ESR ICC Evaluation Service, Inc. Issued May 1, 2008 This report is subject to re-examination in one year.

Size: px
Start display at page:

Download "ESR ICC Evaluation Service, Inc. Issued May 1, 2008 This report is subject to re-examination in one year."

Transcription

1 ESR-275 Issued May 1, 08 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. Business/Regional Office # 530 Workman Mill Road, Whittier, California 9001 # (52) Regional Office # 900 Montclair Road, Suite A, Birmingham, Alabama # (5) Regional Office # 051 West Flossmoor Road, Country Club Hills, Illinois 078 # (708) DIVISION: 0 WOOD AND PLASTICS Section: 0090 Wood and Plastic Fastenings UNITED STEEL PRODUCTS COMPANY 703 ROGERS DRIVE MONTGOMERY, MINNESOTA info@uspconnectors.com SUBJECT USP Lumber Connectors: 1.1 JN and JNE Joist Hangers 1.2 HH Header Hangers 1.3 FH and FHD Purlin Hangers 1. HJC Hip Jack Hangers 1.5 LS Adjustable Slope Hangers 1. ZC Blocking Hangers 1.7 SFC Framing Clip Hangers 1.8 FTC Floor Truss Clips 1.9 KFTA and KLFTA Floor Tie Straps 1.10 SPT Stud-Plate Ties 1.11 STC Scissor Truss Connectors 1.12 KAG Angle Gussets 1.13 DSC Drag Strut 1.1 HHCP Corner Anchor Connector 1.15 JPF Joist Hanger Connector 1.1 LUGT & LUGTC Girder Tie Connector 1.17 MSTC Strap Tie Connector PROPERTY EVALUATED: Structural 2.0 USES The USP connectors described in this report are used as wood framing connectors in accordance with Section of the IBC. The products may also be used in structures regulated under the IRC when an engineered design is submitted in accordance with Section R of the IRC. 3.0 DESCRIPTION 3.1 Models: JN and JNE Joist Hangers: JN and JNE joist hangers are fabricated from galvanized steel of and gage thickness, respectively. These U-shaped hangers are designed to support one and two ply nominal 2 in. in. (51 mm 152 mm) and 2 in. 8 in. (51 mm 3 mm) wood joists. The hangers are available with 1 5 / 8 in. (1.3 mm) and 2 in. (51 mm) seat depths. See Table 1 for the hanger dimensions, fastener schedule, and allowable loads. See Figure 1 for details HH Header Hangers: HH Header Hangers are alternatives to cripple studs at wood headers. HH Hangers are fabricated from 1 gage galvanized steel and are sized to accommodate 3 9/1 in. (90 mm) and 5 ½ in. (10 mm) wide headers and header supporting members. HH Hangers provide a 2 in. deep (51 mm) saddle seat for the header fastened to both sides of the header and post and the post face under the header with 1d nails. See Table 2 for the hanger dimensions, fastener schedule, and allowable loads. See Figure 2 for details FH and FHD Purlin Hangers: FH and FHD Purlin Hangers support 2 in. in. (51 mm 102 mm) or 2 in. in. (51 mm 152 mm) wood framing members and are fabricated from gage galvanized steel. FHD Hangers are installed in a saddle configuration, while the FH is a single side application. FH Hangers have 1 ½ in. deep (38 mm) seats that are 1 9/1 in. (39. mm) in width, and varying height. The hangers are prepunched for 1d and 10d common nails. See Table 3 for the hanger dimensions, fastener schedule, and allowable loads. See Figure 3 for details HJC HIP Jack Hangers: HJC Hip Jack Hangers are designed to support single ply hip and jack trusses from double ply girder trusses. The hip is installed at 5 degrees with respect to the jack truss. HJC Hangers are fabricated from 12 gage galvanized steel. The hanger is pre-punched for 1d common nails into the supporting girder bottom chord and 10d common nails for nailing into the hip and jack members. See Table for the hanger dimensions, fastener schedule, and allowable loads. See Figure for details LS ADJUSTABLE Slope Hangers: LS Adjustable Slope Hangers are fabricated from gage galvanized steel and are used as adjustable connectors for slopes in the plane perpendicular to the header longitudinal axis, up to 5 degrees upwards or downwards from the line perpendicular to the header axis. The seat depth and width is 3 in. (7 mm) and 1 9/1 in. (39. mm), respectively, with varying heights. The hanger is prepunched for 1d and 10d 1 ½ common nails. See Table 5 for the hanger dimensions, fastener schedule, and allowable loads. See Figure 5 for details ZC Blocking Hangers: ZC Blocking Hangers are hangers designed to support nominal 2 in. in. (51 mm 102 mm), 2 in. in. (51 mm 152 mm), and in. 2 in (102 mm 51 mm) wood blocking members. ZC Hangers are fabricated from or 12 gage galvanized steel and are prepunched for 10d nails. See Table for the hanger dimensions, fastener schedule, and allowable loads. See Figure for details. are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, Inc., express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright 08 Page 1 of 17

2 Page 2 of 17 ESR SFC Framing Clip Hangers: SFC Framing Clips are alternatives to cripple studs. SFC Hangers are fabricated from 1 gage galvanized steel and provide a 1 ½ in. deep (38 mm) saddle seat for support of in. (102 mm), in. (152 mm), or 8 in. (3 mm) nominal dimension header members. SFC hangers are prepunched for 10d nails to fasten the header on two sides, to the hanger, and for 1d nails to fasten the hanger on two sides of the post. See Table 7 for the hanger dimensions, fastener schedule, and allowable loads. See Figure 7 for details FTC Floor Truss Clips: FTC Floor Truss Clips are fabricated from gage galvanized steel and are designed to transfer normal vertical loads between two floor trusses having single ply chords or double ply chords to act as a single floor girder truss. See Table 8 for clip dimensions, fastener schedule, and allowable loads. See Figure 8 for details KFTA and Klfta Floor Tie Straps: KFTA and KLFTA anchors transfer tensile forces from vertical wall studs, above a floor assembly, to the vertical wall studs directly below a floor assembly. The straps are sized to accommodate floor construction utilizing at a maximum 2 in. 12 in. (51 mm 305 mm) nominal floor joists. The KFTA strap is manufactured from 10 gage or 3 gage hot rolled steel and is installed with bolts. The KLFTA strap is manufactured from 1 gage galvanized steel and is installed with nails. See Table 9 for strap dimensions, fastener schedule, and allowable loads. See Figure 9 for details SPT Stud-Plate Ties: SPT stud-plates are fabricated from gage galvanized steel. SPT 22 and 2 series stud plates are designed to fasten to a single plate. SPT and SPT series stud plates are designed to accommodate double or triple studs or plates. SPT 22 and 2 plates are prepunched to accept 10d common nails and SPT and SPT plates are prepunched to accept 1d nails. Nails fastened to the wide face of the stud shall be driven at 30 degrees from the perpendicular on the horizontal plane. See Table 10 for dimensions, fastener schedule, and allowable loads. See Figure 10 for details STC Scissor Truss Connectors: STC Scissor Truss connectors are fabricated from 12 gage galvanized steel and is used to connect a single-ply scissor truss to a nominal 2 in. in. (51 mm 102 mm) or in. (152 mm) or 8 in. (3 mm) wall top plate. The connector has prepunched horizontal nail slots for horizontal adjustment of the scissor truss and prepunched flanges for 10d common nails into wood top sill plates. See Table 11 for the connector dimensions, fastener schedule, and allowable loads. See Figure 11 for details KAG Angle Gussets: KAG Angle Gussets connect wood framing members to other wood framing members, using bolts, and are formed from 7 or 3 gage hot rolled steel. See Table 12 for gusset dimensions, fastener schedule, and allowable loads. See Figure 12 for details DSC Drag Strut: Designed to tie wooden truss members to the top plates in a wall system. The struts are fabricated from 3 gage thickness, painted, hot rolled steel. The strut is pre-punched for 1 / inch nominal diameter wood screws WS3 manufactured by USPC. See Table 13 for fastener schedule, and allowable loads. See Figure 13 for details HHCP Corner Anchor Connector: Designed to connect hip rafters or trusses to wall top plates at 5 degree angle. Fabricated from gage galvanized steel. See Table 1 for fastener schedule and allowable loads. See Figure 1 for details JPF JOIST HANGER CONNECTOR: Designed to support nominal 2x lumber. Fabricated from gage galvanized steel. The connectors consist of U shaped straps with bent top flanges, constant width and different heights. The hangers are pre-punched for 10d common wire nails. The joist nails are driven at 30 to 5 degrees horizontally through the joist into the header such that the joist is toe-nailed to the header. See Table 15 for fastener schedule and allowable loads. See Figure 15 for details LUGT & LUGTC GIRDER TIE CONNECTOR: Designed to connect girder trusses and other framing members to the top of stud walls and studs or posts. Fabricated from 1 gage galvanized steel. See Table 1 for fastener schedule and allowable loads. See Figure 1 for details MSTC STRAP TIE CONNECTOR: Designed to connect wood framing to resist tension forces. Fabricated from 1 and 1 gage galvanized steel. See Table 17 for fastener schedule and allowable loads. See Figure 17 for details. 3.2 MATERIALS : The minimum bare metal thickness and the grade of steel of the USP Lumber Connectors in this report is indicated in Table of this report Wood: Wood elements shall have dimensions consistent with the connector dimensions indicated in the design Tables in this report. Allowable design values are based on lumber having a minimum specific gravity of 0.50, such as Douglas fir-larch, with moisture content not exceeding 19 percent, and an in-service temperature of 100 F (37.8 C) or less Fasteners Nails: Nails shall comply with Federal Specification FF-N-105B or ASTM F 17, and shall have the following minimum bending yield strengths (Fyb): Size (gage) 10d (9 ga) 10dx (9a) 1d (8a) Diameter (inch) Length (inches Head Diameter (inch) Fyb (psi) , , / , / NA 10,000 P - nail / , Nails shall have annular rings over half the shank length. 2. P nails denotes fasteners designed specifically to be installed with a pneumatic-powered nailer. 3. Galvanized coatings shall meet ASTM A 1 Class 1.. NA=Not applicable. 5. For Sl:1 inch = 25. mm, 1 psi =.89 kpa Bolts: Bolts shall comply with ASTM A 307 and shall have a minimum bending yield strength of 5,000 psi (310 Mpa)..0 DESIGN AND INSTALLATION.1 Installation: USP Lumber Connectors shall be installed in accordance with the manufacturer's published installation instructions. The manufacturer's published installation instructions and this report shall be strictly adhered to and a copy of these instructions shall be available at all times on the job site during installation. The instructions within this report govern if there are any conflicts between the manufacturer's published installation instructions and this report.

3 Page 3 of 17 ESR Design: Connected wood members shall be designed to support the required design load. Tabulated design loads for the connectors evaluated in this report are based on the lowest load obtained from comparing:! Least test load that causes 1 / 8 inch (3.2 mm) deflection.! Lowest ultimate test load with a safety factor of 3.0.! Allowable fastener capacity taking into account load duration factors and bearing capacity (compression perpendicular to grain value in wood), in accordance with the NDS, based on wood with a specific gravity of The torsional moment capacity for normal duration of loading of the joist hanger is based on the average torsional moment at which the lateral movement of the top or bottom of the joist with respect to the original position of joist is 1 / 8 inch. The connected wood member shall be designed for the design loads. Allowable values are for connections in wood seasoned to a moisture content of 19 percent or less and used under continuously dry conditions. For connections in wood that is unseasoned or partially seasoned, the allowable loads in this report shall be multiplied by the moisture content factor, CM, specified in the applicable building code. Tabular load capacities are based on wood with a minimum specific gravity of 0.50 and a moisture content less than 19 percent. Tabulated allowable design loads are for loads of normal duration. Adjustments to these values shall be permitted for other durations of loading, i.e. plus 15 percent for two months duration (snow), or plus 33 percent for wind or seismic. Tabulated allowable design loads shall be reduced 10 percent for design load durations longer than 10 years. The resulting allowable design load after adjustment shall not exceed the maximum design load shown in the tables. Uplift loads shown in the tables include a 33-1/3% increase for compliance with the Uniform Building Code and the Standard Building Code, and a 0% increase for compliance with the BOCA National Building Code for wind or seismic load conditions. When using products in jurisdictions which have adopted the International Building Code, uplift loads include a 33-1/3% increase for wind and seismic load conditions and require the use of the load combinations of Section of the IBC. No further increases are permitted..3 Special Inspection:.3.1 IBC: For jurisdiction adopting the IBC, periodic special inspection must be provided for components within the seismic-force-resisting system in Seismic Design Categories C, D, E or F in accordance with IBC Section or 1707., with the exception of those structures that qualify under IBC Section IRC: For jurisdictions adopting the IRC, special inspections are not required. 5.0 IDENTIFICATION Each of the USP Lumber Connectors covered by this report shall be labeled with the manufacturer s name/and or trademark, series designation and evaluation report number, NER-5..0 EVIDENCE SUBMITTED Data in accordance with the ICC-ES Acceptance Criteria for Joist Hangers and Similar Devices (AC13), dated October 0 (corrected March 07). 7.0 CONDITIONS OF USE The USP lumber connectors described in this report comply with, or are suitable alternatives to what is specified in, the 0 International Building Code, the 0 International Residential Code, the BOCA National Building Code /1999, the 1999 Standard Building Code and the 1997 Uniform Building Code, subject to the following conditions: 7.1 This evaluation report and the manufacturer s published installation instructions, when required by the code official, shall be submitted at the time of permit application. 7.2 The connectors are manufactured, identified and installed in accordance with this report and the manufacturer s installation instructions. 7.3 Maximum allowable loads for the connectors shall be determined with applicable duration loads noted in the design Tables in this report, using the applicable load duration factors. 7. Allowable values listed in this report are for connections in wood with a moisture content of 19 percent or less and used under dry conditions of use. 7.5 Adjustment factors noted in the applicable code and in the NDS for wet-service conditions, and elevated temperatures shall be considered where applicable. 7. Allowable loads are based on attachments to Douglas fir-larch having a minimum specific gravity of For other species, loads are to be adjusted in accordance with the applicable code. 7.7 Framing members supported by the connectors shall be designed in accordance with the applicable code. 7.8 The torsional moment capacity of all joist hangers, except for FH 2/28/210/212, JN and JNE series, and LS series hangers, is outside the scope of this report and shall be assumed to be zero. 7.9 Design calculations and details for specific applications shall be furnished to the code official verifying compliance with this report and the applicable code. The individual preparing such documents shall possess the necessary credentials regarding competency and qualifications as required by the applicable code and the professional registration laws of the state where the construction is undertaken Uplift loads shown in the tables include a 33-1/3% increase for compliance with the Uniform Building Code and the Standard Building Code, and a 0% increase for compliance with the BOCA National Building Code for wind or seismic load conditions. When using products in jurisdictions which have adopted the International Building Code, uplift loads include a 0% increase for wind and seismic load conditions and require the use of the load combinations of Section of the IBC. No further increases are permitted The lumber treater and USP should be contacted for recommendations on the appropriate coating or material to specify for use with steel connectors and fasteners in contact with specific proprietary preservative treated or fire retardant treated lumber Nails and bolts used in contact with preservative treated or fire retardant treated lumber must comply with IBC Section or IRC Section R 319.3, as applicable For use with treated lumber, the lumber treater or USP, or both, should be contacted for information concerning connection capacities of fasteners used with specific proprietary preservative treated or fire retardant treated lumber.

4 Page of 17 ESR-275 Joist Width (in.) Table 1 JN & JNE Joist Hangers Dimensions (in.) Fastener Schedule Allowable Loads (lbs) W H D Header P Nails JN2 JN28 1-9/1 1-9/ /8 1-5/ JN2-2 JN28-2 (2) (2) 3-1/1 3-1/1 5-3/8 7-1/8 1-5/8 1-5/ JN2E JN28E 1-9/1 1-9/1 5-1/ -7/ Joist P Nails F cz = 0 psi F cz = 25 psi Uplift 100% 115% 125% 100% 115% 125% 133% 10% 1 Fasteners shall be pneumatically driven to firmly seat the nail head against the hanger steel, without embedding the nail head in the metal surface. 2 The quantity of nails installed shall be equally distributed to both sides of the hanger, and shall be located vertically at 1 in. on center. Vertical rows shall be spaced 1/2 in. on center. Minimum sheared edge distance to a fastener shall be 3/8 in. Minimum formed edge distance to a fastener shall be 1/2 in. 3 Uplift loads have been increased 33-1/3% and 0% for wind or seismic load conditions. Further increase shall not be permitted. Maximum allowable torsional moment capacity shall be 1700 inch-lbs For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N. FIGURE 1

5 Page 5 of 17 ESR-275 Table 2 HH Header Hanger Dimensions (in.) Fasteners Allowable Loads (lbs.) W H Stud Header Load 100% 115% 125% 133% 10% HH 1 3-9/1 3-1/ 9-1d -1d F 1 F 2 F 3 HH 1 5-1/2 5-1/ 12-1d -1d F 1 F 2 F 3 1. Lumber shall be no less than 2 in. thick both horizontally and vertically to achieve table load values. 2. Load values include increases for various durations of load, including 33-1/3% and 0% for wind or seismic load conditions, and shall not be further increased. 3. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N FIGURE 2

6 Page of 17 ESR-275 Joist Width (in.) Table 3 FH & FHD Purlin Hangers Dimensions (in.) Fasteners Allowable Loads (lbs.) W H D TF FH2 1-9/1 5-3/8 1 7/1 FH28 1-9/1 7-1/ 1 7/1 FH /1 9-1/ 1 7/1 FH /1 11-1/ 1 7/1 FH21 1-9/1 13-1/ 1 7/1 Header Joist F cz = 0 psi F cz = 25 psi Uplift Top Face Type Qty Type 100% 115% 125% 100% 115% 125% 133% 10% d 1d d 10d 1. Header thickness shall be no less than in. for 10d nails, or 2 in. for 1d nails (3-1/2 in. for FHD hangers). 2. For FHD models, the TF dimension is specified and is not less than in. 3. Uplift load values are increased 33-1/3% and 0% for wind or seismic load conditions and shall not be further increased.. The allowable load values apply to either side of the FHD saddled version of the FH hangers. 5. F cz = Compression perpendicular to grain.. Maximum allowable torsional moment capacity for FH2, FH28, FH210, and FH212 hanger shall be 130 inch-lbs. 7. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N FIGURE 3

7 Page 7 of 17 ESR-275 HJC 2 HJC Table HJC Hip Jack Hangers Dimensions (in.) Fasteners Allowable Loads (lbs.) W H D Girder Jack Hip 5-3/8 7-1/8 3-1/ 3-1/ 1-1d - 1d 7-10d 8-10d 5-10d - 10d F cz = 0 psi Uplift 100% 115% 125% 133% 10% Hip and jack trusses are limited to a single ply each. The hip shall be set at 5 degrees to the jack. 2. Uplift loads are increased 33-1/3% or 0% for wind or seismic load conditions and shall not be further increased. 3. Allowable loads assume the hip and jack trusses act in unison.. Trusses shall be provided with blocking or other means to prevent rotation. 5. F cz = Compression perpendicular to grain.. For SI: 1 in. = 25. mm, 1 lbf =.5 N, 1 psi =.89 kpa FIGURE

8 Page 8 of 17 ESR-275 LS28 LS210 Table 5 LS Adjustable Slope Hangers Dimensions (in.) Fasteners Allowable Loads (lbs.) W H D 1-9/1 1-9/1 5-1/2 8-1/8 3 3 Header Joist F cz = 25psi Uplift Qty Type Qty Type 100% 115% 125% 133% 10% d 1d 10d 1d 1. Uplift loads include a 33-1/3% or 0% increase for wind or seismic load conditions and shall not be further increased. 2. F cz = Compression perpendicular to grain. 3. Maximum allowable torsional moment capacity shall be 1070 inch-lbs.. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N d 10d 10d 10d FIGURE 5 ZC 2 ZC ZC Table ZC Blocking Hangers Dimensions (in.) Fasteners Allowable Loads (lbs.) (100%) W D H Header Blocking F cz = 0 F cz = / 1-3/8 1-3/8 1-9/1 3-9/1 5-9/1 (3) 10d (2) 10d (2) 10d (2) 10d (1) 10d (1) 10d 1. One of the quantity of nails shown installed to header, fastened through the vertical portion of the ZC hanger, is permitted to be fastened to the end of the blocking, or omitted with no reduction in load. 2. Allowable loads shall not be increased. 3. F cz = Compression perpendicular to grain.. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N FIGURE

9 Page 9 of 17 ESR-275 SFC SFC SFC Table 7 SFC Framing Clip Hangers Dimensions (in.) Fasteners Allowable Loads (lbs.) W D H 3-9/1 5-1/2 7-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 Stud/Post Joist/Header F 1 F 2 Qty Type Qty Type 100% 115% 125% 133% 10% 100% 115% 125% 133% 10% 5 1d 1d 1d 5 10d 10d 10d The 1d nails into the supported member shall have an embedment into the supporting wood of no less than 2 in. 2. Allowable loads are increased for duration of load up to 33-1/3% and 0% for wind and seismic load conditions and shall not be further increased. 3. Loads in the F1 direction include bearing for the supported member, with compression perpendicular to grain of 0 psi, or greater.. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N FIGURE 7 Table 8 FTC Floor Truss Clips Number FTC 1 FTC 2 FTC 32 FTC 32-2 Wood Member 1 ply 2 2 ply 2 1 ply ply 3 2 Dimensions (in.) L 1 L 2 H 3-1/1 3-1/1 2-1/1 2-1/1-5/8-5/8 3-5/8 3-5/8 3 3 Fasteners 10-10d 10-10d 10-10d 10-10d Allowable Loads (lbs.) (100%) 1. The FTC1 and FTC32 are intended for use with single ply chord floor truss systems; and the FTC2 and FTC32-2 are intended for double ply chord floor truss systems. 2. Allowable loads shall not be increased. 3. For SI: 1 in. = 25. mm, 1 lbf =.5 N, 1 psi =.89 kpa FIGURE 8

10 Page 10 of 17 ESR-275 KFTA 2 KFTA 5 KFTA 7 KLFTA Table 9 KFTA & KLFTA Floor Tie Straps 1,2,3, Dimensions (in.) Fasteners Allowable Uplift Load (lbs.) W L O Nails Bolts 3 3-1/2 3-1/2 2-3/8 37-1/2 5-1/ / (1) 10d () 5/8 () 3/ () 7/8 1. The quantity of fasteners is the total quantity, with half the number installed at either end of the strap. 2. Allowable uplift loads vary with the thickness of wood to which the fasteners are installed. Note that the values for the 10d nail are reduced by the penetration factor of divided by Allowable uplift loads have been increased 33-1/3% and 0% for wind or seismic load conditions and shall not be further increased.. For SI: 1 in. = 25. mm, 1 lbf =.5 N, 1 psi =.89 kpa. Stud Thickness (in.) in. 3 in. -1/2 in. 100% 133% 10% 100% 133% 10% 100% 133% 10% FIGURE SPT22 SPT2 SPT SPT H (in.) -3/8 5-5/8-3/ -3/ Table 10 SPT Stud-Plate Ties Dimensions Fasteners Allowable Loads (lbs.) W (in.) Uplift F1 F2 Stud Plate Stud Plate 100% 133% 10% 100% 133% 10% 100% 133% 10% 1-9/1 1-9/1 3-9/1 5-9/1 3-1/2 3-1/2-1/2 8-1/2 () 10d () 10d () 1d () 1d () 10d () 10d () 1d () 1d 1. The two nails fastened to the wide face of the stud shall be driven 30 degrees from the perpendicular on the horizontal plane. 2. Allowable loads are for a single SPT device per connection. If two SPT devices are used for a single connection, the listed loads are permitted to be doubled. 3. Allowable loads have been increased 33-1/3% and 0% for wind or seismic conditions and shall not be further increased.. For SI: 1 in. = 25. mm, 1 lbf =.5 N, 1 psi =.89 kpa FIGURE 10

11 Page 11 of 17 ESR-275 STC 2 STC 2 STC Table 11 STC Scissor Truss Connectors Dimensions (in.) Fasteners Allowable Uplift Loads (lbs.) W1 W2 Truss Plate 100% 133% 10% 3-9/1 5-1/2 7-1/ 1-5/8 5-10d -10d Allowable loads have been increased 33-1/3% and 0% for wind or seismic conditions and shall not be further increased. 2. The truss set into the STC connector shall be supported by an approved method to prevent rotation in the device. 3. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N. FIGURE 11 KAG 8 KAG Table 12 KAG Angle Gussets Dimensions (in.) Bolt Allowable Loads (lbs.) W L Schedule 100% 133% 10% 2-11/ /8 9-5/1 () 5/8 () 3/ 1. Loads have been increased 33-1/3% and 0% for wind or seismic conditions and shall not be further increased. 2. Loads apply where the installation and direction of load are parallel to the long axis of either flange, and the bolts are being loaded parallel to the grain of the attached wood members. 3. For SI: 1 in. = 25. mm, 1 psi =.89 kpa, 1 lbf =.5 N FIGURE 12 THESE DRAWINGS ARE FOR ILLUSTRATION PURPOSES ONLY. THEY ARE NOT INTENDED FOR USE AS CONSTRUCTION DOCUMENTS FOR THE PURPOSE OF DESIGN, FABRICATION OR ERECTION.

12 Page 12 of 17 ESR-275

13 Page 13 of 17 ESR-275

14 Page 1 of 17 ESR-275

15 Page 15 of 17 ESR-275

16 Page 1 of 17 ESR-275

17 Page 17 of 17 ESR-275 Table Material Specifications Connector ASTM Specification Mean Thickness (in.) Minimum Yield Strength (ksi) Minimum Tensile Strength (ksi) JN & JNE A 53 CQ / JN2-2/28-2 A 53 CQ / HH A 53 CQ / FH & FHD A 53 CQ / HJC A 53 CQ / LS A 53 SQ Grade / ZC2 A 53 CQ / ZC A 53 CQ / SFC A 53 CQ / FTC A 53 CQ / KFTA A 570 Grade / KFTA7 A / KLFTA A 53 SQ Grade / SPT A 53 SQ Grade / STC A 53 SQ Grade / KAG8 A 570 Grade / KAG9 A / DSC A570 Grade / HHCP A53 SS Grade / JPF A53 SS Grade / LUGT LUGTC A53 SS Grade / MSTC A53 SS Grade 0 1 & 1 For SI: 1 in. = 25. mm, ksi =.89 MPa. 1 GA / GA /

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: 0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 3448 Reissued 10/2016 This report is subject to renewal 10/2018. DIVISION: 06 00 00 WOOD, PLASTICS

More information

REPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT:

REPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 43 6587 (56) 699 0543 www.icc es.org ESR 3754 Reissued 09/07 This report is subject to renewal 09/09. DIVISION: 03 00 00 CONCRETE

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC AND COMPOSITE FASTENINGS REPORT HOLDER:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC AND COMPOSITE FASTENINGS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3444 Reissued 10/2016 This report is subject to renewal 10/2018. DIVISION: 06 00 00 WOOD, PLASTICS

More information

REPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT:

REPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2787 Reissued 05/2017 This report is subject to renewal 05/2019. DIVISION: 03 00

More information

ESR-2269 Reissued November 1, 2008 This report is subject to re-examination in one year.

ESR-2269 Reissued November 1, 2008 This report is subject to re-examination in one year. Reissued November, 008 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office 60 Workman Mill Road, Whittier, California 9060 (6) 699-0

More information

Joint Evaluation Report

Joint Evaluation Report 0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-1040 Reissued 09/2016 This report is subject to renewal 09/2018. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION:

More information

ESR ICC Evaluation Service, Inc. Reissued September 1, 2008 This report is subject to re-examination in one year.

ESR ICC Evaluation Service, Inc. Reissued September 1, 2008 This report is subject to re-examination in one year. ESR- Reissued September, 00 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 0 Workman Mill Road, Whittier, California 900 #

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: BOSTITCH FASTENING SYSTEMS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: BOSTITCH FASTENING SYSTEMS 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2122 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 06 00 00 WOOD, PLASTICS

More information

Originally Issued: 02/11/2011 Revised: 02/23/2018 Valid Through: 02/28/2019

Originally Issued: 02/11/2011 Revised: 02/23/2018 Valid Through: 02/28/2019 MITEK USA, INC. USP HOLDOWN AND TENSION-TIE CONNECTORS CSI Section: 06 05 23 Wood, Plastic and Composite Fastenings 1.0 RECOGNITION MiTek USA, Inc. USP holdown and tension-tie connectors recognized in

More information

Trusted ICC ES SECTION: Conformity! Look. Evaluation. ICC-ES Evaluation

Trusted ICC ES SECTION: Conformity! Look. Evaluation. ICC-ES Evaluation 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 3635 Reissued 04/2016 This report is subject to renewal 04/2018. DIVISION: 03 00

More information

REPORT HOLDER: FASTENING SPECIALISTS, INC. 726 CENTRAL FLORIDA PARKWAY ORLANDO, FLORIDA EVALUATION SUBJECT:

REPORT HOLDER: FASTENING SPECIALISTS, INC. 726 CENTRAL FLORIDA PARKWAY ORLANDO, FLORIDA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2328 Reissued 10/2017 This report is subject to renewal 10/2018. DIVISION: 03 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: PASLODE, AN ILLINOIS TOOL WORKS COMPANY

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: PASLODE, AN ILLINOIS TOOL WORKS COMPANY 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3071 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 06 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1352 Reissued 06/2017 This report is subject to renewal 06/2019. DIVISION: 06 00

More information

REPORT HOLDER: BLUE POINT FASTENING, INC YORBA COURT CHINO, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: BLUE POINT FASTENING, INC YORBA COURT CHINO, CALIFORNIA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1530 Reissued 09/2017 This report is subject to renewal 09/2019. DIVISION: 03 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: MITEK USA, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: MITEK USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2362 Reissued 05/2017 This report is subject to renewal 05/2019. SECTION: 06 05 23

More information

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH BRAND FASTENERS

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH BRAND FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3145 Reissued 02/2017 This report is subject to renewal 02/2018. DIVISION: 05 00 00 METALS SECTION:

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: BARRETTE STRUCTURAL DISTRIBUTION, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: BARRETTE STRUCTURAL DISTRIBUTION, INC. 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 43 6587 (56) 699 0543 www.icc es.org ESR 999 Reissued 0/07 This report is subject to renewal 0/08. DIVISION: 06 00 00 WOOD, PLASTICS AND

More information

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT:

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2269 Reissued 02/2017 This report is subject to renewal 02/2019. DIVISION: 03 00

More information

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI LOW-VELOCITY POWER-ACTUATED FASTENERS

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI LOW-VELOCITY POWER-ACTUATED FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1663 Reissued 03/2017 This report is subject to renewal 03/2019. DIVISION: 03 00 00 CONCRETE

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3282 Reissued 10/2016 This report is subject to renewal 10/2018. DIVISION: 06 00

More information

ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years.

ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years. ICC-ES Evaluation Report ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

Trusted SECTION: 04 HILTI, INC. TULSA, Conformity! ICC-ES Evaluation. not specifically. Copyright 2015

Trusted SECTION: 04 HILTI, INC. TULSA, Conformity! ICC-ES Evaluation. not specifically. Copyright 2015 0 ICC ES Report ICC ES (800) 42 6587 (562) 699 054 www.icc es.orgg 000 Most Widely Accepted and Trusted ESR 2269 Reissued 02/205 This report is subject to renewal 02/207. DIVISION: 0 00 00 CONCRETE SECTION:

More information

LEGACY REPORT ER ICC Evaluation Service, Inc. Reissued January 1, Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER ICC Evaluation Service, Inc. Reissued January 1, Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued January 1, 2000 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900 Montclair

More information

LEGACY REPORT ER ICC Evaluation Service, Inc. Reissued October 1, Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER ICC Evaluation Service, Inc. Reissued October 1, Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued October 1, 2007 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900 Montclair

More information

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 5000 SERIES FASTENERS

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 5000 SERIES FASTENERS 0 ICC-ES Report ICC-ES (800) 42-6587 (562) 699-054 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-45 Reissued 06/206 This report is subject to renewal 06/207 DIVISION: 0 00 00CONCRETE SECTION:

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 4 6587 (562) 699 0543 www.icc es.org ESR 3152 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 07 00 00

More information

Legacy report on the 1997 Uniform Building Code, the 2000 International Building Code and the 2000 International Residential Code.

Legacy report on the 1997 Uniform Building Code, the 2000 International Building Code and the 2000 International Residential Code. LEGACY REPORT ER-2895 Reissued March 1, 2004 www.icc-es.org Business/Regional Office 5360 Workman Mill Road, Whittier, California 90601 (562) 699-0543 Regional Office 900 Montclair Road, Suite A, Birmingham,

More information

DIVISION: METALS SECTION: STEEL DECKING REPORT HOLDER: EPIC METALS CORPORATION 11 TALBOT AVENUE RANKIN, PENNSYLVANIA 15104

DIVISION: METALS SECTION: STEEL DECKING REPORT HOLDER: EPIC METALS CORPORATION 11 TALBOT AVENUE RANKIN, PENNSYLVANIA 15104 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2047 Reissued 07/207 This report is subject to renewal 07/209. DIVISION: 05 00 00

More information

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 3000 SERIES FASTENERS

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 3000 SERIES FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3833 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 03 00

More information

ACCEPTANCE CRITERIA FOR METAL PLASTER BASES (LATH) PREFACE

ACCEPTANCE CRITERIA FOR METAL PLASTER BASES (LATH) PREFACE ICC EVALUATION SERVICE, INC. Evaluate P Inform P Protect ACCEPTANCE CRITERIA FOR METAL PLASTER BASES (LATH) AC191 Approved May 2008 Effective June 1, 2008 Previously approved February 2008, October 2007,

More information

EVALUATION REPORT. PFC-5551 Reissued April 1, Filing Category: DESIGN Steel (038)

EVALUATION REPORT. PFC-5551 Reissued April 1, Filing Category: DESIGN Steel (038) ICBO Evaluation Service, Inc. 5360 WORKMAN MILL ROAD WHITTIER, CALIFORNIA 90601-2299 A subsidiary corporation of the International Conference of Building Officials EVALUATION REPORT Copyright 2001 ICBO

More information

DIVISION: FINISHES SECTION: GYPSUM BOARD ACCESSORIES REPORT HOLDER: CONLAB, INC. dba PREST ON CO.

DIVISION: FINISHES SECTION: GYPSUM BOARD ACCESSORIES REPORT HOLDER: CONLAB, INC. dba PREST ON CO. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1812 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 09 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: FOUR SEASONS SOLAR PRODUCTS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: FOUR SEASONS SOLAR PRODUCTS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2445 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 06 00

More information

DIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: CLARKDIETRICH BUILDING SYSTEMS LLC

DIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: CLARKDIETRICH BUILDING SYSTEMS LLC 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2570 Reissued 12/2016 This report is subject to renewal 12/2017. DIVISION: 05 00 00 METALS SECTION:

More information

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI LOW-VELOCITY POWER-ACTUATED FASTENERS

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI LOW-VELOCITY POWER-ACTUATED FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 42-6587 (562) 699-054 www.icc-es.org ESR-1752 Reissued 09/2017 This report is subject to renewal 09/2019. DIVISION: 0 00 00

More information

ESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year.

ESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year. ESR-1967 Reissued January 1, 2008 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: MITEK USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1311 Reissued 06/2017 This report is subject to renewal 06/2019. DIVISION: 06 00

More information

REPORT HOLDER: ispan SYSTEMS LP 70 BRENTWOOD DRIVE PRINCETON, ONTARIO N0J 1V0 CANADA EVALUATION SUBJECT:

REPORT HOLDER: ispan SYSTEMS LP 70 BRENTWOOD DRIVE PRINCETON, ONTARIO N0J 1V0 CANADA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 2-6587 (562) 699-05 www.icc-es.org ESR-787 Issued 07/2017 This report is subject to renewal 07/2018. DIVISION: 05 00 00 METALS

More information

DIVISION: METALS SECTION: METAL FABRICATIONS REPORT HOLDER: QUALITY WAY PRODUCTS, LLC 407 HADLEY STREET HOLLY, MICHIGAN 48442

DIVISION: METALS SECTION: METAL FABRICATIONS REPORT HOLDER: QUALITY WAY PRODUCTS, LLC 407 HADLEY STREET HOLLY, MICHIGAN 48442 0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 1729 Reissued 10/2016 This report is subject to renewal 10/2018. DIVISION: 05 00 00 METALS SECTION:

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I JOISTS REPORT HOLDER: STARK TRUSS COMPANY, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I JOISTS REPORT HOLDER: STARK TRUSS COMPANY, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 2 6587 (562) 699 05 www.icc es.org ESR 2919 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 06 00 00 WOOD,

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I-JOISTS REPORT HOLDER: PACIFIC WOODTECH CORPORATION

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I-JOISTS REPORT HOLDER: PACIFIC WOODTECH CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1225 Reissued 10/2017 This report is subject to renewal 10/2019. DIVISION: 06 00

More information

FROM: PROPOSED SUBSTITUTION: Use HILTI X-CW Ceiling Wire for Suspended Ceiling Systems

FROM: PROPOSED SUBSTITUTION: Use HILTI X-CW Ceiling Wire for Suspended Ceiling Systems DATE: PROJECT: TO: FROM: SUBJECT: HILTI X-CW CEILING WIRE FASTENER SUBSTITUTION REQUEST SPECIFICATION TITLE: SECTION: PAGE: ARTICLE/PARAGRAPH: DESCRIPTION: DESIGN DETAIL NO.: PROPOSED SUBSTITUTION: Use

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1678 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 04 00 00 MASONRY

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: ENERCEPT, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: ENERCEPT, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1780 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 06 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: FCP, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: FCP, INC. 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2937 Reissued 05/2016 This report is subject to renewal 05/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: HILTI, INC.

DIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: HILTI, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 43 6587 (56) 699 0543 www.icc es.org ESR 97 Reissued /7 This report is subject to renewal /8. DIVISION: 05 00 00 METALS SECTION:

More information

REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3275 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 03 00

More information

DIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 42 6587 (562) 699 054 www.icc es.org ESR 247 Reissued 2/207 This report is subject to renewal 2/209. DIVISION: 05 00 00 METALS

More information

SECTION PLATE CONNECTED WOOD TRUSSES

SECTION PLATE CONNECTED WOOD TRUSSES SECTION 06173 PLATE CONNECTED WOOD TRUSSES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Shop fabricated wood trusses for roof and floor framing. 2. Bridging, bracing, and anchorage. B. Related Sections:

More information

ESR-2894 Reissued April 2014 This report is subject to renewal April 1, 2016.

ESR-2894 Reissued April 2014 This report is subject to renewal April 1, 2016. ICC-ES Evaluation Report ESR-894 Reissued April 04 This report is subject to renewal April, 0. www.icc-es.org (800) 4-87 () 99-04 A Subsidiary of the International Code Council DIVISION: 07 00 00 THERMAL

More information

CHAPTER 3 BUILDINGS WITH WOOD FRAMED EXTERIOR WALLS 301 SCOPE

CHAPTER 3 BUILDINGS WITH WOOD FRAMED EXTERIOR WALLS 301 SCOPE CHAPTER 3 BUILDINGS WITH WOOD FRAMED EXTERIOR WALLS WOOD CHAPTER 3 301 SCOPE This chapter prescribes construction requirements for buildings where all exterior walls above the foundation are wood framed

More information

REPORT HOLDER: CALIFORNIA EXPANDED METAL PRODUCTS COMPANY (CEMCO) CROSSROADS PARKWAY NORTH, SUITE 325 CITY OF INDUSTRY, CALIFORNIA 91746

REPORT HOLDER: CALIFORNIA EXPANDED METAL PRODUCTS COMPANY (CEMCO) CROSSROADS PARKWAY NORTH, SUITE 325 CITY OF INDUSTRY, CALIFORNIA 91746 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3016 Reissued 07/2016 This report is subject to renewal 07/2018. DIVISION: 05 00

More information

PFC-5804* Reissued February 1, Filing Category: DESIGN Wood

PFC-5804* Reissued February 1, Filing Category: DESIGN Wood PFC-50* Reissued February 1, 2003 ICBO Evaluation Service, Inc. 530 Workman Mill Road, Whittier, California 9001 www.icboes.org Filing Category: DESIGN Wood PACIFIC WOODTECH CORPORATION PWI JOISTS PACIFIC

More information

ICBO Evaluation Service, Inc Workman Mill Road, Whittier, California *Revised April 2003

ICBO Evaluation Service, Inc Workman Mill Road, Whittier, California *Revised April 2003 PFC-5804* Reissued February 1, 2003 ICBO Evaluation Service, Inc. 5360 Workman Mill Road, Whittier, California 90601 www.icboes.org Filing Category: DESIGN Wood PACIFIC WOODTECH CORPORATION PWI JOISTS

More information

Originally Issued: 05/20/2013 Revised: 07/07/2017 Valid Through: 05/31/ Design

Originally Issued: 05/20/2013 Revised: 07/07/2017 Valid Through: 05/31/ Design BRADY INNOVATIONS, LLC. PROX HEADER SYSTEM CSI Section: 05 05 23 Metal Fastenings 05 40 00 Cold-formed Metal Framing 1.0 RECOGNITION Brady Innovations, LLC s ProX Header System recognized in this report

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: POWERS FASTENERS, INC. 701 EAST JOPPA ROAD TOWSON, MARYLAND 21286

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: POWERS FASTENERS, INC. 701 EAST JOPPA ROAD TOWSON, MARYLAND 21286 0 ICC-ES Report ICC-ES (800) -687 (6) 6-0 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-678 Reissued 0/0 This report is subject to renewal 0/06 DIVISION: 0 00 00 MASONRY SECTION: 0 0.6 MASONRY

More information

POST FRAME BUILDING STANDARDS

POST FRAME BUILDING STANDARDS CASS COUNTY, MISSOURI BUILDING CODES, ENVIRONMENTAL HEALTH AND ZONING DEPARTMENT 30508 S. West Outer Road, Harrisonville, MO 64701 P- (816) 380-8134 F- (816) 380-8130 POST FRAME BUILDING STANDARDS 201.3

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I JOISTS REPORT HOLDER: LOUISIANA PACIFIC CORPORATION

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I JOISTS REPORT HOLDER: LOUISIANA PACIFIC CORPORATION 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1305 Reissued 08/2016 This report is subject to renewal 08/2018. DIVISION: 06 00 00 WOOD, PLASTICS

More information

REPORT HOLDER: JAACO CORPORATION NE 68 TH STREET, SUITE C 130 REDMOND, WASHINGTON EVALUATION SUBJECT:

REPORT HOLDER: JAACO CORPORATION NE 68 TH STREET, SUITE C 130 REDMOND, WASHINGTON EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3009 Reissued 02/2018 This report is subject to renewal 02/2020. SECTION: 03 16 00

More information

WALL CONSTRUCTION CHAPTER 6

WALL CONSTRUCTION CHAPTER 6 CHAPTER 6 WALL CONSTRUCTION SECTION R601 GENERAL R601.1 Application. The provisions of this chapter shall control the design and construction of all walls and partitions for all buildings. R601.2 Requirements.

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: SHAKERTOWN 1992, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: SHAKERTOWN 1992, INC. 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2386 Reissued 04/2016 This report is subject to renewal 04/2018. DIVISION: 07 00 00 THERMAL

More information

Murphy Laminated Veneer Lumber Murphy Engineered Wood Division Revised May 30, 2013

Murphy Laminated Veneer Lumber Murphy Engineered Wood Division Revised May 30, 2013 Murphy Laminated Veneer Lumber PR-L283 Murphy Engineered Wood Division Revised May 30, 2013 Product: 2250F b -1.5E, 2600F b -1.7E, 2750F b -1.8E, 2850F b -1.9E, 2950F b -2.0E, 3100F b -2.0E, and 3100F

More information

Joint Evaluation Report ICC-ES (800) (562)

Joint Evaluation Report ICC-ES (800) (562) 0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-1262 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 06 00 00 DIVISION NAME SECTION: 06 17 33

More information

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT:

REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2184 Reissued 06/2017 This report is subject to renewal 06/2019. DIVISION: 03 00

More information

ESR ICC Evaluation Service, Inc. Issued November 1, 2003 This report is subject to re-examination in one year.

ESR ICC Evaluation Service, Inc. Issued November 1, 2003 This report is subject to re-examination in one year. ESR-1015 Issued November 1, 2003 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California

More information

Originally Issued: 03/13/2015 Revised: 03/10/2017 Valid Through: 03/31/ Description

Originally Issued: 03/13/2015 Revised: 03/10/2017 Valid Through: 03/31/ Description EVALUATION SUBJECT: TILE FLASHING SYSTEM REPORT HOLDER: EcoFasten Solar 4741 W. Polk Street, Ste. 4 Phoenix, AZ 85043 Phone: 888-766-4273 brian@alpinesnowguards.com CSI DIVISION: 06 WOOD AND PLASTICS CSI

More information

Murphy Laminated Veneer Lumber Murphy Engineered Wood Division Revised January 24, 2017

Murphy Laminated Veneer Lumber Murphy Engineered Wood Division Revised January 24, 2017 Murphy Laminated Veneer Lumber PR-L283 Murphy Engineered Wood Division Revised January 24, 2017 Product: 2250Fb-1.5E, 2600Fb-1.7E, 2750Fb-1.8E, 2850Fb-1.9E, 2950Fb-2.0E, 3100Fb-2.0E, and 3100Fb-2.2E Murphy

More information

Joint Evaluation Report ICC-ES (800) (562)

Joint Evaluation Report ICC-ES (800) (562) 0 Joint Evaluation Report ICC-ES (800) -658 (56) 699-05 www.icc-es.org 000 ESR-0 Reissued 0/0 This report is subject to renewal 0/08. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION: 06 6 00 SHEATHING

More information

City of Republic Community Development Girder and Header Spans for Exterior Walls

City of Republic Community Development Girder and Header Spans for Exterior Walls City of Republic Community Development Girder and Header Spans for Exterior Walls Revision Date: January 2017 2012 IRC Table R502.5(1) Girder Spans a and Header Spans a for Exterior Bearing Walls (Maximum

More information

PR-L274 Nordic Structures Revised April 16, 2017

PR-L274 Nordic Structures Revised April 16, 2017 Nordic TM PR-L274 Nordic Structures Revised April 16, 2017 Products: NI-20, 40, 40x, 60, 70, 80, 80x, 90, and 90x Prefabricated Wood I-s Nordic Structures 1100 Avenue des Canadiens-de-Montréal, Suite 504

More information

ATI Evaluation Service A Division of Architectural Testing Certification Services

ATI Evaluation Service A Division of Architectural Testing Certification Services ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 08/09/2014 Issued: 08/09/2013 Visit www.ati-es.com for current status Revised: 08/12/2013 Page 1 of

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (0) 3-87 (562) 699-03 www.icc-es.org ESR-23 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: ROOF PANELS REPORT HOLDER: ROSER CO., LTD.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: ROOF PANELS REPORT HOLDER: ROSER CO., LTD. 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1763 Reissued 05/2017 This report is subject to renewal 05/2018. DIVISION: 07 00 00 THERMAL

More information

LAMINATED VENEER LUMBER

LAMINATED VENEER LUMBER LAMINATED VENEER LUMBER Kerto LVL Beams, Headers, Rafters and Columns for Floor and Roof Applications. USA VERSION KERTO LAMINATED VENEER LUMBER TABLE OF CONTENTS Design Properties... 2 Allowable Uniform

More information

DIVISION: MASONRY SECTION: CONCRETE UNIT MASONRY REPORT HOLDER: 3B CONSTRUCTION SOLUTIONS, INC.

DIVISION: MASONRY SECTION: CONCRETE UNIT MASONRY REPORT HOLDER: 3B CONSTRUCTION SOLUTIONS, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3788 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 04 00

More information

130 MPH EXPOSURE B WFCM GUIDE. Guide to Wood Frame Construction in High Wind Areas for One- and Two-Family Dwellings 2015 EDITION

130 MPH EXPOSURE B WFCM GUIDE. Guide to Wood Frame Construction in High Wind Areas for One- and Two-Family Dwellings 2015 EDITION 130 MPH EXPOSURE B WFCM GUIDE Guide to Wood Frame Construction in High Wind Areas for One- and Two-Family Dwellings 2015 EDITION Updates and Errata While every precaution has been taken to ensure the accuracy

More information

FIGURE R502.2 FLOOR CONSTRUCTION

FIGURE R502.2 FLOOR CONSTRUCTION CHAPTER 5 FLOORS 11 I SECTION R501 GENERAL R501.1 Application. The provisions of this chapter shall control the design and construction of the floors for all buildings including the floors of attic spaces

More information

ICC-ES Evaluation Report Reissued May 1, 2010 This report is subject to re-examination in two years.

ICC-ES Evaluation Report Reissued May 1, 2010 This report is subject to re-examination in two years. ICC-ES Evaluation Report ESR-1255 Reissued May 1, 2010 This report is subject to re-examination in two years. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: AFM CORPORATION

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: AFM CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2233 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 06 00

More information

DIVISION: FINISHES SECTION: GYPSUM BOARD REPORT HOLDER: PANEL REY, S.A.

DIVISION: FINISHES SECTION: GYPSUM BOARD REPORT HOLDER: PANEL REY, S.A. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3831 Reissued 12/2017 This report is subject to renewal 12/2018. SECTION: 09 29 00

More information

DIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL FLOOR DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER:

DIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL FLOOR DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2050 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 05 00

More information

REPORT HOLDER: LOUISIANA-PACIFIC CORPORATION 414 UNION STREET, SUITE 2000 NASHVILLE, TENNESSEE EVALUATION SUBJECT:

REPORT HOLDER: LOUISIANA-PACIFIC CORPORATION 414 UNION STREET, SUITE 2000 NASHVILLE, TENNESSEE EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-3090 Issued 06/2017 This report is subject to renewal 06/2019. DIVISION: 06 00 00 WOOD, PLASTICS

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4042 Issued 07/2017 This report is subject to renewal 07/2018. DIVISION: 04 00 00

More information

ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS PREFACE

ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS PREFACE ICC EVALUATION SERVICE, INC. Evaluate P Inform P Protect ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS AC70 Approved October 2006 Effective January 1, 2007 Previously

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: BARRETTE STRUCTURAL DISTRIBUTION, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: BARRETTE STRUCTURAL DISTRIBUTION, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1035 Reissued 11/2017 This report is subject to renewal 04/2018. DIVISION: 06 00

More information

REPORT HOLDER: GYPSUM ASSOCIATION 962 WAYNE AVENUE, SUITE 620 SILVER SPRING, MARYLAND EVALUATION SUBJECT:

REPORT HOLDER: GYPSUM ASSOCIATION 962 WAYNE AVENUE, SUITE 620 SILVER SPRING, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 338 Reissued 02/208 This report is subject to renewal 02/209. DIVISION: 09 00 00

More information

REPORT HOLDER: RARE MANUFACTURING INC A AVENUE SURREY, BRITISH COLUMBIA V4N 4P2 CANADA EVALUATION SUBJECT: IRONWOOD SHAKE

REPORT HOLDER: RARE MANUFACTURING INC A AVENUE SURREY, BRITISH COLUMBIA V4N 4P2 CANADA EVALUATION SUBJECT: IRONWOOD SHAKE 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2134 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 07 00

More information

Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel ASTM A36, Fy = 36 ksi

Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel ASTM A36, Fy = 36 ksi STRUCTURAL NOTES MATERIAL STRENGTHS Structural Steel Reinforcing Steel Concrete Masonry Structural Lumber Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC DECKING REPORT HOLDER:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC DECKING REPORT HOLDER: 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3168 Reissued 02/2016 This report is subject to renewal 02/2017. DIVISION: 06 00 00 WOOD, PLASTICS

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL SHINGLES REPORT HOLDER: TEFUTE BUILDING MATERIALS COMPANY, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL SHINGLES REPORT HOLDER: TEFUTE BUILDING MATERIALS COMPANY, LLC 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4036 Reissued 05/2018 This report is subject to renewal 05/2019. DIVISION: 07 00

More information

WFCM 130 MPH GUIDE EXPOSURE B WOOD FRAME CONSTRUCTION MANUAL GUIDE TO WOOD CONSTRUCTION IN HIGH WIND AREAS FOR ONE- AND TWO-FAMILY DWELLINGS

WFCM 130 MPH GUIDE EXPOSURE B WOOD FRAME CONSTRUCTION MANUAL GUIDE TO WOOD CONSTRUCTION IN HIGH WIND AREAS FOR ONE- AND TWO-FAMILY DWELLINGS 130 MPH EXPOSURE B GUIDE WFCM WOOD FRAME CONSTRUCTION MANUAL GUIDE TO WOOD CONSTRUCTION IN HIGH WIND AREAS FOR ONE- AND TWO-FAMILY DWELLINGS A F & P A American Forest & Paper Association American Wood

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3200 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 04 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER: 0 Most idely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-687 (62) 699-043 www.icc-es.org ESR-199 Reissued 0/2017 This report is subject to renewal 0/2019. DIVISION: 07 00 00 THERMAL AND MOISTURE

More information

Technical Data for. Headers. and Beams

Technical Data for. Headers. and Beams L A M I N A T E D V E N E E R L U M B E R Technical Data for Headers and Beams E A S T E R N E N G I N E E R E D W O O D P R O D U C T S OUR COMPANY Our total focus on engineered wood products and providing

More information

ADVANCED FRAMING LUMBER

ADVANCED FRAMING LUMBER ADVANCED FRAMING LUMBER When it's built right, it's oncenter! QUALITY SERVICE VALUE Product Guide At A Glance Introduction 2 Design Properties 2 Wall Stud Design Example 3 Studs - Vertical Load 4 Wall

More information

2.2E Parallam PSL Deep Beam

2.2E Parallam PSL Deep Beam #TJ-7001 SPECIFIER S GUIDE 2.2E Parallam PSL Deep Beam Featuring 20" 24" Deep Trus Joist Parallam PSL Beams Ideal for multi-family and light commercial applications Offers high strength and consistent

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: GENTEK BUILDING PRODUCTS, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: GENTEK BUILDING PRODUCTS, INC. 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-1133 Reissued 11/2017 This report is subject to renewal 11/201. DIVISION: 07 00 00

More information

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS SECTION: PRECAST STRUCTURAL CONCRETE SECTION: SITE CAST CONCRETE

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS SECTION: PRECAST STRUCTURAL CONCRETE SECTION: SITE CAST CONCRETE 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2873 Issued 09/2017 This report is subject to renewal 09/2018. DIVISION: 03 00 00

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4105 Issued 08/2017 This report is subject to renewal 08/2018. DIVISION: 04 00 00

More information