steel flanges. B. Stack Boots: Prefabricated flexible boot and collar for pipe stacks through membrane; same material as membrane. C. Cant and Edge Strips: Wood fiberboard, compatible with roofing materials; cants formed to 45 degree angle. D. Insulation Fasteners: Appropriate for purpose intended and approved by roofing manufacturer. E. Membrane Adhesive: As recommended by membrane manufacturer. F. Surface Conditioner for Adhesives: Compatible with membrane and adhesives. G. Thinners and Cleaners: As recommended by adhesive manufacturer, compatible with membrane. H. Sealants: As recommended by membrane manufacturer. I. Walkway Pads: Suitable for maintenance traffic, contrasting color or otherwise visually distinctive from roof membrane. 1. Composition: Roofing membrane manufacturer's standard. 2. Surface Color: As selected by Architect. PART 3 EXECUTION 3.01 EXAMINATION A. Verify that surfaces and site conditions are ready to receive work. B. Verify deck is supported and secure. C. Verify deck is clean and smooth, flat, free of depressions, waves, or projections, properly sloped and suitable for installation of roof system. D. Verify deck surfaces are dry and free of snow or ice. E. Verify that roof openings, curbs, and penetrations through roof are solidly set, and cant strips are in place. Edison Elementary Addition - Bid Package
5 3.02 INSULATION - UNDER MEMBRANE A. Attachment of Insulation: 1. Mechanically fasten first layer of insulation to deck in accordance with roofing manufacturer's instructions and Factory Mutual requirements. B. Lay subsequent layers of insulation with joints staggered minimum 6 inch (150 mm) from joints of preceding layer. C. Place tapered insulation to the required slope pattern in accordance with manufacturer's instructions. D. Lay boards with edges in moderate contact without forcing. Cut insulation to fit neatly to perimeter blocking and around penetrations through roof. E. At roof drains, use factory-tapered boards to slope down to roof drains over a distance of 18 inches (450 mm). F. Do not apply more insulation than can be covered with membrane in same day MEMBRANE APPLICATION A. Roll out membrane, free from wrinkles or tears. Place sheet into place without stretching. B. Shingle joints on sloped substrate in direction of drainage. C. Overlap edges and ends and seal seams by contact adhesive, minimum 3 inches (75 mm). Seal permanently waterproof. Apply uniform bead of sealant to joint edge. D. Mechanical Attachment: Apply membrane and mechanical attachment devices in accordance with manufacturer's instructions. E. At intersections with vertical surfaces: 1. Extend membrane over cant strips and up a minimum of 4 inches (100 mm) onto vertical surfaces. 2. Fully adhere flexible flashing over membrane and up to nailing strips. F. Around roof penetrations, seal flanges and flashings with flexible flashing. G. Install roofing expansion joints where indicated. Make joints watertight. 1. Install prefabricated joint components in accordance with manufacturer's instructions. H. Coordinate installation of roof drains and sumps and related flashings CLEANING A. Remove bituminous markings from finished surfaces. B. In areas where finished surfaces are soiled by work of this section, consult manufacturer of surfaces for cleaning advice and conform to their documented instructions. C. Repair or replace defaced or damaged finishes caused by work of this section PROTECTION A. Protect installed roofing and flashings from construction operations. Edison Elementary Addition - Bid Package
6 B. Where traffic must continue over finished roof membrane, protect surfaces using durable materials. END OF SECTION Edison Elementary Addition - Bid Package
SECTION THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 075423 - THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including Division 00 Bidding Requirements and other Division
More informationSECTION 07530CP EPDM MEMBRANE ROOFING
PART 1 GENERAL 1.1 SUMMARY SECTION 07530CP EPDM MEMBRANE ROOFING A. Section includes: 1. Adhered membrane roofing and flashing 2. Mechanically fastened roof insulation 3. Walkway pads 1.2 ARCHITECTURAL
More informationACADEMIC SUCCESS CENTER THE COLLEGE AT BROCKPORT STATE UNIVERSITY OF NEW YORK PROJECT NO
SECTION 07 53 23 - ETHYLENE-PROPYLENE-DIENE-MONOMER (EPDM) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions ofthe Contract, including General and Supplementary Conditions
More informationSECTION MANUFACTURED ROOF EXPANSION JOINTS
SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 07 5323 - ETHYLENE-PROPYLENE-DIENE-MONOMER (EPDM) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationLouis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1
Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More information1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards
SECTION 07185 TRAFFIC MEMBRANE PART 1 GENERAL 1.1 SECTION INCLUDES A. Traffic membrane, consisting of welded seam PVC waterproofing, over f following surfaces: 1. Decks, balconies, and sun porches 2. Walkways,
More informationHALIFAX HUMANE SOCIETY BOARDING AND GROOMING FACILITY SECTION STYRENE-BUTADIENE-STYRENE (SBS) MODIFIED BITUMINOUS
SECTION 075216 - PART 1 - GENERAL 1.1 SUMMARY A. Section includes styrene-butadiene-styrene (SBS) modified bituminous membrane roofing. 1.2 DEFINITIONS A. Hot Roofing Asphalt: Roofing asphalt heated to
More informationACFoam-II HCFC Free "Green" Polyiso Specification
ACFoam-II HCFC Free "Green" Polyiso Specification To help owners and specifiers, the following specification strategies are offered as they relate to product performance when including HCFC FREE Green
More informationE. Section Polymer Modified Cement Waterproofing. K. Section Sub drainage: Foundation perimeter drainage.
DELTA -DRAIN Section 07 10 00 Dampproofing and Waterproofing PART 1 GENERAL 1.1 SECTION INCLUDES A. Below grade drainage sheets. B. Plaza deck and planter drainage sheets. 1.2 RELATED SECTIONS A. Section
More informationSECTION MODIFIED BITUMINOUS SHEET WATERPROOFING
SECTION 07 13 52 MODIFIED BITUMINOUS SHEET WATERPROOFING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section
More informationSECTION CLAY BARREL TILE ROOFING. A. American Society for Testing and Materials (ASTM):
SECTION 07320 CLAY BARREL TILE ROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 02072 - Removals. 2. 07600 - Flashing and Sheet Metal. 1.02 REFERENCES A. American Society for Testing and Materials
More informationA. Submit product data sheets and literature verifying physical properties of materials.
I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving EPDM Roofs 07500 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide labor,
More informationRoof Replacement. Notes: T-1 (Title Sheet) Roof Key Plan Russell House Student Union 1400 Greene Street Columbia, South Carolina 29208
Notes: Drawing Index T-1 Title R-1 Roof Plan - Existing Conditions R-2 Roof Plan - New D-1 Roof Details D-2 Roof Details D-3 Roof Details M-1 Mechanical - Roof Plan M-2 Mechanical - Details Roof Key Plan
More informationSECTION CO-POLYMER ELASTOMERIC COOL-ROOF COATING
SECTION 076000 - CO-POLYMER ELASTOMERIC COOL- PART 1 - GENERAL 1.1 SUMMARY OF WORK A. Contractor is to supply the necessary labor, materials, and equipment to coat existing roof system (approximately 390
More informationCITY OF RICHMOND PINE CAMP COMMUNITY CENTER ROOF REPLACEMENT PROJECT RCS PROJECT NO
SECTION 07220 - ROOF INSULATION PART 1 - GENERAL 1.01 DESCRIPTION A. Work included: The Roofing Contractor will provide all polyisocyanurate insulation and high density wood fiber roof insulation (tapered
More informationLight-Metal Roof Edge, Raised
NAIL WOOD CANT TO BLOCKING 2 ROWS STAGGERED EACH ROW 24 O.C. 1/2 MIN. 10 0 MAX. FASTEN 18 O.C. WITH NEOPRENE GASKETED FASTENERS 3-1/2 MIN. 4 6 JOINT COVER PLATE SET IN TWO BEADS OF SEALANT 4 MIN. SPECIFIED
More information1.1 SECTION INCLUDES Verify Scope, including identification of plies and type of coating.
SECTION 07 51 00 - BUILT-UP ASPHALT ROOFING PART 1: GENERAL Requestor Note: Requestor to verify project requirements related to roof deck, drainage, fire resistance, wind uplift, insulation, surfacing,
More informationSECTION CLAY BARREL TILE ROOFING Removals Flashing and Sheet Metal.
SECTION 07320 CLAY BARREL TILE ROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 02072 - Removals. 2. 07600 - Flashing and Sheet Metal. 1.02 REFERENCES A. American Society for Testing and Materials
More information1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels. 3. Insulation. 4. Plaza deck pavers.
SECTION 071413 HOT FLUID APPLIED RUBBERIZED ASPHALT WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels.
More informationMEMBRANE ROOFING Christ on the Mountain
SECTION 075000 MEMBRANE ROOFING PART 1 - GENERAL 1.1 SUMMARY A. This Specification Section has been written around Firestone product technology. All other approved manufacturers shall use the same quality
More informationSECTION PREPARATION FOR RE-ROOFING
SECTION 07 01 50.19 PREPARATION FOR RE-ROOFING SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Edit Summary article below after establishing
More informationFirestone Polyiso Boards
Firestone Polyiso Boards Superior energy efficiency. Superior protection. Firestone Polyiso Boards POLISOBROUK10.indd 1 1/04/10 14:26 Firestone Polyiso Boards Firestone total roofing systems Since Firestone
More informationSCOPE OF WORK PROJECT IDENTIFICATION
PROJECT IDENTIFICATION SCOPE OF WORK PROJECT NAME: Wickenburg High School PROJECT: Gym Roof 1 SITE ADDRESS: 1090 S. Vulture Mine Rd. Wickenburg AZ 85390 City State ZIP Code SCOPE OF WORK SUMMARY: 1. Extend
More information(Project Location) (your firm's name)
SECTION 07 21 00 THERMAL INSULATION PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the Conditions of the Contract and Division 01 Specification Sections
More informationFOAMULAR Commercial Roofing
Low Slope Insulated Roof Systems Roofing Systems Single-ply roofing s are flexible sheets of compounded synthetic materials that are manufactured in a factory. Single ply roof systems provide strength,
More informationSECTION mil thickness COLD FLUID-APPLIED WATERPROOFING
SECTION 07 14 16 CCW-MIRASEAL @ 120 mil thickness COLD FLUID-APPLIED WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Installation of waterproofing membrane on surfaces indicated on drawings, consisting
More informationMaster Guide Specification Page 1
Master Guide Specification Page 1 SPEC NOTE: This guide specification is intended for use when specifying the restoration of an existing built-up asphalt membrane roof. Make any required selections, such
More informationDESIGN GUIDELINE FLUID-APPLIED WATERPROOFING
DESIGN GUIDELINE FLUID-APPLIED WATERPROOFING (TO RESTORE EPDM MEMBRANES) PART 1 GENERAL 1.01 DESCRIPTION A. The scope of this design guideline is to describe the installation of the ALDOCOAT Silicone reflective
More informationSECTION PRE-ENGINEERED BUILDING INSULATION
PART 1 GENERAL SECTION 07213 PRE-ENGINEERED BUILDING INSULATION Microsoft Word Instructions: Display hidden notes to specifier by using "Tools"/"Options"/"View"/"Hidden Text". 1.1 SECTION INCLUDES A. Pre-Engineered
More informationSECTION ROOF SPECIALTIES
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 07 71 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION TURBINE VENTILATORS
SECTION 07 72 00 TURBINE VENTILATORS **This is a CSI Three-Part Specification using CSI MasterFormat 2004-2010 Section Numbers and Titles. This specification must be edited to suit your particular project.
More informationApplication Specification:
Application Specification: GW-15-UBU-HD April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR VEHICULAR TRAFFIC DECKS AND RAMPS
More informationSECTION METAL ROOF PANELS
SECTION 07 41 13 PART 1 GENERAL 1.1 SECTION INCLUDES A. Standing-seam roof panels. B. Metal roofing accessories. 1.2 RELATED SECTIONS A. Section 07 62 00 - Sheet Metal Flashing. B. Section 07 72 00 - Roof
More informationRUBBERGARD EPDM SA APPLICATION GUIDE
RUBBERGARD EPDM SA APPLICATION GUIDE I. MEMBRANE APPLICATION... 2 A. MEMBRANE... 2 II. MEMBRANE ATTACHMENT... 2 A. MEMBRANE PREPARATION... 2 B. MEMBRANE APPLICATION... 2 III. SEAMING... 3 VI. MEMBRANE
More informationGuideline Specification ACRYMAX ARS-1-C Reinforced Composite Elastomeric Membrane System for Concrete Roofs Fluid-Applied Roofing
221 Brooke Street Media, PA 19063 610-566-7470 Fax 610-891-0834 Website www.acrymax.com e-mail info@acrymax.com This document is intended to provide guidelines for the proper specification and application
More information1. Project Location: Phase II Roof Troughs and Aluminum Gutters at the Morial Convention Center.
SECTION 01 11 00 SUMMARY OF WORK PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 Specification
More informationROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART GENERAL 1.
07555 - ROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART 1.00 - GENERAL 1.01 SUMMARY: A. The work of this section consists of furnishing and installing
More informationB. American Society for Testing and Materials: 1. ASTM F708 - Standard Practice for Design and Installation of Rigid Pipe Hangers.
SECTION 230529 - HANGERS AND SUPPORTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Sleeves. 6. Mechanical sleeve seals. 7. Firestopping
More informationARCHITECTURAL GUIDE SPECIFICATION REROOFING OVER EXISTING BUR C-EPDM SYSTEM 2001 FOR STEEL AND WOOD DECKS
ARCHITECTURAL GUIDE SPECIFICATION REROOFING OVER EXISTING BUR C-EPDM SYSTEM 2001 FOR STEEL AND WOOD DECKS RESTRICTIONS - This specification is not applicable for 1) roof slopes in excess of one (1) inch
More informationSECTION STYRENE-BUTADIENE-STYRENE (SBS) MODIFIED BITUMINOUS MEMBRANE ROOFING
SECTION 075216 - STYRENE-BUTADIENE-STYRENE (SBS) MODIFIED BITUMINOUS MEMBRANE ROOFING PART 1 - GENERAL 1.1 SUMMARY A. Section includes styrene-butadiene-styrene (SBS) modified bituminous membrane roofing.
More informationDesign and Construction Standards. Division 07 Thermal and Moisture Protection
Division 07 Thermal and Moisture Protection General In general, follow the guidelines below when designing, specifying and installing roofing, waterproofing, exterior siding, insulation, fire stopping
More informationAPPLICATION SAFETY TOOLS REQUIRED
Revised April 2007 Product Technical Bulletin SFM-3.5H-FR BITUMEN-POLYMER WATERPROOFING MEMBRANE, MADE FROM SELECT SBS AND DISTILLED BITUMEN, REINFORCED WITH HIGH-STRENGTH FIBERGLASS MAT UL CLASS A FIRE-RATED
More informationASSEMBLY DESIGN CRITERIA
Issue: 01 Revision: 00 Page 1 of 7 1 ASSEMBLY - GENERAL 1.1 The work of this section includes the provision of all design, labour, materials, equipment and services required to fabricate and install roof
More informationSECTION SELF-ADHERING SHEET WATERPROOFING
SECTION 07 13 26 SELF-ADHERING SHEET WATERPROOFING This guide specification has been prepared by Polyguard Products Inc., in printed and electronic media, as an aid to specifiers in preparing written construction
More informationERSYSTEM ONESTEP PLUS
1 DG0047-A 05/2017 AGED (EPDM, TPO, CSPE-HYPALON, PIB) SINGLE-PLY (THERMOSET) MEMBRANE RESTORATION SYSTEM APPLICATION SAMPLE DESIGN GUIDELINE ERSYSTEM ONESTEP PLUS ITW POLYMERS SEALANTS NORTH AMERICA,
More informationFloor Insulation Underlayment Section Sound Control Matting
Floor Insulation Underlayment Section 09618 Sound Control Matting Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in excess of 50 to meet building
More informationTOPCOAT Restoration Specifications Structural Concrete
TOPCOAT Restoration Specifications Structural Concrete Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications Structural Concrete
More informationSECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM
PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.
More informationFOAMULAR Insulation, PRMA, Horizontal Waterproofing
PROJECT ENGINEER RESPONSIBILITY: This is a general specification guide, intended to be used by experienced construction professionals, in conjunction with good construction practice and professional judgment.
More informationSECTION ALPHAGUARD RESTORATION 20 YEAR WARRANTY SYSTEM. f. Conditions and Division 01 Specification Sections, apply to this Section.
SECTION 07015 ALPHAGUARD RESTORATION 20 YEAR WARRANTY SYSTEM PART I.1 GENERAL A. RELATED DOCUMENTS 1. The attached are components of this section: a. General Conditions b. Supplemental Conditions c. Statement
More informationSECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION
SECTION 093000 - SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing, vapor retarder, and crack isolation in conjunction
More informationENKASONIC FLOOR UNDERLAYMENT 9110
ENKASONIC FLOOR UNDERLAYMENT 9110 GS1197 Section 13080 SECTION 09618 SOUND CONTROL MATTING Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in
More informationMULE-HIDE PRODUCTS CO., INC. MULE-HIDE SELF-ADHERING TPO ROOFING SYSTEM
MULE-HIDE PRODUCTS CO., INC. MULE-HIDE SELF-ADHERING TPO ROOFING SYSTEM 07500/MUL PART 1 - GENERAL 1.01 Description A. Scope: 1. Thermoplastic Self Adhering Single Ply Roofing 2. Insulation B. Related
More informationCS-100 Guide Specifications
MANUFACTURER CUSTOM-BILT METALS 1333 Corporate Drive, Suite 103 Irving, Texas 75038-2520 (800) 826-7813 or info@custombiltmetals.com www.custombiltmetals.com CS-100 Guide Specifications This Guide Specification
More informationSECTION PVC SINGLE PLY ROOFING
SECTION 07 54 23 PVC SINGLE PLY ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Attached GENERAL CONDITIONS, GENERAL NOTES, INSTRUCTIONS TO BIDDERS, AND BID FORM are components of this section. B. Section
More informationUL Evaluation Report UL ER Issued: December 19, 2014 Revised: August 14, UL Category Code: ULFB. CSI MasterFormat
UL Evaluation Report UL ER9516-02 Issued: December 19, 2014 Revised: August 14, 2015 Visit UL s On-Line Certifications Directory: www.ul.com/erdirectory for current status of Report. UL Category Code:
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationGE SCM3500 High Solids Silicone Roof Coating
GE SCM3500 High Solids Silicone Roof Coating Installation Guide Specification For GRANULATED or SMOOTH MODIFIED BITUMEN / BUR (20 Year Warranty) Warranty PART 1 GENERAL 1.01 SUMMARY A. This specification
More informationROXUL Roof and Deck Insulation Section Master Guide Specification Page 1 April 2016
Master Guide Specification Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROXUL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual. 1 GENERAL
More informationSUBMITTALS Descriptive literature: Submit manufacturer's application instructions and technical data sheets or catalog cuts on materials.
PART I GENERAL APPLICABLE PUBLICATIONS The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by the basic designation only.
More informationProduct Technical Bulletin APS-5T
Revised April 2007 Product Technical Bulletin APS-5T BITUMEN-POLYMER WATERPROOFING MEMBRANE, MADE FROM SELECT APP AND DISTILLED BITUMEN, REINFORCED WITH SPUNBOND POLYESTER FABRIC. BITEC APS-5T is a torch
More information1. Clean the existing totally adhered or mechanically attached roof membrane: TPO, EPDM, Hyplon,
Summary Specification Re-Skinning Over Two Existing Roofs The Top Roof Being a Totally Adhered Single Ply Over a Built-Up-Roof On A Poured-in-Place Concrete Deck Using the Existing Angle Change Terminations
More informationMetal Roof Panels
University of New Hampshire University of New Hampshire Scholars' Repository Division 07 Thermal and Moisture Protection Chapter 5 Technical Construction and Renovation Standards 1-25-2013 074113 - Metal
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationGenFlex EZ TPO Peel & Stick SA (HW) APPLICATION GUIDE
GenFlex EZ TPO Peel & Stick SA (HW) APPLICATION GUIDE I. MEMBRANE APPLICATION... 2 A. MEMBRANE... 2 II. MEMBRANE ATTACHMENT... 2 III. SEAMING... 3 A. SEAMING FOR GENFLEX EZ TPO PEEL & STICK SA (HW)...
More informationPERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960
STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary
More informationSAM HOUSTON STATE UNIVERSITY DIVISION 07 THERMAL & MOISTURE PROTECTION SECTION ROOFING SYSTEMS DESIGN AND CONSTRUCTION STANDARDS February 2016
PART 1: GENERAL 1.01 Scope Of Standard 1.02 Reference Standards 1.03 Quality Control A. This standard provides general guidance concerning the specific preferences of the Sam Houston State University for
More information.1 Provide submittals in accordance with Section Submittal Procedures.
Place D Orléans Transitway Section 07 13 52 1231 Place D Orléans Dr, Ottawa, ON. WATERPROOFING MEMBRANE City of Ottawa Project No. CR008042 Page 1 of 2 1 GENERAL 1.01 SUBMITTALS.1 Provide submittals in
More informationSPECIFICATION GUIDELINE
Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section
More informationA. Source Limitations: Obtain each type of building insulation through one source.
SECTION 07210 - BUILDING INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationLEGACY REPORT DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FLUID APPLIED ROOFING REPORT HOLDER: CONKLIN COMPANY INC.
0 Most Widely Accepted and Trusted ICC ES Legacy Report ICC ES 000 (800) 42 6587 (562) 699 054 www.icc es.org ER 520 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 07 00 00 THERMAL
More informationSECTION EPDM MEMBRANE WATERPROOFING
SECTION 07115 EPDM MEMBRANE WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Furnish and install Sure-Seal EPDM Membrane Waterproofing System for vertical and horizontal applications on concrete block,
More informationTTR SYSTEMS ROOF SPECIFICATION
SECTION 07 53 24 EPDM roofing membrane applied over spray applied polyurethane foam TTR SYSTEMS ROOF SPECIFICATION This specification has been numbered, organized and formatted in accordance with the Master
More informationPG 9600 HIGH SOLIDS SILICONE ROOF COATING
WARRANTY INSTALLATION GUIDE SPECIFICATION FOR RESTORATION OF EXISTING SINGLE-PLY ROOFS (20 YEAR WARRANTY) PART 1 GENERAL 1.01 SUMMARY A. PG 9600, manufactured by ProGuard Group, Inc., is a high solids,
More informationJ41 Reinforced bitumen membrane roof coverings
J41 Reinforced bitumen membrane roof coverings To be read with Preliminaries/General conditions. A comprehensive waterproofing system comprising two reinforced bituminous membranes fully adhered to thermal
More informationEXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,
More informationLAKEWOOD HIGH SCHOOL RECOAT/REROOF PROJECT 100% OWNER REVIEW
SECTION 07106-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
More informationA. Manufacturer: A firm that produces primary glass or fabricated glass as defined in referenced glazing publications.
SECTION 08800 - GLAZING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationREPORT HOLDER: CARLISLE SYNTEC POST OFFICE BOX 7000 CARLISLE, PENNSYLVANIA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1184 Reissued 03/2017 This report is subject to renewal 03/2019. DIVISION: 07 00 00 THERMAL
More informationColphene BSW Training and Application Guide. Colphene BSW Waterproofing Membrane. 1. Prepare substrate
Colphene BSW Training and Application Guide Colphene BSW Waterproofing Membrane. 1. Prepare substrate Substrate must be structurally sound. Surface must be free of voids, spalled areas, loose aggregate,
More informationTOPCOAT System Specifications Corrugated Transite Panels
TOPCOAT System Specifications Corrugated Transite Panels Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT System Specifications Corrugated Transite
More informationCorium Brick Rainscreen System Specifications
CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated
More informationSECTION ATHLETIC AND RECREATIONAL SURFACING. A. ASTM C 67 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile.
SECTION 02790 ATHLETIC AND RECREATIONAL SURFACING PART 1 GENERAL 1.1 SECTION INCLUDES A. Resilient interlocking fitness flooring. 1.2 RELATED SECTIONS 1.3 REFERENCES A. ASTM C 67 - Standard Test Methods
More informationA. Deliver material to job site in original, nonbroken, factory packaging, labeled with manufacturer's density and thickness.
SECTION 15250 PIPING AND EQUIPMENT INSULATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract including General and Supplementary Conditions, Division 1 Specification
More information1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationConstruction. S-Vap 5000E SA Self-adhesive Vapour Barrier. Product Description
Roofing Product Data Sheet Edition 11.2014 / xtra UK Identification no. 02 09 45 05 100 0 000019 Version no. 03 S-Vap 5000E SA Self-adhesive Vapour Barrier Product Description S-Vap 5000E SA is a multi-layer
More informationA. Product Data: Submit manufacturer s product data, with complete general and specific installation instructions, recommendations, and limitations.
SECTION 071700 - BENTONITE WATERPROOFING PART 1 - GENERAL 1.1 WORK SUMMARY A. The work of this section includes, but is not limited to the furnishing and installing the following materials, per project
More informationROXUL Roof and Deck Insulation Section Master Guide Specification (MONOBOARD ) Page 1 April 2016
Master Guide Specification (MONOBOARD ) Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROXUL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual.
More information1.2 DEFINITIONS, REFERENCES, AND OVERALL STANDARDS Follow 07500
07721 ROOF ASSEMBLY SUPPORTS FOR ROOFTOP EQUIPMENT ****************************************** SPECIFIER: All roof-related items above or outside the structural roof deck, including such work as blocking,
More informationFIRESTONE ULTRAPLY TPO SA APPLICATION GUIDE
FIRESTONE ULTRAPLY TPO SA APPLICATION GUIDE I. MEMBRANE APPLICATION... 2 A. MEMBRANE... 2 II. MEMBRANE ATTACHMENT... 2 III. SEAMING... 3 A. SEAMING FOR FIRESTONE ULTRAPLY TPO SA... 3 B. T-JOINT AREAS...
More informationProduct Technical Bulletin SPM-4H-250
Revised April 2007 Product Technical Bulletin SPM-4H-250 BITUMEN-POLYMER WATERPROOFING MEMBRANE, MADE FROM SELECT SBS AND DISTILLED BITUMEN, REINFORCED WITH SPUNBOND POLYESTER FABRIC. BITEC SPM-4H-250
More informationTEKTON Flashings and TEKTON Construction Tape
TEKTON Flashings and TEKTON Construction Tape Complete the system with TEKTON Flashings and Construction Tape. It is important to assure a tight building envelope when windows and siding are installed.
More informationIPE WOOD DECK TILES National Distribution SPEC - SECTION 07760
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationAlply CLASSIC WALL Architectural Insulated Panel Wall System
SECTION 07 42 13 INSULATED METAL WALL PANELS ALPLY Insulated Panels Alply CLASSIC WALL Architectural Insulated Panel Wall System PART 1 / GENERAL 1.1 SYSTEM DESCRIPTION A. Smooth, non-embossed steel, insulated
More informationSECTION COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING
P.O. Box 599 - Mars, PA 16046 800-321-3337 SECTION 07555 COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including
More informationA. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section.
SECTION 070150.76 REHABILITATION OF SINGLE PLY MEMBRANES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply
More informationSECTION REFLECTIVE-FACED, MASONRY CAVITY WALL INSULATION
MANUFACTURER S GUIDE SPECIFICATIONS SECTION 04 27 23 REFLECTIVE-FACED, MASONRY CAVITY WALL INSULATION 900 Hensley Lane Wylie TX 75098 800-527-7092 www.carlisleccw.com 07.09.13 Carlisle and R2+ are trademarks
More informationDSC BUILDING 1200 ALTERATIONS OCTOBER 2011 SECTION DUCT INSULATION
SECTION 230713 DUCT INSULATION PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 233113 Ductwork and Accessories 1.2 REFERENCES A. American Society for Testing and Materials (ASTM): 1. E84-96a Test Method
More information