SAFETY AND SECURITY FILMS

Transcription

1 981 Joseph E. Lowery Blvd. Atlanta, GA Phone: Fax: Website: This MANU-SPEC utilizes the Construction Specifications Institute (CSI) Project Resource Manual (PRM), including MasterFormat, SectionFormat and PageFormat. A MANU-SPEC is a manufacturer-specific proprietary product specification using the proprietary method of specifying applicable to project specifications and master guide specifications. Optional text is indicated by brackets [ ]; delete optional text in final copy of specification. Specifier Notes precede specification text; delete notes in final copy of specification. Trade/brand names with appropriate product model numbers, styles and types are used in Specifier Notes and in the specification text Article titled Acceptable Material. Metric conversion, where used, is soft metric conversion. This MANU-SPEC specifies security glazing film manufactured by. Revise MANU-SPEC section number and title below to suit project requirements, specification practices and section content. Refer to CSI MasterFormat for other section numbers and titles SAFETY AND SECURITY FILMS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: This Section specifies security glazing film. Specifier Note: Revise Paragraph below to suit project requirements. Add section numbers and titles per CSI MasterFormat and specifiers practice. B. Related Requirements: Specifier Note: Include in this Paragraph only those sections and documents that directly affect the work of this section. If a reader of this section could reasonably expect to find a product or component specified in this section, but it is actually specified elsewhere, then the related section number(s) should be listed in the Subparagraph below. Do not include Division 00 documents or Division 01 sections since it is assumed that all technical sections are related to all project Division 00 documents and Division 01 sections to some degree. Refer to other documents with caution since referencing them may cause them to be considered part of the Contract REFERENCES 1. Section [ Entrances, Storefronts, and Curtain Walls]. 2. Section [ Windows]. 3. Section [ Glazing]. Specifier Note: Define terms that are unique to this Section and are not provided elsewhere in the contract documents. Include in this Article terms that are unique to the work result specified that may not be commonly known in the construction industry. A. Definitions: MANU-SPEC is a registered trademark of Reed Elsevier Inc. The three-part MANU-SPEC format conforms 1

2 1. Visible Light Transmission: Amount of light passing through a material expressed as a percent. The higher the percent, the greater the amount of light transmitted. 2. Visible Light Reflection: Ratio of light reflected away from a material expressed as a percent of the total amount of light striking the material. 3. Solar Heat Gain Coefficient: Measures how much heat from the sun is blocked. SHGC is expressed as a number between 0 and 1. See more at: Yyi0JKf1.dpufe. Specifier Note: Paragraph below may be omitted when specifying manufacturer s proprietary products and recommended installation. Retain References Paragraph when specifying products and installation by an industry reference standard. List retained standard(s) referenced in this section alphabetically. Indicate issuing authority name, acronym, standard designation and title. Establish policy for indicating edition date of standard referenced. Contract Conditions Section References may establish the edition date of standards. This Paragraph does not require compliance with standard(s). It is a listing of all references used in this section. Only include here standards that are referenced in the body of the specification in PARTS 1, 2 and/or 3. Do not include references to building codes at any level. B. Reference Standards: 1. American National Safety Institute (ANSI): ANSI Z Safety Glazing Materials used in Buildings-Safety Performance Specifications and Methods of Test. 2. American Society for Testing and Materials (ASTM): a. ASTM C Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants. b. ASTM C (2011) Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants. c. ASTM D412-06a (2013) Standard Test Method for Vulcanized Rubber and Thermoplastic Elastomers Tension. d. ASTM D Standard Test Method for Tensile Properties of Thin Plastic Sheeting. e. ASTM D Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics. f. ASTM D Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting. g. ASTM D Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting. h. ASTM E84-14 Standard Test Method for Surface Burning Characteristics of Building Materials. i. ASTM E a Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials. j. ASTM E Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes. k. ASTM F (2013) Standard Test Method for Security Glazing Materials and Systems. 3. Consumer Product Safety Commission (CPSC): a. CPSC 16 CFR 1201 Safety Standard for Architectural Glazing. 4. General Services Administration (GSA): a. GSA-TS Standard Test Method for Glazing and Window Systems Subject to Dynamic Overpressure Loadings [ ]. Specifier Note: Article below includes submittal of relevant data to be furnished by Contractor before, during or after construction. Coordinate this article with Architect s and Contractor s duties and responsibilities in Contract Conditions and Section Submittal Procedures SUBMITTALS A. Product Data: Manufacturer s standard specifications and descriptive literature, including: 2

3 1. SPEC-DATA product sheet. 2. Catalog cut-sheets. 3. Sample warranty. Specifier Note: Samples are actual products intended to illustrate the products to be incorporated into the project. Sample submittals are commonly necessary for such characteristics as colors, textures, and other appearance issues. B. Color Samples: 1. Manufacturer s standard security film colors for selection by [Architect]. 2. Manufacturer s standard structural glazing sealant colors for selection by [Architect]. 3. [ ]. Specifier Note: Specify submittals intended to document manufacturer installation, storage and other instructions. C. Manufacturer s Written Instructions, including: 1. Preparation and Installation. 2. Delivery, storage and handling. 3. Maintenance. Specifier Note: Coordinate Article below with Contract Conditions and with Section Warranties. Specifier Note: NGS Warranty requires security film installation by NGS Certified Contractor. D. Warranty: Filled-out by [Owner] [Architect] [Contractor], and forwarded to manufacturer for registration, with copy of installation invoice, within 30-days of installation of security film, including: 1. Manufacturer s [1-year] warranty, from date of substantial completion, covering defects in installation. 2. Manufacturer s [7-year] warranty, from date of substantial completion, covering defects in materials of exterior fragment retention film. 3. Manufacturer s [15-year] warranty, from date of substantial completion, covering defects in materials of interior spall prevention film. 4. Manufacturer s [20-year] warranty, from date of substantial completion, covering defects in materials of structural glazing sealant. 5. [ ] QUALITY ASSURANCE Specifier Note: NGS requires certified installation contractors trained in the requirements of the TRI-SHIELD 3-Part Advanced Security Glazing Film System. A. Installer: Installed by manufacturer or approved by manufacturer, experienced in performing work of this section, and specialized in installation of work similar to that required for this project DELIVERY, STORAGE & HANDLING A. Deliver materials in accordance with manufacturer s written instructions. B. Deliver materials in manufacturer s original packaging with identification labels intact. 3

4 C. Store materials protected from exposure to harmful weather conditions and at temperature conditions in accordance with manufacturer s written instructions. Specifier Note: USGBC s LEED certification includes credits for the diversion of construction waste from landfill. Diversion can be tracked by either weight or volume but must be consistent for all materials. Manufacturer may reclaim packaging and delivery materials for recycling. D. Remove packaging materials from site and dispose of at appropriate recycling facilities. E. [ ]. PART 2 PRODUCTS Specifier Note: Retain Article below for proprietary method specification. Add product attributes, performance characteristics, material standards and descriptions as applicable. Use of such phrases as or equal, approved equal or similar phrases may cause ambiguity in specifications. Such phrases require verification (procedural, legal and regulatory) and assignment of responsibility for determining or equal products SECURITY FILMS Specifier Note: Include in the following Paragraph manufacturer s name, address, phone number, fax number, address and website URL. A. Manufacturer:. 1. Contact: 981 Joseph E. Lowery Blvd, Atlanta, GA 30318; Telephone: ; Fax: ; security@nationalglazingsolutions.com; Website: Specifier Note: Substitution procedures must either be in the Contract Conditions or in Section Substitution Procedures. Do not include substitution procedures here. 2. Single Source Responsibility: Provide components and materials specified in this section from a single manufacturer. 3. Substitutions: No substitutions permitted. Specifier Note: Include an overall description of the system, assembly, product or material. Include required properties or characteristics that do not obviously belong under other titles. Examples: Configuration, size and color. Specifier Note: B. TRI-SHIELD 3-Part Advanced Security Glazing Film System: Field-applied security film system designed to improve glass retention during break-in attempts at glazing systems and existing security film installations. C. Description: 1. Material: a. Exterior fragment retention film: 1) Material(s): Optical quality biaxially-oriented polyethylene terephthalate (PET). 2) Thickness: 8 mil (0.008 mm). 3) Weight: ounces/feet 2 (29.9 gr/feet 2 ). 4) Size: inches ( mm) 5) Thickness: mm. 6) Ply: 2-ply, (4 mil each ply). 7) Ply Adhesion: Acrylic laminating adhesive. 8) Outermost layer: Photochemically and UV-cured scratch-resistant coating. 4

5 9) Innermost (adhesion) layer: Acrylic pressure-sensitive mounting adhesive. b. Interior spall prevention film: 1) Material(s): Optical quality biaxially-oriented polyethylene terephthalate (PET). 2) Thickness: 8 mil (0.008 mm). 3) Weight: ounces/feet 2 (29.9 gr/feet 2 ). 4) Size: inches ( mm) 5) Thickness: mm. 6) Ply: 2-ply, (4 mil each ply). 7) Ply Adhesion: Acrylic laminating adhesive. 8) Outermost layer: Photochemically and UV-cured scratch-resistant coating. 9) Innermost (adhesion) layer: Acrylic pressure-sensitive mounting adhesive. c. Structural glazing sealant: Dow Corning 995 Structural Sealant. 1) Material: Silicone elastomer. Specifier Note: Select color for exterior fragment retention film, interior spall prevention film, and structural glazing sealant. 2. Color: a. Exterior fragment retention film: [Clear] [Neutral Heat Control (45 percent Grey)] [Privacy Heat Control (20 percent Silver)]. b. Interior spall prevention film: [Clear] [Neutral Heat Control (45 percent Grey)] [Privacy Heat Control (20 percent Silver)]. c. Structural glazing sealant: [Black] [Gray] [White]. Specifier Note: Select Color Properties for selected film color. 3. Color Properties: Clear. a. Visible light transmission: 81.1 percent. b. Visible light reflection exterior: 10.1 percent. c. Visible light reflection interior: 10.1 percent. d. Solar heat gain coefficient: Color Properties: Neutral Heat Control. a. Visible light transmission: 50 percent. b. Visible light reflection exterior: 13.1 percent. c. Visible light reflection interior: 13 percent. d. Solar heat gain coefficient: 0.53] 5. Color Properties: Privacy Heat Control. a. Visible light transmission: 18.4 percent. b. Visible light reflection exterior: 53.8 percent. c. Visible light reflection interior: 57.5 percent. d. Solar heat gain coefficient: 0.24] 6. Performance: a. Exterior fragment retention film: 1) ANSI Z97.1: Unlimited. 2) ASTM D882-12: 240 lb./in. (20.8 kg/mm) breaking strength. 3) ASTM D : Less than 5 percent haze. 4) ASTM D : Greater than 18 lb./ft.² (87.8 kg/m²). 5) ASTM D : 7.4 lb./ft.² (36 kg/m²) average. 5

6 6) ASTM E84-14: A Rating. 7) [ ]. b. Interior spall prevention film: 1) 1) ANSI Z97.1: Unlimited. 2) ASTM D882-12: 32,000 lb./in.² (22.5 kg/mm²) tensile strength. 3) ASTM D : Less than 5 percent haze. 4) ASTM E84-14: A Rating. 5) ASTM E a: Category B (Spall film tested with structural glazing sealant). 6) ASTM E : Category B (Spall film tested with structural glazing sealant). 7) CPSC 16 CFR 1201: Category II. 8) GSA-TS : 3A (4 lb./in.² ( kg/mm²)/28 lb./in.² ( kg/mm²)-ms; spall film tested with structural glazing sealant). 9) [ ]. c. Structural glazing sealant: 1) ASTM C794-10: 40 lb./in. (3.5 kg/mm) after 7-day cure. 2) ASTM C (2011): 50 lb./in.² ( kg/mm²) tensile strength (25 percent elongation) after 7-day cure. 3) ASTM D412-06a (2013): 350 lb./in.² ( kg/mm²) tensile strength after 7-day cure. 4) [ ]. d. TRI-SHIELD System: 1) ASTM F (2013): Passed 1.0 Body Passage. 2) [ ]. PART 3 EXECUTION 3.01 EXAMINATION A. Verify that conditions of substrates previously installed under other sections or contracts are acceptable for product installation in accordance with manufacturer s written instructions prior to installation of security film. 1. Notify [Architect] of unacceptable conditions upon discovery. 2. Proceed with installation only after unacceptable conditions have been corrected. Specifier Note: Specify actions required to prepare the surface, area or site for incorporation of the section s primary products. Describe requirements for exposure or removal of existing assemblies, components, products or materials PREPARATION Specifier Note: Specify preparatory work required prior to installation/application/erection of primary products. A. Prepare substrates to receive security film in accordance with manufacturer s written instructions and approved submittals INSTALLATION A. Install security film in accordance with manufacturer s written instructions and approved submittals. B. Accurately fit, align, securely fasten and install free from distortion or defects. C. [ ]. 6

7 3.04 CLEANING A. Perform daily progress cleaning. B. Upon completion, remove surplus materials, rubbish, tools and equipment. C. Collect recyclable waste and dispose of at appropriate recycling facilities. D. [ ]. Specifier Note: Specify protection methods completed after installation, but prior to acceptance by the owner. Protection of surrounding areas and surfaces during application or installation is included under PART 3, Preparation. Include only statements unique to this Section. Specifier Note: Coordinate the following Article with Section Protecting Installed Construction PROTECTION A. Protect installed product from damage during construction in accordance with manufacturer s written instructions. B. Repair or replace adjacent materials damaged by installation of security film. C. [ ] MAINTENANCE A. Maintain security film system in accordance with manufacturer s instructions [and terms of warranty]. 1. Do not clean security film for 30-days after installation to allow sufficient time for proper curing of film adhesive to glass surfaces. 2. Do not use bristle brushes, scrubbing sponges, abrasive cleaners, pads, or other cleaning materials that could scratch the film. 3. Wash and dry security film with common household window cleaning solutions, and clean soft fabric materials. 4. Inspect security film system every [12] months to verify integrity of sealants, and overall condition of security film system. END OF SECTION 7