Panel elements. Closed Panels Transparent Panels Non-Transparent Panels Mesh Panels Accessories for Panel Elements

Transcription

1 Panel elements Closed Panels Transparent Panels Non-Transparent Panels Mesh Panels Accessories for Panel Elements

2 Panel elements Products in this section Acrylic Glass Polycarbonate PET-G Sheet Material Al Compound Material Al Available in transparent, tinted and frosted versions Excellent dimensional stability Maximum protection for man and machine Impact-proof and available in clear and tinted versions Transparent and deformation-free Impact-proof and the best optical properties Stable and durable Available in two surface finishes Lightweight and insulating Anodized sheets with a PE core Compound Material St Plastics Chequer Sheet Corrugated Mesh Al Corrugated Mesh St Steel with a white plastic coating, suitable for use with magnets For surfaces and panelling that have to take a lot of punishment Wear resistant and resistant to impacts Also available in ESD-safe version Stable and non-slip For steps and platforms For lightweight guards and enclosures Particularly easy to machine For high-strength fixtures Available in three mesh widths Dual-Rod Mesh Steel Mesh Perforated Sheet Sound-Insulating Material Edge Profile S3 Al Stable even without a frame Two mesh widths available Welded wires ensure exceptional stability Can be inserted directly into the profile groove Stylish and air-permeable Suitable as screening and ventilation covering Create a peaceful environment in offices and production halls For partitions in open-plan offices or as a panel element in hoods and enclosures Attractive finish Covering for sharp cut edges

3 Acrylic Glass Available in transparent, tinted and frosted versions Excellent dimensional stability Cast acrylic glass with scratch-resistant surface is suitable for doors and casings. The panels can be polished to a high gloss. Acrylic Glass XT in extruded quality has slightly lower mechanical and thermal load bearing capabilities and optical characteristics than cast panels. But in many applications, it can represent a cost-effective alternative. Whether double-frosted, tinted, opal-white or glass-look, Acrylic Glass is ideal for use as translucent partitions designed to restrict visibility and for the stylish design of wall and ceiling elements. It exhibits excellent dimensional stability at higher temperatures coupled with good light diffusion and transmission characteristics, which also make it ideal for light boxes and backlit advertising areas. Property Value Test Standard Density 1.19 g/cm 3 ISO 1183 Water absorption 30 mg ISO 62 Tensile strength 82 N/mm² ISO 527 Elongation at tear 5.6 % ISO 527 Modulus of elasticity in tension 3300 N/mm² ISO 527 Impact resistance (without notch) 2 kj/m² ISO 179 Vicat softening temperature 1 C ISO 306 Coefficient of thermal expansion 70 x -6 K -1 DIN Construction material class B 2 DIN 42 Refractive index 1.49 n D 20 ISO 489 Luminous transmission index clear / tinted 93.7% / 41% DIN 5036-T3 Surface resistance 14 Ohm DIN Materials used in all the following products: PMMA Acrylic Glass 4mm XT Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 4.60 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm Acrylic Glass 5mm XT Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 5.75 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm Acrylic Glass 2mm Panel dimensions approx. 3050x2030 mm Thickness tolerance ± % m = 2.30 kg/m 2 clear, cut-off max. 3020x2000 mm clear, 1 pce. panel dimensions. max. 3050x2030 mm

4 Acrylic Glass 5mm Panel dimensions approx. 3050x2030 mm Thickness tolerance ± % m = 5.90 kg/m 2 clear, cut-off max. 3020x2000 mm clear, 1 pce. panel dimensions. max. 3050x2030 mm tinted, cut-off max. 3020x2000 mm tinted, 1 pce. panel dimensions. max. 3050x2030 mm Acrylic Glass 8mm Panel dimensions approx. 3000x2000 mm Thickness tolerance ± % m = 9.44 kg/m 2 clear, cut-off max. 2970x1970 mm clear, 1 pce. panel dimensions. max. 3000x2000 mm tinted, cut-off max. 2970x1970 mm tinted, 1 pce. panel dimensions. max. 3000x2000 mm Acrylic Glass 4mm double-frosted Panel dimensions approx. 3050x2030 mm Thickness tolerance ± % m = 4.60 kg/m 2 opal-white, cut-off max. 3020x2000 mm opal-white, 1 pce. panel dimensions. max. 3050x2030 mm tinted, cut-off max. 3020x2000 mm tinted, 1 pce. panel dimensions. max. 3050x2030 mm glass-look, cut-off max. 3020x2000 mm glass-look, 1 pce. panel dimensions. max. 3050x2030 mm

5 Polycarbonate Maximum protection for man and machine Impact-proof and exceptionally safe Available in clear and tinted versions Polycarbonate is impact resistant and is therefore ideal for use as a panel element for cost-effective enclosures, even in relatively small thicknesses. Its high strength and transparency mean that the material is particularly suitable for applications where it is important both to be able to monitor processes and yet provide adequate protection for personnel. Property Value Test Standard Density 1.2 g/cm 3 ISO 1183 Water absorption 8 mg ISO 62 Tensile strength 60 N/mm² ISO 527 Elongation at tear 80 % ISO 527 Modulus of elasticity in tension 2200 N/mm² ISO 527 Impact resistance (without notch) doesn t break ISO 179 Vicat softening temperature 145 C ISO 306 Coefficient of thermal expansion 65 x -6 K -1 DIN Construction material class B 2 DIN 42 Refractive index n D 20 ISO 489 Luminous transmission index clear / tinted 86% / 51% DIN 5036-T3 Surface resistance 14 Ohm DIN Materials used in all the following products: PC Polycarbonate 2mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 2.40 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm Polycarbonate 4mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 4.80 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm Polycarbonate 5mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 6.00 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm tinted, cut-off max. 3020x2020 mm tinted, 1 pce. panel dimensions. max. 3050x2050 mm

6 Polycarbonate 8mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 5% m = 9.60 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm tinted, cut-off max. 3020x2020 mm tinted, 1 pce. panel dimensions. max. 3050x2050 mm

7 PET-G Transparent and free from distortion Best optical properties Impact-proof Resistant to chemicals PET-G (glycol-modified polyethylene terephthalate) is an impact-resistant, clear plastic used for constructing machine casings, protective housings and partitions, and is suitable for both indoor and outdoor use. This highly transparent material exhibits a far higher resistance to impact than acrylic glass and is also easier to work with. It displays better optical characteristics than polycarbonates and is more resistant to chemicals. Property Value Test standard Density 1.27 g/cm 3 D 1505 Tensile strength 50 N/mm² DIN Elongation at tear 54 % DIN Modulus of elasticity in tension 2200 N/mm² DIN Impact resistance (without notch) doesn t break DIN Vicat softening temperature 82 C DIN Coefficient of thermal expansion 6.8 x -5 K -1 DIN Construction material class B 1 DIN 42 Refractive index 1.57 n D 20 DIN Luminous transmission index clear / tinted 88% DIN 5036 Surface resistance 16 Ohm D 257 Materials used in all the following products: PET PET-G 4mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 4% m = 5.13 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm PET-G 5mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 4% m = 6.40 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm PET-G 6mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 4% m = 7.70 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm PET-G 7mm Panel dimensions approx. 3050x2050 mm Thickness tolerance ± 4% m = 8.98 kg/m 2 clear, cut-off max. 3020x2020 mm clear, 1 pce. panel dimensions. max. 3050x2050 mm

8 Sheet Material Al Stable and durable Available in two surface finishes Sheet Material Al is suitable for machine casings of all types. Property Value Density 2.7 g/cm 3 Modulus of elasticity 70,000 N/mm² Tensile strength 120 N/mm² Ductile yield A5 5 % Anodized natural E6/EV1 Min. layer thickness μm Layer hardness HV Sheet Material Al 2mm AlMg1 Panel dimensions approx. 3000x1500 mm m = 5.40 kg/m 2 cold rolled (not degreased), cut-off max. 2970x1470 mm cold rolled (not degreased), 1 pce. panel dimensions. max. 3000x1500 mm natural anodized, cut-off max. 2970x1470 mm natural anodized, 1 pce. panel dimensions. max. 3000x1500 mm Compound Material Al Lightweight and insulating Compound Material Al consists of two anodized aluminium outer layers which are permanently bonded together by a PE core. It is ideal for lightweight doors and panelling. Property Value Tensile strength R m > 130 N/mm² 0.2 limit R p0.2 > 90 N/mm² Ductile yield > 8 % Modulus of elasticity E 70,000 N/mm² Flexural strength 53 N/mm² Temperature resistance - 50 C to + 80 C Coefficient of thermal expansion 23x -6 K -1 Construction material class in accordance with DIN 42 B2 302

9 Compound Material Al 4mm Al-PE compound Panel dimensions approx. 3000x1500 mm m = 5.80 kg/m 2 natural anodized, cut-off max. 2960x1470 mm natural anodized, 1 pce. panel dimensions. max. 3000x1500 mm Compound Material St With white plastic coating With easy-clean surface that can be written on Suitable for use with magnets Besides being magnetic, the surface of the Compound Material can also be directly written on. Compound Material St 2 mm comprises 5 layers and is suitable for use with magnets and whiteboard markers. You can also use the Compound Material as a base for the magnetic Notice Holders or for pinning up notices with magnets. Available as a panel or a cut-off in the dimensions of your choice. Property Value Tensile strength R m > 800 N/mm² Ductile yield > 30 % Modulus of elasticity E 400,000 N/mm² Temperature resistance 0 C Compound Material St 2 mm St-PE compound m = 6.87 kg/m 2 white similar to RA L 9016, cut-off max. 3020x1190 mm white similar to RA L 9016, 1 pce. panel dimensions. max. 3050x1220 mm

10 Plastics For surfaces and panelling that have to take a lot of punishment Wear resistant and resistant to impacts Antistatic surface Available in several colours Plastic is a thermosetting material which is permanently laminated at high pressure and temperature. This gives it exceptional abrasion and impact resistance, making it suitable for panelling, table surfaces and partitions subject to high stresses. It has antistatic. Thanks to their hygienic melamine resin surface, Plastic panels have exceptional mechanical properties and high temperature resistance and are also particularly resistant to a large number of chemicals. Consequently, they can be used where substances such as laboratory and industrial chemicals solvents disinfectants colouring agents bleaching agents industrial oils and emulsions act on the surface. Some chemicals may, however, corrode the surface. This depends on the concentration exposure time temperature of the agents used. Changes to the dimensions of Plastic panels due to the absorption of moisture and thermal expansion should be taken into account when installing them in frame structures. These panels may warp if exposed to moisture on one side only. Note: RAL numbers of colours apply to varnishes. Due to the different manufacturing processes, the brilliance and colouring of laminated Plastic panels can vary greatly. Consequently, if there is any doubt a comparison should always be made with original samples provided by your item sales partner. Property Value Test standard Density 1.4 g/cm 3 Wearing resistance 450 min -1 EN 438 T2 Scratch resistance 3.0 N EN 438 Flexural strength 1 N/mm² EN 438 T2 Modulus of elasticity 12,000 N/mm² EN 438 T2 Tensile strength 80 N/mm² EN 438 T2 Coefficient of thermal expansion 20 x -6 K -1 DIN Construction material class B 2 DIN 42 Surface resistance < 11 Ohm DIN

11 The following applies to all the products below: Resin-bonded cellulose laminate similar to RAL colour code Thickness tolerance ± 8% Panel dimensions approx. 2800x1850 mm Plastic 4mm m = 5.72 kg/m 2 white similar to RA L 9016, cut-off max. 2770x1820 mm white similar to RA L 9016, 1 pce. panel dimensions. max. 2800x1850 mm green, similar to RAL 6000, cut-off max. 2770x1820 mm green, similar to RAL 6000, 1 pce. panel dimensions. max. 2800x1850 mm red, similar to RAL 3000, cut-off max. 2770x1820 mm red, similar to RAL 3000, 1 pce. panel dimensions. max. 2800x1850 mm yellow, similar to RAL 34, cut-off max. 2770x1820 mm yellow, similar to RAL 34, 1 pce. panel dimensions. max. 2800x1850 mm blue, similar to RAL 5024, cut-off max. 2770x1820 mm blue, similar to RAL 5024, 1 pce. panel dimensions. max. 2800x1850 mm grey, similar to RAL 7035, cut-off max. 2770x1820 mm grey, similar to RAL 7030, cut-off max. 2770x1820 mm grey, similar to RAL 7035, 1 pce. panel dimensions. max. 2800x1850 mm grey, similar to RAL 7030, 1 pce. panel dimensions. max. 2800x1850 mm black, similar to RAL 9017, cut-off max. 2770x1820 mm black, similar to RAL 9017, 1 pce. panel dimensions. max. 2800x1850 mm Plastic mm m = kg/m 2 white similar to RA L 9016, cut-off max. 2770x1820 mm white similar to RA L 9016, 1 pce. panel dimensions. max. 2800x1850 mm green, similar to RAL 6000, cut-off max. 2770x1820 mm green, similar to RAL 6000, 1 pce. panel dimensions. max. 2800x1850 mm red, similar to RAL 3000, cut-off max. 2770x1820 mm red, similar to RAL 3000, 1 pce. panel dimensions. max. 2800x1850 mm yellow, similar to RAL 34, cut-off max. 2770x1820 mm yellow, similar to RAL 34, 1 pce. panel dimensions. max. 2800x1850 mm blue, similar to RAL 5024, cut-off max. 2770x1820 mm blue, similar to RAL 5024, 1 pce. panel dimensions. max. 2800x1850 mm grey, similar to RAL 7035, cut-off max. 2770x1820 mm grey, similar to RAL 7030, cut-off max. 2770x1820 mm grey, similar to RAL 7035, 1 pce. panel dimensions. max. 2800x1850 mm grey, similar to RAL 7030, 1 pce. panel dimensions. max. 2800x1850 mm black, similar to RAL 9017, cut-off max. 2770x1820 mm black, similar to RAL 9017, 1 pce. panel dimensions. max. 2800x1850 mm

12 Plastic ESD For the protection of electronic components For maximum conductivity requirements Meets EPA requirements The Plastic ESD panel is specifically designed for use in EPA workplaces where the handling of electronic components makes special safety precautions necessary (EPA = Electrostatic Protected Area). The low discharge resistance (7.5x 5 Ω < R < 9 Ω) on the surface of the panel and in the core of the material allows it to be used as a table top without need for an additional conductive edge strip, or to be used in workpiece carriers with milling or drilled holes whose cut edges have the same discharge properties as the surface. It has the same resistance to mechanical, thermal and chemical loading as the standard antistatic design. The presence of additives to facilitate electrostatic discharge can result in slight deviations in colour in the surface layer and core material. Property Value Test Standard Density 1.4 g/cm 3 Wearing resistance 450 min -1 EN 438 T2 Scratch resistance 3.0 N EN 438 Flexural strength 1 N/mm² EN 438 T2 Modulus of elasticity 12,000 N/mm² EN 438 T2 Tensile strength 80 N/mm² EN 438 T2 Coefficient of thermal expansion 20 x -6 K -1 DIN Construction material class B 2 DIN 42 Surface resistance 7.5x 5 Ω < R < 9 Ω DIN Plastic 4mm, ESD Resin-bonded cellulose laminate Panel dimensions approx. 2440x1220 mm m = 5.70 kg/m 2 grey, similar to RAL 7035, cut-off max. 24x1190 mm grey, similar to RAL 7035, 1 pce. panel dimensions. max. 2440x1220 mm Plastic mm, ESD Resin-bonded cellulose laminate Panel dimensions approx. 2440x1220 mm m = kg/m 2 grey, similar to RAL 7035, cut-off max. 24x1190 mm grey, similar to RAL 7035, 1 pce. panel dimensions. max. 2440x1220 mm Plastic 16mm, ESD Resin-bonded cellulose laminate Panel dimensions approx. 2440x1220 mm m = kg/m 2 grey, similar to RAL 7035, cut-off max. 24x1190 mm grey, similar to RAL 7035, 1 pce. panel dimensions. max. 2440x1220 mm

13 Chequer Sheet Stable and non-slip Aluminium chequer sheet is used for walk-on surfaces or steps. Property Value Density 2.7 g/cm³ Modulus of elasticity 70,000 N/mm² Tensile strength 200 N/mm² Ductile yield A5 5% Chequer Sheet Al 5mm AlMg3 Duett chequering DIN EN 1386 Sheet Thickness 3.5 mm Panel dimensions approx. 3000x1500mm m = 9.90 kg/m 2 cold rolled (not degreased), cut-off max. 2970x1470 mm cold rolled (not degreased), 1 pce. panel dimensions. max. 3000x1500 mm

14 Corrugated Mesh Al For lightweight guards and enclosures Particularly easy to machine Corrugated Meshes are suitable for guards, enclosures and partitions, in particular when combined with Clamp Profiles. The use of anodized aluminium wires enables them to be used both indoors and outdoors on a permanent basis. Note on cutting Corrugated Mesh Al to size: Because of the way the material behaves when cut, the cut-off tolerances are in DIN ISO 2768 tolerance class c. Property Value Density 2.7 g/cm 3 Modulus of elasticity 70,000 N/mm² Tensile strength 120 N/mm² Ductile yield A5 5 % Anodized natural E6/EV1 Min. layer thickness μm Layer hardness HV Corrugated Mesh Al 3mm 20x20 Al, anodized Panel dimensions approx. 3000x18 mm Minimum cut-off width 150 mm Mesh: 20 mm Wire thickness: 3 mm m = 1.80 kg/m 2 natural anodized, cut-off max. 2970x1780 mm natural anodized, 1 pce. max. 3000x18 mm Corrugated Mesh Al 4mm 30x30 Al, anodized Panel dimensions approx. 3000x18 mm Minimum cut-off width 150 mm Mesh: 30 mm Wire thickness: 4 mm m = 2. kg/m 2 natural anodized, cut-off max. 2970x1780 mm natural anodized, 1 pce. max. 3000x18 mm

15 Corrugated Mesh St For high-strength fixtures Available in three mesh sizes Corrugated Meshes St are ideal for safety equipment which is subject to high stresses because of the very rigid steel wire they employ. They are fixed in special Clamp Profiles. Corrugated Meshes St are made from electrogalvanized wires. Note on cutting Corrugated Mesh St to size: Because of the way the material behaves when cut, the cut-off tolerances are in DIN ISO 2768 tolerance class c. Property Density Modulus of elasticity Tensile strength Galvanizing Value 7.85 g/cm³ 2,000 N/mm² 350 N/mm² DIN Fe/Zn 12A Materials used in all the following products: St Corrugated Mesh St 3mm 20x20 Panel dimensions approx. 3000x18 mm Minimum cut-off width 150 mm Mesh: 20 mm Wire thickness: 3 mm m = 5.00 kg/m 2 bright zinc-plated, cut-off max. 2970x1780 mm bright zinc-plated, 1 pce. max. 3000x18 mm Corrugated Mesh St 4mm 30x30 Panel dimensions approx. 3000x18 mm Minimum cut-off width 150 mm Mesh: 30 mm Wire thickness: 4 mm m = 6.20 kg/m 2 bright zinc-plated, cut-off max. 2970x1780 mm bright zinc-plated, 1 pce. max. 3000x18 mm Corrugated Mesh St 4mm 40x40 Panel dimensions approx. 3000x18 mm Minimum cut-off width 150 mm Mesh: 40 mm Wire thickness: 4 mm m = 4.50 kg/m 2 bright zinc-plated, cut-off max. 2970x1780 mm bright zinc-plated, 1 pce. max. 3000x18 mm

16 Dual-Rod Mesh Stable even without a frame Two mesh widths available Inherently stable panel element for constructing free-standing protective fence structures. Available in two different mesh widths (25 and 50 mm). The Dual-Rod Meshes are hot-dip galvanized to protect against corrosion. They can also be painted to suit customers individual needs. Black Dual-Rod Meshes are supplied powder coated from the factory. Property Density Modulus of elasticity Tensile strength Hot-dip galvanizing Powder coating Value 7.85 g/cm³ 2,000 N/mm² 350 N/mm² Min. layer thickness 70 μm Black RAL9005 Min. layer thickness 70 μm The narrow openings of the mesh prevent people from reaching through (as required by EN 294). Property Value Mesh width [mm] Opening dimension a [mm] Distance to danger zone b [mm] > 120 > 850 Dual-Rod Mesh Hanger 213 Materials used in all the following products: St Dual-Rod Mesh 25x200, 1830x958 Wire diameter: 6/8 mm Mesh width: 25x200 mm Height: 1830 mm Width: 958 mm m = 20.5 kg bright zinc-plated, 1 pce Dual-Rod Mesh 25x200, 1830x958 Wire diameter: 6/8 mm Mesh width: 25x200 mm Height: 1830 mm Width: 958 mm m = 22.0 kg black, 1 pce /50 958/2008 Dual-Rod Mesh 25x200, 1830x2008 Wire diameter: 6/8 mm Mesh width: 25x200 mm Height: 1830 mm Width: 2008 mm m = 42.3 kg bright zinc-plated, 1 pce

17 Dual-Rod Mesh 25x200, 1830x2008 Wire diameter: 6/8 mm Mesh width: 25x200 mm Height: 1830 mm Width: 2008 mm m = 45.0 kg black, 1 pce Dual-Rod Mesh 50x200, 1830x958 Wire diameter: 6/8 mm Mesh width: 50x200 mm Height: 1830 mm Width: 958 mm m = 13.8 kg bright zinc-plated, 1 pce Dual-Rod Mesh 50x200, 1830x958 Wire diameter: 6/8 mm Mesh width: 50x200 mm Height: 1830 mm Width: 958 mm m = 14.5 kg black, 1 pce Dual-Rod Mesh 50x200, 1830x2008 Wire diameter: 6/8 mm Mesh width: 50x200 mm Height: 1830 mm Width: 2008 mm m = 28.6 kg bright zinc-plated, 1 pce Dual-Rod Mesh 50x200, 1830x2008 Wire diameter: 6/8 mm Mesh width: 50x200 mm Height: 1830 mm Width: 2008 mm m = 30.0 kg black, 1 pce

18 Steel Mesh Stable and strong Light objects can be hung on it Due to the high inherent stability of the Steel Mesh (straight wires, welded), it is also highly suitable for direct use in the profile groove. Property Density Modulus of elasticity Tensile strength Galvanizing Powder coating Value 7.85 g/cm³ 2,000 N/mm² 350 N/mm² 60 g/m² Black RAL 9005, min. layer thickness 70 μm Steel Mesh 3.8mm 40x40 Steel wire (straight wires) Welded, electrogalvanized Approx. 2500x00 mm Mesh: 40 mm Wire thickness: 3.8 mm m = 5. kg/m 2 bright zinc-plated, cut-off max. 2470x970 mm bright zinc-plated, 1 pce. max. 2000x00 mm Steel Mesh 3.8mm 40x40 Steel wire (straight wires) Welded, hot-dip galvanized and powder coated Approx. 2000x00 mm Mesh: 40 mm Wire thickness: 3.8 mm m = 5.30 kg/m 2 black, cut-off max. 1970x970 mm black, 1 pce. max. 2000x00 mm

19 Perforated Sheet Stylish and air-permeable For use as screening or ventilation openings Aluminium Perforated Sheet has a wide range of applications. It can be used to provide screening, for floors and ceilings that permit the passage of air or dust, for storage surfaces or for decorative wall panelling. The powder-coated version is weather-proof. Property Density Modulus of elasticity Tensile strength Galvanizing Powder coating Value 2.7 g/cm³ 70,000 N/mm² 200 N/mm² 60 g/m² Black RAL9005 Min. layer thickness 70 μm Perforated Sheet Al 3mm AlMg3 Cold rolled (not degreased) or coated Hole diameter = mm in offset rows DIN 24041; residual area approx. 60% Panel dimensions approx. 3000x1500 mm m = 4.80 kg/m 2 cold rolled (not degreased), cut-off max. 2970x1470 mm cold rolled (not degreased), 1 pce. panel dimensions. max. 3000x1500 mm black, cut-off max. 2970x1470 mm black, 1 pce. panel dimensions. max. 3000x1500 mm

20 Sound-Insulating Material Create a peaceful environment in offices and production halls Absorbs noise in medium and high frequencies Suitable as a panel element in hoods and enclosures For functional partitions in open-plan offices Sound-Insulating Material for reducing the effect of sound emission to the environment can be used for both complete encapsulation and individual partitions. It is self-adhesive on one side (rubber-based adhesive). The Sound-Insulating Material is glued to a panel element. The panel element should be fastened in the profile frame in such a way that as little vibration or sound is transmitted as possible. The sound-insulating effect depends on the excitation frequency. Sound-Insulating Material 20mm PUR-ester special foam Coated with PVC film perforated, easy to wash down, Sound absorption as per DIN Temperature resistance: -40 C to +0 C Thermal conductivity: W/mK, DIN Fire characteristics: self-extinguishing to FMVSS 302, DIN Panel dimensions 480x480 mm m = g anthracite, 1 pce

21 Edge Profile S3 Al Attractive finish Covering for sharp cut edges Edge Profile as edging for 3 mm thick panel elements whose cut edges require covering, e.g. Perforated Sheet Al etc. The Edge Profile can be cut at a 90 angle or with a mitre cut Edge Profile S3 Al Al, anodized A [cm 2 ] m [g/m] natural, 1 pce., length 2000 mm black, 1 pce., length 2000 mm