Bondstrand Series 3000 Fiberglass Pipe for General Industrial Service

Transcription

1 Bondstrand Series 3000 Fiberglass Pipe for General Industrial Service Uses and Applications Boiler feed water Bridge, roof and floor drains Brine and brackish water Chemical process piping Cooling water Demineralized water Electroplating Fuel oil piping General service piping Mild chemicals Municipal waste Oilfield gathering, transmission lines Power plant, steel mill and industrial plant piping Sewer lines and sewer force mains Source and recycle water Sump discharge Vent lines Water mains Water treatment Performance Working pressure to 450 psig depending on pipe size. Operating surge pressure to 1.25 times rated operating pressure. No thrust blocks are required at rated system pressure for most buried piping configurations and most soil conditions. Temperatures to 150 F (66 C) maximum. Full vacuum capabilities when buried and properly backfilled. For above ground use, refer to collapse pressures listed below under pipe pressure performance. Recommended burial depth: 3 to 25 feet. Recommended for water, waste water (ph 1 to 8.5), moderately corrosive liquids and mild chemicals. Consult corrosion guide or Applications Engineering for recommendations for your particular application. Individual system components may not have the same ratings as the pipe. Refer to the detailed product information for the specific components to determine the pressure rating for the system as a whole. Composition Pipe Filament-wound fiberglass reinforced epoxy pipe with integral epoxy liner and exterior coating. ASTM Designation in mm D2310 D RTRP 11FX RTRP 11FX RTRP 11FW RTRP 11FW fgspipe@nov.com

2 Fittings 2 to 6 inch Compression-molded fiberglass reinforced epoxy elbows and tees Filament-wound and/or mitered crosses, wyes, laterals and reducers 8 to 16 inch Filament-wound fiberglass reinforced epoxy elbows Filament-wound and/or mitered crosses, wyes, and laterals Contact-molded reducers Flanges Flange rings: Molded or filament-wound fiberglass Stub ends: Molded or centrifugally cast fiberglass Blind flanges Compression-molded fiberglass or epoxy-coated cast iron or steel. Adhesive Two-part epoxy adhesive for field fabrication. (Consult NOV Fiber Glass Systems for specifications.) Joining Systems 2 to 16 inch Bell and spigot taper/taper adhesive-bonded joint. Pipe Lengths Standard 20 and 39 ft. random lengths. Other lengths available on request. 2

3 Typical Pipe Dimensions and Weights Outside Diameter Inside Diameter Total Wall Thickness Structural in mm in mm in mm in mm in mm Typical outside diameters of 2 through 12 inch pipe are within API, ASTM and ANSI fiberglass and steel pipe dimensions. Taper Angle Taper Length Pipe Weight in mm deg in mm lb/ft kg/m Typical Pipe Performance Static Pressure Rating at 150 F Ultimate Ultimate Collapse Pressure (2) Internal Pressure 80 F 27 C 150 F 99 C in mm psig bar psig bar psig bar psig bar , , , , Quality Control minimum (2) For vacuum service above ground in sizes 10 inches and above consult NOV Fiber Glass Systems. 3

4 Fittings Pressure Ratings (3) Elbows Tees Flanges (2) Blind Flanges in mm psig bar psig bar psig bar psig bar Adapters Laterals, Wyes and Crosses Saddles in mm psig bar psig bar psig bar Ratings shown are for 90 and 45 elbows. Ratings in 8 to 16 inch sizes are also applicable to elbows of other angles. (2) ANSI B16.5 CL150 psig bolt hole pattern (3) Ratings at 150 F Typical Physical Properties Pipe Property Units Value ASTM Thermal conductivity Btu-in/(h ft 2 F ) W/m C C177 Coefficient of thermal expansion (linear) (77 F to 210 F) (25 C to 65 C) 10-6 in/in/ F 10-6 cm/cm/ C 8.5 to to 21.6 D696 E228 Flow coefficient Hazen-Williams Absolute roughness 10-6 ft 10-6 m Specific gravity 1.81 D792 4

5 Typical Mechanical Properties Tensile strength Longitudinal Circumferential Tensile modulus Longitudinal Circumferential Pipe Property Compressive strength Longitudinal Compressive modulus Longitudinal Long-Term Hydrostatic Design Basis (3) Static, Hoop Stress 95% LCL 20-year F/65 C Cyclic, Hoop Stress 95% LCL 20-year F/24 C Units 10 6 psi GPa 10 6 psi GPa 10 6 psi GPa Poisson s Ratio (2) ν yx ν xy Based on structural wall thickness, at room temperature unless noted. Value 2-6 in 8-16 in ASTM D2105 D1599 D2105 D2992 Procedure B D2992 Procedure A (2) The first subscript denotes the direction of applied stress and the second subscript the measured strain contraction. x denotes longitudinal direction. y denotes circumferential direction. (3) Test fixtures were end type (full end thrust on samples). Change in Length Due to Pressure Stiffness Factor (2) in mm in/100 ft/100 psi mm/10m/10 bar lb in 3 /in 2 N m , , , In an unrestrained system due to pressure effects alone. (2) At 5% deflection. 5

6 Support Spacing (Values are based on a ½ inch (12 mm) deflection at mid span.) (4) Single Span Continuous Span (2) Gases 1.00 (3) 1.3 (3) Gases (3) in mm ft m ft m ft m ft m ft m ft m For fluid temperatures above 77 F (25 C) reduce span lengths 0.1-inch/ F (5 mm/ C) (2) Beam fixed at both ends and uniformly distributed loads. Intermediate spans may be calculate by multiplying the single span length by 1.2. (3) Fluid specific gravity. Bending Radius Minimum Bending Radius Maximum Deflection per 39-ft Joint At rated pressure. Sharper bends may create excessive stress concentrations. Do not bend pipe until adhesive has cured. Minimum Length Required for 10 Change in mm ft m deg ft m

7 Guide Specification Pipe Construction PipeThe structural wall of fiberglass pipe in 2 through 16 inch nominal pipe sizes shall be constructed of continuous glass fibers wound in a matrix of anhydride cured epoxy resin in a dual angle pattern that takes optimum advantage of the tensile strength of the filaments. Pipe produced by filament-winding shall have a smooth outer surface with an outside diametral tolerance not exceeding ±1.0%. The pipe shall incorporate an integral liner with a nominal thickness of ± inches for 2 through 16 inch nominal sizes. The pipe shall be manufactured in accordance with ASTM Standard D2996 for filament-wound reinforced thermosetting resin pipe (RTRP). When classified under ASTM Standard D2310, the pipe shall be Type 1, Grade 1, and Class F for 2 through 16 inch nominal pipe sizes. Pipe shall be provided in standard lengths up to 40 feet, and shall be available in 60 ft. lengths on special request to minimize the number of field joints for rapid installation. Pressure ratingpipe in 2 through 16 inch sizes shall be rated for a minimum internal pressure of 150 psig at 150 F. Fittings Construction Fittings in 8 through 16 inch nominal sizes shall be filament wound and incorporate a resin-rich liner of equal or greater thickness than the pipe liner and shall be constructed of the same glass and resin type for corrosion and abrasion resistance equal to that of the pipe. Fittings in 2 through 6 inch nominal sizes may be compression molded from glass and resins similar to those used in the pipe. Sprayed-up fittings shall not be permitted. Pipe and fittings shall be joined using bell and spigot taper/taper adhesive-bonded joints or mechanical screw-on type joints. Physical and Mechanical Requirements Values for physical and mechanical properties shall be no less than 95% of those shown tabulated above under Typical Physical Properties and Typical Mechanical Properties. Workmanship The pipe and fittings shall be free from all defects, including delamination, indentations, pinholes, foreign inclusions, bubbles and resin-starved areas which, due to their nature, degree or extent, detrimentally affect the strength and serviceability of the pipe or fittings. Pigments or dyes may be used in the resin as long as the product is sufficiently translucent to verify the structural integrity of the structural wall. The pipe and fittings shall be as uniform as commercially practicable in color, density and other physical properties. Testing Quality control testingsamples of pipe and fittings shall be tested at random based on standard quality control practices to determine conformance of the materials to the following ASTM guidelines for testing fiberglass pipe products: ASTM D1599, D2105, D2925, D2992A or D2992B. Test samples may be hydrostatically tested by the manufacturer to 1.5 times the pressure rating for signs of leakage. Marking Each component shall be marked to show the following: Manufacturer s name and address pipe size Hydrostatic test pressure (if so ordered) Date and shift of manufacture (pipe only) 7

8 National Oilwell Varco has produced this brochure for general information only, and it is not intended for design purposes. Although every effort has been made to maintain the accuracy and reliability of its contents, National Oilwell Varco in no way assumes responsibility for liability for any loss, damage or injury resulting from the use of information and data herein nor is any warranty expressed or implied. Always cross-reference the bulletin date with the most current version listed at the web site noted in this literature. North America South America Europe Asia Pacific Middle East San Pedro Ave. Suite 200 Estrada de Acesso á Zona P.O. Box 6, 4190 CA No. 7A, Tuas Avenue 3 P.O. Box San Antonio, Texas USA Industrial Portuária de Suape, s/no. Geldermalsen, The Netherlands Jurong, Singapore Dubai, UAE Phone: Recife, PE, Brazil Phone: Phone: Phone: Phone: fgspipe@nov.com 2013, National Oilwell Varco. All rights reserved. CI July 2013